Robust control of underactuated wheeled mobile manipulators using GPI disturbance observers

This article describes the design of a linear observer–linear controller-based robust output feedback scheme for output reference trajectory tracking tasks in the case of nonlinear, multivariable, nonholonomic underactuated mobile manipulators. The proposed linear feedback scheme is based on the use of a classical linear feedback controller and suitably extended, high-gain, linear Generalized Proportional Integral (GPI) observers, thus aiding the linear feedback controllers to provide an accurate simultaneous estimation of each flat output associated phase variables and of the exogenous and perturbation inputs. This information is used in the proposed feedback controller in (a) approximate, yet close, cancelations, as lumped unstructured time-varying terms, of the influence of the highly coupled nonlinearities, and (b) the devising of proper linear output feedback control laws based on the approximate estimates of the string of phase variables associated with the flat outputs simultaneously provided by the disturbance observers. Simulations reveal the effectiveness of the proposed approach.

Magnetic Attitude Control System for a Small Satellite. Impact on the Thermal Performance

El principal objetivo de la tesis es estudiar el acoplamiento entre los subsistemas de control de actitud y de control térmico de un pequeño satélite, con el fin de buscar la solución a los problemas relacionados con la determinación de los parámetros de diseño. Se considera la evolución de la actitud y de las temperaturas del satélite bajo la influencia de dos estrategias de orientación diferentes: 1) estabilización magnética pasiva de la orientación (PMAS, passive magnetic attitude stabilization), y 2) control de actitud magnético activo (AMAC, active magnetic attitude control). En primer lugar se presenta el modelo matemático del problema, que incluye la dinámica rotacional y el modelo térmico. En el problema térmico se considera un satélite cúbico modelizado por medio de siete nodos (seis externos y uno interno) aplicando la ecuación del balance térmico. Una vez establecido el modelo matemático del problema, se estudia la evolución que corresponde a las dos estrategias mencionadas. La estrategia PMAS se ha seleccionado por su simplicidad, fiabilidad, bajo coste, ahorrando consumo de potencia, masa coste y complejidad, comparado con otras estrategias. Se ha considerado otra estrategia de control que consigue que el satélite gire a una velocidad requerida alrededor de un eje deseado de giro, pudiendo controlar su dirección en un sistema inercial de referencia, ya que frecuentemente el subsistema térmico establece requisitos de giro alrededor de un eje del satélite orientado en una dirección perpendicular a la radiación solar incidente. En relación con el problema térmico, para estudiar la influencia de la velocidad de giro en la evolución de las temperaturas en diversos puntos del satélite, se ha empleado un modelo térmico linealizado, obtenido a partir de la formulación no lineal aplicando un método de perturbaciones. El resultado del estudio muestra que el tiempo de estabilización de la temperatura y la influencia de las cargas periódicas externas disminuye cuando aumenta la velocidad de giro. Los cambios de temperatura se reducen hasta ser muy pequeños para velocidades de rotación altas. En relación con la estrategia PMAC se ha observado que a pesar de su uso extendido entre los micro y nano satélites todavía presenta problemas que resolver. Estos problemas están relacionados con el dimensionamiento de los parámetros del sistema y la predicción del funcionamiento en órbita. Los problemas aparecen debido a la dificultad en la determinación de las características magnéticas de los cuerpos ferromagnéticos (varillas de histéresis) que se utilizan como amortiguadores de oscilaciones en los satélites. Para estudiar este problema se presenta un modelo analítico que permite estimar la eficiencia del amortiguamiento, y que se ha aplicado al estudio del comportamiento en vuelo de varios satélites, y que se ha empleado para comparar los resultados del modelo con los obtenidos en vuelo, observándose que el modelo permite explicar satisfactoriamente el comportamiento registrado. ABSTRACT The main objective of this thesis is to study the coupling between the attitude control and thermal control subsystems of a small satellite, and address the solution to some existing issues concerning the determination of their parameters. Through the thesis the attitude and temperature evolution of the satellite is studied under the influence of two independent attitude stabilization and control strategies: (1) passive magnetic attitude stabilization (PMAS), and (2) active magnetic attitude control (AMAC). In this regard the mathematical model of the problem is explained and presented. The mathematical model includes both the rotational dynamics and the thermal model. The thermal model is derived for a cubic satellite by solving the heat balance equation for 6 external and 1 internal nodes. Once established the mathematical model of the problem, the above mentioned attitude strategies were applied to the system and the temperature evolution of the 7 nodes of the satellite was studied. The PMAS technique has been selected to be studied due to its prevalent use, simplicity, reliability, and cost, as this strategy significantly saves the overall power, weight, cost, and reduces the complexity of the system compared to other attitude control strategies. In addition to that, another control law that provides the satellite with a desired spin rate along a desired axis of the satellite, whose direction can be controlled with respect to the inertial reference frame is considered, as the thermal subsystem of a satellite usually demands a spin requirement around an axis of the satellite which is positioned perpendicular to the direction of the coming solar radiation. Concerning the thermal problem, to study the influence of spin rate on temperature evolution of the satellite a linear approach of the thermal model is used, which is based on perturbation theory applied to the nonlinear differential equations of the thermal model of a spacecraft moving in a closed orbit. The results of this study showed that the temperature stabilization time and the periodic influence of the external thermal loads decreases by increasing the spin rate. However, the changes become insignificant for higher values of spin rate. Concerning the PMAS strategy, it was observed that in spite of its extended application to micro and nano satellites, still there are some issues to be solved regarding this strategy. These issues are related to the sizing of its system parameters and predicting the in-orbit performance. The problems were found to be rooted in the difficulties that exist in determining the magnetic characteristics of the ferromagnetic bodies (hysteresis rods) that are applied as damping devices on-board satellites. To address these issues an analytic model for estimating their damping efficiency is proposed and applied to several existing satellites in order to compare the results with their respective in-flight data. This model can explain the behavior showed by these satellites.

PWM Control of a Buck Converter with an Amorphous Core Coil

Pulse-width modulation is widely used to control electronic converters. One of the most topologies used for high DC voltage/low DC voltage conversion is the Buck converter. It is obtained as a second order system with a LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core instead of air core lets design converters with smaller size. If high switching frequencies are used for obtaining high quality voltage output, the value of the auto inductance L is reduced throughout the time. Then, robust controllers are needed if the accuracy of the converter response must not be affected by auto inductance and load variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a not-toohigh switching frequency is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results are presented.

Space-state robust control of a Buck converter with amorphous core coil and variable load

Pulse-width modulation is widely used to control electronic converters. One of the most frequently used topologies for high DC voltage/low DC voltage conversion is the Buck converter. These converters are described by a second order system with an LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core rather than an air core permits the design of smaller converters. If high switching frequencies are used to obtain high quality voltage output, then the value of the auto inductance L is reduced over time. Robust controllers are thus needed if the accuracy of the converter response must be preserved under auto inductance and payload variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a switching frequency that is not too high is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results and a comparison with a standard PID controller are also presented.

Jovian Capture of a Spacecraft with a Self-Balanced Electrodynamic Bare Tether

This paper proposes and analyzes the use of a nonrotating tethered system for a direct capture in Jovian orbit using the electrodynamic force generated along the cable. A detailed dynamical model is developed showing a strong gravitational and electrodynamic coupling between the center of mass and the attitude motions. This paper shows the feasibility of a direct capture in Jovian orbit of a rigid tethered system preventing the tether from rotating. Additional mechanical–thermal requirements are explored, and preliminary operational limits are defined to complete the maneuver. In particular, to ensure that the system remains nonrotating, a nominal attitude profile for a self-balanced electrodynamic tether is proposed, as well as a simple feedback control.

Estimación del consumo de potencia en un terminal portátil multimedia basada en la PMU del procesador

Este proyecto se incluye en una línea de trabajo que tiene como objetivo final la optimización de la energía consumida por un dispositivo portátil multimedia mediante la aplicación de técnicas de control realimentado, a partir de una modificación dinámica de la frecuencia de trabajo del procesador y de su tensión de alimentación. La modificación de frecuencia y tensión se realiza a partir de la información de realimentación acerca de la potencia consumida por el dispositivo, lo que supone un problema ya que no suele ser posible la monitorización del consumo de potencia en dispositivos de estas características. Este es el motivo por el que se recurre a la estimación del consumo de potencia, utilizando para ello un modelo de predicción. A partir del número de veces que se producen ciertos eventos en el procesador del dispositivo, el modelo de predicción es capaz de obtener una estimación de la potencia consumida por dicho dispositivo. El trabajo llevado a cabo en este proyecto se centra en la implementación de un modelo de estimación de potencia en el kernel de Linux. La razón por la que la estimación se implementa en el sistema operativo es, en primer lugar para lograr un acceso directo a los contadores del procesador. En segundo lugar, para facilitar la modificación de frecuencia y tensión, una vez obtenida la estimación de potencia, ya que esta también se realiza desde el sistema operativo. Otro motivo para implementar la estimación en el sistema operativo, es que la estimación debe ser independiente de las aplicaciones de usuario. Además, el proceso de estimación se realiza de forma periódica, lo que sería difícil de lograr si no se trabajase desde el sistema operativo. Es imprescindible que la estimación se haga de forma periódica ya que al ser dinámica la modificación de frecuencia y tensión que se pretende implementar, se necesita conocer el consumo de potencia del dispositivo en todo momento. Cabe destacar también, que los algoritmos de control se tienen que diseñar sobre un patrón periódico de actuación. El modelo de estimación de potencia funciona de manera específica para el perfil de consumo generado por una única aplicación determinada, que en este caso es un decodificador de vídeo. Sin embargo, es necesario que funcione de la forma más precisa posible para cada una de las frecuencias de trabajo del procesador, y para el mayor número posible de secuencias de vídeo. Esto es debido a que las sucesivas estimaciones de potencia se pretenden utilizar para llevar a cabo la modificación dinámica de frecuencia, por lo que el modelo debe ser capaz de continuar realizando las estimaciones independientemente de la frecuencia con la que esté trabajando el dispositivo. Para valorar la precisión del modelo de estimación se toman medidas de la potencia consumida por el dispositivo a las distintas frecuencias de trabajo durante la ejecución del decodificador de vídeo. Estas medidas se comparan con las estimaciones de potencia obtenidas durante esas mismas ejecuciones, obteniendo de esta forma el error de predicción cometido por el modelo y realizando las modificaciones y ajustes oportunos en el mismo. ABSTRACT. This project is included in a work line which tries to optimize consumption of handheld multimedia devices by the application of feedback control techniques, from a dynamic modification of the processor work frequency and its voltage. The frequency and voltage modification is performed depending on the feedback information about the device power consumption. This is a problem because normally it is not possible to monitor the power consumption on this kind of devices. This is the reason why a power consumption estimation is used instead, which is obtained from a prediction model. Using the number of times some events occur on the device processor, the prediction model is able to obtain a power consumption estimation of this device. The work done in this project focuses on the implementation of a power estimation model in the Linux kernel. The main reason to implement the estimation in the operating system is to achieve a direct access to the processor counters. The second reason is to facilitate the frequency and voltage modification, because this modification is also done from the operating system. Another reason to implement the estimation in the operating system is because the estimation must be done apart of the user applications. Moreover, the estimation process is done periodically, what is difficult to obtain outside the operating system. It is necessary to make the estimation in a periodic way because the frequency and voltage modification is going to be dynamic, so it needs to know the device power consumption at every time. Also, it is important to say that the control algorithms have to be designed over a periodic pattern of action. The power estimation model works specifically for the consumption profile generated by a single application, which in this case is a video decoder. Nevertheless, it is necessary that the model works as accurate as possible for each frequency available on the processor, and for the greatest number of video sequences. This is because the power estimations are going to be used to modify dynamically the frequency, so the model must be able to work independently of the device frequency. To value the estimation model precision, some measurements of the device power consumption are taken at different frequencies during the video decoder execution. These measurements are compared with the power estimations obtained during that execution, getting the prediction error committed by the model, and if it is necessary, making modifications and settings on this model.

Optimal Control Using Feedback Linearization for a Generalized T-S Model

In this paper, a fuzzy feedback linearization is used to control nonlinear systems described by Takagi-Suengo (T-S) fuzzy systems. In this work, an optimal controller is designed using the linear quadratic regulator (LQR). The well known weighting parameters approach is applied to optimize local and global approximation and modelling capability of T-S fuzzy model to improve the choice of the performance index and minimize it. The approach used here can be considered as a generalized version of T-S method. Simulation results indicate the potential, simplicity and generality of the estimation method and the robustness of the proposed optimal LQR algorithm.

Soporte de redes activas para un servicio integrado de multipunto fiable con control de congestión

Las limitaciones de las tecnologías de red actuales, identificadas en la Agencia de Proyectos de Investigación Avanzados para la Defensa (DARPA) durante 1995, han originado recientemente una propuesta de modelo de red denominado Redes Activas. En este modelo, los nodos proporcionan un entorno de ejecución sobre el que se ejecuta el código asociado a cada paquete. El objetivo es disponer de una tecnología de red que permita que nuevos servicios de red sean desarrollados e instalados rápidamente sin modificar los nodos de la red. Un servicio de red que se puede beneficiar de esta tecnología es la transmisión de datos en multipunto con diferentes grados fiabilidad. Las propuestas actuales de servicios de multipunto fiable proporcionan una solución específica para cada clase de aplicaciones, y los protocolos existentes extremo a extremo sufren de limitaciones técnicas relacionadas con una fiabilidad limitada, y con la ausencia de mecanismos de control de congestión efectivos. Esta tesis realiza propuestas originales conducentes a solucionar parte de las limitaciones actuales en el ámbito de Redes Activas y multipunto fiable con control de congestión. En primer lugar, se especificará un servicio genérico de multipunto fiable que, basándose en los requisitos de una serie de aplicaciones consideradas relevantes, proporcione diferentes clases de sesiones y grados de fiabilidad. Partiendo de la definición del servicio genérico especificado, se diseñará un protocolo de comunicaciones sobre la tecnología de Redes Activas que proporcione dicho servicio. El protocolo diseñado estará dotado de un mecanismo de control de congestión para que la fuente ajuste dinámicamente el tráfico inyectado a las condiciones de carga de la red. En esta tesis se pretende también profundizar en el estudio y análisis de la tecnología de Redes Activas, experimentando con dicha tecnología para proporcionar una realimentación a sus diseñadores. Dicha experimentación se realizará en tres ámbitos: el de los servicios y protocolos que puede soportar, el del modelo y arquitectura de las Redes Activas y el de las plataformas de ejecución disponibles. Como aportación adicional de este trabajo, se validarán los objetivos anteriores mediante una implementación piloto de las entidades de protocolo y de su interfaz de servicio sobre uno de los entornos de ejecución disponibles. Abstract The limitations of current networking technologies identified in the Defense Advance Research Projects Agency (DARPA) along 1995 have led to a recent proposal of a new network model called Active Networks. In this model, the nodes provide an execution environment over which the code used to process each packet is executed. The objective is a network technology that allows the fast design and deployment of new network services without requiring the modification of the network nodes. One network service that could benefit from this technology is the transmission of multicast data with different types of loss tolerance. The current proposals for reliable multicast services provide specific solutions for each application class, and existing end-to-end protocols suffer from technical drawbacks related to limited reliability and lack of an effective congestion control mechanism. This thesis contains original proposals that aim to solve part of the current drawbacks in the scope of Active Networks and reliable multicast with congestion control. Firstly, a generic reliable multicast network service will be specified. This service will be designed from the requirements of a relevant set of applications, and will provide different session classes and different types of reliability. Then, a network protocol based on Active Network technology will be designed such that it provides the specified network service. This protocol will incorporate a congestion control mechanism capable of performing an automatic adjustment of the traffic injected by the source to the available network capacity. This thesis will also contribute to a deeper study and analysis of Active Network technology, by experimenting with the technology in order to provide feedback to its designers. This experimentation will be done attending to three different scopes: support of Active Network for services and protocols, Active Network model and architecture, and currently available Active Network execution environments. As an additional contribution of this work, the previous objectives will be validated through a prototype implementation of the protocol entities and the service interface based on one of the current execution environments.

Dual-Band Tunable Recursive Active Filter

This letter presents a novel recursive active filter topology that provides dual-band performance, with independent tuning capability in both bands. The dual-band operation is achieved by using two independent feedback lines. Additionally, linear phase shifters based on left-handed cells are included in these two branches in order to tune the center frequency of both pass bands.

Non-linear Control of an Autonomous Ground Vehicle

In this paper, in order to select a speed controller for a specific non-linear autonomous ground vehicle, proportional-integral-derivative (PID), Fuzzy, and linear quadratic regulator (LQR) controllers were designed. Here, in order to carry out the tuning of the above controllers, a multicomputer genetic algorithm (MGA) was designed. Then, the results of the MGA were used to parameterize the PID, Fuzzy and LQR controllers and to test them under laboratory conditions. Finally, a comparative analysis of the performance of the three controllers was conducted.

A comparative study of SISO and MIMO control strategies for floor vibration damping

Civil engineering structures such as floor systems with open-plan layout or lightweight footbridges are susceptible to excessive level of vibrations caused by human loading. Active vibration control (AVC) via inertial mass actuators has been shown to be a viable technique to mitigate vibrations, allowing structures to satisfy vibration serviceability limits. Most of the AVC applications involve the use of SISO (single input single-output) strategies based on collocated control. However, in the case of floor structures, in which mostof the vibration modes are locally spatially distributed, SISO or multi-SISO strategies are quite inefficient. In this paper, a MIMO (multi-inputs multi-outputs) control in decentralised and centralised configuration is designed. The design process simultaneously finds the placement of multiple actuators and sensors and the output feedback gains. Additionally, actuator dynamics, actuator nonlinearities and frequency and time weightings are considered into the design process. Results with SISO and decentralised and centralised MIMO control (for a given number of actuators and sensors) are compared, showing the advantages of MIMO control for floor vibration control.

Adaptive Control for ZVS Three Phase Full Active Bridge Converter with ARCN

This paper presents an adaptive control for the auxiliary circuit, called ARCN (Auxiliary Resonant Commutating Network), used to achieve ZVS in full active bridge converters under a wide load range. Depending on the load conditions, the proposed control adapts the timing of the ARCN to minimize the losses. The principle of operation and implementation considerations are presented for a three phase full active bridge converter, proposing different methods to implement the control according to the specifications. The experimental results shown verify the proposed methodology.

Design and control of multi-finger haptic devices for dexterous manipulation

En la interacción con el entorno que nos rodea durante nuestra vida diaria (utilizar un cepillo de dientes, abrir puertas, utilizar el teléfono móvil, etc.) y en situaciones profesionales (intervenciones médicas, procesos de producción, etc.), típicamente realizamos manipulaciones avanzadas que incluyen la utilización de los dedos de ambas manos. De esta forma el desarrollo de métodos de interacción háptica multi-dedo dan lugar a interfaces hombre-máquina más naturales y realistas. No obstante, la mayoría de interfaces hápticas disponibles en el mercado están basadas en interacciones con un solo punto de contacto; esto puede ser suficiente para la exploración o palpación del entorno pero no permite la realización de tareas más avanzadas como agarres. En esta tesis, se investiga el diseño mecánico, control y aplicaciones de dispositivos hápticos modulares con capacidad de reflexión de fuerzas en los dedos índice, corazón y pulgar del usuario. El diseño mecánico de la interfaz diseñada, ha sido optimizado con funciones multi-objetivo para conseguir una baja inercia, un amplio espacio de trabajo, alta manipulabilidad y reflexión de fuerzas superiores a 3 N en el espacio de trabajo. El ancho de banda y la rigidez del dispositivo se han evaluado mediante simulación y experimentación real. Una de las áreas más importantes en el diseño de estos dispositivos es el efector final, ya que es la parte que está en contacto con el usuario. Durante este trabajo se ha diseñado un dedal de bajo peso, adaptable a diferentes usuarios que, mediante la incorporación de sensores de contacto, permite estimar fuerzas normales y tangenciales durante la interacción con entornos reales y virtuales. Para el diseño de la arquitectura de control, se estudiaron los principales requisitos para estos dispositivos. Entre estos, cabe destacar la adquisición, procesado e intercambio a través de internet de numerosas señales de control e instrumentación; la computación de equaciones matemáticas incluyendo la cinemática directa e inversa, jacobiana, algoritmos de detección de agarres, etc. Todos estos componentes deben calcularse en tiempo real garantizando una frecuencia mínima de 1 KHz. Además, se describen sistemas para manipulación de precisión virtual y remota; así como el diseño de un método denominado "desacoplo cinemático iterativo" para computar la cinemática inversa de robots y la comparación con otros métodos actuales. Para entender la importancia de la interacción multimodal, se ha llevado a cabo un estudio para comprobar qué estímulos sensoriales se correlacionan con tiempos de respuesta más rápidos y de mayor precisión. Estos experimentos se desarrollaron en colaboración con neurocientíficos del instituto Technion Israel Institute of Technology. Comparando los tiempos de respuesta en la interacción unimodal (auditiva, visual y háptica) con combinaciones bimodales y trimodales de los mismos, se demuestra que el movimiento sincronizado de los dedos para generar respuestas de agarre se basa principalmente en la percepción háptica. La ventaja en el tiempo de procesamiento de los estímulos hápticos, sugiere que los entornos virtuales que incluyen esta componente sensorial generan mejores contingencias motoras y mejoran la credibilidad de los eventos. Se concluye que, los sistemas que incluyen percepción háptica dotan a los usuarios de más tiempo en las etapas cognitivas para rellenar información de forma creativa y formar una experiencia más rica. Una aplicación interesante de los dispositivos hápticos es el diseño de nuevos simuladores que permitan entrenar habilidades manuales en el sector médico. En colaboración con fisioterapeutas de Griffith University en Australia, se desarrolló un simulador que permite realizar ejercicios de rehabilitación de la mano. Las propiedades de rigidez no lineales de la articulación metacarpofalange del dedo índice se estimaron mediante la utilización del efector final diseñado. Estos parámetros, se han implementado en un escenario que simula el comportamiento de la mano humana y que permite la interacción háptica a través de esta interfaz. Las aplicaciones potenciales de este simulador están relacionadas con entrenamiento y educación de estudiantes de fisioterapia. En esta tesis, se han desarrollado nuevos métodos que permiten el control simultáneo de robots y manos robóticas en la interacción con entornos reales. El espacio de trabajo alcanzable por el dispositivo háptico, se extiende mediante el cambio de modo de control automático entre posición y velocidad. Además, estos métodos permiten reconocer el gesto del usuario durante las primeras etapas de aproximación al objeto para su agarre. Mediante experimentos de manipulación avanzada de objetos con un manipulador y diferentes manos robóticas, se muestra que el tiempo en realizar una tarea se reduce y que el sistema permite la realización de la tarea con precisión. Este trabajo, es el resultado de una colaboración con investigadores de Harvard BioRobotics Laboratory. ABSTRACT When we interact with the environment in our daily life (using a toothbrush, opening doors, using cell-phones, etc.), or in professional situations (medical interventions, manufacturing processes, etc.) we typically perform dexterous manipulations that involve multiple fingers and palm for both hands. Therefore, multi-Finger haptic methods can provide a realistic and natural human-machine interface to enhance immersion when interacting with simulated or remote environments. Most commercial devices allow haptic interaction with only one contact point, which may be sufficient for some exploration or palpation tasks but are not enough to perform advanced object manipulations such as grasping. In this thesis, I investigate the mechanical design, control and applications of a modular haptic device that can provide force feedback to the index, thumb and middle fingers of the user. The designed mechanical device is optimized with a multi-objective design function to achieve a low inertia, a large workspace, manipulability, and force-feedback of up to 3 N within the workspace; the bandwidth and rigidity for the device is assessed through simulation and real experimentation. One of the most important areas when designing haptic devices is the end-effector, since it is in contact with the user. In this thesis the design and evaluation of a thimble-like, lightweight, user-adaptable, and cost-effective device that incorporates four contact force sensors is described. This design allows estimation of the forces applied by a user during manipulation of virtual and real objects. The design of a real-time, modular control architecture for multi-finger haptic interaction is described. Requirements for control of multi-finger haptic devices are explored. Moreover, a large number of signals have to be acquired, processed, sent over the network and mathematical computations such as device direct and inverse kinematics, jacobian, grasp detection algorithms, etc. have to be calculated in Real Time to assure the required high fidelity for the haptic interaction. The Hardware control architecture has different modules and consists of an FPGA for the low-level controller and a RT controller for managing all the complex calculations (jacobian, kinematics, etc.); this provides a compact and scalable solution for the required high computation capabilities assuring a correct frequency rate for the control loop of 1 kHz. A set-up for dexterous virtual and real manipulation is described. Moreover, a new algorithm named the iterative kinematic decoupling method was implemented to solve the inverse kinematics of a robotic manipulator. In order to understand the importance of multi-modal interaction including haptics, a subject study was carried out to look for sensory stimuli that correlate with fast response time and enhanced accuracy. This experiment was carried out in collaboration with neuro-scientists from Technion Israel Institute of Technology. By comparing the grasping response times in unimodal (auditory, visual, and haptic) events with the response times in events with bimodal and trimodal combinations. It is concluded that in grasping tasks the synchronized motion of the fingers to generate the grasping response relies on haptic cues. This processing-speed advantage of haptic cues suggests that multimodalhaptic virtual environments are superior in generating motor contingencies, enhancing the plausibility of events. Applications that include haptics provide users with more time at the cognitive stages to fill in missing information creatively and form a richer experience. A major application of haptic devices is the design of new simulators to train manual skills for the medical sector. In collaboration with physical therapists from Griffith University in Australia, we developed a simulator to allow hand rehabilitation manipulations. First, the non-linear stiffness properties of the metacarpophalangeal joint of the index finger were estimated by using the designed end-effector; these parameters are implemented in a scenario that simulates the behavior of the human hand and that allows haptic interaction through the designed haptic device. The potential application of this work is related to educational and medical training purposes. In this thesis, new methods to simultaneously control the position and orientation of a robotic manipulator and the grasp of a robotic hand when interacting with large real environments are studied. The reachable workspace is extended by automatically switching between rate and position control modes. Moreover, the human hand gesture is recognized by reading the relative movements of the index, thumb and middle fingers of the user during the early stages of the approximation-to-the-object phase and then mapped to the robotic hand actuators. These methods are validated to perform dexterous manipulation of objects with a robotic manipulator, and different robotic hands. This work is the result of a research collaboration with researchers from the Harvard BioRobotics Laboratory. The developed experiments show that the overall task time is reduced and that the developed methods allow for full dexterity and correct completion of dexterous manipulations.

A unified framework for linear function approximation of value functions in stochastic control

This paper contributes with a unified formulation that merges previ- ous analysis on the prediction of the performance ( value function ) of certain sequence of actions ( policy ) when an agent operates a Markov decision process with large state-space. When the states are represented by features and the value function is linearly approxi- mated, our analysis reveals a new relationship between two common cost functions used to obtain the optimal approximation. In addition, this analysis allows us to propose an efficient adaptive algorithm that provides an unbiased linear estimate. The performance of the pro- posed algorithm is illustrated by simulation, showing competitive results when compared with the state-of-the-art solutions.