Comparison of dynamic effects of high-speed traffic load on ballasted track using a simplified two-dimensional and full three-dimensional model.

The vertical dynamic actions transmitted by railway vehicles to the ballasted track infrastructure is evaluated taking into account models with different degree of detail. In particular, we have studied this matter from a two-dimensional (2D) finite element model to a fully coupled three-dimensional (3D) multi-body finite element model. The vehicle and track are coupled via a non-linear Hertz contact mechanism. The method of Lagrange multipliers is used for the contact constraint enforcement between wheel and rail. Distributed elevation irregularities are generated based on power spectral density (PSD) distributions which are taken into account for the interaction. The numerical simulations are performed in the time domain, using a direct integration method for solving the transient problem due to the contact nonlinearities. The results obtained include contact forces, forces transmitted to the infrastructure (sleeper) by railpads and envelopes of relevant results for several track irregularities and speed ranges. The main contribution of this work is to identify and discuss coincidences and differences between discrete 2D models and continuum 3D models, as wheel as assessing the validity of evaluating the dynamic loading on the track with simplified 2D models

Accurate pedestrian indoor navigation by tightly coupling foot-mounted IMU and RFID measurements

We present a new method to accurately locate persons indoors by fusing inertial navigation system (INS) techniques with active RFID technology. A foot-mounted inertial measuring units (IMUs)-based position estimation method, is aided by the received signal strengths (RSSs) obtained from several active RFID tags placed at known locations in a building. In contrast to other authors that integrate IMUs and RSS with a loose Kalman filter (KF)-based coupling (by using the residuals of inertial- and RSS-calculated positions), we present a tight KF-based INS/RFID integration, using the residuals between the INS-predicted reader-to-tag ranges and the ranges derived from a generic RSS path-loss model. Our approach also includes other drift reduction methods such as zero velocity updates (ZUPTs) at foot stance detections, zero angular-rate updates (ZARUs) when the user is motionless, and heading corrections using magnetometers. A complementary extended Kalman filter (EKF), throughout its 15-element error state vector, compensates the position, velocity and attitude errors of the INS solution, as well as IMU biases. This methodology is valid for any kind of motion (forward, lateral or backward walk, at different speeds), and does not require an offline calibration for the user gait. The integrated INS+RFID methodology eliminates the typical drift of IMU-alone solutions (approximately 1% of the total traveled distance), resulting in typical positioning errors along the walking path (no matter its length) of approximately 1.5 m.

Modeling and Simulation of Upper Brachial Plexus Injury

This article presents the first musculoskeletal model and simulation of upper plexus brachial injury. From this model is possible to analyse forces and movement ranges in order to develop a robotic exoskeleton to improve rehabilitation. The software that currently exists for musculoskeletal modeling is varied and most have advanced features for proper analysis and study of motion simulations. Whilst more powerful computer packages are usually expensive, there are other free and open source packages available which offer different tools to perform animations and simulations and which obtain forces and moments of inertia. Among them, Musculoskeletal Modeling Software was selected to construct a model of the upper limb, which has 7 degrees of freedom and 10 muscles. These muscles are important for two of the movements simulated in this article that are part of the post-surgery rehabilitation protocol. We performed different movement animations which are made using the inertial measurement unit to capture real data from movements made by a human being. We also performed the simulation of forces produced in elbow flexion-extension and arm abduction-adduction of a healthy subject and one with upper brachial plexus injury in a postoperative state to compare the force that is capable of being produced in both cases.

Dynamic Analysis of high Speed Railway Traffic Loads on Ballasted Track

This paper reports the studies carried out to develop and calibrate the optimal models for the objectives of this work. In particular, quarter bogie model for vehicle, rail-wheel contact with Lagrangian multiplier method, 2D spatial discretization were selected as the optimal decisions. Furthermore, the 3D model of coupled vehicle-track also has been developed to contrast the results obtained in the 2D model. The calculations were carried out in the time domain and envelopes of relevant results were obtained for several track profiles and speed ranges. Distributed elevation irregularities were generated based on power spectral density (PSD) distributions. The results obtained include the wheel-rail contact forces, forces transmitted to the bogie by primary suspension. The latter loads are relevant for the purpose of evaluating the performance of the infrastructure

Deployment of an all-in-one millimetre-wave anechoic chamber

This paper describes the new anechoic chamber available at The University of Kent, UK. This facility includes a spherical near/far field, planar near field, cylindrical near field and a compact range. The facility allows measurement from 600 MHz up to 110 MHz. The spherical, planar and cylindrical ranges covers up to 40 GHz and the compact range is available from 50 GHz up to 110 MHz. Immediate plans are to use the new facility to measure body-centric antennas and sensing nodes together with near field sampling of finite sized Frequency Selective Surfaces.

Fractal analysis of laplacian pyramidal filters applied to segmentation of soil images

The laplacian pyramid is a well-known technique for image processing in which local operators of many scales, but identical shape, serve as the basis functions. The required properties to the pyramidal filter produce a family of filters, which is unipara metrical in the case of the classical problem, when the length of the filter is 5. We pay attention to gaussian and fractal behaviour of these basis functions (or filters), and we determine the gaussian and fractal ranges in the case of single parameter ?. These fractal filters loose less energy in every step of the laplacian pyramid, and we apply this property to get threshold values for segmenting soil images, and then evaluate their porosity. Also, we evaluate our results by comparing them with the Otsu algorithm threshold values, and conclude that our algorithm produce reliable test results.

Comparativa de las medidas de emisiones electromagnéticas en las normativas europea y americana para teléfonos duales

El objetivo del presente Proyecto Fin de Grado es la realización de una comparativa de los resultados obtenidos en las medidas de SAR (tasa de absorción específica) y potencia utilizando la normativa europea CENELEC (basada en la del IEC) y la americana FCC (basada en la del IEEE) para distintos dispositivos móviles duales. En primer lugar se ha realizado el estudio de sus características de potencia y de SAR, viendo la variación que hay con respecto a las distintas normativas y rangos de frecuencias. En algunos casos, aunque funcionan sin problema alguno en las diferentes bandas, la diferencia de niveles de emisiones obtenidos en las diferentes bandas puede ser notable. Como se ha comentado al comienzo, se han utilizado diferentes dispositivos duales y se realizaron en ellos las medidas pertinentes utilizando las diferentes normativas y el procedimiento indicado en cada una de ellas. Para observar las diferencias concretas que pudieran existir al utilizar las diferentes normativas, las medidas se han realizado en todas las bandas de funcionamiento del dispositivo y para cada una de ellas se han aplicado las diferentes normativas. Con esto se pretende evaluar si pudiera existir alguna discrepancia en los dispositivos que tienen el certificado de conformidad para una norma concreta cuando se utiliza en otra banda que no es exactamente la banda de utilización de esa norma. En resumen, se quería comprobar que un dispositivo que está certificado con la norma de una región, por ejemplo Europa (900 y 1800 MHz), también cumple si se utiliza en otra región, por ejemplo América (850 y 1900 MHz). La realización práctica del presente PFG se ha hecho en las instalaciones del Laboratorio de Radiofrecuencia de la Secretaría de Estado de Telecomunicación y para la Sociedad de la Información ubicado en El Casar (Guadalajara). En concreto se utilizó el robot articulado movible DASY4 y el software para su control DASY 52.8, disponible en el “banco de medida de Campos Electromagnéticos (Sala de SAR)”. La duración estimada del presente PFG ha sido aproximadamente de cuatro meses. Para llevar a cabo el presente PFG, se dispuso de todo tipo de material y recursos puestos a disposición por el Ministerio de Industria, Turismo y Comercio en el propio laboratorio, así como de los distintos terminales móviles duales con los que se realizaron las medidas pertinentes. Como bibliografía básica se han utilizado las diferentes normas indicadas anteriormente, es decir la norma europea CENELEC (basada en la del IEC) y la americana FCC (basada en la del IEEE), así como manuales de los equipos implicados en el bando de medida de SAR: analizadores de redes, robot articulado y software de control, así como el resto de dispositivos utilizados en las medidas. ABSTRACT. The goal of this Final Degree Project is to perform a comparison of the results obtained in SAR measurements (specific absorption rate) and power using the European standards CENELEC (based on IEC Regulation) and the American FCC (based on IEEE Regulation) to different mobile dual devices. If first place it was made the study of its power and SAR features, seeing that there is shift with respect to the different standards and frequency ranges. In some cases, although they work without any problem in different bands, the difference in levels of emissions obtained in the different bands can be significant. As mentioned at the beginning, different dual devices were used and relevant measurements were taken from them using the different standards and the procedure in each one of them. To see the specific differences that may exist when using the different standards, the measurements were made in all bands of the device operation and to each one it has been applied in the different standards. This attempted to assess whether there could be some discrepancy in the devices that have the certificate of compliance to a specify standard when used in another band that is not exactly the used band of this standard. To sum up, it was required to verify that a device which is certified to the standard of a region, for example (900 and 1800 MHz), also verifies if it is used in another region, for example America (850 and 1900 MHz). The practical realization of this Final Degree Project was made in the facilities of the Radio Frequency Laboratory of the Ministry of State for Telecommunications and the Information Society located in El Casar (Guadalajara). Specifically, the movable articulated robot DASY4 was used and the control software DASY 52.8, available in the “Measure Electromagnetic Field testbench (SAR room)”. The duration of this Final Degree Project has benn about four months. To carry out the present project, all kinds of materials and resources were provided by the Ministry of Industry, Tourism and Trade in its own laboratory, as well as the different mobile dual terminals with which relevant measurements were made. As basic references the different standards indicated above has been used, that is to say the European standard CENELEC (based on IEC standard) and the American FCC (based on IEEE standard), as well as the equipment manuals involved in the SAR measure testbench: network analyzers, articulated robot and control software, as well as the rest of the devices used in the measurements.

Tuning of modulation spectrum parameters for voice pathology detection

Acoustic parameters are frequently used to assess the presence of pathologies in human voice. Many of them have demonstrated to be useful but in some cases its results could be optimized by selecting appropriate working margins. In this study two indices, CIL and RALA, obtained from Modulation Spectra are described and tuned using different frame lengths and frequency ranges to maximize AUC in normal to pathological voice detection. After the tuning process, AUC reaches 0.96 and 0.95 values for CIL and RALA respectively representing an improvement of 16 % and 12 % at each case respect to the typical tuning based only on frame length selection.

Propiedades ópticas y estructurales de nanoestructuras de Zn(Cd)(Mg)O

En la presente tesis doctoral se ha realizado un estudio utilizando diferentes técnicas de crecimiento (RPE-MOCVD y spray pyrolysis) y estructuras (nanohilos, pozos y puntos cuánticos y capas) con el objetivo de desarrollar dispositivos que cubran desde el rango visible hasta el ultravioleta. Es por esta razón por la que se han elegido materiales basados en ZnO, debido a la posibilidades que estos ofrecen para variar su bandgap en un amplio rango de energías. Prueba de ello es que en este estudio se ha conseguido cubrir un rango espectral desde 1.86 hasta 4.11 eV, estudiandose además fenómenos físicos como son la difusión e incorporaci ón de la aleación o la adsorción de gases en la super_cie, lo que ha permitido la fabricación de diferentes fotodetectores de gran sensibilidad. Por todo ello, los resultados obtenidos en esta tesis suponen una gran contribución al conocimiento de las propiedades físicas de las aleaciones de Zn(Cd)O y Zn(Mg)O para potenciales aplicaciónes en dispositivos que operen en el rango visible y ultravioleta del espectro, respectivamente. En esta memoria se da en primer lugar una visión de las propiedades de materiales basados en ZnO, entrando en detalle en una de las ventajas que este presenta, la facilidad que tiene este material para formar nanoestructuras. En el capítulo 3 se dan los conceptos teóricos necesarios para comprender las propiedades ópticas de este tipo de materiales, mostrando también los resultados más reseñables obtenidos en ZnO. En los capítulos referentes a los resultados se pueden diferenciar dos grandes bloques. En el primer bloque de resultados se han analizado nanohilos y pozos cuánticos de Zn(Cd)O crecidos por la técnica de RPE-MOCVD (Capítulos 4 y 5). En el segundo se expondrá el estudio realizado sobre capas y puntos cuánticos de Zn(Mg)O crecidos por la técnica spray pyrolysis como se describe en mayor detalle a continuación. Nanohilos y pozos cuánticos de Zn(Cd)O crecidos por RPE-MOCVD Teóricamente aleando el ZnO con CdO es posible disminuir el valor del band- gap desde 3.37 eV hasta 0.95 eV, cubriendo por completo el espectro visible. El desarrollo del ternario Zn(Cd)O permitiría la fabricación de heteroestructuras y pozos cuánticos, muy importantes en el desarrollo de dispositivos optoelectrónicos que cubran la parte visible del espectro. Sin embargo, la diferencia de estructura cristalina entre estos dos materiales junto a la baja solubilidad del Cd y su alta presión de vapor, di_culta la obtención de material de alta calidad cristalina con alto contenido en Cd. En esta tesis doctoral se ha realizado una completa caracterización óptica y estructural de nanohilos de Zn(Cd)O credidos por la técnica de RPE-MOCVD. Estos nanohilos tinene unas longitudes comprendidas entre 1 y 3 _m y diámetros entre 100 y 200 nm. La concentración máxima introducida de Cd en estas estructuras ha sido de hasta un 54% manteniendo la estructura wurtzita del ZnO, siendo este el mayor contenido de Cd introducido hasta la fecha en nanostructuras basada en ZnO. Este hecho se traduce en una variación de la energía de emisión entre 3.31 y 1.86 eV con el aumento en Cd. El uso de diferentes técnicas de alta resoluci ón de caracterización estructural ha permitido demostrar la presencia de una sola fase estructural wurtzita sin observarse ningún indicio de separación de fases ni acumulación de Cd a lo largo del nanohilo para todos los contenidos de Cd. Con el propósito de fabricar dispositivos en nanohilos individuales, parte de esta tesis doctoral ha estado dedicada a estudiar el impacto que el recocido térmico tiene en las propiedades ópticas y eléctricas de nanohilos de Zn(Cd)O. El recocido térmico es un proceso clave en la optimización de dispositivos, ya sea para la obtenci ón de contactos óhmicos, reducción de defectos o difusión de dopantes por ejemplo. En este estudio se ha observado una mejora muy signi_cativa de las propiedades de emisión de los nanohilos cuando estos eran recocidos a temperaturas mayores que la de crecimiento (300 oC). En las muestras con Cd se ha observado además que el recocido también produce un desplazamiento de la emisión hacia mayores energías debido a una reducción homogénea del contenido de Cd. Medidas de fotoluminiscencia con resolución temporal muestran el impacto que tiene la localización del excitón en las _uctuaciones de potencial, debidas a una distribución estadística del Cd, en la dinámica de los portadores. Comparando el tiempo de vida de los portadores entre los nanohilos recocidos y sin recocer se ha observado un aumento de este parámetro en las estructuras recocidas. Este aumento es fundamentalmente debido a una reducción de centros de recombinación no radiativa asociados a defectos presentes a lo largo del nanohilo. Además, se ha estudiado la evolución de los tiempos de vida de los portadores en función de la temperatura, registrándose una menor estabilidad con la temperatura de los tiempos de vida en las muestras recocidas. Este resultado sugiere que el recocido térmico consigue reducir parte del desorden de la aleación en la estructura. Tras haber caracterizados los nanohilos se desarrollaron una serie de procesa dos para la fabricación de dispositivos basados en nanohilos individuales. Se fabricaron en concreto fotodetectores sensibles al UV, en los que se observó también la alta sensibilidad que muestran a la adsorción de gases en la super_cie, incrementada por la gran relación super_cie/volúmen característica de las nanoestructuras. Estos procesos de adsorción observados tienen un impacto directo sobre las propiedades ópticas y electricas de los dispositivos como se ha demostrado. Por ello que en esta tesis se hayan estudiado en detalle este tipo de procesos, ideando maneras para tener un mayor control sobre ellos. Finalmente se crecieron estructuras de pozos cuántico de ZnCdO/ZnO en nanohilos con contenidos de Cd nominales de 54 %. Las medidas ópticas realizadas mostraron como al aumentar la anchura del pozo de 0.7 a 10 nm, la emisión relacionada con el pozo se desplazaba entre 3.30 y 1.97 eV. Este gran desplazamiento representa el mayor obtenido hasta la fecha en pozos cuánticos de ZnCdO/ZnO. Sin embargo, al caracterizar estructuralmente estas muestras se observó la presencia de procesos de difusión de Cd entre el pozo y la barrera. Como se ha podido medir, este tipo de procesos reducen sustancialmente la concentración de Cd en el pozo al difundirse parte a la barrera. cambiando completamente la estructura de bandas nominal de estas estructuras. Este estudio demuestra la importancia del impacto de los procesos de difusión en la interpretación de los efectos de con_namiento cuántico para este tipo de estructuras. Capas y puntos cuánticos de Zn(Mg)O crecidos por spray pyrolysis La técnica de spray pyrolysis, debido a su simplicidad, bajo coste y capacidad de crecer sobre grandes áreas conservando una alta calidad cristalina presenta un gran interés en la comunidad cientí_ca para el potencial desarrollo de dispositivos comerciales. En esta tesis se ha estudiado las propiedades ópticas y eléctricas de capas y puntos cuánticos de Zn(Mg)O crecidos por esta técnica. Al contrario que pasa con el Cd, al introducir Mg en la estructura wurtzita de ZnO se consigue aumentar el bandgap del semiconductor. Sin embargo, al igual que pasa con el CdO, la diferencia de estructura cristalina entre el ZnO y el MgO limita la cantidad de Mg que se puede incorporar, haciendo que para una cierta concentración de Mg aparezcan el fenómeno de separación de fases. En esta tesis se ha conseguido incorporar hasta un contenido de Mg del 35% en la estructura wurtzita del ZnO utilizando la técnica de spray pyrolysis, resultado que representa la mayor concentración de Mg publicada hasta la fecha. Este hecho ha posibilitado variar la energía del borde de absorción desde 3.30 a 4.11 eV. En estas capas se ha realizado una completa caracterización óptica observándose una diferencia entre las energías del borde de absorción y del máximo de emisión creciente con el contenido en Mg. Esta diferencia, conocida como desplazamiento de Stokes, es debida en parte a la presencia de _uctuaciones de potencial producidas por un desorden estadístico de la aleación. Se han fabricado fotodetectores MSM de alta calidad utilizando las capas de Zn(Mg)O previamente caracterizadas, observándose un desplazamiento del borde de absorción con el aumento en Mg desde 3.32 a 4.02 eV. Estos dispositivos muestran altos valores de responsividad (10-103 A/W) y altos contrastes entre la responsividad bajo iluminación y oscuridad (10-107). Estos resultados son en parte debidos a la presencia de mecanismos de ganancia y una reducción de la corriente de oscuridad en las muestras con alto contenido de Mg. Utilizando esta misma técnica de crecimiento se han crecido puntos de Zn(Mg)O con concentraciones nominales de Mg entre 0 y 100 %, con dimensiones medias entre 4 y 6 nm. Las medidas estructurales realizadas muestran que hasta un valor de Mg de 45 %, los puntos están compuestos por una única fase estructural, wurtzita. A partir de esa concentración de Mg aparece una fase cúbica en los puntos, coexistiendo con la fase hexagonal hasta una concentración nominales del 85 %. Para concentraciones mayores de Mg, los puntos muestran una única fase estructural cúbica. Medidas de absorción realizadas en estos puntos de Zn(Mg)O muestran un desplazamiento del borde de absorción entre 3.33 y 3.55 eV cuando la concentraci ón de Mg en los puntos aumenta hasta el 40 %. Este desplazamiento observado es debido solamente a la fase wurtzita del Zn(Mg)O donde se incorpora el Mg. ABSTRACT This PhD theis presents a study using di_erent growth techniques (RPEMOCVD and spray pyrolysis) and structures (nanowires, quantum dots and wells and layers) in order to develop devices that extend from the visible to the ultraviolet range. For this reason ZnO based materials have been choosen, because they o_er the possibility to tunne the bandgap in this energy range. Proof of this is that this study has managed to cover a spectral range from 1.86 to 4.11 eV, also being studied physical phenomena such as di_usion and incorporation of alloy or adsorption of gases on the surface, allowing the develop di_erent highly sensitive photodetectors. Therefore, the results obtained in this thesis are a great contribution two large blockso the knowledge of the physical properties of alloys Zn(Cd)O and Zn(Mg)O for potential applications in devices that operate in the visible and ultraviolet range, respectively. In the _rst chapter, the general properties of ZnO-based materials are presented, showing the facilities that these kind of materials o_er to obtain di_erent nanoestructures. In Chapter 3, optical theoretical concepts are given to understand the optical properties of these materials, also showing the most signi_cant results of ZnO. In the chapters related with the results, two blocks could be distinguish. In the _rst one, Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD have been analyzed (Chapters 4 and 5). The second block of results shows the study performed in Zn(Mg)O _lms and quantum dots grown by spray pyrolysis. Zn(Cd)O nanowires and quantum wells grown by RPE-MOCVD In summary, the results of the PhD thesis are a great contribution to the knowledge of the physical properties of Zn(Cd)O and Zn(Mg)O alloys and their application for high performance devices operating in the visible and UV ranges, respectively. The performance of the device is still limited due to alloy solubility and p-doping stability, which opens a door for future research in this _eld. Theoretically, annealing ZnO with CdO allows to reduce the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. The development of ZnCdO alloys allows the fabrication of heterostructures and quantum wells, necessary for the development of high performance optoelectronic devices. However, the di_erent crystal structures between CdO and ZnO and the low solubility of Cd and its high vapor pressure, hinders the growth of ZnCdO alloys with high Cd contents. In this PhD thesis Zn(Cd)O nanowires have been optically and structurally characterized, obtaining a maximum Cd content of 54% while maintaining their wurtzite structure. This Cd content, which allows lowering the bandgap down to 1.86 eV, is the highest concentration ever reported in nanostructures based on ZnO. The combination of optical and structural characterization techniques used during this thesis has allowed the demonstration of the presence of a single wurtzite structure, without observing any indication of phase separation or Cd accumulation along the nanowire. Annealing processes are essential in the fabrication of optoelectronic devices. For this reason, a complete study of the annealing e_ects in the optical and electrical properties of Zn(Cd)O nanowires has been performed. In the _rst place, annealing nanowires at higher temperatures than their growth temperature (300 oC) allows a signi_cant improvement of their emission properties. However, in the samples that contain Cd a shift in the emission towards higher energies has been observed due to a homogeneous reduction of the Cd content in the nanowires. Time resolved photoluminescence measurements show the impact of the exciton localization in the potential _uctuations due to a statistical alloy disorder. An increase in the carrier lifetime has been obtained for the annealed nanowires. This increase is mainly due to the reduction of non-radiative recombination centers associated with the defects present in the material. Furthermore, temperature dependent time resolved photoluminescence measurements suggest a reduction of the alloy disorder in the annealed samples. In this thesis, single nanowire photodetectors with a high responsivity in the UV range have been demonstrated. Due to the high surface/volume ratio, these structures are very sensitive to gas adsorption at the surface, which largely de_nes the optical and electrical properties of the material and, therefore, of the device. With the aim of obtaining time stable devices, the dynamic adsorption-desorption processes have been studied, developing di_erent approaches that allow a higher control over them. Finally, ZnCdO/ZnO quantum wells have been grown with a nominal Cd concentration of 54% inside the well. The performed optical measurements show that increasing the well width from 0.7 to 10 nm, shifts the emission related with the well from 3.30 to 1.97 eV. This result represents the highest shift reported in the literature. However, a detailed structural characterization shows the presence of di_usion phenomena which substantially reduce the concentration of Cd in the well, while increasing it in the barrier. This type of phenomena should be considered when ac curately interpretating the quantum con_nement e_ects in Zn(Cd)O/ZnO quantum wells. Theoretically, annealing ZnO with CdO allows to decrease the bandgap from 3.37 to 0.95 eV, covering the whole visible spectrum. Zn(Mg)O _lms and quantum dots grown by spray pyrolysis Due to its simplicity, low-cost and capacity to grow over large areas conserving a high crystal quality, spray pyrolysis technique presents a great interest in the scienti_c community for developing comercial devices. In this thesis, a complete study of the optical and structural properties of Zn(Mg)O _lms and quantum dots grown by spray pyrolysis has been performed. Contrary to Zn(Cd)O alloys, when introducing Mg in the ZnO wurtzite structure an increase in the bandgap in obtained. Once again, the di_erence in the crystal structure of ZnO and MgO limits the amount of Mg that can be introduced before phase separation appears. In this PhD thesis, a maximum Mg content of 35% has been incorporated in the wurtzite structure using spray pyrolysis. This variation in the Mg content translates into an increase of the absorption edge from 3.30 to 4.11 eV. Up to this date, this result represents the highest Mg content introduced by spray pyrolysis in a ZnO wurzite structure reported in the literature. The comparison of the emission and absorption spectra shows the presence of an increasing Stokes shift with Mg content. This phenomenon is partialy related with the presence of potential _uctuations due to an statistic alloy disorder. MSM photodetectors have been processed on previously characterized Zn(Mg)O _lms. These devices have shown a shift in the absorption edge from 3.32 to 4.02 eV with the increase in Mg content, high responsivity values (10-103 A/W) and high contrast ratios between illuminated and dark responsivities (10-107). These values are explained by the presence of a gain mechanism and a reduction of dark current in the ZnMgO samples. Zn(Mg)O quantum dots have also been grown using spray pyrolysis with Mg concentrations between 0 and 100% and with average widths ranging 4 to 6 nm. Structural measurements show that at a Mg concentration of 45% the cubic phase appears, coexisting with the hexagonal phase up to an 85% concentration of Mg content. From 85% onwards the quantum dots show only the cubic phase. Absorption measurements performed in these structures reveal a shift in the absorption edge from 3.33 to 3.55 eV when the Mg content increases up to 40 %.

Evaluación de Ulmus pumila L. y Populus spp. como cultivos energéticos en corta rotación

El presente trabajo estudia el empleo del olmo de Siberia (Ulmus Pumila L.) y el chopo (Populus spp.) en corta rotación y alta densidad para la producción de biomasa con fines energéticos. En el área mediterránea las disponibilidades hídricas son limitadas, por lo que la mayoría de los cultivos energéticos utilizados hasta el momento requieren el aporte de agua de riego; por ello resulta fundamental encontrar especies con bajos requerimientos hídricos, analizar la eficiencia en el uso del agua de diferentes materiales genéticos y optimizar la dosis de riego. Las parcelas experimentales se ubicaron en la provincia de Soria. En el ensayo llevado a cabo con olmo de Siberia se ha analizado el efecto en la producción de la disponibilidad de agua mediante el establecimiento de parcelas en secano y con dos dosis de riego (2000 m3 ha-1 año-1 y 4000 m3 ha-1 año-1 aproximadamente); además, al ser una especie poco estudiada hasta el momento, se ha estudiado también el efecto que tiene sobre el rendimiento la densidad de plantación (3.333 plantas ha-1 y 6.666 plantas ha-1), el tipo de suelo (2 calidades diferentes) y el turno de corta (3 y 4 años). En el caso del chopo, se han evaluado cuatro clones (AF-2, I-214, Monviso y Pegaso) establecidos con una densidad de 20.000 plantas por hectárea. Durante el primer ciclo de tres años se aportó el mismo volumen de riego a todas las parcelas, mientras que durante el segundo ciclo se establecieron 8 regímenes hídricos diferentes. Por otra parte, se ha investigado sobre el uso del potencial hídrico de las plantas para evaluar el estrés hídrico de las mismas y se ha estimado la producción de biomasa foliar y el Índice de Área Foliar (LAI) de ambas especies, relacionando los valores obtenidos con la dosis de riego y la producción de biomasa. Los resultados muestran que los suelos inundados reducen la tasa de supervivencia de los olmos durante el periodo de implantación, sin embargo la mortalidad durante los siguientes periodos vegetativos es baja y muestra buena capacidad de rebrote. La productividad (kg ha-1 año-1) obtenida fue mayor con un turno de corta de cuatro años que con turno de tres años. El área basal y la altura fueron variables eficaces para predecir la producción de biomasa del olmo de Siberia, obteniendo una variabilidad explicada de más del 80%. En cuanto a los parámetros que mayor influencia tuvieron sobre el crecimiento, el tipo de suelo resulto ser el más relevante, obteniéndose en un suelo agrícola considerado de buena calidad una producción en condiciones de secano de unos 8.000 kg ha-1 año-1. En condiciones de regadío el rendimiento del olmo de Siberia fue al menos el doble que en secano, pero la diferencia entre las dos dosis de riego estudiadas fue pequeña. La producción de biomasa fue mayor en la densidad de plantación más alta (6.666 plantas ha–1) en las parcelas de regadío, sin embargo no se encontraron diferencias significativas entre las dos densidades en secano. El clon de chopo que presentó un mayor rendimiento durante el primer ciclo fue AF-2, alcanzando los 14.000 kg ha-1 año-1, sin embargo la producción de este clon bajó sustancialmente durante el segundo ciclo debido a su mala capacidad de rebrote, pasando a ser I-214 el clon más productivo llegando también a los 14.000 kg ha-1 año-1. Un aporte adicional de agua proporcionó un incremento de la biomasa recogida, pero a partir de unos 6.500 m3 ha-1 año-1 de agua la producción se mantiene constante. El potencial hídrico foliar ha resultado ser una herramienta útil para conocer el estrés hídrico de las plantas. Los olmos de regadío apenas sufrieron estrés hídrico, mientras que los implantados en condiciones de secano padecieron un acusado estrés durante buena parte del periodo vegetativo, que se acentuó en la parte final del mismo. Los chopos regados con las dosis más altas no sufrieron estrés hídrico o fue muy pequeño, en las dosis intermedias sufrieron un estrés moderado ocasionalmente y únicamente en las dosis más bajas sufrieron puntualmente un estrés severo. El LAI aumenta con la edad de los brotes y oscila entre 2 y 4 m2 m−2 en los chopos y entre 2 y 7 m2 m−2 en los olmos. Se encontró una buena relación entre este índice y la producción de biomasa del olmo de Siberia. En general, puede decirse que el olmo de Siberia podría ser una buena alternativa para producir biomasa leñosa en condiciones de secano, mientras que el chopo podría emplearse en regadío siempre que se haga una buena elección del clon y de la dosis de riego. ABSTRACT This work explores the possibilities of biomass production, for energy purposes, of Siberian elm (Ulmus Pumila L.) and poplar (Populus spp.) in Spain. Irrigation is required for the viable cultivation of many energy crops in Mediterranean areas because of low water availability, for this reason species with low water requirements should be a good alternative for biomass production. Moreover, the optimal amount of irrigation water and the performance of the different genetic material in terms of production and water use efficiency should be studied in order to use water wisely. The experimental plots were established in the province of Soria in Spain. Given the small amount of information available about Siberian elm, besides studying the influence of water availability (rain-fed and two different irrigation doses) on biomass production, two different plantation densities (3,333 plants ha-1 and 6,666 plants ha-1), two different soil type and two cutting cycles (three years and four years) were assessed. In the case of poplar, four clones belonging to different hybrids (I-214, AF2, Pegaso, and Monviso) were included in a high density plantation (20,000 plants ha-1). During the first cycle, the water supplied in all plots was the same, while 8 different watering regimes were used during the second cycle. The suitability of the use of the leaf water potential to assess the water stress situations has also been investigated. Moreover, leaf biomass production and leaf area index (LAI) were estimated in both species in order to analyze the relationship between these parameters, irrigation dose and biomass production. The results shows that flooded soils have an adverse effect on elm survival in the implantation period, but the percentage of mortality is very low during the following vegetative periods and it shows a good ability of regrowth. The annual yield from a four-year cutting cycle was significantly greater than that from the three-year cutting cycle. Basal diameter and height are effective variables for predicting the production of total biomass; equations with R squared higher than 80% were obtained. The analysis of parameters having an influence on elm growth shows that soil type is the most important factor to obtain a good yield. In soils with enough nutrients and higher waterholding capacity, biomass productions of 8,000 kg ha-1 yr-1 were achieved even under rain-fed conditions. In irrigated plots, Siberian elm production was double than the production of biomass under rain-fed conditions; however, small differences were obtained between the 2 different irrigation doses under study. Biomass yield was greater for the highest planting density (6,666 plants ha–1) in irrigated plots, but significant differences were not found between the 2 densities in rain-fed plots. The clone AF-2 showed the highest production (14,000 kg ha-1 yr-1) during the first cycle, however during the second cycle its growth was lower because of a high mortality rate after regrowth and I-214 achieves the greatest production (14,000 kg ha-1 yr-1). An additional water supply provided a greater amount of biomass, but over about 6500 m3 ha-1 yr-1 of water the production is constant. Leaf water potential has been shown to be a useful tool for finding out plant water status. Irrigated elms hardly suffered water stress, while rain-fed elms suffered a pronounced water stress, which was more marked at the end of the vegetative period. Most of poplars did not show water stress; leaf water potentials only showed an important water stress in the plots irrigated with the lowest doses. LAI increases with shoot age and it ranges from 2 to 4 m2 m−2 in poplars and from 2 to 7 m2 m−2 in elms. A good relationship has been found between this index and Siberian elm production. In general, Siberian elm could be a good alternative to produce woody biomass in rainfed plots, while poplar could be used in irrigated plots if a suitable clone and irrigation dose are chosen.

Contribution to the Analysis, Design and Assessment of Compact Antenna Test Ranges At Millimeter Wavelengths - Contribución al Análisis, Diseño y Caracterización de Sistemas de Medida de Antenas en Rango Compacto para Frecuencias Milimétricas

This Doctoral Thesis entitled Contribution to the analysis, design and assessment of compact antenna test ranges at millimeter wavelengths aims to deepen the knowledge of a particular antenna measurement system: the compact range, operating in the frequency bands of millimeter wavelengths. The thesis has been developed at Radiation Group (GR), an antenna laboratory which belongs to the Signals, Systems and Radiocommunications department (SSR), from Technical University of Madrid (UPM). The Radiation Group owns an extensive experience on antenna measurements, running at present four facilities which operate in different configurations: Gregorian compact antenna test range, spherical near field, planar near field and semianechoic arch system. The research work performed in line with this thesis contributes the knowledge of the first measurement configuration at higher frequencies, beyond the microwaves region where Radiation Group features customer-level performance. To reach this high level purpose, a set of scientific tasks were sequentially carried out. Those are succinctly described in the subsequent paragraphs. A first step dealed with the State of Art review. The study of scientific literature dealed with the analysis of measurement practices in compact antenna test ranges in addition with the particularities of millimeter wavelength technologies. Joint study of both fields of knowledge converged, when this measurement facilities are of interest, in a series of technological challenges which become serious bottlenecks at different stages: analysis, design and assessment. Thirdly after the overview study, focus was set on Electromagnetic analysis algorithms. These formulations allow to approach certain electromagnetic features of interest, such as field distribution phase or stray signal analysis of particular structures when they interact with electromagnetic waves sources. Properly operated, a CATR facility features electromagnetic waves collimation optics which are large, in terms of wavelengths. Accordingly, the electromagnetic analysis tasks introduce an extense number of mathematic unknowns which grow with frequency, following different polynomic order laws depending on the used algorithmia. In particular, the optics configuration which was of our interest consisted on the reflection type serrated edge collimator. The analysis of these devices requires a flexible handling of almost arbitrary scattering geometries, becoming this flexibility the nucleus of the algorithmia’s ability to perform the subsequent design tasks. This thesis’ contribution to this field of knowledge consisted on reaching a formulation which was powerful at the same time when dealing with various analysis geometries and computationally speaking. Two algorithmia were developed. While based on the same principle of hybridization, they reached different order Physics performance at the cost of the computational efficiency. Inter-comparison of their CATR design capabilities was performed, reaching both qualitative as well as quantitative conclusions on their scope. In third place, interest was shifted from analysis - design tasks towards range assessment. Millimetre wavelengths imply strict mechanical tolerances and fine setup adjustment. In addition, the large number of unknowns issue already faced in the analysis stage appears as well in the on chamber field probing stage. Natural decrease of dynamic range available by semiconductor millimeter waves sources requires in addition larger integration times at each probing point. These peculiarities increase exponentially the difficulty of performing assessment processes in CATR facilities beyond microwaves. The bottleneck becomes so tight that it compromises the range characterization beyond a certain limit frequency which typically lies on the lowest segment of millimeter wavelength frequencies. However the value of range assessment moves, on the contrary, towards the highest segment. This thesis contributes this technological scenario developing quiet zone probing techniques which achieves substantial data reduction ratii. Collaterally, it increases the robustness of the results to noise, which is a virtual rise of the setup’s available dynamic range. In fourth place, the environmental sensitivity of millimeter wavelengths issue was approached. It is well known the drifts of electromagnetic experiments due to the dependance of the re sults with respect to the surrounding environment. This feature relegates many industrial practices of microwave frequencies to the experimental stage, at millimeter wavelengths. In particular, evolution of the atmosphere within acceptable conditioning bounds redounds in drift phenomena which completely mask the experimental results. The contribution of this thesis on this aspect consists on modeling electrically the indoor atmosphere existing in a CATR, as a function of environmental variables which affect the range’s performance. A simple model was developed, being able to handle high level phenomena, such as feed - probe phase drift as a function of low level magnitudes easy to be sampled: relative humidity and temperature. With this model, environmental compensation can be performed and chamber conditioning is automatically extended towards higher frequencies. Therefore, the purpose of this thesis is to go further into the knowledge of millimetre wavelengths involving compact antenna test ranges. This knowledge is dosified through the sequential stages of a CATR conception, form early low level electromagnetic analysis towards the assessment of an operative facility, stages for each one of which nowadays bottleneck phenomena exist and seriously compromise the antenna measurement practices at millimeter wavelengths.

Analysis and suppression of reflections in far-field antenna measurement ranges

This paper presents the analysis of the reflections in two kind of spherical far field ranges: one if the classical acquisition where the AUT is rotated and the second one corresponds to the systems where the AUT is fixed and the antenna probe is rotated. In large far field systems this is not possible, but this can be used to the measurement of small antennas, for instance, with the SATIMO StarGate system. In both cases, it is assumed that only one frequency is acquired and the results should be improved cut by cut, in order not to lose the advantages or far field measurements. Finally, some practical results are studied using measurements of one antenna in the outdoor far field facility of LIT INPE in Brazil.

Spawning and habitat management in salmonid populations at the southern edge of their natural ranges = Reproducción y gestión del hábitat en poblaciones de salmónidos en el extremo meridional de sus distribuciones naturales

Las poblaciones de salmónidos en la Península Ibérica (trucha común, Salmo trutta; y salmón atlántico, Salmo salar) se encuentran cerca del límite meridional de sus distribuciones naturales, y por tanto tienen una gran importancia para la conservación de estas especies. En la presente Tesis se han investigado algunos aspectos de la reproducción y de la gestión del hábitat, con el objeto de mejorar el conocimiento acerca de estas poblaciones meridionales de salmónidos. Se ha estudiado la reproducción de la trucha común en el río Castril (Andalucía, sur de España), donde se ha observado que la freza ocurre desde diciembre hasta abril con el máximo de actividad en febrero. Este hecho representa uno de los periodos reproductivos más tardíos y con mayor duración de toda la distribución natural de la especie. Además, actualmente se sabe que el resto de poblaciones andaluzas tienen periodos de reproducción similares (retrasados y extendidos). Análisis en la escala de la distribución natural de la trucha común, han mostrado que la latitud explica parcialmente tanto la fecha media de reproducción (R2 = 62.8%) como la duración del periodo de freza (R2 = 24.4%) mediante relaciones negativas: a menor latitud, la freza ocurre más tarde y durante más tiempo. Es verosímil que un periodo de freza largo suponga una ventaja para la supervivencia de las poblaciones de trucha en hábitats impredecibles, y por tanto se ha propuesto la siguiente hipótesis, que deberá ser comprobada en el futuro: la duración de la freza es mayor en hábitats impredecibles que en aquellos más predecibles. La elevada tasa de solapamiento de frezaderos observada en el río Castril no se explica únicamente por una excesiva densidad de reproductores. Las hembras de trucha eligieron lugares específicos para construir sus frezaderos en vez de dispersarse aleatoriamente dentro del hábitat adecuado para la freza que tenían disponible. Estas observaciones sugieren que las hembras tienen algún tipo de preferencia por solapar sus frezaderos. Además, en ríos calizos como el Castril, las gravas pueden ser muy cohesivas y difíciles de excavar, por lo que el solapamiento de frezaderos puede suponer una ventaja para la hembra, porque la excavación en sustratos que han sido previamente removidos por frezas anteriores requerirá menos gasto de energía que en sustratos con gravas cohesivas que no han sido alteradas. Por tanto, se ha propuesto la siguiente hipótesis, que deberá ser comprobada en el futuro: las hembras tienen una mayor preferencia por solapar sus frezaderos en ríos con sustratos cohesivos que en ríos con sustratos de gravas sueltas. En el marco de la gestión del hábitat, se han empleado dos enfoques diferentes para la evaluación del hábitat físico, con el objeto de cuantificar los cambios potenciales en la disponibilidad de hábitat, antes de la implementación real de determinadas medidas sobre el hábitat. En primer lugar, se ha evaluado el hábitat físico del salmón atlántico en el río Pas (Cantabria, norte de España), en la escala del microhábitat, empleando la metodología IFIM junto con un modelo hidráulico bidimensional (River2D). Se han simulado una serie de acciones de mejora del hábitat y se han cuantificado los cambios en el hábitat bajo estas acciones. Los resultados mostraron un aumento muy pequeño en la disponibilidad de hábitat, por lo que no sería efectivo implementar estas acciones en este tramo fluvial. En segundo lugar, se ha evaluado el hábitat físico de la trucha común en el río Tajuña (Guadalajara, centro de España), en la escala del mesohábitat, empleando la metodología MesoHABSIM. Actualmente, el río Tajuña está alterado por los usos agrícolas de sus riberas, y por tanto se ha diseñado una restauración para mitigar estos impactos y para llevar al río a un estado más natural. Se ha cuantificado la disponibilidad de hábitat tras la restauración planteada, y los resultados han permitido identificar los tramos en los que la restauración resultaría más eficaz. ABSTRACT Salmonid populations in the Iberian Peninsula (brown trout, Salmo trutta; and Atlantic salmon, Salmo salar) are close to the southern limit of their natural ranges, and therefore they are of great importance for the conservation of the species. In the present dissertation, some aspects of spawning and habitat management have been investigated, in order to improve the knowledge on these southern salmonid populations. Brown trout spawning have been studied in the river Castril (Andalusia, southern Spain), and it has been observed that spawning occurs from December until April with the maximum activity in February. This finding represents one of the most belated and protracted spawning periods within the natural range of the species. Furthermore, it is now known that the rest of Andalusian populations show similar (belated and extended) spawning periods. Broad-scale analyses throughout the brown trout natural range showed that latitude partly explained both spawning mean time (R2 = 62.8%) and spawning duration (R2 = 24.4%) by negative relationships: the lower the latitude, the later the spawning time and the longer the spawning period. It is plausible that a long spawning period would be an advantage for survival of trout populations in unpredictable habitats, and thus the following hypothesis has been proposed, which is yet to be tested: spawning duration is longer in unpredictable than in predictable habitats. High rate of redd superimposition observed in the river Castril was not only caused by high density of spawners. Trout females chose specific sites for redd construction instead of randomly dispersing over the suitable spawning habitat. These observations suggest that female spawners have some kind of preference for superimposing redds. Moreover, in limestone streams such as Castril, unused gravels can be very cohesive and hard to dig, and thus redd superimposition may be an advantage for female, because digging may require less energy expenditure in already used redd sites than in cohesive and embedded unused sites. Hence, the following hypothesis has been proposed, which is yet to be tested: females have a higher preference for superimposing redds in streambeds with cohesive and embedded substrates than in rivers with loose gravels. Within the topic of habitat management, two different approaches have been used for physical habitat assessment, in order to quantify the potential change in habitat availability, prior to the actual implementation of proposed habitat measures. Firstly, physical habitat for Atlantic salmon in the river Pas (Cantabria, northern Spain) has been assessed at the microhabitat scale, using the IFIM approach along with a two dimensional hydraulic model (River2D). Proposed habitat enhancement actions have been simulated and potential habitat change has been quantified. Results showed a very small increasing in habitat availability and therefore it is not worth to implement these measures in this stream reach. Secondly, physical habitat for brown trout in the river Tajuña (Guadalajara, central Spain) has been assessed at the mesohabitat scale, using the MesoHABSIM approach. The river Tajuña is currently impacted by surrounding agricultural uses, and thus restoration was designed to mitigate these impacts and to drive the river to a more natural state. Habitat availability after the planned restoration has been quantified, and the results have permitted to identify in which sites the restoration will be more effective.