Site-controlled Ag nanocrystals grown by molecular beam epitaxy-Towards plasmonic integration technology

We demonstrate site-controlled growth of epitaxial Ag nanocrystals on patterned GaAs substrates by molecular beam epitaxy with high degree of long-range uniformity. The alignment is based on lithographically defined holes in which position controlled InAs quantum dots are grown. The Ag nanocrystals self-align preferentially on top of the InAs quantum dots. No such ordering is observed in the absence of InAs quantum dots, proving that the ordering is strain-driven. The presented technique facilitates the placement of active plasmonic nanostructures at arbitrarily defined positions enabling their integration into complex devices and plasmonic circuits.

Mechanical Characterization of Lead-Free Sn-Ag-Cu Solder Joints by High-Temperature Nanoindentation

The reliability of Pb-free solder joints is controlled by their microstructural constituents. Therefore, knowledge of the solder microconstituents’ mechanical properties as a function of temperature is required. Sn-Ag-Cu lead-free solder alloy contains three phases: a Sn-rich phase, and the intermetallic compounds (IMCs) Cu6Sn5 and Ag3Sn. Typically, the Sn-rich phase is surrounded by a eutectic mixture of β-Sn, Cu6Sn5, and Ag3Sn. In this paper, we report on the Young’s modulus and hardness of the Cu6Sn5 and Cu3Sn IMCs, the β-Sn phase, and the eutectic compound, as measured by nanoindentation at elevated temperatures. For both the β-Sn phase and the eutectic compound, the hardness and Young’s modulus exhibited strong temperature dependence. In the case of the intermetallics, this temperature dependence is observed for Cu6Sn5, but the mechanical properties of Cu3Sn are more stable up to 200°C.

Pozzuolanic properties of the natural zeolites of some latin american deposits

This paper shows the results of the study of physical, mechanic and chemical behaviour of some natural zeolite types sampled in different outcrops of the world, mainly from Mexico, Cuba and Spain, as well as their incidence in certain practical applications, by means of the utilization of its pozzuolanic properties. Results emphasize that every natural zeolite variety gives different answers in the assays, probably influenced by the subtle variability of their chemical composition. Key words: zeolites, pozzuolanic, density, geometric, strength

Mechanical characterization of GdBCO/Ag and YBCO single grains fabricated by top-seeded melt growth at 77 and 300 K

YBaCuO and GdBaCuO + 15 wt% Ag large, single-grain, bulk superconductors have been fabricated via the top-seeded, melt-growth (TSMG) process using a generic NdBCO seed. The mechanical behavior of both materials has been investigated by means of three-point bending (TPB) and transversal tensile tests at 77 and 300 K. The strength, fracture toughness and hardness of the samples were studied for two directions of applied load to obtain comprehensive information about the effect of microstructural anisotropy on the macroscopic and microscopic mechanical properties of these technologically important materials. Splitting (Brazilian) tests were carried out on as-melt-processed cylindrical samples following a standard oxygenation process and with the load applied parallel to the growth-facet lines characteristic of the TSMG process. In addition, the elastic modulus of each material was measured by three different techniques and related to the microstructure of each sample using optical microscopy. The results show that both the mechanical properties and the elastic modulus of both YBCO and GdBCP/Ag are improved at 77 K. However, the GdBCO/Ag samples are less anisotropic and exhibit better mechanical behavior due to the presence of silver particles in the bulk, superconducting matrix. The splitting tensile strength was determined at 77 K and both materials were found to exhibit similar behavior, independently of their differences in microstructure.

Ti/Pd/Ag Contacts to n-Type GaAs for High Current Density Devices

The metallization stack Ti/Pd/Ag on n-type Si has been readily used in solar cells due to its low metal/semiconductor specific contact resistance, very high sheet conductance, bondability, long-term durability, and cost-effectiveness. In this study, the use of Ti/Pd/Ag metallization on n-type GaAs is examined, targeting electronic devices that need to handle high current densities and with grid-like contacts with limited surface coverage (i.e., solar cells, lasers, or light emitting diodes). Ti/Pd/Ag (50 nm/50 nm/1000 nm) metal layers were deposited on n-type GaAs by electron beam evaporation and the contact quality was assessed for different doping levels (from 1.3 × 1018 cm−3 to 1.6 × 1019 cm−3) and annealing temperatures (from 300°C to 750°C). The metal/semiconductor specific contact resistance, metal resistivity, and the morphology of the contacts were studied. The results show that samples doped in the range of 1018 cm−3 had Schottky-like I–V characteristics and only samples doped 1.6 × 1019 cm−3 exhibited ohmic behavior even before annealing. For the ohmic contacts, increasing annealing temperature causes a decrease in the specific contact resistance (ρ c,Ti/Pd/Ag ~ 5 × 10−4 Ω cm2). In regard to the metal resistivity, Ti/Pd/Ag metallization presents a very good metal conductivity for samples treated below 500°C (ρ M,Ti/Pd/Ag ~ 2.3 × 10−6 Ω cm); however, for samples treated at 750°C, metal resistivity is strongly degraded due to morphological degradation and contamination in the silver overlayer. As compared to the classic AuGe/Ni/Au metal system, the Ti/Pd/Ag system shows higher metal/semiconductor specific contact resistance and one order of magnitude lower metal resistivity.

Guidelines of natural zeolites characterization for acid mine drainage treatment. Case study Guayaquil, Ecuador

Zeolites constitute one of the less common groups of tectosilicates. Zeoli1es with pores between -2 to 10 A in their structures have strong sorption capacity and are widely used in industrial and municipal operations to eliminate toxic substances. One of the major environmental problems in the mining activity is the treating of acid mine drainage. In this context, it is very important to search alternatives to manage this challenge. One feasible alternative is using zeolitic tuffs. The results of the physical-chemical characterization of zeolitic tuffs are the c1ue lo continue or not with deeper analysis and tests 01 acid mine drainage treatments. The guidelines to reach this purpose are the main goal of this work. Zeolite 1uff samples (named as XB_01 and XB_02) studied in this work were laken rn the Late Cretaceous Coastal Cayo Arch Ecuador, specifically in the Guaraguao River, showing the most important characteristics of heulandite zeolitic tuffs. X-ray powder diffraction (XRD) tests were developed in order to confirm that the samples belong to the heulandite-type zeoli1ic tuffs. Additionally, Thermogravimetric analysis (TG), Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) and X-ray fluorescence (XRF) of the samples was necessary in order to define the Si/Al ratio and the main mineralogical phases. The XB_01 sample shows a higher ratio Si/Al than XB_02 sample. The cation exchange capacity est was the fundamental step to define the potentiality of the zeolite to use in acid mine drainage treatment Three methodologies were employed to determine the cation exchange capacity. The Cuban standard 626 and the ammonium exchange methodologies reflect results more consistent with each other. This is the starting point to continue with deeper studies such as breakthrough curves for heavy metal ions found in acid mine waters.