Biosensors based on vertically interrogated optofluidic sensing cells

El objetivo de la presente tesis doctoral es el desarrollo de un nuevo concepto de biosensor óptico sin marcado, basado en una combinación de técnicas de caracterización óptica de interrogación vertical y estructuras sub-micrométricas fabricadas sobre chips de silicio. Las características más importantes de dicho dispositivo son su simplicidad, tanto desde el punto de vista de medida óptica como de introducción de las muestras a medir en el área sensible, aspectos que suelen ser críticos en la mayoría de sensores encontrados en la literatura. Cada uno de los aspectos relacionados con el diseño de un biosensor, que son fundamentalmente cuatro (diseño fotónico, caracterización óptica, fabricación y fluídica/inmovilización química) son desarrollados en detalle en los capítulos correspondientes. En la primera parte de la tesis se hace una introducción al concepto de biosensor, en qué consiste, qué tipos hay y cuáles son los parámetros más comunes usados para cuantificar su comportamiento. Posteriormente se realiza un análisis del estado del arte en la materia, enfocado en particular en el área de biosensores ópticos sin marcado. Se introducen también cuáles son las reacciones bioquímicas a estudiar (inmunoensayos). En la segunda parte se describe en primer lugar cuáles son las técnicas ópticas empleadas en la caracterización: Reflectometría, Elipsometría y Espectrometría; además de los motivos que han llevado a su empleo. Posteriormente se introducen diversos diseños de las denominadas "celdas optofluídicas", que son los dispositivos en los que se va a producir la interacción bioquímica. Se presentan cuatro dispositivos diferentes, y junto con ellos, se proponen diversos métodos de cálculo teórico de la respuesta óptica esperada. Posteriormente se procede al cálculo de la sensibilidad esperada para cada una de las celdas, así como al análisis de los procesos de fabricación de cada una de ellas y su comportamiento fluídico. Una vez analizados todos los aspectos críticos del comportamiento del biosensor, se puede realizar un proceso de optimización de su diseño. Esto se realiza usando un modelo de cálculo simplificado (modelo 1.5-D) que permite la obtención de parámetros como la sensibilidad y el límite de detección de un gran número de dispositivos en un tiempo relativamente reducido. Para este proceso se escogen dos de las celdas optofluídicas propuestas. En la parte final de la tesis se muestran los resultados experimentales obtenidos. En primer lugar, se caracteriza una celda basada en agujeros sub-micrométricos como sensor de índice de refracción, usando para ello diferentes líquidos orgánicos; dichos resultados experimentales presentan una buena correlación con los cálculos teóricos previos, lo que permite validar el modelo conceptual presentado. Finalmente, se realiza un inmunoensayo químico sobre otra de las celdas propuestas (pilares nanométricos de polímero SU-8). Para ello se utiliza el inmunoensayo de albumina de suero bovino (BSA) y su anticuerpo (antiBSA). Se detalla el proceso de obtención de la celda, la funcionalización de la superficie con los bioreceptores (en este caso, BSA) y el proceso de biorreconocimiento. Este proceso permite dar una primera estimación de cuál es el límite de detección esperable para este tipo de sensores en un inmunoensayo estándar. En este caso, se alcanza un valor de 2.3 ng/mL, que es competitivo comparado con otros ensayos similares encontrados en la literatura. La principal conclusión de la tesis es que esta tipología de dispositivos puede ser usada como inmunosensor, y presenta ciertas ventajas respecto a los actualmente existentes. Estas ventajas vienen asociadas, de nuevo, a su simplicidad, tanto a la hora de medir ópticamente, como dentro del proceso de introducción de los bioanalitos en el área sensora (depositando simplemente una gota sobre la micro-nano-estructura). Los cálculos teorícos realizados en los procesos de optimización sugieren a su vez que el comportamiento del sensor, medido en magnitudes como límite de detección biológico puede ser ampliamente mejorado con una mayor compactación de pilares, alcanzandose un valor mínimo de 0.59 ng/mL). The objective of this thesis is to develop a new concept of optical label-free biosensor, based on a combination of vertical interrogation optical techniques and submicron structures fabricated over silicon chips. The most important features of this device are its simplicity, both from the point of view of optical measurement and regarding to the introduction of samples to be measured in the sensing area, which are often critical aspects in the majority of sensors found in the literature. Each of the aspects related to the design of biosensors, which are basically four (photonic design, optical characterization, fabrication and fluid / chemical immobilization) are developed in detail in the relevant chapters. The first part of the thesis consists of an introduction to the concept of biosensor: which elements consists of, existing types and the most common parameters used to quantify its behavior. Subsequently, an analysis of the state of the art in this area is presented, focusing in particular in the area of label free optical biosensors. What are also introduced to study biochemical reactions (immunoassays). The second part describes firstly the optical techniques used in the characterization: reflectometry, ellipsometry and spectrometry; in addition to the reasons that have led to their use. Subsequently several examples of the so-called "optofluidic cells" are introduced, which are the devices where the biochemical interactions take place. Four different devices are presented, and their optical response is calculated by using various methods. Then is exposed the calculation of the expected sensitivity for each of the cells, and the analysis of their fabrication processes and fluidic behavior at the sub-micrometric range. After analyzing all the critical aspects of the biosensor, it can be performed a process of optimization of a particular design. This is done using a simplified calculation model (1.5-D model calculation) that allows obtaining parameters such as sensitivity and the detection limit of a large number of devices in a relatively reduced time. For this process are chosen two different optofluidic cells, from the four previously proposed. The final part of the thesis is the exposition of the obtained experimental results. Firstly, a cell based sub-micrometric holes is characterized as refractive index sensor using different organic fluids, and such experimental results show a good correlation with previous theoretical calculations, allowing to validate the conceptual model presented. Finally, an immunoassay is performed on another typology of cell (SU-8 polymer pillars). This immunoassay uses bovine serum albumin (BSA) and its antibody (antiBSA). The processes for obtaining the cell surface functionalization with the bioreceptors (in this case, BSA) and the biorecognition (antiBSA) are detailed. This immunoassay can give a first estimation of which are the expected limit of detection values for this typology of sensors in a standard immunoassay. In this case, it reaches a value of 2.3 ng/mL, which is competitive with other similar assays found in the literature. The main conclusion of the thesis is that this type of device can be used as immunosensor, and has certain advantages over the existing ones. These advantages are associated again with its simplicity, by the simpler coupling of light and in the process of introduction of bioanalytes into the sensing areas (by depositing a droplet over the micro-nano-structure). Theoretical calculations made in optimizing processes suggest that the sensor Limit of detection can be greatly improved with higher compacting of the lattice of pillars, reaching a minimum value of 0.59 ng/mL).

Building functional surfaces for biosensors development

Polyelectrolyte multilayers (PEM) built by layer-by-layer technique have been extensively studied over the last years, resulting in a wide variety of current and potential applications. This technique can be used to construct thin films with different functionalities, or to functionalize surfaces with substantial different properties of those of the underlying substrates. The multilayering process is achieved by the alternate adsorption of oppositely charged polyelectrolytes. In this work we get advantage of the protein resistant property of the Poly (l-lysine)-graft-(polyethyleneglycol) to create protein patterns. Proteins can be immobilized on a surface by unspecific physical adsorption, covalent binding or through specific interactions. The first protein used in this work was laccase, a copper-containing redox enzyme that catalyse the oxidation of a broad range of polyphenols and aromatic substrates, coupled to the reduction of O2 to H2O without need of cofactors. Applications of laccases have been reported in food, pulp, paper, and textile industry, and also in biosensor development. Some uses require the immobilization of the enzyme on solid supports by adsorption, covalent attachment, entrapment, etc, on several substrates. Especially for biosensor development, highly active, stable and reproducible immobilization of laccase is required.

Characterization of the Performance of Optical Label-Free Biosensors

The field of optical label free biosensors has become a topic of interest during past years, with devices based on the detection of angular or wavelength shift of optical modes [1]. Common parameters to characterize their performance are the Limit of Detection (LOD, defined as the minimum change of refractive index upon the sensing surface that the device is able to detect, and also BioLOD, which represents the minimum amount of target analyte accurately resolved by the system; with units of concentration (common un its are p pm, ng/ml, or nM). LOD gives a first value to compare different biosensors, and is obtained both theoretically (using photonic calculation tools), and experimentally,covering the sensing area with fluids of different refractive indexes.

Development and fabrication of optical biosensors based on biophotonic sensing cells (BICELLs)

El objetivo de esta tesis es el desarrollo y caracterización de biosensores ópticos sin marcado basados en celdas sensoras biofotónicas (BICELLs). Éstas son un nuevo concepto de biosensor desarrollado por el grupo de investigación y consiste en la combinación de técnicas de interrogación vertical, junto a estructuras fotónicas producidas usando métodos de micro- y nanofabricación. Varias conclusiones son extraídas de este trabajo. La primera, que se ha definido una BICELL estándar basada en interferómetros Fabry-Perot (FP). Se ha demostrado su capacidad para la comparación de rendimiento entre BICELLs estructuradas y para la realización de inmunoensayos de bajo coste. Se han estudiado diferentes técnicas de fabricación disponibles para la producción de BICELLs. Se determinó que la litografía de contacto a nivel de oblea produce estructuras de bajo coste, reproducibles y de alta calidad. La resolución alcanzada ha sido de 700 nm. El estudio de la respuesta a inmunoensayos de las BICELLs producidas se ha desarrollado en este trabajo. Se estudió la influencia de BICELLs basadas en diferentes geometrías y tamaños. De aquí resulta un nuevo enfoque para predecir el comportamiento de respuesta para la detección biológica de cualquier biosensor óptico estructurado, relacionando su superficie efectiva y su sensibilidad óptica. También se demostró una técnica novedosa y de bajo coste para la caracterización experimental de la sensibilidad óptica, basada en el depósito de películas ultradelgadas. Finalmente, se ha demostrado el uso de BICELLs desarrolladas en esta tesis, en la detección de aplicaciones reales, tales como hormonas, virus y proteínas. ABSTRACT The objective of this thesis is the development and characterization of optical label-free biosensors based on Bio-Photonic sensing Cells (BICELLs). BICELL is a novel biosensor concept developed by the research group, and it consists of a combination of vertical interrogation optical techniques and photonic structures produced by using micro- and nano-fabrication methods. Several main conclusions are extracted from this work. Firstly, a standard BICELL is defined based on FP interferometers, which demonstrated its capacity for accomplishing performance comparisons among different structured BICELLs, as well as to achieve low-cost immunoassays. Different available fabrication techniques were studied for BICELL manufacturing. It is found that contact lithography at wafer scale produce cost-effective, reproducible and high quality structures. The resolution achieved was 700 nm. Study on the response of developed BICELLs to immunoassays is performed within this work. It is therefore studied the influence of BICELLs based on different geometries and sizes in the immunoassay, which resulted in a new approach to predict the biosensing behaviour of any structured optical biosensor relating to its effective surface and optical sensitivity. Also, it is demonstrated a novel and low-cost characterization technique of the experimental optical sensitivity, based on ultrathin-film deposition. Finally, it is also demonstrated the capability of using the developed BICELLs in this thesis for real applications detection of hormones, virus and proteins.

High sensitivity biosensors based on shear mode AIN resonators for in liquid operation

El diagnóstico y detección temprana de enfermedades son clave para reducir la tasa de mortalidad, las hospitalizaciones de larga duración y el desaprovechamiento de recursos. En los últimos años se ha impulsado, mediante un aumento de la financiación, el desarrollo de nuevos biosensores de bajo coste capaces de detectar y cuantificar cantidades muy pequeñas de especies biológicas de una forma barata y sencilla. El trabajo presentado en esta Tesis Doctoral describe la investigación llevada a cabo en el desarrollo de sensores gravimétricos basados en resonadores de ondas acústicas de volumen (BAW) de estructura maciza (SMR). Los dispositivos emplean películas delgadas de A1N como material piezoeléctrico y operan en modo de cizalladura, para así poder detectar especies biológicas en medio líquido. El principio de funcionamiento de estos sensores se basa en la variación que experimenta la frecuencia de resonancia al quedar una pequeña masa adherida a su superficie. Necesitan operar en modo de cizalladura para que su resonancia no se atenúe al trabajar en medio líquido, así como ofrecer una superficie capaz de ser funcionalizada específicamente para la especie biológica a detectar. El reto planteado en esta tesis requiere un acercamiento pluridisciplinar al problema que incluye el estudio de los diferentes materiales que constituyen la estructura multicapa que forma un SMR, el diseño y fabricación del dispositivo y del sistema de fluídica, la funcionalización bioquímica de la superficie del sensor, la demostración de la capacidad de detección de especies biológicas y finalmente el diseño y fabricación de la electrónica asociada para la detección de la señal eléctrica. Todas esas tareas han sido abordadas en las distintas etapas del desarrollo de esta tesis y las contribuciones más relevantes se describen en el documento. En el campo de desarrollo de los materiales, se propone un proceso en dos etapas para la pulverización reactiva de capas de A1N que contengan microcristales inclinados capaces de excitar el modo de cizalladura. Se caracteriza la velocidad acústica del modo de cizalladura en todos los materiales que componen la estructura, con el fin de poder obtener un diseño más adecuado del reflector acústico. Se propone un nuevo tipo de material aislante de alta impedancia acústica consistente en capas de W03 pulverizadas que presenta ciertas ventajas tecnológicas frente a las capas convencionales de Ta205. Respecto del diseño del transductor, se estudia la influencia que tienen los con tactos eléctricos extendidos del resonador necesarios para poder adaptar el sistema de fluídica a la estructura. Los resultados indican que es necesario trabajar sobre sustratos aislantes (tanto el soporte como el espejo acústico) para evitar efectos parásitos asociados al uso de capas metálicas bajo los electrodos del resonador que dañan su resonancia. Se analiza la influencia de las diferentes capas del dispositivo en el coeficiente de temperatura de la frecuencia (TCF) del resonador llegando a la conclusión de que las dos últimas capas del reflector acústico afectan significativamente al TCF del SMR, pudiendo reducirse ajusfando adecuadamente sus espesores. De acuerdo con los resultados de estos estudios, se han diseñado finalmente resonadores SMR operando a f .3 GHz en modo de cizalladura, con un área activa de 65000 /xm2, contactos eléctricos que se extienden f .7 mm y factores de calidad en líquido de f 50. Las extensiones eléctricas permiten adaptar el resonador a un sistema de fluídica de metacrilato. Para la detección de especies biológicas se realiza un montaje experimental que permite circular 800 ¡A por la superficie del sensor a través de un circuito cerrado que trabaja a volumen constante. La circulación de soluciones iónicas sobre el sensor descubierto pone de manifiesto que las altas frecuencias de operación previenen los cortocircuitos y por tanto el aislamiento de los electrodos es prescindible. Se desarrolla un protocolo ad-hoc de funcionalización basado en el proceso estándar APTESGlutaraldehído. Se proponen dos alternativas novedosas para la funcionalización de las áreas activas del sensor basadas en el uso de capas de oxidación de Ir02 y su activación a través de un plasma de oxígeno que no daña al dispositivo. Ambos procesos contribuyen a simplificar notablemente la funcionalización de los sensores gravimétricos. Se utilizan anticuerpos y aptámeros como receptores para detectar trombina, anticuerpo monoclonal IgG de ratón y bacteria sonicadas. Una calibración preliminar del sensor con depósitos de capas finas de Si02 de densidad y espesor conocidos permite obtener una sensibilidad de 1800 kHz/pg-cm2 y un límite de detección of 4.2 pg. Finalmente se propone el prototipo de un circuito electrónico de excitación y lectura de bajo coste diseñado empleando teoría de circuitos de microondas. Aunque su diseño y funcionamiento admite mejoras, constituye la última etapa de un sistema completo de bajo coste para el diagnóstico de especies biológicas basado en resonadores SMR de A1N. ABSTRACT Early diagnosis and detection of diseases are essential for reducing mortality rate and preventing long-term hospitalization and waste of resources. These requirements have boosted the efforts and funding on the research of accurate and reliable means for detection and quantification of biological species, also known as biosensors. The work presented in this thesis describes the development and fabrication of gravimetric biosensors based on piezoelectric AlN bulk acoustic wave (BAW) solidly mounted resonators (SMRs) for detection of biological species in liquid media. These type of devices base their sensing principles in the variation that their resonant frequency suffers when a mass is attached to their surface. They need to operate in the shear mode to maintain a strong resonance in liquid and an adequate functionalisation of their sensing area to guarantee that only the targeted molecules cause the shift. The challenges that need to be overcome to achieve piezoelectric BAW resonators for high sensitivity detection in fluids require a multidisciplinary approach, that include the study of the materials involved, the design of the device and the fluidic system, the biochemical functionalisation of the active area, the experimental proof-of-concept with different target species and the design of an electronic readout circuit. All this tasks have been tackled at different stages of the thesis and the relevant contributions are described in the document. In the field of materials, a two-stage sputtering deposition process has been developed to obtain good-quality AlN films with uniformly tilted grains required to excite the shear mode. The shear acoustic velocities of the materials composing the acoustic reflector have been accurately studied to ensure an optimum design of the reflector stack. WO3 sputtered films have been proposed as high acoustic impedance material for insulating acoustic reflectors. They display several technological advantages for the processing of the resonators. Regarding the design, a study of the influence of the electrical extensions necessary to fit a fluidic system on the performance of the devices has been performed. The results indicate that high resistivity substrates and insulating reflectors are necessary to avoid the hindering of the resonance due to the parasitic effects induced by the extensions. The influence of the different layers of the stack on the resultant TCF of the SMRs has also been investigated. The two layers of the reflector closer to the piezoelectric layer have a significant influence on the TCF, which can be reduced by modifying their thicknesses accordingly. The data provided by these studies has led to the final design of the devices, which operate at 1.3 GHz in the shear mode and display an active area of 65000 /xm2 and electrical extensions of 1.7 mm while keeping a Qahear=150 in liquid. The extensions enable to fit a custom-made fluidic system made of methacrylate. To perform the biosensing experiments, an experimental setup with a liquid closed circuit operating at constant flow has been developed. Buffers of ionic characteristics have been tested on non-isolated devices, revealing that high operation frequencies prevent the risk of short circuit. An ad-hoc functionalisation protocol based on the standard APTES - Glutaraldehyde process has been developed. It includes two new processes that simplify the fabrication of the transducers: the use of IrO2 as oxidation layer and its functionalisation through an O2 plasma treatment that does not damage the resonators. Both antibodies and aptamers are used as receptors. In liquid sensing proof-of-concept experiments with thrombin, IgG mouse monoclonal antibody and sonicated bacteria have been displayed. A preliminary calibration of the devices using SiO2 layers reveals a sensitivity of 1800 kHz/pg-cm2 and a limit of detection of 4.2 pg. Finally, a first prototype of a low-cost electronic readout circuit designed using a standard microwave approach has been developed. Although its performance can be significantly improved, it is an effective first approach to the final stage of a portable low-cost diagnostic system based on shear mode AlN SMRs.

AlN-based BAW resonators with CNT electrodes for gravimetric biosensing

Solidly mounted resonators (SMRs) with a top carbon nanotubes (CNTs) surface coating that doubles as an electrode and as a sensing layer have been fabricated. The influence of the CNTs on the frequency response of the resonators was studied by direct comparison to identical devices with a top metallic electrode. It was found that the CNTs introduced significantly less mass load on the resonators and these devices exhibited a greater quality factor, Q (>2000, compared to ∼1000 for devices with metal electrodes), which increases the gravimetric sensitivity of the devices by allowing the tracking of smaller frequency shifts. Protein solutions with different concentrations were loaded on the top of the resonators and their responses to mass-load from physically adsorbed coatings were investigated. Results show that resonators using CNTs as the top electrode exhibited a higher frequency change for a given load (∼0.25 MHz cm2 ng−1) compared to that of a metal thin film electrode (∼0.14 MHz cm2 ng−1), due to the lower mass of the CNTelectrodes and their higher active surface area compared to that of a thin film metal electrode. It is therefore concluded that the use of CNTelectrodes on resonators for their use as gravimetric biosensors is a significant improvement over metallic electrodes that are normally employed.

Solidly Mounted Resonators with Carbon Nanotube Electrodes for Biosensing Applications

The work reported here shows a direct experimental comparison of the sensitivities of AlN solidly mounted resonators (SMR)-based biosensors fabricated with standard metal electrodes and with carbon nanotube electrodes. SMRs resonating at frequencies around 1.75 GHz have been fabricated, some devices using a thin film of multi-wall carbon nanotubes (CNTs) as the top electrode material and some identical devices using a chromium/gold electrode. Protein solutions with different concentrations were loaded on the top of the resonators and their responses to mass-load from physically adsorbed coatings were investigated. Results show that resonators using CNTs as the top electrode material exhibited higher frequency change for a given load due to the higher active surface area of a thin film of interconnecting CNTs compared to that of a metal thin film electrode and hence exhibited greater mass loading sensitivity. It is therefore concluded that the use of CNT electrodes on resonators for their use as gravimetric biosensors is viable and worthwhile.

Development of an electrochemical maltose biosensor

In this work, electrochemical maltose biosensors based on mutants of the maltose binding protein (MBP) are developed. A ruthenium II complex (Ru II ), which is covalently attached to MBP, serves as an electrochemical reporter of MBP conformational changes. Biosensors were made through direct attachment of Ru II complex modified MBP to gold electrode surfaces. The responses of some individual mutants were evaluated using square wave voltammetry. A maltose-dependent change in Faradic current and capacitance was observed. It is therefore demonstrated that biosensors using generically this family of bacterial periplasmic binding proteins (bPBP) can be made lending themselves to facile biorecognition element preparation and low cost electrochemical transduction.

Biomolecular interaction analysis of gestrinone-anti-gestrinone using arrays of high aspect ratio SU-8 nanopillars

In this paper, label-free biosensing for antibody screening by periodic lattices of high-aspect ratio SU-8 nano-pillars (BICELLs) is presented. As a demonstration, the determination of anti-gestrinone antibodies from whole rabbit serum is carried out, and for the first time, the dissociation constant (KD = 6 nM) of antigen-antibody recognition process is calculated using this sensing system. After gestrinone antigen immobilization on the BICELLs, the immunorecognition was performed. The cells were interrogated vertically by using micron spot size Fourier transform visible and IR spectrometry (FT-VIS-IR), and the dip wavenumber shift was monitored. The biosensing assay exhibited good reproducibility and sensitivity (LOD = 0.75 ng/mL).

Nanoinformatics knowledge infrastructures: bringing efficient information management to nanomedical research

Nanotechnology represents an area of particular promise and significant opportunity across multiple scientific disciplines. Ongoing nanotechnology research ranges from the characterization of nanoparticles and nanomaterials to the analysis and processing of experimental data seeking correlations between nanoparticles and their functionalities and side effects. Due to their special properties, nanoparticles are suitable for cellular-level diagnostics and therapy, offering numerous applications in medicine, e.g. development of biomedical devices, tissue repair, drug delivery systems and biosensors. In nanomedicine, recent studies are producing large amounts of structural and property data, highlighting the role for computational approaches in information management. While in vitro and in vivo assays are expensive, the cost of computing is falling. Furthermore, improvements in the accuracy of computational methods (e.g. data mining, knowledge discovery, modeling and simulation) have enabled effective tools to automate the extraction, management and storage of these vast data volumes. Since this information is widely distributed, one major issue is how to locate and access data where it resides (which also poses data-sharing limitations). The novel discipline of nanoinformatics addresses the information challenges related to nanotechnology research. In this paper, we summarize the needs and challenges in the field and present an overview of extant initiatives and efforts.

Efecto de la adición de ingredientes funcionales en el comportamiento reológico y la textura de puré de patata (Cv. Kennebec) fresco y congelado

El interés creciente en encontrar alimentos precocinados congelados que se asemejen a productos naturales, capaces de superar un procesado con el menor daño, ha generado un aumento en el estudio de nuevos productos en este campo de la investigación. Las características de cada matriz alimentaria, la composición y estructura de los ingredientes, así como el efecto de las interacciones entre ellos, modifica la textura, estructura y las propiedades físicas y sensoriales del alimento, así como su aceptación por el consumidor. En este contexto, la investigación realizada en esta tesis doctoral se ha llevado a cabo en puré de patata considerado como una matriz alimentaria semisólida y se ha centrado en analizar los efectos de la concentración y modificación de la composición en las propiedades reológicas y de textura, en las propiedades físico-químicas y estructurales, así como en los atributos sensoriales de los purés de patata cuando a estos se le añaden diferentes ingredientes funcionales como fibra de guisante, inulina, aceite de oliva, aislado de proteína de soja, ácidos grasos omega 3 y/o sus mezclas. Para ello, se han realizado cuatro estudios donde se determinan las propiedades reológicas mediante ensayos dinámicos oscilatorios y en estado estacionario, los parámetros instrumentales de textura mediante ensayos de extrusión inversa y de penetración cónica, además de los cambios estructurales a través de cromatografía iónica con detector de pulsos amperométrico, cromatografía de gases con detector de ionización de llama y microscopía electrónica de barrido. Conjuntamente, se han evaluado los atributos sensoriales de los diferentes purés generando los descriptores que mejor definen la calidad sensorial del producto, utilizando un panel de jueces entrenados y valorándose la aceptación global de los nuevos productos mediante un panel de consumidores. En un primer estudio, el puré de patata natural congelado elaborado con crioprotectores se enriqueció con fibra dietética insoluble (fibra de guisante), fibra dietética soluble (inulina) y sus mezclas. La fibra de guisante influyó significativa y negativamente en la textura del puré de patata, percibiéndose en el producto un incremento de la dureza y de la arenosidad, mientras que la inulina produjo un ablandamiento del sistema. En un segundo estudio, el puré de patata natural fresco y congelado/descongelado elaborado con y sin crioprotectores, se enriqueció con fibra dietética soluble (inulina), aceite de oliva virgen extra y sus mezclas. La adición de estos dos ingredientes generó un ablandamiento de la matriz del sistema, produciéndose, sin embargo, un efecto sinérgico entre ambos ingredientes funcionales. La inulina tuvo un efecto más significativo en la viscosidad aparente del producto, mientras que el aceite de oliva virgen extra afectó más significativamente a la pseudoplasticidad, al índice de consistencia y a la viscosidad plástica del mismo. El proceso de congelación y descongelación utilizado favoreció la reducción del tamaño de las partículas de inulina haciéndolas imperceptibles al paladar, obteniéndose productos más cremosos y con mayor aceptabilidad global que sus homólogos frescos. En un tercer estudio, el puré de patata natural fresco y congelado/descongelado elaborado con crioprotectores se enriqueció con mezclas de fibra dietética soluble (inulina) y aislado de proteína de soja. Los resultados demostraron que el ciclo de congelación y descongelación realizado no afecta el grado de polimerización de la inulina. La estructura química de la inulina tampoco se vio afectada por la incorporación de la soja. El proceso de congelación/descongelación, así como la adición de concentraciones altas de inulina y bajas de aislado de proteína de soja, favorecen la disminución de la contribución de la componente viscosa en las propiedades viscoelásticas del puré de patata. La cremosidad fue el único atributo sensorial que presentó una correlación lineal significativa entre las puntuaciones otorgadas por panelistas entrenados y no entrenados. Por último, se elaboró un puré de patata natural fresco y congelado/descongelado optimizado con crioprotectores y enriquecido con la suma de ácido docosahexaenoico (DHA, C22:6 n-3) y ácido eicosapentaenoico (EPA, C20:5 n-3) y con ácido α-linolénico (ALA, C18:3 n-3) microencapsulados. El ciclo de congelación y descongelación no afectó al perfil de ácidos grasos del puré de patata. La adición de omega 3 procedente de aceites de lino y pescado microencapsulados mejora los indicadores nutricionales que definen la calidad de la grasa, obteniéndose un producto más saludable. ABSTRACT The growing interest in finding frozen precooked products that are like a natural product and capable of withstanding initial processing with minimum damage and remaining stable during preservation and reheating prior to consumption has generated an increase in studies of new products in this field of research. The characteristics of each food matrix, the composition and structure of the ingredients and the effect of interactions between them alter the texture, structure and physical and sensory properties of the food product and its acceptance by the consumer. In this context, the research conducted in this doctoral thesis was carried out on mashed potato, considered as a semi-solid food matrix, and focused on analysing the effects of concentration and modification of the composition of the mashed potato matrix on the rheological and textural properties, physicochemical and structural properties and sensory attributes of mashed potato when various functional ingredients are added to it, such as pea fibre, inulin, olive oil, soy protein isolate, omega 3 fatty acids and/or mixtures of these ingredients. Four studies were conducted for this purpose. Rheological properties were determined by oscillatory dynamic tests and stationary state tests, and instrumental texture parameters by backward extrusion and cone penetration tests. Structural changes were studied by ion chromatography with pulsed amperometric detector, gas chromatography with flame ionisation detector and scanning electron microscopy. The sensory attributes of the various mashed potato mixtures were evaluated by generating the descriptors that best defined the sensory quality of the products and using a panel of trained judges, and overall acceptance of the new products was evaluated by a panel of consumers. In the first study, frozen natural mashed potato incorporating cryoprotectants was enriched with insoluble dietary fibre (pea fibre), soluble dietary fibre (inulin) and mixtures of the two. Pea fibre had a significant negative influence on the texture of the mashed potato, producing an increase in hardness and granularity, whereas inulin produced a softening of the system. In the second study, fresh and frozen/thawed natural mashed potato prepared with and without cryoprotectants was enriched with soluble dietary fibre (inulin), extra virgin olive oil and mixtures of the two. The addition of these two ingredients generated softening of the matrix of the system, but a synergic effect between the two functional ingredients was produced. Inulin had a more significant effect on the apparent viscosity of the product, whereas extra virgin olive oil had a more significant effect on its pseudoplasticity, consistency index and plastic viscosity. The freezing and thawing process that was used contributed to a reduction in the size of the inulin particles, making them imperceptible to the palate and producing creamier products with greater overall acceptability than their fresh equivalents. In the third study, the fresh and frozen/thawed natural mashed potato incorporating cryoprotectants was enriched with mixtures of soluble dietary fibre (inulin) and soy protein isolate. The results showed that the freezing and thawing process that was performed did not affect the degree of polymerisation of the inulin. The chemical structure of the inulin was also not affected by the incorporation of soy. The freezing and thawing process and the addition of high concentrations of inulin and low concentrations of soy protein isolate favoured a decrease in the contribution of the viscous component to the viscoelastic properties of the mashed potato. Creaminess was the only sensory attribute that presented a significant linear correlation between the scores given by trained and untrained panellists. Lastly, fresh and frozen/thawed natural mashed potato optimised with cryoprotectants was prepared and enriched with the sum of docosahexaenoic acid (DHA, C22:6 n-3) and eicosapentaenoic acid (EPA, C20:5 n-3) and with α-linolenic acid (ALA, C18:3 n-3), microencapsulated. The freezing and thawing process did not affect the fatty acid profile of the mashed potato. The addition of omega 3 obtained from microencapsulated linseed and fish oils improved the nutritional indicators that define the quality of the fat, producing a healthier product.

Uncertainty in optical bio-sensors due to the spectral displacement of the interference modes of the transduction signal. Incertidumbre en bio-sensores ópticos asociada al desplazamiento espectral de los modos de interferencia de la señal de transducción

The analysis of the interference modes has an increasing application, especially in the field of optical biosensors. In this type of sensors, the displacement Δν of the interference modes of the transduction signal is observed when a particular biological agent is placed over the biosensor. In order to measure this displacement, the position of a maximum (or a minimum) of the signal must be detected before and after placing the agent over the sensor. A parameter of great importance for this kind of sensors is the period Pν of the signal, which is inversely proportional to the optical thickness h0 of the sensor in the absence of the biological agent. The increase of this period improves the sensitivity of the sensor but it worsens the detection of the maximum. In this paper, authors analyze the propagation of uncertainties in these sensors when using least squares techniques for the detection of the maxima (or minima) of the signal. Techniques described in supplement 2 of the ISO-GUM Guide are used. The result of the analysis allows a metrological educated answer to the question of which is the optimal period Pν of the signal. El análisis del comportamiento de los modos de interferencia tiene una aplicación cada vez más amplia, especialmente en el campo de los biosensores ópticos. En este tipo de sensores se observa el desplazamiento Δν de los modos de interferencia de la señal de transducción al reconocer un de-terminado agente biológico. Para medir ese desplazamiento se debe detectar la posición de un máximo o mínimo de la señal antes y después de dicho desplazamiento. En este tipo de biosensores un parámetro de gran importancia es el periodo Pν de la señal el cual es inversamente proporcional al espesor óptico h0 del sensor en ausencia de agente biológico. El aumento de dicho periodo mejora la sensibilidad del sensor pero parece dificultar la detección del mínimo o máximo. Por tanto, su efecto sobre la incertidumbre del resultado de la medida presenta dos efectos contrapuestos: la mejora de la sensibilidad frente a la dificultad creciente en la detección del mínimo ó máximo. En este trabajo, los autores analizan la propagación de incertidumbres en estos sensores utilizando herramientas de ajuste por MM.CC. para la detección de los mínimos o máximos de la señal y técnicas de propagación de incertidumbres descritas en el suplemento 2 de la Guía ISO-GUM. El resultado del análisis permite dar una respuesta, justificada desde el punto de vista metrológico, de en que condiciones es conveniente o no aumentar el periodo Pν de la señal.

Silicon nanopillar arrays with SiO2 overlayer for biosensing application

We present the fabrication of silicon dioxide (SiO2) coated silicon nanopillar array structures and demonstrate their application as sensitive optical biosensors. Colloidal lithography, plasma dry etching and deposition processes are used to fabricate SiO2 coated Si nanopillar arrays with two different diameters and periods. Proof of concept bio recognition experiments are carried out with the bovine serum albumin (BSA)/antiBSA model system using Fourier transform visible and IR spectrometry (FT-VIS-IR) in reflection mode. A limit of detection (LoD) value of 5.2 ng/ml is estimated taking in to account the wavenumber uncertainty in the measurements.

Caracterización y optimización de estructuras biofotónicas y técnicas avanzadas de interrogación para desarrollo de biosensores ópticos

El núcleo fundamental de esta tesis doctoral es un modelo teórico de la interacción de la luz con un tipo particular de biosensor óptico. Este biosensor se compone de dos regiones: en la región inferior puede haber capas de materiales con diferentes espesores y propiedades ópticas, apiladas horizontalmente; en la zona superior, sobre la que incide directamente el haz de luz, puede haber estructuras que hacen que las propiedades ópticas cambien tanto en el plano horizontal como en la dirección vertical. Estos biosensores responden ópticamente de forma diferente al ser iluminados dependiendo de que su superficie externa esté, en mayor o menor medida, recubierta con diferentes tipos de material biológico. En esta tesis se define un modelo analítico aproximado que permite simular la respuesta óptica de biosensores con estructuras en su región más externa. Una vez comprobada la validez práctica del modelo mediante comparación con medidas experimentales, éste se utiliza en el diseño de biosensores de rendimiento óptimo y en la definición de nuevas técnicas de interrogación óptica. En particular, el sistema de transducción IROP (Increased Relative Optical Power), basado en el efecto que produce la presencia de material biológico, en la potencia total reflejada por la celda biosensora en determinados intervalos espectrales, es uno de los sistemas que ha sido patentado y es objeto de desarrollo por la empresa de base tecnológica BIOD [www.biod.es/], estando ya disponibles en este momento varios dispositivos de diagnóstico basados en esta idea. Los dispositivos basados en este sistema de transducción han demostrado su eficiencia en la detección de proteínas y agentes infecciosos como los rotavirus y el virus del dengue. Finalmente, el modelo teórico desarrollado se utiliza para caracterizar las propiedades ópticas de algunos de los materiales de los que se fabrican los biosensores, así como las de las capas de material biológico formadas en las diferentes fases de un inmunoensayo. Los parámetros ópticos de las capas mencionadas se obtienen mediante el método general de ajuste por mínimos cuadrados a las curvas experimentales obtenidas en los inmunoensayos. ABSTRACT The core of this thesis is the theoretical modeling of the interaction of light with a particular type of optical biosensor. This biosensor consists of two parts: in the lower region may have layers of materials with different thicknesses and optical properties, stacked horizontally; at the top, on which directly affects the light beam, there may be structures that make optical properties change in both, the horizontal and in the vertical direction. These biosensors optically respond differently when illuminated depending on its external surface is greater or lesser extent, coated with different types of biological material. In this thesis an approximate analytical model to simulate the optical response of biosensors with structures in its outer region is defined. After verifying the practical validity of the model by comparison with experimental measurements, it is used in the design of biosensors with optimal performance and the definition of new optical interrogation techniques. In particular, the transduction system IROP (Increased Relative Optical Power) based on the effect of the presence of biological material in the total power reflected from the biosensor cell in certain spectral ranges, has been patented and is under development by the startup company BIOD [www.biod.es/], being already available at this time, several diagnostic devices based on this idea. Devices based on this transduction system have proven their efficiency in detecting proteins and infectious agents such as rotavirus and virus of dengue. Finally, the developed theoretical model is used to characterize the optical properties of some of the materials from which biosensors are fabricated, as well as the optical properties of the biological material layers formed at different stages of an immunoassay. The optical parameters of the layers above are obtained by the general method of least squares fit to the experimental curves obtained in immunoassays.

Aluminum nanoholes for optical biosensing

Sub-wavelength diameter holes in thin metal layers can exhibit remarkable optical features that make them highly suitable for (bio)sensing applications. Either as efficient light scattering centers for surface plasmon excitation or metal-clad optical waveguides, they are able to form strongly localized optical fields that can effectively interact with biomolecules and/or nanoparticles on the nanoscale. As the metal of choice, aluminum exhibits good optical and electrical properties, is easy to manufacture and process and, unlike gold and silver, its low cost makes it very promising for commercial applications. However, aluminum has been scarcely used for biosensing purposes due to corrosion and pitting issues. In this short review, we show our recent achievements on aluminum nanohole platforms for (bio)sensing. These include a method to circumvent aluminum degradation—which has been successfully applied to the demonstration of aluminum nanohole array (NHA) immunosensors based on both, glass and polycarbonate compact discs supports—the use of aluminum nanoholes operating as optical waveguides for synthesizing submicron-sized molecularly imprinted polymers by local photopolymerization, and a technique for fabricating transferable aluminum NHAs onto flexible pressure-sensitive adhesive tapes, which could facilitate the development of a wearable technology based on aluminum NHAs.