CO2 capture by absorption into aqueous tertiary amine solution

The aim of this research is to obtain the absorption rate of CO2 into aqueous solution of N,N- di methyl ethanolamine and into aqueous solution of Triethylene diamine and to demonstrate the importance of absorption of CO2 in nowadays by discussing global warming and greenhouse effect. It is also discussed the current situation of China focusing in the latest steps this country has recently made. In the experimental part of this work, the two tertiary amine solutions will absorb CO2 in a Lewis type cell, measuring the pressure change during the reactions take place. The temperature will be between 35 degree and 70 degree Celsius. The results of both solutions, concentrations of 0.5 and 1.0 mol per liter, are discussed and a single value of the rate constant is given for the first time along with some others parameters.

Determination of the uptake and translocation of nitrogen applied at different growth stages of a melon crop (Cucumis melo L.) using 15N isotope.

In order to establish a rational nitrogen (N) fertilisation and reduce groundwater contamination, a clearer understanding of the N distribution through the growing season and its dynamics inside the plant is crucial. In two successive years, a melon crop (Cucumis melo L. cv. Sancho) was grown under field conditions to determine the uptake of N fertiliser, applied by means of fertigation at different stages of plant growth, and to follow the translocation of N in the plant using 15N-labelled N. In 2006, two experiments were carried out. In the first experiment, labelled 15N fertiliser was supplied at the female-bloom stage and in the second, at the end of fruit ripening. Labelled 15N fertiliser was made from 15NH415NO3 (10 at.% 15N) and 9.6 kg N ha−1 were applied in each experiment over 6 days (1.6 kg N ha−1 d−1). In 2007, the 15N treatment consisted of applying 20.4 kg N ha−1 as 15NH415NO3 (10 at.% 15N) in the middle of fruit growth, over 6 days (3.4 kg N ha−1 d−1). In addition, 93 and 95 kg N ha−1 were supplied daily by fertigation as ammonium nitrate in 2006 and 2007, respectively. The results obtained in 2006 suggest that the uptake of N derived from labelled fertiliser by the above-ground parts of the plants was not affected by the time of fertiliser application. At the female-flowering and fruit-ripening stages, the N content derived from 15N-labelled fertiliser was close to 0.435 g m−2 (about 45% of the N applied), while in the middle of fruit growth it was 1.45 g m−2 (71% of the N applied). The N application time affected the amount of N derived from labelled fertiliser that was translocated to the fruits. When the N was supplied later, the N translocation was lower, ranging between 54% at female flowering and 32% at the end of fruit ripening. Approximately 85% of the N translocated came from the leaf when the N was applied at female flowering or in the middle of fruit growth. This value decreased to 72% when the 15N application was at the end of fruit ripening. The ammonium nitrate became available to the plant between 2 and 2.5 weeks after its application. Although the leaf N uptake varied during the crop cycle, the N absorption rate in the whole plant was linear, suggesting that the melon crop could be fertilised with constant daily N amounts until 2–3 weeks before the last harvest.

Ensayos de laboratorio para la medida de la tasa de absorción específica (SAR) en dispositivos móviles

El proyecto trata del estudio de la tasa de absorción específica (SAR). En él se estudia la SAR que desprenden distintos dispositivos de comunicaciones inalámbricos. Se ha llevado a cabo en las instalaciones de la SETSI, en el laboratorio de radiofrecuencia situado en El Casar, Guadalajara, que pertenece al Ministerio de Industria Comercio y Turismo. La SAR es una relación entre la energía electromagnética acumulada en una masa de un material o tejido concreto. Por tanto, lo primero es definir la SAR, en la que se exponen sus parámetros. Además, se recogen los límites de exposición fijados por las normas internacionales IEC 62209-1 e IEC 62209-2 en relación a SAR. Posteriormente, acorde con las normas, se realiza una definición detallada de un banco de medidas de SAR, en donde se explica cada uno de los componentes del banco de manera detallada así como los sistemas que intervienen previamente a la realización de la medida, tipos de los sistemas para realizar las verificaciones pertinentes, y también las incertidumbres de ciertos parámetros. También se realiza un proceso completo de medida de SAR en el laboratorio de la SETSI, donde se realizan las comprobaciones necesarias para la realización de una serie de medidas sobre dispositivos de comunicaciones móviles. Éstas medidas se realizan primero sobre un teléfono móvil en las frecuencias de GSM, UMTS y WIFI, en las configuraciones estipuladas por la norma; “tocando” e “inclinada 15°” comparando los valores obtenidos con los límites marcados por las normas internacionales. Por último, en este apartado se realizan ciertas medidas con otras configuraciones que no están recogidas en la norma para intentar obtener los máximos valores de SAR posibles. Después se realiza una comparación entre dos dispositivos tipo “tablet”, para ello se realizan medidas en la banda de WIFI y se comentan los resultados obtenidos, relacionado con el diseño de cada uno de ellos. Posteriormente se realiza un presupuesto de un banco de SAR, donde se detallan todos los componentes que intervienen en la realización de las medidas de SAR, pero no se incluyen en él, los costes de mantenimiento o los costes relacionados con su uso. Por último se explican las conclusiones finales desprendidas de la realización de este proyecto de fin de carrera así como la bibliografía utilizada. ABTRACT This project consists on the study of the specific absorption rate (SAR).It studies the different SAR of several wireless communications devices. It has been held in SETSI’S facilities, in its radio frecuency laboratory located in El Casar, Guadalajara, which belongs to the Ministy of Industry, Trade and Tourism. The SAR is a ratio between the electromagnetic energy accumulated in a mass of concrete material or tissue. Therefore, the SAR is defined first, which sets its parameters. Also lists the exposure limits set by international standards IEC 62209-1 and IEC 62209-2 regarding SAR. Subsequently, according to the guidelines, performing a detailed definition of a SAR measures bench, which explains each of the components in detail of the bench and involved systems prior to the realization of the extent and types of systems to perform the necessary checks, and certain parameters uncertainties. Also performed a complete process for SAR in the SETSI laboratory, located in El Casar, Guadalajara, where the necessary checks are made to carry out a serie of measures on mobile communications devices. These will be carried out first on a mobile phone at frequencies of GSM, UMTS and WiFi, in the configurations set by the standard, "touch" and "tilt 15 °" comparing the values obtained with the limits set by international standards. Finally, this section will perform certain actions with other configurations that are not included in the standard to try to get the maximum possible SAR values. Then a comparison is made between two devices, such as "tablet", this will make measurements in the band WIFI and discussed the results, related to the design of each. Subsequently, a budget of a SAR bench, detailing all components involved in SAR measures, but not included in it, maintenance costs or the costs associated with its use. Finally conclusions are explained detached from the realization of this project as well as the bibliography used on it.

Comparativa de las medidas de emisiones electromagnéticas en las normativas europea y americana para teléfonos duales

El objetivo del presente Proyecto Fin de Grado es la realización de una comparativa de los resultados obtenidos en las medidas de SAR (tasa de absorción específica) y potencia utilizando la normativa europea CENELEC (basada en la del IEC) y la americana FCC (basada en la del IEEE) para distintos dispositivos móviles duales. En primer lugar se ha realizado el estudio de sus características de potencia y de SAR, viendo la variación que hay con respecto a las distintas normativas y rangos de frecuencias. En algunos casos, aunque funcionan sin problema alguno en las diferentes bandas, la diferencia de niveles de emisiones obtenidos en las diferentes bandas puede ser notable. Como se ha comentado al comienzo, se han utilizado diferentes dispositivos duales y se realizaron en ellos las medidas pertinentes utilizando las diferentes normativas y el procedimiento indicado en cada una de ellas. Para observar las diferencias concretas que pudieran existir al utilizar las diferentes normativas, las medidas se han realizado en todas las bandas de funcionamiento del dispositivo y para cada una de ellas se han aplicado las diferentes normativas. Con esto se pretende evaluar si pudiera existir alguna discrepancia en los dispositivos que tienen el certificado de conformidad para una norma concreta cuando se utiliza en otra banda que no es exactamente la banda de utilización de esa norma. En resumen, se quería comprobar que un dispositivo que está certificado con la norma de una región, por ejemplo Europa (900 y 1800 MHz), también cumple si se utiliza en otra región, por ejemplo América (850 y 1900 MHz). La realización práctica del presente PFG se ha hecho en las instalaciones del Laboratorio de Radiofrecuencia de la Secretaría de Estado de Telecomunicación y para la Sociedad de la Información ubicado en El Casar (Guadalajara). En concreto se utilizó el robot articulado movible DASY4 y el software para su control DASY 52.8, disponible en el “banco de medida de Campos Electromagnéticos (Sala de SAR)”. La duración estimada del presente PFG ha sido aproximadamente de cuatro meses. Para llevar a cabo el presente PFG, se dispuso de todo tipo de material y recursos puestos a disposición por el Ministerio de Industria, Turismo y Comercio en el propio laboratorio, así como de los distintos terminales móviles duales con los que se realizaron las medidas pertinentes. Como bibliografía básica se han utilizado las diferentes normas indicadas anteriormente, es decir la norma europea CENELEC (basada en la del IEC) y la americana FCC (basada en la del IEEE), así como manuales de los equipos implicados en el bando de medida de SAR: analizadores de redes, robot articulado y software de control, así como el resto de dispositivos utilizados en las medidas. ABSTRACT. The goal of this Final Degree Project is to perform a comparison of the results obtained in SAR measurements (specific absorption rate) and power using the European standards CENELEC (based on IEC Regulation) and the American FCC (based on IEEE Regulation) to different mobile dual devices. If first place it was made the study of its power and SAR features, seeing that there is shift with respect to the different standards and frequency ranges. In some cases, although they work without any problem in different bands, the difference in levels of emissions obtained in the different bands can be significant. As mentioned at the beginning, different dual devices were used and relevant measurements were taken from them using the different standards and the procedure in each one of them. To see the specific differences that may exist when using the different standards, the measurements were made in all bands of the device operation and to each one it has been applied in the different standards. This attempted to assess whether there could be some discrepancy in the devices that have the certificate of compliance to a specify standard when used in another band that is not exactly the used band of this standard. To sum up, it was required to verify that a device which is certified to the standard of a region, for example (900 and 1800 MHz), also verifies if it is used in another region, for example America (850 and 1900 MHz). The practical realization of this Final Degree Project was made in the facilities of the Radio Frequency Laboratory of the Ministry of State for Telecommunications and the Information Society located in El Casar (Guadalajara). Specifically, the movable articulated robot DASY4 was used and the control software DASY 52.8, available in the “Measure Electromagnetic Field testbench (SAR room)”. The duration of this Final Degree Project has benn about four months. To carry out the present project, all kinds of materials and resources were provided by the Ministry of Industry, Tourism and Trade in its own laboratory, as well as the different mobile dual terminals with which relevant measurements were made. As basic references the different standards indicated above has been used, that is to say the European standard CENELEC (based on IEC standard) and the American FCC (based on IEEE standard), as well as the equipment manuals involved in the SAR measure testbench: network analyzers, articulated robot and control software, as well as the rest of the devices used in the measurements.

Inverse bremsstrahlung absorption in spherical laser targets

Inverse bremsstrahlung has been incorporated into an analytical model of the expanding corona of a laser-irradiated spherical target. Absorption decreases slowly with increasing intensity, in agreement with some numerical simulations, and contrary to estimates from simple models in use up to now, which are optimistic at low values of intensity and very pessimistic at high values. Present results agree well with experimental data from many laboratories; substantial absorption is found up to moderate intensities,say below IOl5 W cm-2 for 1.06 pm light. Anomalous absorption, wher, included in the analysis, leaves practically unaffected the ablation pressure and mass ablation rate, for given absorbed intensity. Universal results are given in dimensionless fom.