Precision Agriculture without borders: Practical issues and improvements in farmland coverage with aerial vehicles.

This work presents a solution for the aerial coverage of a field by using a fleet of aerial vehicles. The use of Unmanned Aerial Vehicles allows to obtain high resolution mosaics to be used in Precision Agriculture techniques. This report is focus on providing a solution for the full simultaneous coverage problem taking into account restrictions as the required spatial resolution and overlap while maintaining similar light conditions and safety operation of the drones. Results obtained from real field tests are finally reported

A waypoint-based mission planner for a farmland coverage with an aerial robot - a precision farming tool

Remote sensing (RS) with aerial robots is becoming more usual in every day time in Precision Agriculture (PA) practices, do to their advantages over conventional methods. Usually, available commercial platforms providing off-the-shelf waypoint navigation are adopted to perform visual surveys over crop fields, with the purpose to acquire specific image samples. The way in which a waypoint list is computed and dispatched to the aerial robot when mapping non empty agricultural workspaces has not been yet discussed. In this paper we propose an offline mission planner approach that computes an efficient coverage path subject to some constraints by decomposing the environment approximately into cells. Therefore, the aim of this work is contributing with a feasible waypoints-based tool to support PA practices

Techniques for Area Discretization and Coverage in Aerial Photography for Precision Agriculture employing mini quad-rotors

Remote sensed imagery acquired with mini aerial vehicles, in conjunction with GIS technology enable a meticulous analysis from surveyed agricultural sites. This paper sums up the ongoing work in area discretization and coverage with mini quad-­?rotors applied to Precision Agriculture practices under the project RHEA.

Termination and cost analysis: Complexity and precision issues

The research in this thesis is related to static cost and termination analysis. Cost analysis aims at estimating the amount of resources that a given program consumes during the execution, and termination analysis aims at proving that the execution of a given program will eventually terminate. These analyses are strongly related, indeed cost analysis techniques heavily rely on techniques developed for termination analysis. Precision, scalability, and applicability are essential in static analysis in general. Precision is related to the quality of the inferred results, scalability to the size of programs that can be analyzed, and applicability to the class of programs that can be handled by the analysis (independently from precision and scalability issues). This thesis addresses these aspects in the context of cost and termination analysis, from both practical and theoretical perspectives. For cost analysis, we concentrate on the problem of solving cost relations (a form of recurrence relations) into closed-form upper and lower bounds, which is the heart of most modern cost analyzers, and also where most of the precision and applicability limitations can be found. We develop tools, and their underlying theoretical foundations, for solving cost relations that overcome the limitations of existing approaches, and demonstrate superiority in both precision and applicability. A unique feature of our techniques is the ability to smoothly handle both lower and upper bounds, by reversing the corresponding notions in the underlying theory. For termination analysis, we study the hardness of the problem of deciding termination for a speci�c form of simple loops that arise in the context of cost analysis. This study gives a better understanding of the (theoretical) limits of scalability and applicability for both termination and cost analysis.

High precision pressure sensors based on SAW devices in the GHz range

In this paper, an AlN/free-standing nanocrystalline diamond (NCD) system is proposed in order to process high frequency surface acoustic wave (SAW) resonators for sensing applications. The main problem of synthetic diamond is its high surface roughness that worsens the sputtered AlN quality and hence the device response. In order to study the feasibility of this structure, AlN films from 150 nm up to 1200 nm thick have been deposited on free-standing NCD. We have then analysed the influence of the AlN layer thickness on its crystal quality and device response. Optimized thin films of 300 nm have been used to fabricate of one-port SAW resonators operating in the 10–14 GHz frequency range. A SAW based sensor pressure with a sensibility of 0.33 MHz/bar has been fabricated.

Performance of pressure control valves and flow meters precision in operational irrigation-water balance accuracy

In pressure irrigation-water distribution networks, pressure regulating devices for controlling the discharged flow rate by irrigation units are needed due to the variability of flow rate. In addition, applied water volume is used controlled operating the valve during a calculated time interval, and assuming constant flow rate. In general, a pressure regulating valve PRV is the commonly used pressure regulating device in a hydrant, which, also, executes the open and close function. A hydrant feeds several irrigation units, requiring a wide range in flow rate. In addition, some flow meters are also available, one as a component of the hydrant and the rest are placed downstream. Every land owner has one flow meter for each group of field plots downstream the hydrant. Its lecture could be used for refining the water balance but its accuracy must be taken into account. Ideal PRV performance would maintain a constant downstream pressure. However, the true performance depends on both upstream pressure and the discharged flow rate. The objective of this work is to asses the influence of the performance on the applied volume during the whole irrigation events in a year. The results of the study have been obtained introducing the flow rate into a PRV model. Variations on flow rate are simulated by taking into account the consequences of variations on climate conditions and also decisions in irrigation operation, such us duration and frequency application. The model comprises continuity, dynamic and energy equations of the components of the PRV.

A Case Study of Geometric Modelling via 3-D Point Interpolation for the Bathymetry of the Rabasa Lakes (Alicante, Spain)

The interpolation of points by means of Information Technology programs appears as a technical tool of some relevancy in the hydrogeology in general and in the study of the humid zones in particular. Our approach has been the determination of the 3-D geometry of the humid zones of major depth of the Rabasa Lakes. To estimate the topography of the lake bed, we proceed to acquire information in the field by means of sonar and GPS equipment. A total of 335 points were measured both on the perimeter and in the lake bed. In a second stage, this information was used in a kriging program to obtain the bathymetry of the wetland. This methodology is demonstrated as one of the most reliable and cost-efficient for the 3-D analysis of this type of water masses. The bathymetric study of the zone allows us to characterize the mid- and long-term hydrological evolution of the lakes by means of depth-area-volume curves.

Routines in precision agriculture technology: an action research study

A crop management and precision agriculture software application facilitates the flow of information between disparate software/equipment and the network of individuals that work with them. A new generation of farmers are using precision technology to help them more efficiently manage their roplands. By measuring precisely the way their fields reflect and emit energy at visible and infrared wavelengths, precision farmers can monitor a wide range of variables that affect their crops,such as soil moisture, surface temperature, photosynthetic activity, and weed or pest infestations. Over thirty years have passed since Nelson and Winter put the concept of routines firmly at the center of the analysis of organizational and economic change. Taken as the central unit of analysis, routines would help understand energy and agriculture economy evolution.