Location of bioelectricity plants in the Madrid Community based on triticale crop: a multicriteria methodology

This paper presents a work whose objective is, first, to quantify the potential of the triticale biomass existing in each of the agricultural regions in the Madrid Community through a crop simulation model based on regression techniques and multiple correlation. Second, a methodology for defining which area has the best conditions for the installation of electricity plants from biomass has been described and applied. The study used a methodology based on compromise programming in a discrete multicriteria decision method (MDM) context. To make a ranking, the following criteria were taken into account: biomass potential, electric power infrastructure, road networks, protected spaces, and urban nuclei surfaces. The results indicate that, in the case of the Madrid Community, the Campiña region is the most suitable for setting up plants powered by biomass. A minimum of 17,339.9 tons of triticale will be needed to satisfy the requirements of a 2.2 MW power plant. The minimum range of action for obtaining the biomass necessary in Campiña region would be 6.6 km around the municipality of Algete, based on Geographic Information Systems. The total biomass which could be made available in considering this range in this region would be 18,430.68 t.

Cost and energy efficient reconfigurable embedded platform using Spartan-6 FPGAs

Modern FPGAs with run-time reconfiguration allow the implementation of complex systems offering both the flexibility of software-based solutions combined with the performance of hardware. This combination of characteristics, together with the development of new specific methodologies, make feasible to reach new points of the system design space, and make embedded systems built on these platforms acquire more and more importance. However, the practical exploitation of this technique in fields that traditionally have relied on resource restricted embedded systems, is mainly limited by strict power consumption requirements, the cost and the high dependence of DPR techniques with the specific features of the device technology underneath. In this work, we tackle the previously reported problems, designing a reconfigurable platform based on the low-cost and low-power consuming Spartan-6 FPGA family. The full process to develop the platform will be detailed in the paper from scratch. In addition, the implementation of the reconfiguration mechanism, including two profiles, is reported. The first profile is a low-area and low-speed reconfiguration engine based mainly on software functions running on the embedded processor, while the other one is a hardware version of the same engine, implemented in the FPGA logic. This reconfiguration hardware block has been originally designed to the Virtex-5 family, and its porting process will be also described in this work, facing the interoperability problem among different families.

Diseño de la sala 6 de Kinépolis (Madrid) con un sistema Dolby ATMOS

El objetivo de este Proyecto Fin de Carrera es el estudio y simulación de la sonorización de una sala de cine mediante la utilización del sistema DOLBY ATMOS. Para ello, se simulará la sala 6 del complejo de cines Kinépolis de Madrid utilizando el programa de simulación electroacústica EASE en el que se dispondrá el sistema de sonido DOLBY ATMOS. Primero se procederá a realizar el modelo geométrico en el programa EASE, a partir de los planos de la instalación y medidas realizadas en el recinto. Este programa de simulación permite obtener los parámetros acústicos y electroacústicos necesarios para realizar el estudio de la sala. Luego se diseñará el sistema de sonido de acuerdo a las disposiciones del sistema DOLBY ATMOS, mediante la ubicación de sistemas de altavoces de cine existentes en el mercado, siempre intentando mantener el uso de la sala de forma convencional como DOLBY DIGITAL y cumpliendo los requisitos de uniformidad y ángulos de apuntamiento recomendados por DOLBY. A continuación, una vez dispuestos los altavoces, se procederá a su configuración, realizando una ecualización y ajuste de nivel de manera individual para cada una de las fuentes sonoras, tanto de los altavoces de pantalla, altavoces de surround de pared y techo y los altavoces de subgraves. Como resultado de todo ello, se comprobarán parámetros como la inteligibilidad, respuesta impulsiva, respuesta en frecuencia y tiempo de reverberación en diferentes puntos de escucha, comparando los resultados obtenidos entre ellos. También se realizará una configuración compatible con el sistema de sonido 7.1, realizando su correspondiente configuración, ecualización, ajuste y aplicando los retardos necesarios. Una vez esté todo configurado, será dar un presupuesto de lo que supondría la reformar de un cine convencional a un sistema DOLBY ATMOS, teniendo en cuenta el número de altavoces disponibles en la sala actual, los modelos utilizados, amplificadores y mano de obra. También se realizará un diagrama de conexionado del sistema de sonido utilizado en el proyecto, incluyendo todos los parámetros necesarios de la configuración. Por último se comprobará la viabilidad técnica y económica del sistema diseñado, viendo cuál es la opción que más se adecua a cada necesidad y sugiriendo soluciones a los posibles problemas que se puedan encontrar. ABSTRACT. The main aim of this Project is the study and simulation of the sound of a movie theater by using DOLBY ATMOS system. It is going to be simulated the movie theatre 6 at Kinepolis cinema complex in Madrid using the simulation program EASE according to the sound system DOLBY ATMOS. First of all we proceed to conduct the geometric pattern in the EASE program, from installation drawings and measurements made on the premises. This simulation program allows getting the acoustic and electroacoustic parameters necessary for the study of the theatre. Then the sound system designed according to the suggestions of ATMOS DOLBY, by locating theater speaker systems on the market, always trying to keep the use of the room for DOLBY DIGITAL conventional and meeting the requirements of uniformity and pointing angles DOLBY recommended. Then, once the speakers are prepared, you can proceed to configure, make equalization and level setting individually for each of the sound sources, both screen speakers, surround speakers (wall and ceiling) and subwoofer. As a result, parameters are checked as intelligibility, impulse response, frequency response and reverberation time in different listening points, comparing the results between each other. There will also be configured to support 7.1 sound system, making the corresponding settings, equalization, level setting and applying the necessary delays. Once everything is configured, it will give an estimate of what would be the reform of a conventional film DOLBY ATMOS system, taking into account the number of speakers available in the current room, the models used, amplifiers and labor. Also there will be a wiring diagram of the sound system used in this project, including all of the configuration parameters needed. Finally, check the technical and economic feasibility of the designed system, seeing what is the option that best suits to each need and suggesting possible solutions to problems you might find during the process.

Advanced Control Strategies for a 6 DoF Hydraulic Parallel Robot Based on the Dynamic Model

Nowadays robots have made their way into real applications that were prohibitive and unthinkable thirty years ago. This is mainly due to the increase in power computations and the evolution in the theoretical field of robotics and control. Even though there is plenty of information in the current literature on this topics, it is not easy to find clear concepts of how to proceed in order to design and implement a controller for a robot. In general, the design of a controller requires of a complete understanding and knowledge of the system to be controlled. Therefore, for advanced control techniques the systems must be first identified. Once again this particular objective is cumbersome and is never straight forward requiring of great expertise and some criteria must be adopted. On the other hand, the particular problem of designing a controller is even more complex when dealing with Parallel Manipulators (PM), since their closed-loop structures give rise to a highly nonlinear system. Under this basis the current work is developed, which intends to resume and gather all the concepts and experiences involve for the control of an Hydraulic Parallel Manipulator. The main objective of this thesis is to provide a guide remarking all the steps involve in the designing of advanced control technique for PMs. The analysis of the PM under study is minced up to the core of the mechanism: the hydraulic actuators. The actuators are modeled and experimental identified. Additionally, some consideration regarding traditional PID controllers are presented and an adaptive controller is finally implemented. From a macro perspective the kinematic and dynamic model of the PM are presented. Based on the model of the system and extending the adaptive controller of the actuator, a control strategy for the PM is developed and its performance is analyzed with simulation.