Aspects of a phased array radar feed and bias network design

Radar technologies have been developed to improve the efficiency when detecting targets. Radar is a system composed by several devices connected and working together. Depending on the type of radar, the improvements are focused on different functionalities of the radar. One of the most important devices composing a radar is the antenna, that sends the radio-frequency signal to the space in order to detect targets. This project is focused on a specific type of radar called phased array radar. This type of radar is characterized by its antenna, which consist on a linear array of radiating elements, in this particular case, eight dipoles working at the frequency band S. The main advantage introduced by the phased array antenna is that using the fundamentals of arrays, the directivity of the antenna can change by shifting the phase of the signal at the input of each radiating element. This can be done using phase shifters. Phase shifter consists on a device which produces a phase shift in the radio-frequency input signal depending on a control DC voltage. Using a phased array antenna allows changing the directivity of the antenna without a mechanical rotating system. The objective of this project is to design the feed network and the bias network of the phased antenna. The feed network consists on a parallel-fed network composed by power dividers that sends the radio-frequency signal from the source to each radiating element of the antenna. The bias network consists on a system that generates the control DC voltages supplied to the phase shifters in order to change the directivity. The architecture of the bias network is composed by a software, implemented in Matlab and run in a laptop which is connected to a micro-controller by a serial communication port. The software calculates the control DC voltages needed to obtain a determined directivity or scan angle. These values are sent by the serial communication port to the micro-controller as data. Then the micro-controller generates the desired control DC voltages and supplies them to the phase shifters. In this project two solutions for bias network are designed. Each one is tested and final conclusions are obtained to determine the advantages and disadvantages. Finally a graphic user interface is developed in order to make the system easy to use. RESUMEN. Las tecnologías empleadas por lo dispositivos radar se han ido desarrollando para mejorar su eficiencia y usabilidad. Un radar es un sistema formado por varios subsistemas conectados entre sí. Por lo que dependiendo del tipo de radar las mejoras se centran en los subsistemas correspondientes. Uno de los elementos más importantes de un radar es la antena. Esta se emplea para enviar la señal de radiofrecuencia al espacio y así poder detectar los posibles obstáculos del entorno. Este proyecto se centra en un tipo específico de radar llamado phased array radar. Este tipo de radar se caracteriza por la antena que es un array de antenas, en concreto para este proyecto se trata de un array lineal de ocho dipolos en la banda de frequencia S. El uso de una antena de tipo phased array supone una ventaja importante. Empleando los fundamentos de radiación aplicado a array de antenas se obtiene que la directividad de la antena puede ser modificada. Esto se consigue aplicando distintos desfasajes a la señal de radiofrecuencia que alimenta a cada elemento del array. Para aplicar los desfasajes se emplea un desplazador de fase, este dispositivo aplica una diferencia de fase a su salida con respecto a la señal de entrada dependiendo de una tensión continua de control. Por tanto el empleo de una antena de tipo phased array supone una gran ventaja puesto que no se necesita un sistema de rotación para cambiar la directividad de la antena. El objetivo principal del proyecto consiste en el diseño de la red de alimentación y la red de polarización de la antena de tipo phased array. La red de alimentación consiste en un circuito pasivo que permite alimentar a cada elemento del array con la misma cantidad de señal. Dicha red estará formada por divisores de potencia pasivos y su configuración será en paralelo. Por otro lado la red de polarización consiste en el diseño de un sistema automático que permite cambiar la directividad de la antena. Este sistema consiste en un programa en Matlab que es ejecutado en un ordenador conectado a un micro-controlador mediante una comunicación serie. El funcionamiento se basa en calcular las tensiones continuas de control, que necesitan los desplazadores de fase, mediante un programa en Matlab y enviarlos como datos al micro-controlador. Dicho micro-controlador genera las tensiones de control deseadas y las proporciona a cada desplazador de fase, obteniendo así la directividad deseada. Debido al amplio abanico de posibilidades, se obtienen dos soluciones que son sometidas a pruebas. Se obtienen las ventajas y desventajas de cada una. Finalmente se implementa una interfaz gráfica de usuario con el objetivo de hacer dicho sistema manejable y entendible para cualquier usuario.

Planar compact array with parasitic elements for MIMO systems

A compact planar array with parasitic elements is studied to be used in MIMO systems. Classical compact arrays suffer from high coupling which makes correlation and matching efficiency to be worse. A proper matching network improves these lacks although its bandwidth is low and may increase the antenna size. The proposed antenna makes use of parasitic elements to improve both correlation and efficiency. A specific software based on MoM has been developed to analyze radiating structures with several feed points. The array is optimized through a Genetic Algorithm to determine parasitic elements position in order to fulfill different figures of merit. The proposed design provides the required correlation and matching efficiency to have a good performance over a significant bandwidth.

Multibeam Network Design and Measurement for Triangular Array of Three Radiating Elements

Nowadays, more a more base stations are equipped with active conformal antennas. These antenna designs combine phase shift systems with multibeam networks providing multi-beam ability and interference rejection, which optimize multiple channel systems. GEODA is a conformal adaptive antenna system designed for satellite communications. Operating at 1.7 GHz with circular polarization, it is possible to track and communicate with several satellites at once thanks to its adaptive beam. The antenna is based on a set of similar triangular arrays that are divided in subarrays of three elements called `cells'. Transmission/Receiver (T/R) modules manage beam steering by shifting the phases. A more accurate steering of the antenna GEODA could be achieved by using a multibeam network. Several multibeam network designs based on Butler network will be presented

3x3 Multibeam Network for a Triangular Array of Three Radiating Elements

A multibeam antenna study based on Butler network will be undertaken in this document. These antenna designs combines phase shift systems with multibeam networks to optimize multiple channel systems. The system will work at 1.7 GHz with circular polarization. Specifically, result simulations and measurements of 3 element triangular subarray will be shown. A 45 element triangular array will be formed by the subarrays. Using triangular subarrays, side lobes and crossing points are reduced.

6x3 Microstrip Beam Forming Network for Multibeam Triangular Array

A six inputs and three outputs structure which can be used to obtain six simultaneous beams with a triangular array of 3 elements is presented. The beam forming network is obtained combining balanced and unbalanced hybrid couplers and allows to obtain six main beams with sixty degrees of separation in azimuth direction. Simulations and measurements showing the performance of the array and other detailed results are presented

Low-Profile Dual Circularly Polarized Antenna Array for Satellite Communications in the X Band

A planar antenna is introduced that works as a portable system for X-band satellite communications. This antenna is low-profile and modular with dimensions of 40 × 40 × 2.5 × cm. It is composed of a square array of 144 printed circuit elements that cover a wide bandwidth (14.7%) for transmission and reception along with dual and interchangeable circular polarization. A radiation efficiency above 50% is achieved by a low-loss stripline feeding network. This printed antenna has a 3 dB beamwidth of 5°, a maximum gain of 26 dBi and an axial ratio under 1.9 dB over the entire frequency band. The complete design of the antenna is shown, and the measurements are compared with simulations to reveal very good agreement.

Study of the II Network as the Compound Slot Equivalent Circuit Model

A combination of Method of Moments (MoM) and compound slot Equivalent Circuit Model for linear array design is presented in this document. From the S Matrix of the single element, the more suitable network for its characterization is analyzed and selected. Then according to the radiation requirements of the desired array, the elements are designed and then properly connected by means of Forward Matching Procedure (FMP), which takes into account impedance matters in order to keep the input matched at the designing frequency. Comparison between HFSS simulations and MoM-FMP results are also presented. First part of this work was introduced in (1)(2) but a summary is included here to make the understanding easier.

Array Compacto De Monopolos Planos Con Plano De Tierra Ranurado Para Sistemas Mimo

A compact array of monopoles with a slotted ground plane is analyzed for being used in MIMO systems. Compact arrays suffer usually from high coupling which degrades significantly MIMO benefits. Through a matching network, main drawbacks can be solved, although it tends to provide a low bandwidth. The studied design is an array of monopoles with a slot in the ground plane. The slot shape is optimized with a Genetic Algorithm and an own electromagnetic software based on MoM in order to fulfill main figures of merit within a significant bandwidth

Low losses power distribution network at X band in stripline

An asymmetric stripline is proposed in this paper. The main aim of this line is to distribute the power among subarrays in an array with minimum losses. Several vertical transitions to subarrays are shown besides some network designs at X band for a square array for satellite communications.

On the design and measurement of a novel non-orthogonal multi-beam network for triangular arrays of three radiating elements

An innovative dissipative multi-beam network for triangular arrays of three radiating elements is proposed. This novel network provides three orthogonal beams in θ0 elevation angle and a fourth one in the broadside steering direction. The network is composed of 90º hybrid couplers and fixed phase shifters. In this paper, a relation between network components, radiating element distance and beam steering directions will be shown. Application of the proposed dissipative network to the triangular cells of three radiating elements that integrate the intelligent antenna GEODA will be exhibited. This system works at 1.7 GHz, it has a 60º single radiating element beamwidth and a distance between array elements of 0.57 λ. Both beam patterns, theoretical and simulated, obtained with the network will be depicted. Moreover, the whole system, dissipative network built with GEODA cell array, has been measured in the anechoic chamber of the Radiation Group of Technical University of Madrid, demonstrating expected performance.

Study of a new 4×3 beam forming network for triangular arrays of three radiating elements

An innovative dissipative multi-beam network for triangular arrays of three radiating elements is proposed. This novel network provides three orthogonal beams in θ0 elevation angle and a fourth one in the broadside steering direction. The network is composed of 90º hybrid couplers and fixed phase shifters. In this paper, a relation between network components, radiating element distance and beam steering directions will be shown. Application of the proposed dissipative network to the triangular cells of three radiating elements that integrate the intelligent antenna GEODA will be exhibited. This system works at 1.7 GHz, it has a 60º single radiating element beamwidth and a distance between array elements of 0.57λ. Both beam patterns, theoretical and simulated, obtained with the network will be depicted. Moreover, the whole system, dissipative network built with GEODA cell array, has been measured in the anechoic chamber of the Radiation Group of Technical University of Madrid, demonstrating expected performance

Structural health monitoring network system with wireless communications inside closed aerospace structures

Structural Health Monitoring (SHM) requires integrated "all in one" electronic devices capable of performing analysis of structural integrity and on-board damage detection in aircraft?s structures. PAMELA III (Phased Array Monitoring for Enhanced Life Assessment, version III) SHM embedded system is an example of this device type. This equipment is capable of generating excitation signals to be applied to an array of integrated piezoelectric Phased Array (PhA) transducers stuck to aircraft structure, acquiring the response signals, and carrying out the advanced signal processing to obtain SHM maps. PAMELA III is connected with a host computer in order to receive the configuration parameters and sending the obtained SHM maps, alarms and so on. This host can communicate with PAMELA III through an Ethernet interface. To avoid the use of wires where necessary, it is possible to add Wi-Fi capabilities to PAMELA III, connecting a Wi-Fi node working as a bridge, and to establish a wireless communication between PAMELA III and the host. However, in a real aircraft scenario, several PAMELA III devices must work together inside closed structures. In this situation, it is not possible for all PAMELA III devices to establish a wireless communication directly with the host, due to the signal attenuation caused by the different obstacles of the aircraft structure. To provide communication among all PAMELA III devices and the host, a wireless mesh network (WMN) system has been implemented inside a closed aluminum wingbox. In a WMN, as long as a node is connected to at least one other node, it will have full connectivity to the entire network because each mesh node forwards packets to other nodes in the network as required. Mesh protocols automatically determine the best route through the network and can dynamically reconfigure the network if a link drops out. The advantages and disadvantages on the use of a wireless mesh network system inside closed aerospace structures are discussed.

Contribución a los arrays de antenas activos en microondas = Contribution to active array antennas at microwave bands

Esta tesis que tiene por título "Contribución a los arrays de antenas activos en banda X", ha sido desarrollada por el estudiante de doctorado Gonzalo Expósito Domínguez, ingeniero de telecomunicación en el Grupo de Radiación del Departamento de Señales, Sistemas y Radiocomunicaciones de la ETSI de Telecomunicación de la Universidad Politécnica de Madrid bajo la dirección de los doctores Manuel Sierra Castañer y José Manuel Fernández González. Esta tesis contiene un profundo estudio del arte en materia de antenas activas en el campo de apuntamiento electrónico. Este estudio comprende desde los fundamentos de este tipo de antenas, problemas de operación y limitaciones hasta los sistemas actuales más avanzados. En ella se identifican las partes críticas en el diseño y posteriormente se llevan a la práctica con el diseño, simulación y construcción de un subarray de una antena integrada en el fuselaje de un avión para comunicaciones multimedia por satélite que funciona en banda X. El prototipo consta de una red de distribución multihaz de banda ancha y una antena planar. El objetivo de esta tesis es el de aplicar nuevas técnicas al diseño de antenas de apuntamiento electrónico. Es por eso que las contribuciones originales son la aplicación de barreras electromagnéticas entre elementos radiantes para reducir los acoplamientos mutuos en arrays de exploración electrónica y el diseño de redes desfasadoras sencillas en las que no son necesarios complejos desfasadores para antenas multihaz. Hasta la fecha, las barreras electromagnéticas, Electronic Band Gap (EBG), se construyen en sustratos de permitividad alta con el fin de aumentar el espacio disponible entre elementos radiantes y reducir el tamaño de estas estructuras. Sin embargo, la utilización de sustratos de alta permitividad aumenta la propagación por ondas de superficie y con ellas el acoplo mutuo. Utilizando sustratos multicapa y colocando la vía de las estructuras en su borde, en vez de en su centro, se consigue reducir el tamaño sin necesidad de usar sustratos de alta permitividad, reducir la eficiencia de radiación de la antena o aumentar la propagación por ondas de superficie. La última parte de la tesis se dedica a las redes conmutadoras y desfasadoras para antenas multihaz. El diseño de las redes de distribución para antenas son una parte crítica ya que se comportan como un atenuador a la entrada de la cadena receptora, modificando en gran medida la figura de ruido del sistema. Las pérdidas de un desfasador digital varían con el desfase introducido, por ese motivo es necesario caracterizar y calibrar los dispositivos correctamente. Los trabajos presentados en este manuscrito constan de un desfasador reflectivo con un conmutador doble serie paralelo para igualar las pérdidas de inserción en los dos estados y también un conmutador de una entrada y dos salidas cuyos puertos están adaptados en todo momento independientemente del camino del conmutador para evitar las reflexiones y fugas entre redes o elementos radiantes. El tomo finaliza con un resumen de las publicaciones en revistas científicas y ponencias en congresos, nacionales e internacionales, el marco de trabajo en el que se ha desarrollado, las colaboraciones que se han realizado y las líneas de investigación futuras. ABSTRACT This thesis was carried out in the Radiation Group of the Signals, Systems and Radiocomunications department of ETSI de Telecomunicación from Technical University of Madrid. Its title is "Contribution to active array antennas at X band" and it is developed by Gonzalo Expósito Domínguez, Electrical Engineer MsC. under the supervision of Prof. Dr. Manuel Sierra Castañer and Dr. José Manuel Fernández González. This thesis is focused on active antennas, specifically multibeam and electronic steering antenas. In the first part of the thesis a thorough description of the state of the art is presented. This study compiles the fundamentals of this antennas, operation problems and limits, up to the breakthrough applications. The critical design problems are described to use them eventually in the design, simulation and prototyping of an airborne steering array antenna for satellite communication at X band. The main objective of this thesis is to apply new techniques to the design of electronically steering antennas. Therefore the new original contributions are the application of Electromagnetic Band Gap materials (EBG) between radiating elements to reduce the mutual coupling when phase shift between elements exist and phase shifting networks where special characteristics are required. So far, the EBG structures have been constructed with high permitivity substrates in order to increase the available space between radiating elements and reduce the size of the structures. However, the surface wave propagation modes are enhanced and therefore the mutual coupling increases when high permitivity substrates are used. By using multilayered substrates and edge location via, the size is reduced meanwhile low permitivity substrates are used without reducing the radiation efficiency or enhancing the surface propagation modes. The last part of the thesis is focused on the phase shifting distribution networks for multibeam antennas. This is a critical part in the antenna design because the insertion loss in the distribution network behaves as an attenuator located in the first place in a receiver chain. The insertion loss will affect directly to the receiver noise figure and the insertion loss in a phase shifter vary with the phase shift. Therefore the devices must be well characterized and calibrated in order to obtain a properly operation. The work developed in this thesis are a reflective phase shifter with a series-shunt switch in order to make symmetrical the insertion loss for the two states and a complex Single Pole Double Through (SPDT) with matched ports in order to reduce the reflections and leakage between feeding networks and radiating elements. The end of this Ph D. dissertation concludes with a summary of the publications in national and international conferences and scientific journals, the collaborations carried out along the thesis and the future research lines.

Novel dual-band single circular polarization antenna feeding network for satellite communications

In this paper a novel dual-band single circular polarization antenna feeding network for satellite communications is presented. The novel antenna feed chain1 is composed of two elements or subsystems, namely a diplexer and a bi-phase polarizer. In comparison with the classic topology based on an orthomode transducer and a dual-band polarizer, the proposed feed chain presents several advantages, such as compactness, modular design of the different components, broadband operation and versatility in the subsystems interconnection. The design procedure of this new antenna feed configuration is explained. Different examples of antenna feeding networks at 20/30 GHz are presented. It is pointed out the excellent results obtained in terms of isolation and axial ratio.