Service needs forecasting: an approach for the automotive industry using analogies with medical ER management models.

During the past years, the industry has shifted position and moved towards “the luxury universe” whose customers are demanding, treating individuals as unique and valued customer for the business, offering vehicles produced with the state of the art technologies and implementing the highest finishing standards. Due to the competitive level in the market, car makers enable processes which equalizes customer services to E.R. management, being dealt with the maximum urgency that allows the comparison between both, car workshops and emergency rooms, where workshop bays or ramps will be equal to emergency boxes and skilled technicians are equivalent to the health care specialist, who will carry out tests and checks prior to afford any final operation, keeping the “patient” under control before it is back to normal utilization. This paper establishes a valid model for the automotive industry to estimate customer service demand forecasting under variable demand conditions using analogies with patient demand models used for the medical ER.

Desintegración vertical en la industria del automóvil en España: un caso de estudio = Vertical disintegration in the automotive industry in Spain: a case study

En los años recientes se ha producido un rápido crecimiento del comercio internacional en productos semielaborados que son diseñados, producidos y ensamblados en diferentes localizaciones a lo largo de diferentes países, debido principalmente a los siguientes motivos: el desarrollo de las tecnologías de la información, la reducción de los costes de transporte, la liberalización de los mercados de capitales, la armonización de factores institucionales, la integración económica regional que implica la reducción y la eliminación de las barreras al comercio, el desarrollo económico de los países emergentes, el uso de economías de escala, así como una desregulación del comercio internacional. Todo ello ha incrementado la competencia a nivel mundial en los mercados y ha posibilitado a las compañías tener más facilidad de acceso a potenciales mercados, así como a la adquisición de capacidades y conocimientos en otros países y a la realización de alianzas estratégicas internacionales con terceros, creando un entorno con mayor incertidumbre y más exigente para las compañías que componen una industria, y que tiene consecuencias directas en las operaciones de las compañías y en la organización de su producción. Las compañías, para adaptarse, ser competitivas y beneficiarse de este nuevo escenario globalizado y más competitivo, han externalizado partes del proceso productivo hacia proveedores especializados, creando un nuevo mercado intermedio que divide el proceso productivo, anteriormente integrado en las compañías que conforman una industria, entre dos conjuntos de empresas especializadas en esa industria. Dicho proceso suele ocurrir conservando la industria en que tiene lugar, los mismos servicios y productos, la tecnología empleada y las compañías originales que la conformaban previamente a la desintegración vertical. Todo ello es así debido a que es beneficioso tanto para las compañías originales de la industria como para las nuevas compañías de este mercado intermedio por diversos motivos. La desintegración vertical en una industria tiene unas consecuencias que la transforman completamente, así como la forma de operar de las compañías que la integran, incluso para aquellas que permanecen verticalmente integradas. Una de las características más importantes de esta desintegración vertical en una industria es la posibilidad que tiene una compañía de adquirir a una tercera la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por la compañía adquiriente con la práctica del outsourcing; así mismo, una compañía puede realizar la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por una tercera compañía con la práctica de la fragmentación. El principal objetivo de la presente investigación es el estudio de los motivos, los facilitadores, los efectos, las consecuencias y los principales factores significativos, microeconómicos y macroeconómicos, que desencadenan o incrementan la práctica de la desintegración vertical en una industria; para ello, la investigación se divide en dos líneas completamente diferenciadas: el estudio de la práctica del outsourcing y, por otro lado, el estudio de la fragmentación por parte de las compañías que componen la industria del automóvil en España, puesto que se trata de una de las industrias más desintegradas verticalmente y fragmentadas, y este sector posee una gran importancia en la economía del país. En primer lugar, se hace una revisión de la literatura existente relativa a los siguientes aspectos: desintegración vertical, outsourcing, fragmentación, teoría del comercio internacional, historia de la industria del automóvil en España y el uso de las aglomeraciones geográficas y las tecnologías de la información en el sector del automóvil. La metodología empleada en cada uno de ellos ha sido diferente en función de la disponibilidad de los datos y del enfoque de investigación: los factores microeconómicos, utilizando el outsourcing, y los factores macroeconómicos, empleando la fragmentación. En el estudio del outsourcing, se usa un índice basado en las compras externas sobre el valor total de la producción. Así mismo, se estudia su correlación y significación con las variables económicas más importantes que definen a una compañía del sector del automóvil, utilizando la técnica estadística de regresión lineal. Aquellas variables relacionadas con la competencia en el mercado, la externalización de las actividades de menor valor añadido y el incremento de la modularización de las actividades de la cadena de valor, han resultado significativas con la práctica del outsourcing. En el estudio de la fragmentación se seleccionan un conjunto de factores macroeconómicos, comúnmente usados en este tipo de investigaciones, relacionados con las principales magnitudes económicas de un país, y un conjunto de factores macroeconómicos, no comúnmente usados en este tipo de investigaciones, relacionados con la libertad económica y el comercio internacional de un país. Se emplea un modelo de regresión logística para identificar qué factores son significativos en la práctica de la fragmentación. De entre todos los factores usados en el modelo, los relacionados con las economías de escala y los costes de servicio han resultado significativos. Los resultados obtenidos de los test estadísticos realizados en el modelo de regresión logística han resultado satisfactorios; por ello, el modelo propuesto de regresión logística puede ser considerado sólido, fiable y versátil; además, acorde con la realidad. De los resultados obtenidos en el estudio del outsourcing y de la fragmentación, combinados conjuntamente con el estado del arte, se concluye que el principal factor que desencadena la desintegración vertical en la industria del automóvil es la competencia en el mercado de vehículos. Cuanto mayor es la demanda de vehículos, más se reducen los beneficios y la rentabilidad para sus fabricantes. Estos, para ser competitivos, diferencian sus productos de la competencia centrándose en las actividades que mayor valor añadido aportan al producto final, externalizando las actividades de menor valor añadido a proveedores especializados, e incrementando la modularidad de las actividades de la cadena de valor. Las compañías de la industria del automóvil se especializan en alguna o varias de estas actividades modularizadas que, combinadas con el uso de factores facilitadores como las economías de escala, las tecnologías de la información, las ventajas de la globalización económica y la aglomeración geográfica de una industria, incrementan y motivan la desintegración vertical en la industria del automóvil, desencadenando la coespecialización en dos sectores claramente diferenciados: el sector de fabricantes de vehículos y el sector de proveedores especializados. Cada uno de ellos se especializa en unas actividades y en unos productos o servicios específicos de la cadena de valor, lo cual genera las siguientes consecuencias en la industria del automóvil: se reducen los costes de transacción en los productos o servicios intercambiados; se incrementan la relación de dependencia entre fabricantes de vehículos y proveedores especializados, provocando un aumento en la cooperación y la coordinación, acelerando el proceso de aprendizaje, posibilitando a ambos adquirir nuevas capacidades, conocimientos y recursos, y creando nuevas ventajas competitivas para ambos; por último, las barreras de entrada a la industria del automóvil y el número de compañías se ven alteradas cambiando su estructura. Como futura línea de investigación, los fabricantes de vehículos tenderán a centrarse en investigar, diseñar y comercializar el producto o servicio, delegando el ensamblaje en manos de nuevos especialistas en la materia, el contract manufacturer; por ello, sería conveniente investigar qué factores motivantes o facilitadores existen y qué consecuencias tendría la implantación de los contract manufacturer en la industria del automóvil. 1.1. ABSTRACT In recent years there has been a rapid growth of international trade in semi-finished products designed, produced and assembled in different locations across different countries, mainly due to the following reasons: development of information technologies, reduction of transportation costs, liberalisation of capital markets, harmonisation of institutional factors, regional economic integration, which involves the reduction and elimination of trade barriers, economic development of emerging countries, use of economies of scale and deregulation of international trade. All these factors have increased competition in markets at a global level and have allowed companies to gain easier access to potential markets and to the acquisition of skills and knowledge in other countries, as well as to the completion of international strategic alliances with third parties, thus creating a more demanding and uncertain environment for these companies constituting an industry, which has a direct impact on the companies' operations and the organization of their production. In order to adapt, be competitive and benefit from this new and more competitive global scenario, companies have outsourced some parts of their production process to specialist suppliers, generating a new intermediate market which divides the production process, previously integrated in the companies that made up the industry, into two sets of companies specialized in that industry. This process often occurs while preserving the industry where it takes place, its same services and products, the technology used and the original companies that formed it prior to vertical disintegration. This is because it is beneficial for both the industry's original companies and the companies belonging to this new intermediate market, for various reasons. Vertical disintegration has consequences which completely transform the industry where it takes place as well as the modus operandi of the companies that are part of it, even of those who remain vertically integrated. One of the most important features of vertical disintegration of an industry is the possibility for a company to acquire from a third one the first part of the production process or a semi-finished product, which will then be finished by the acquiring company through the practice of outsourcing; also, a company can perform the first part of the production process or a semi-finish product, which will then be completed by a third company through the practice of fragmentation. The main objective of this research is to study the motives, facilitators, effects, consequences and major significant microeconomic and macroeconomic factors that trigger or increase the practice of vertical disintegration in a certain industry; in order to do so, research is divided into two completely differentiated lines: on the one hand, the study of the practise of outsourcing and, on the other, the study of fragmentation by companies constituting the automotive industry in Spain, since this is one of the most vertically disintegrated and fragmented industries and this particular sector is of major significance in this country's economy. First, a review is made of the existing literature, on the following aspects: vertical disintegration, outsourcing, fragmentation, international trade theory, history of the automobile industry in Spain and the use of geographical agglomeration and information technologies in the automotive sector. The methodology used for each of these aspects has been different depending on the availability of data and the research approach: the microeconomic factors, using outsourcing, and the macroeconomic factors, using fragmentation. In the study on outsourcing, an index is used based on external purchases in relation to the total value of production. Likewise, their significance and correlation with the major economic variables that define an automotive company are studied, using the statistical technique of linear regression. Variables related to market competition, outsourcing of lowest value-added activities and increased modularisation of the activities of the value chain have turned out to be significant with the practice of outsourcing. In the study of fragmentation, a set of macroeconomic factors commonly used for this type of research, is selected, related to the main economic indicators of a country, as well as a set of macroeconomic factors, not commonly used for this type of research, which are related to economic freedom and the international trade of a certain country. A logistic regression model is used to identify which factors are significant in the practice of fragmentation. Amongst all factors used in the model, those related to economies of scale and service costs have turned out to be significant. The results obtained from the statistical tests performed on the logistic regression model have been successful; hence, the suggested logistic regression model can be considered to be solid, reliable and versatile; likewise, it is in line with reality. From the results obtained in the study of outsourcing and fragmentation, combined with the state of the art, it is concluded that the main factor that triggers vertical disintegration in the automotive industry is competition within the vehicle market. The greater the vehicle demand, the lower the earnings and profitability for manufacturers. These, in order to be competitive, differentiate their products from the competition by focusing on those activities that contribute with the highest added value to the final product, outsourcing the lower valueadded activities to specialist suppliers, and increasing the modularity of the activities of the value chain. Companies in the automotive industry specialize in one or more of these modularised activities which, combined with the use of enabling factors such as economies of scale, information technologies, the advantages of economic globalisation and the geographical agglomeration of an industry, increase and encourage vertical disintegration in the automotive industry, triggering co-specialization in two clearly distinct sectors: the sector of vehicle manufacturers and the specialist suppliers sector. Each of them specializes in certain activities and specific products or services of the value chain, generating the following consequences in the automotive industry: reduction of transaction costs of the goods or services exchanged; growth of the relationship of dependency between vehicle manufacturers and specialist suppliers, which causes an increase in cooperation and coordination, accelerates the learning process, enables both to acquire new skills, knowledge and resources, and creates new competitive advantages for both; finally, barriers to entry the automotive industry and the number of companies are altered, changing their structure. As a future line of research, vehicle manufacturers will tend to focus on researching, designing and marketing the product or service, delegating the assembly in the hands of new specialists in the field, the contract manufacturer; for this reason, it would be useful to investigate what motivating or facilitating factors exist in this respect and what consequences would the implementation of contract manufacturers have in the automotive industry.

Comparing fuzzy and intelligent PI controllers in stop-and-go manoeuvres

The aim of this work was twofold: on the one hand, to describe a comparative study of two intelligent control techniques-fuzzy and intelligent proportional-integral (PI) control, and on the other, to try to provide an answer to an as yet unsolved topic in the automotive sector-stop-and-go control in urban environments at very low speeds. Commercial vehicles exhibit nonlinear behavior and therefore constitute an excellent platform on which to check the controllers. This paper describes the design, tuning, and evaluation of the controllers performing actions on the longitudinal control of a car-the throttle and brake pedals-to accomplish stop-and-go manoeuvres. They are tested in two steps. First, a simulation model is used to design and tune the controllers, and second, these controllers are implemented in the commercial vehicle-which has automatic driving capabilities-to check their behavior. A stop-and-go manoeuvre is implemented with the two control techniques using two cooperating vehicles.

Low-speed longitudinal controllers for mass-produced cars: A comparative study

Four longitudinal control techniques are compared: a classical Proportional-Integral (PI) control; an advanced technique-called the i-PI-that adds an intelligent component to the PI; a fuzzy controller based on human experience; and an adaptive-network-based fuzzy inference system. The controllers were designed to tackle one of the challenging topics as yet unsolved by the automotive sector: managing autonomously a gasoline-propelled vehicle at very low speeds. The dynamics involved are highly nonlinear and constitute an excellent test-bed for newly designed controllers. A Citroën C3 Pluriel car was modified to permit autonomous action on the accelerator and the brake pedals-i.e., longitudinal control. The controllers were tested in two stages. First, the vehicle was modeled to check the controllers' feasibility. Second, the controllers were then implemented in the Citroën, and their behavior under the same conditions on an identical real circuit was compared.

Discriminación del estado de la carretera mediante procesado acústico en vehículo

La rápida adopción de dispositivos electrónicos en el automóvil, ha contribuido a mejorar en gran medida la seguridad y el confort. Desde principios del siglo 20, la investigación en sistemas de seguridad activa ha originado el desarrollo de tecnologías como ABS (Antilock Brake System), TCS (Traction Control System) y ESP (Electronic Stability Program). El coste de despliegue de estos sistemas es crítico: históricamente, sólo han sido ampliamente adoptados cuando el precio de los sensores y la electrónica necesarios para su construcción ha caído hasta un valor marginal. Hoy en día, los vehículos a motor incluyen un amplio rango de sensores para implementar las funciones de seguridad. La incorporación de sistemas que detecten la presencia de agua, hielo o nieve en la vía es un factor adicional que podría ayudar a evitar situaciones de riesgo. Existen algunas implementaciones prácticas capaces de detectar carreteras mojadas, heladas y nevadas, aunque con limitaciones importantes. En esta tesis doctoral, se propone una aproximación novedosa al problema, basada en el análisis del ruido de rodadura generado durante la conducción. El ruido de rodadura es capturado y preprocesado. Después es analizado utilizando un clasificador basado en máquinas de vectores soporte (SVM), con el fin de generar una estimación del estado del firme. Todas estas operaciones se realizan en el propio vehículo. El sistema propuesto se ha desarrollado y evaluado utilizando Matlabr, mostrando tasas de aciertos de más del 90%. Se ha realizado una implementación en tiempo real, utilizando un prototipo basado en DSP. Después se han introducido varias optimizaciones para permitir que el sistema sea realizable usando un microcontrolador de propósito general. Finalmente se ha realizado una implementación hardware basada en un microcontrolador, integrándola estrechamente con las ECU del vehículo, pudiendo obtener datos capturados por los sensores del mismo y enviar las estimaciones del estado del firme. El sistema resultante ha sido patentado, y destaca por su elevada tasa de aciertos con un tamaño, consumo y coste reducidos. ABSTRACT Proliferation of automotive electronics, has greatly improved driving safety and comfort. Since the beginning of the 20th century, investigation in active safety systems has resulted in the development of technologies such as ABS (Antilock Brake System), TCS (Traction Control System) and ESP (Electronic Stability Program). Deployment cost of these systems is critical: historically, they have been widely adopted only when the price of the sensors and electronics needed to build them has been cut to a marginal value. Nowadays, motor vehicles include a wide range of sensors to implement the safety functions. Incorporation of systems capable of detecting water, ice or snow on the road is an additional factor that could help avoiding risky situations. There are some implementations capable of detecting wet, icy and snowy roads, although with important limitations. In this PhD Thesis, a novel approach is proposed, based on the analysis of the tyre/road noise radiated during driving. Tyre/road noise is captured and pre-processed. Then it is analysed using a Support Vector Machine (SVM) based classifier, to output an estimation of the road status. All these operations are performed on-board. Proposed system is developed and evaluated using Matlabr, showing success rates greater than 90%. A real time implementation is carried out using a DSP based prototype. Several optimizations are introduced enabling the system to work using a low-cost general purpose microcontroller. Finally a microcontroller based hardware implementation is developed. This implementation is tightly integrated with the vehicle ECUs, allowing it to obtain data captured by its sensors, and to send the road status estimations. Resulting system has been patented, and is notable because of its high hit rate, small size, low power consumption and low cost.

Co-simulation Methodologies for Hybrid and Electric Vehicle Dynamics

In recent decades, full electric and hybrid electric vehicles have emerged as an alternative to conventional cars due to a range of factors, including environmental and economic aspects. These vehicles are the result of considerable efforts to seek ways of reducing the use of fossil fuel for vehicle propulsion. Sophisticated technologies such as hybrid and electric powertrains require careful study and optimization. Mathematical models play a key role at this point. Currently, many advanced mathematical analysis tools, as well as computer applications have been built for vehicle simulation purposes. Given the great interest of hybrid and electric powertrains, along with the increasing importance of reliable computer-based models, the author decided to integrate both aspects in the research purpose of this work. Furthermore, this is one of the first final degree projects held at the ETSII (Higher Technical School of Industrial Engineers) that covers the study of hybrid and electric propulsion systems. The present project is based on MBS3D 2.0, a specialized software for the dynamic simulation of multibody systems developed at the UPM Institute of Automobile Research (INSIA). Automobiles are a clear example of complex multibody systems, which are present in nearly every field of engineering. The work presented here benefits from the availability of MBS3D software. This program has proven to be a very efficient tool, with a highly developed underlying mathematical formulation. On this basis, the focus of this project is the extension of MBS3D features in order to be able to perform dynamic simulations of hybrid and electric vehicle models. This requires the joint simulation of the mechanical model of the vehicle, together with the model of the hybrid or electric powertrain. These sub-models belong to completely different physical domains. In fact the powertrain consists of energy storage systems, electrical machines and power electronics, connected to purely mechanical components (wheels, suspension, transmission, clutch…). The challenge today is to create a global vehicle model that is valid for computer simulation. Therefore, the main goal of this project is to apply co-simulation methodologies to a comprehensive model of an electric vehicle, where sub-models from different areas of engineering are coupled. The created electric vehicle (EV) model consists of a separately excited DC electric motor, a Li-ion battery pack, a DC/DC chopper converter and a multibody vehicle model. Co-simulation techniques allow car designers to simulate complex vehicle architectures and behaviors, which are usually difficult to implement in a real environment due to safety and/or economic reasons. In addition, multi-domain computational models help to detect the effects of different driving patterns and parameters and improve the models in a fast and effective way. Automotive designers can greatly benefit from a multidisciplinary approach of new hybrid and electric vehicles. In this case, the global electric vehicle model includes an electrical subsystem and a mechanical subsystem. The electrical subsystem consists of three basic components: electric motor, battery pack and power converter. A modular representation is used for building the dynamic model of the vehicle drivetrain. This means that every component of the drivetrain (submodule) is modeled separately and has its own general dynamic model, with clearly defined inputs and outputs. Then, all the particular submodules are assembled according to the drivetrain configuration and, in this way, the power flow across the components is completely determined. Dynamic models of electrical components are often based on equivalent circuits, where Kirchhoff’s voltage and current laws are applied to draw the algebraic and differential equations. Here, Randles circuit is used for dynamic modeling of the battery and the electric motor is modeled through the analysis of the equivalent circuit of a separately excited DC motor, where the power converter is included. The mechanical subsystem is defined by MBS3D equations. These equations consider the position, velocity and acceleration of all the bodies comprising the vehicle multibody system. MBS3D 2.0 is entirely written in MATLAB and the structure of the program has been thoroughly studied and understood by the author. MBS3D software is adapted according to the requirements of the applied co-simulation method. Some of the core functions are modified, such as integrator and graphics, and several auxiliary functions are added in order to compute the mathematical model of the electrical components. By coupling and co-simulating both subsystems, it is possible to evaluate the dynamic interaction among all the components of the drivetrain. ‘Tight-coupling’ method is used to cosimulate the sub-models. This approach integrates all subsystems simultaneously and the results of the integration are exchanged by function-call. This means that the integration is done jointly for the mechanical and the electrical subsystem, under a single integrator and then, the speed of integration is determined by the slower subsystem. Simulations are then used to show the performance of the developed EV model. However, this project focuses more on the validation of the computational and mathematical tool for electric and hybrid vehicle simulation. For this purpose, a detailed study and comparison of different integrators within the MATLAB environment is done. Consequently, the main efforts are directed towards the implementation of co-simulation techniques in MBS3D software. In this regard, it is not intended to create an extremely precise EV model in terms of real vehicle performance, although an acceptable level of accuracy is achieved. The gap between the EV model and the real system is filled, in a way, by introducing the gas and brake pedals input, which reflects the actual driver behavior. This input is included directly in the differential equations of the model, and determines the amount of current provided to the electric motor. For a separately excited DC motor, the rotor current is proportional to the traction torque delivered to the car wheels. Therefore, as it occurs in the case of real vehicle models, the propulsion torque in the mathematical model is controlled through acceleration and brake pedal commands. The designed transmission system also includes a reduction gear that adapts the torque coming for the motor drive and transfers it. The main contribution of this project is, therefore, the implementation of a new calculation path for the wheel torques, based on performance characteristics and outputs of the electric powertrain model. Originally, the wheel traction and braking torques were input to MBS3D through a vector directly computed by the user in a MATLAB script. Now, they are calculated as a function of the motor current which, in turn, depends on the current provided by the battery pack across the DC/DC chopper converter. The motor and battery currents and voltages are the solutions of the electrical ODE (Ordinary Differential Equation) system coupled to the multibody system. Simultaneously, the outputs of MBS3D model are the position, velocity and acceleration of the vehicle at all times. The motor shaft speed is computed from the output vehicle speed considering the wheel radius, the gear reduction ratio and the transmission efficiency. This motor shaft speed, somehow available from MBS3D model, is then introduced in the differential equations corresponding to the electrical subsystem. In this way, MBS3D and the electrical powertrain model are interconnected and both subsystems exchange values resulting as expected with tight-coupling approach.When programming mathematical models of complex systems, code optimization is a key step in the process. A way to improve the overall performance of the integration, making use of C/C++ as an alternative programming language, is described and implemented. Although this entails a higher computational burden, it leads to important advantages regarding cosimulation speed and stability. In order to do this, it is necessary to integrate MATLAB with another integrated development environment (IDE), where C/C++ code can be generated and executed. In this project, C/C++ files are programmed in Microsoft Visual Studio and the interface between both IDEs is created by building C/C++ MEX file functions. These programs contain functions or subroutines that can be dynamically linked and executed from MATLAB. This process achieves reductions in simulation time up to two orders of magnitude. The tests performed with different integrators, also reveal the stiff character of the differential equations corresponding to the electrical subsystem, and allow the improvement of the cosimulation process. When varying the parameters of the integration and/or the initial conditions of the problem, the solutions of the system of equations show better dynamic response and stability, depending on the integrator used. Several integrators, with variable and non-variable step-size, and for stiff and non-stiff problems are applied to the coupled ODE system. Then, the results are analyzed, compared and discussed. From all the above, the project can be divided into four main parts: 1. Creation of the equation-based electric vehicle model; 2. Programming, simulation and adjustment of the electric vehicle model; 3. Application of co-simulation methodologies to MBS3D and the electric powertrain subsystem; and 4. Code optimization and study of different integrators. Additionally, in order to deeply understand the context of the project, the first chapters include an introduction to basic vehicle dynamics, current classification of hybrid and electric vehicles and an explanation of the involved technologies such as brake energy regeneration, electric and non-electric propulsion systems for EVs and HEVs (hybrid electric vehicles) and their control strategies. Later, the problem of dynamic modeling of hybrid and electric vehicles is discussed. The integrated development environment and the simulation tool are also briefly described. The core chapters include an explanation of the major co-simulation methodologies and how they have been programmed and applied to the electric powertrain model together with the multibody system dynamic model. Finally, the last chapters summarize the main results and conclusions of the project and propose further research topics. In conclusion, co-simulation methodologies are applicable within the integrated development environments MATLAB and Visual Studio, and the simulation tool MBS3D 2.0, where equation-based models of multidisciplinary subsystems, consisting of mechanical and electrical components, are coupled and integrated in a very efficient way.