Formation energy of vacancies in FeCr alloys: Dependence on Cr concentration

A modified version of the concentration-dependent model (CDM) potential (A. Caro et al., Phys. Rev. Lett. 95 (2005) 075702) [1] has been developed to study defects in Fe–Cr for different Crconcentrations. A comparison between this new potential and DFT results for a variety of point defect configurations is performed in order to test its reliability for radiation damage studies. The effect of Crconcentration on the vacancyformationenergy in Fe–Cr alloys is analyzed in detail. This study shows a linear dependence of the vacancyformationenergy on Crconcentration for values above 6% of Cr. However, the formationenergy deviates from the linear interpolation in the region below 6% Crconcentration. In order to understand this behavior, the influence of the relative positions between Cr atoms and vacant sites on the vacancyformationenergy has been studied.

Object Kinetic Monte Carlo calculations of irradiated Fe-Cr dilute alloys: The effect of the interaction radius between substitutional Cr and self-interstitial Fe

ObjectKineticMonteCarlo models allow for the study of the evolution of the damage created by irradiation to time scales that are comparable to those achieved experimentally. Therefore, the essential ObjectKineticMonteCarlo parameters can be validated through comparison with experiments. However, this validation is not trivial since a large number of parameters is necessary, including migration energies of point defects and their clusters, binding energies of point defects in clusters, as well as the interactionradii. This is particularly cumbersome when describing an alloy, such as the Fe–Cr system, which is of interest for fusion energy applications. In this work we describe an ObjectKineticMonteCarlo model for Fe–Cr alloys in the dilute limit. The parameters used in the model come either from density functional theory calculations or from empirical interatomic potentials. This model is used to reproduce isochronal resistivity recovery experiments of electron irradiateddiluteFe–Cr alloys performed by Abe and Kuramoto. The comparison between the calculated results and the experiments reveal that an important parameter is the capture radius between substitutionalCr and self-interstitialFe atoms. A parametric study is presented on the effect of the capture radius on the simulated recovery curves.

High-temperature mechanical properties of aluminium alloys reinforced with titanium diboride (TiB2) particles

The physical and mechanical properties of metal matrix composites were improved by the addition of reinforcements. The mechanical properties of particulate-reinforced metal-matrix composites based on aluminium alloys (6061 and 7015) at high temperatures were studied. Titanium diboride (TiB2) particles were used as the reinforcement. All the composites were produced by hot extrusion. The tensile properties and fracture characteristics of these materials were investigated at room temperature and at high temperatures to determine their ultimate strength and strain to failure. The fracture surface was analysed by scanning electron microscopy. TiB2 particles provide high stability of the aluminium alloys (6061 and 7015) in the fabrication process. An improvement in the mechanical behaviour was achieved by adding TiB2 particles as reinforcement in both the aluminium alloys. Adding TiB2 particles reduces the ductility of the aluminium alloys but does not change the microscopic mode of failure, and the fracture surface exhibits a ductile appearance with dimples formed by coalescence.

Interstitial defects stability in FeCr alloys vs Cr concentration

Finding adequate materials to withstand the demanding conditions in the future fusion and fission reactors is a real challenge in the development of these technologies. Structural materials need to sustain high irradiation doses and temperatures that will change the microstructure over time. A better understanding of the changes produced by the irradiation will allow for a better choice of materials, ensuring a safer and reliable future power plants. High-Cr ferritic/martensitic steels head the list of structural materials due to their high resistance to swelling and corrosion. However, it is well known that these alloys present a problem of embrittlement, which could be caused by the presence of defects created by irradiation as these defects act as obstacles for dislocation motion. Therefore, the mechanical response of these materials will depend on the type of defects created during irradiation. In this work, we address a study of the effect Cr concentration has on single interstitial defect formation energies in FeCr alloys.

Mechanical properties of tungsten alloys with Y2O3 and titanium additions

In this research the mechanical behaviour of pure tungsten (W) and its alloys (2 wt.% Ti–0.47 wt.% Y2O3 and 4 wt.% Ti–0.5 wt.% Y2O3) is compared. These tungsten alloys, have been obtained by powder metallurgy. The yield strength, fracture toughness and elastic modulus have been studied in the temperature interval of 25 °C to 1000 °C. The results have shown that the addition of Ti substantially improves the bending strength and toughness of W, but it also dramatically increases the DBTT. On the other hand, the addition of 0.5% Y2O3, is enough to improve noticeably the oxidation behaviour at the higher temperatures. The grain size, fractography and microstructure are studied in these materials. Titanium is a good grain growth inhibitor and effective precursor of liquid phase in HIP. The simultaneous presence of Y2O3 and Ti permits to obtain materials with low pores presence

Service needs forecasting: an approach for the automotive industry using analogies with medical ER management models.

During the past years, the industry has shifted position and moved towards “the luxury universe” whose customers are demanding, treating individuals as unique and valued customer for the business, offering vehicles produced with the state of the art technologies and implementing the highest finishing standards. Due to the competitive level in the market, car makers enable processes which equalizes customer services to E.R. management, being dealt with the maximum urgency that allows the comparison between both, car workshops and emergency rooms, where workshop bays or ramps will be equal to emergency boxes and skilled technicians are equivalent to the health care specialist, who will carry out tests and checks prior to afford any final operation, keeping the “patient” under control before it is back to normal utilization. This paper establishes a valid model for the automotive industry to estimate customer service demand forecasting under variable demand conditions using analogies with patient demand models used for the medical ER.

Intensive use of aluminium in car body construction

The developments in materials over the last decade have been considerable within the automotive industry, being one of the leaders in innovative product applications. Sustainable product development of an automotive structure requires a balanced approach towards technological, economical and ecological aspects. The introduction of new materials and processes is dependent on satisfying different factors. Competitive and legislative pressures, creating the need for change, affect these factors considerably. The process, direction and speed of change are often reactive. Current paper shows the application of aluminium alloys, for the use in the bottom structure of a car to face the problem for the weight of the entire bottom structure under static load conditions, including stiffness, strength and buckling constraints. In addition to minimized mass and materials' price, the assessment of an environmental impact of materials-candidates during the entire life cycle of the structure is considered.

Influence of the Lubrication Conditions on the Surface Finish of Turned Aeronautical Aluminium Alloys. A preliminary Study

Nowadays, one of the main objectives that affects the development of any new product is the respect for the environment. Until the late 80's, the development and manufacture of the most of the product were aimed to achieve maximum quality in time and costs with environmental issues relegated to secondary importance. On the other hand, in the 90's, the pressure from factors such as markets, financial and legislative factors, led to environmental considerations being taken into account. In this context, the current aeronautical industry strategies are based on the search for economic, environmental and energy efficiency considerations for all the processes involved in the aircraft manufacturing.

Laser Shock Processing: An Emerging Technique for the Enhancement of Surface Properties and Fatigue Life of High Strength Metal Alloys

Profiting by the increasing availability of laser sources delivering intensities above 10 9 W/cm 2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically steels and Al and Ti alloys) under different LSP irradiation conditions are presented

Flow and fracture behaviour of high performance alloys

Based on our needs, that is to say, through precise simulation of the impact phenomena that may occur inside a jet engine turbine with an explicit non-linear finite element code, four new material models are postulated. Each one of is calibrated for four high-performance alloys that can be encountered in a modern jet engine. A new uncoupled material model for high strain and ballistic is proposed. Based on a Johnson-Cook type model, the proposed formulation introduces the effect of the third deviatoric invariant by means of three different Lode angle dependent functions. The Lode dependent functions are added to both plasticity and failure models. The postulated model is calibrated for a 6061-T651 aluminium alloy with data taken from the literature. The fracture pattern predictability of the JCX material model is shown performing numerical simulations of various quasi-static and dynamic tests. As an extension of the above-mentioned model, a modification in the thermal softening behaviour due to phase transformation temperatures is developed (JCXt). Additionally, a Lode angle dependent flow stress is defined. Analysing the phase diagram and high temperature tests performed, phase transformation temperatures of the FV535 stainless steel are determined. The postulated material model constants for the FV535 stainless steel are calibrated. A coupled elastoplastic-damage material model for high strain and ballistic applications is presented (JCXd). A Lode angle dependent function is added to the equivalent plastic strain to failure definition of the Johnson-Cook failure criterion. The weakening in the elastic law and in the Johnson-Cook type constitutive relation implicitly introduces the Lode angle dependency in the elastoplastic behaviour. The material model is calibrated for precipitation hardened Inconel 718 nickel-base superalloy. The combination of a Lode angle dependent failure criterion with weakened constitutive equations is proven to predict fracture patterns of the mechanical tests performed and provide reliable results. A transversely isotropic material model for directionally solidified alloys is presented. The proposed yield function is based a single linear transformation of the stress tensor. The linear operator weighs the degree of anisotropy of the yield function. The elastic behaviour, as well as the hardening, are considered isotropic. To model the hardening, a Johnson-Cook type relation is adopted. A material vector is included in the model implementation. The failure is modelled with the Cockroft-Latham failure criterion. The material vector allows orienting the reference orientation in any other that the user may need. The model is calibrated for the MAR-M 247 directionally solidified nickel-base superalloy.

Desintegración vertical en la industria del automóvil en España: un caso de estudio = Vertical disintegration in the automotive industry in Spain: a case study

En los años recientes se ha producido un rápido crecimiento del comercio internacional en productos semielaborados que son diseñados, producidos y ensamblados en diferentes localizaciones a lo largo de diferentes países, debido principalmente a los siguientes motivos: el desarrollo de las tecnologías de la información, la reducción de los costes de transporte, la liberalización de los mercados de capitales, la armonización de factores institucionales, la integración económica regional que implica la reducción y la eliminación de las barreras al comercio, el desarrollo económico de los países emergentes, el uso de economías de escala, así como una desregulación del comercio internacional. Todo ello ha incrementado la competencia a nivel mundial en los mercados y ha posibilitado a las compañías tener más facilidad de acceso a potenciales mercados, así como a la adquisición de capacidades y conocimientos en otros países y a la realización de alianzas estratégicas internacionales con terceros, creando un entorno con mayor incertidumbre y más exigente para las compañías que componen una industria, y que tiene consecuencias directas en las operaciones de las compañías y en la organización de su producción. Las compañías, para adaptarse, ser competitivas y beneficiarse de este nuevo escenario globalizado y más competitivo, han externalizado partes del proceso productivo hacia proveedores especializados, creando un nuevo mercado intermedio que divide el proceso productivo, anteriormente integrado en las compañías que conforman una industria, entre dos conjuntos de empresas especializadas en esa industria. Dicho proceso suele ocurrir conservando la industria en que tiene lugar, los mismos servicios y productos, la tecnología empleada y las compañías originales que la conformaban previamente a la desintegración vertical. Todo ello es así debido a que es beneficioso tanto para las compañías originales de la industria como para las nuevas compañías de este mercado intermedio por diversos motivos. La desintegración vertical en una industria tiene unas consecuencias que la transforman completamente, así como la forma de operar de las compañías que la integran, incluso para aquellas que permanecen verticalmente integradas. Una de las características más importantes de esta desintegración vertical en una industria es la posibilidad que tiene una compañía de adquirir a una tercera la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por la compañía adquiriente con la práctica del outsourcing; así mismo, una compañía puede realizar la primera parte del proceso productivo o un bien semielaborado, que posteriormente será finalizado por una tercera compañía con la práctica de la fragmentación. El principal objetivo de la presente investigación es el estudio de los motivos, los facilitadores, los efectos, las consecuencias y los principales factores significativos, microeconómicos y macroeconómicos, que desencadenan o incrementan la práctica de la desintegración vertical en una industria; para ello, la investigación se divide en dos líneas completamente diferenciadas: el estudio de la práctica del outsourcing y, por otro lado, el estudio de la fragmentación por parte de las compañías que componen la industria del automóvil en España, puesto que se trata de una de las industrias más desintegradas verticalmente y fragmentadas, y este sector posee una gran importancia en la economía del país. En primer lugar, se hace una revisión de la literatura existente relativa a los siguientes aspectos: desintegración vertical, outsourcing, fragmentación, teoría del comercio internacional, historia de la industria del automóvil en España y el uso de las aglomeraciones geográficas y las tecnologías de la información en el sector del automóvil. La metodología empleada en cada uno de ellos ha sido diferente en función de la disponibilidad de los datos y del enfoque de investigación: los factores microeconómicos, utilizando el outsourcing, y los factores macroeconómicos, empleando la fragmentación. En el estudio del outsourcing, se usa un índice basado en las compras externas sobre el valor total de la producción. Así mismo, se estudia su correlación y significación con las variables económicas más importantes que definen a una compañía del sector del automóvil, utilizando la técnica estadística de regresión lineal. Aquellas variables relacionadas con la competencia en el mercado, la externalización de las actividades de menor valor añadido y el incremento de la modularización de las actividades de la cadena de valor, han resultado significativas con la práctica del outsourcing. En el estudio de la fragmentación se seleccionan un conjunto de factores macroeconómicos, comúnmente usados en este tipo de investigaciones, relacionados con las principales magnitudes económicas de un país, y un conjunto de factores macroeconómicos, no comúnmente usados en este tipo de investigaciones, relacionados con la libertad económica y el comercio internacional de un país. Se emplea un modelo de regresión logística para identificar qué factores son significativos en la práctica de la fragmentación. De entre todos los factores usados en el modelo, los relacionados con las economías de escala y los costes de servicio han resultado significativos. Los resultados obtenidos de los test estadísticos realizados en el modelo de regresión logística han resultado satisfactorios; por ello, el modelo propuesto de regresión logística puede ser considerado sólido, fiable y versátil; además, acorde con la realidad. De los resultados obtenidos en el estudio del outsourcing y de la fragmentación, combinados conjuntamente con el estado del arte, se concluye que el principal factor que desencadena la desintegración vertical en la industria del automóvil es la competencia en el mercado de vehículos. Cuanto mayor es la demanda de vehículos, más se reducen los beneficios y la rentabilidad para sus fabricantes. Estos, para ser competitivos, diferencian sus productos de la competencia centrándose en las actividades que mayor valor añadido aportan al producto final, externalizando las actividades de menor valor añadido a proveedores especializados, e incrementando la modularidad de las actividades de la cadena de valor. Las compañías de la industria del automóvil se especializan en alguna o varias de estas actividades modularizadas que, combinadas con el uso de factores facilitadores como las economías de escala, las tecnologías de la información, las ventajas de la globalización económica y la aglomeración geográfica de una industria, incrementan y motivan la desintegración vertical en la industria del automóvil, desencadenando la coespecialización en dos sectores claramente diferenciados: el sector de fabricantes de vehículos y el sector de proveedores especializados. Cada uno de ellos se especializa en unas actividades y en unos productos o servicios específicos de la cadena de valor, lo cual genera las siguientes consecuencias en la industria del automóvil: se reducen los costes de transacción en los productos o servicios intercambiados; se incrementan la relación de dependencia entre fabricantes de vehículos y proveedores especializados, provocando un aumento en la cooperación y la coordinación, acelerando el proceso de aprendizaje, posibilitando a ambos adquirir nuevas capacidades, conocimientos y recursos, y creando nuevas ventajas competitivas para ambos; por último, las barreras de entrada a la industria del automóvil y el número de compañías se ven alteradas cambiando su estructura. Como futura línea de investigación, los fabricantes de vehículos tenderán a centrarse en investigar, diseñar y comercializar el producto o servicio, delegando el ensamblaje en manos de nuevos especialistas en la materia, el contract manufacturer; por ello, sería conveniente investigar qué factores motivantes o facilitadores existen y qué consecuencias tendría la implantación de los contract manufacturer en la industria del automóvil. 1.1. ABSTRACT In recent years there has been a rapid growth of international trade in semi-finished products designed, produced and assembled in different locations across different countries, mainly due to the following reasons: development of information technologies, reduction of transportation costs, liberalisation of capital markets, harmonisation of institutional factors, regional economic integration, which involves the reduction and elimination of trade barriers, economic development of emerging countries, use of economies of scale and deregulation of international trade. All these factors have increased competition in markets at a global level and have allowed companies to gain easier access to potential markets and to the acquisition of skills and knowledge in other countries, as well as to the completion of international strategic alliances with third parties, thus creating a more demanding and uncertain environment for these companies constituting an industry, which has a direct impact on the companies' operations and the organization of their production. In order to adapt, be competitive and benefit from this new and more competitive global scenario, companies have outsourced some parts of their production process to specialist suppliers, generating a new intermediate market which divides the production process, previously integrated in the companies that made up the industry, into two sets of companies specialized in that industry. This process often occurs while preserving the industry where it takes place, its same services and products, the technology used and the original companies that formed it prior to vertical disintegration. This is because it is beneficial for both the industry's original companies and the companies belonging to this new intermediate market, for various reasons. Vertical disintegration has consequences which completely transform the industry where it takes place as well as the modus operandi of the companies that are part of it, even of those who remain vertically integrated. One of the most important features of vertical disintegration of an industry is the possibility for a company to acquire from a third one the first part of the production process or a semi-finished product, which will then be finished by the acquiring company through the practice of outsourcing; also, a company can perform the first part of the production process or a semi-finish product, which will then be completed by a third company through the practice of fragmentation. The main objective of this research is to study the motives, facilitators, effects, consequences and major significant microeconomic and macroeconomic factors that trigger or increase the practice of vertical disintegration in a certain industry; in order to do so, research is divided into two completely differentiated lines: on the one hand, the study of the practise of outsourcing and, on the other, the study of fragmentation by companies constituting the automotive industry in Spain, since this is one of the most vertically disintegrated and fragmented industries and this particular sector is of major significance in this country's economy. First, a review is made of the existing literature, on the following aspects: vertical disintegration, outsourcing, fragmentation, international trade theory, history of the automobile industry in Spain and the use of geographical agglomeration and information technologies in the automotive sector. The methodology used for each of these aspects has been different depending on the availability of data and the research approach: the microeconomic factors, using outsourcing, and the macroeconomic factors, using fragmentation. In the study on outsourcing, an index is used based on external purchases in relation to the total value of production. Likewise, their significance and correlation with the major economic variables that define an automotive company are studied, using the statistical technique of linear regression. Variables related to market competition, outsourcing of lowest value-added activities and increased modularisation of the activities of the value chain have turned out to be significant with the practice of outsourcing. In the study of fragmentation, a set of macroeconomic factors commonly used for this type of research, is selected, related to the main economic indicators of a country, as well as a set of macroeconomic factors, not commonly used for this type of research, which are related to economic freedom and the international trade of a certain country. A logistic regression model is used to identify which factors are significant in the practice of fragmentation. Amongst all factors used in the model, those related to economies of scale and service costs have turned out to be significant. The results obtained from the statistical tests performed on the logistic regression model have been successful; hence, the suggested logistic regression model can be considered to be solid, reliable and versatile; likewise, it is in line with reality. From the results obtained in the study of outsourcing and fragmentation, combined with the state of the art, it is concluded that the main factor that triggers vertical disintegration in the automotive industry is competition within the vehicle market. The greater the vehicle demand, the lower the earnings and profitability for manufacturers. These, in order to be competitive, differentiate their products from the competition by focusing on those activities that contribute with the highest added value to the final product, outsourcing the lower valueadded activities to specialist suppliers, and increasing the modularity of the activities of the value chain. Companies in the automotive industry specialize in one or more of these modularised activities which, combined with the use of enabling factors such as economies of scale, information technologies, the advantages of economic globalisation and the geographical agglomeration of an industry, increase and encourage vertical disintegration in the automotive industry, triggering co-specialization in two clearly distinct sectors: the sector of vehicle manufacturers and the specialist suppliers sector. Each of them specializes in certain activities and specific products or services of the value chain, generating the following consequences in the automotive industry: reduction of transaction costs of the goods or services exchanged; growth of the relationship of dependency between vehicle manufacturers and specialist suppliers, which causes an increase in cooperation and coordination, accelerates the learning process, enables both to acquire new skills, knowledge and resources, and creates new competitive advantages for both; finally, barriers to entry the automotive industry and the number of companies are altered, changing their structure. As a future line of research, vehicle manufacturers will tend to focus on researching, designing and marketing the product or service, delegating the assembly in the hands of new specialists in the field, the contract manufacturer; for this reason, it would be useful to investigate what motivating or facilitating factors exist in this respect and what consequences would the implementation of contract manufacturers have in the automotive industry.

Simulación atomística de metales líquidos y aleaciones para reactores de fusión nuclear = Atomistic simulation of liquid metals and alloys for nuclear fusion reactors

La presente tesis comprende un estudio de metales líquidos, Li, Pb y eutéctico Li17Pb en el ámbito de la tecnología de fusión nuclear. Uno de los problemas fundamentales en futuros reactores de fusión es la producción y extracción de tritio en la denominada envoltura regeneradora (blanket en inglés). Dicho blanket tendrá dos propósitos, la extracción del calor generado por las reacciones de fusión para su posterior conversión en energía eléctrica así como la producción de tritio para realimentar el proceso. Dicha producción se realizará mediante el “splitting” del Li con los neutrones provenientes de la fusión. Esta reacción produce tritio y helio por lo que la interacción del T y el He con el metal líquido, con los materiales estructurales así como con el He es un problema fundamental aun no bien entendido y de gran importancia para futuros diseños. Los capítulos 1 2 y 3 presentan una introducción a dichos problemas. El capítulo 1 introduce al lector en la tecnología de fusión nuclear. El segundo capítulo explica en mayor detalle el uso de metales líquidos en reactores de fusión, no solo en blankets sino también como primera pared, divertor etc, lo que se denomina en general “plasma facing materials”. Por último se ofrece una breve introducción a las técnicas de dinámica molecular clásica (CMD) y un breve resumen de los potenciales más usados. El estudio se ha llevado a cabo utilizando simulación atomística mediante potenciales semi-empíricos del tipo átomo embebido (EAM). La Tesis consta de 4 partes bien definidas. En primer lugar se verificó la idoneidad de los potenciales tipo EAM para simular las propiedades de los metales Li y Pb en fase líquida. Dicho estudio se detalla en el Capítulo 4 y en su extensión, el Apéndice 1, en el que se estudia los límites de validez de esta aproximación. Los resultados de dicho estudio han sido publicados y presentados en diversos congresos internacionales. Un resumen de la metodología seguida fue publicado como capítulo de libro en Technofusión 2011. Los resultados se presentaron en diversos congresos internacionales, entre ellos ICENES 2011, (Artículo en ICENES Proceedings) ICOPS-SOFE 2011, en una presentación oral etc. El trabajo ha sido aceptado recientemente en Journal of Nuclear Materiales (Fraile et al 2012). La segunda parte y más importante comprende el desarrollo de un potencial para el estudio de la mezcla de ambos metales. Éste es el trabajo más novedoso e importante dado que no existía en la literatura un potencial semejante. Se estudiaron dos aproximaciones distintas al problema, un potencial tipo EAM/cd y un potencial EAM/alloy. Ambos potenciales dan resultados satisfactorios para la simulación del eutéctico (y concentraciones de Li menores que el 17%). Sin embargo el sistema LiPb en todas las concentraciones es un sistema que se aparta enormemente de una solución ideal y dicho potencial no daba buenos resultados para mezclas PbLi con concentraciones de Li grandes. Este problema fue solventado mediante el desarrollo de un segundo potencial, esta vez tipo EAM/alloy (segunda parte del Capítulo 5). Dicho trabajo será enviado a Physical Review Letters o a Phys. Rev. B, y una extensión junto con un estudio detallado de las propiedades del eutéctico de acuerdo con nuestras simulaciones se enviará a continuación a Phys. Rev. B. En tercer lugar se estudió el problema de la difusividad del H en metales líquidos aprovechando distintos potenciales existentes en la literatura. El problema del H en metales líquidos es importante en metalurgia. En dicho capítulo se estudió la difusividad del H en Pd, Ni y Al con potenciales tipo EAM, y también con un potencial más sofisticado que tiene en cuenta la dependencia angular de las interacciones (ADP por sus siglas en inglés). De este modo disponemos de un estudio detallado del problema con diferentes modelos y diferentes metales. La conclusión apunta a que si se compara con los resultados experimentales (muy escasos) los resultados obtenidos mediante CMD dan valores bajos de la difusividad del H. Las razones de dicho desacuerdo entre simulación y experimentos se detallan en el Capítulo 6. Este trabajo ha sido presentado en una presentación oral en el reciente congreso internacional “Trends on Nanothecnology” TNT 2012 celebrado en Madrid. El trabajo será publicado en un futuro próximo. Por último, como se dijo anteriormente, el estudio del He, la formación de burbujas en metales líquidos, su difusión nucleación y cavitación es otro problema deseable de ser estudiado mediante técnicas atomísticas. Para ello es necesario el desarrollo de diversos potenciales, He-Li, He-Pb y un potencial ternario Pb-Li-He. Para ello se han realizado simulación ab initio de los sistemas Pb+He y Li+He. Dicho estudio pretende calcular las fuerzas entre los átomos del metal (Pb o Li) con intersticiales de He. De este modo aplicaremos el “force matching method” (FMM) para el desarrollo de dichos potenciales. En el Capítulo 7 se detallan los resultados obtenidos referidos a las posiciones más favorables de las impurezas de He dentro de redes cristalinas de Pb y Li así como el efecto de tener en cuenta el acoplo spin-orbita (SOC en inglés). El análisis de los resultados en términos de transferencia de carga y análisis de las densidades electrónicas, así como la creación de los potenciales mencionados está en progreso. En conjunto la tesis presenta un estudio de los diversos problemas relacionados con el uso de metales líquidos en reactores de fusión y representa un primer paso en la determinación de parámetros de gran importancia para el diseño de blankets y sistemas de primera pared. Con la simulación MD de dichos problemas mediante, importante, potenciales realistas, valores de difusión, solubilidad etc de especies ligeras, H (o sus isotopos) y He en metales líquidos podrá ser calculada complementando así la base de datos que presenta enormes incertidumbres.

Determination of the magnetostrictive atomic enviroments in FeCoB alloys

The atomic environments of Fe and Co involved in the magnetostriction effect in FeCoB alloys have been identified by differential extended x-ray fine structure (DiffEXAFS) spectroscopy. The study, done in amorphous and polycrystalline FeCoB films, demonstrates that the alloys are heterogeneous and that boron plays a crucial role in the origin of their magnetostrictive properties. The analysis of DiffEXAFS in the polycrystalline and amorphous alloys indicates that boron activates magnetostriction when entering as an impurity into octahedral interstitial sites of the Fe bcc lattice, causing its tetragonal distortion. Magnetostriction would be explained then by the relative change in volume when the tetragonal axis of the site is reoriented under an externally applied magnetic field. The experiment demonstrates the extreme sensitivity of DiffEXAFS to characterize magnetostrictive environments that are undetectable in their related EXAFS spectra.

Stability of vacancy clusters in FeCr alloys: A study of the Cr concentration dependence

Fe–Cr based alloys are the leading structural material candidates in the design of next generation reactors due to their high resistance to swelling and corrosion. Despite these good properties there are others, such as embrittlement, which require a higher level of understanding in order to improve aspects such as safety or lifetime of the reactors. The addition of Cr improves the behavior of the steels under irradiation, but not in a monotonic way. Therefore, understanding the changes in the Fe–Cr based alloys microstructure induced by irradiation and the role played by the alloying element (Cr) is needed in order to predict the response of these materials under the extreme conditions they are going to support. In this work we perform a study of the effect of Cr concentration in a bcc Fe–Cr matrix on formation and binding energies of vacancy clusters up to 5 units. The dependence of the calculated formation and binding energy is investigated with two empirical interatomic potentials specially developed to study radiation damage in Fe–Cr alloys. Results are very similar for both potentials showing an increase of the defect stability with the cluster size and no real dependence on Cr concentration for the binding energy.

A comprehensive diagram to grow metal-polarity InGaN alloys by molecular beam epitaxy

he composition, strain and surface morphology of (0001)InGaN layers are investigated as a function of growth temperature (460–645 °C) and impinging In flux. Three different growth regimes: nitrogen-rich, metal-rich and intermediate metal-rich, are clearly identified and found to be in correlation with surface morphology and strain relaxation. Best epilayers’ quality is obtained when growing under intermediate metal-rich conditions, with 1–2 monolayers thick In ad-coverage. For a given In flux, the In incorporation decreases with increasing growth temperature due to InN thermal decomposition that follows an Arrhenius behavior with 1.84±0.12 eV activation energy.