Estimating Perceived Video Quality from Objective Parameters in Video over IP Services

In Video over IP services, perceived video quality heavily depends on parameters such as video coding and network Quality of Service. This paper proposes a model for the estimation of perceived video quality in video streaming and broadcasting services that combines the aforementioned parameters with other that depend mainly on the information contents of the video sequences. These fitting parameters are derived from the Spatial and Temporal Information contents of the sequences. This model does not require reference to the original video sequence so it can be used for online, real-time monitoring of perceived video quality in Video over IP services. Furthermore, this paper proposes a measurement workbench designed to acquire both training data for model fitting and test data for model validation. Preliminary results show good correlation between measured and predicted values.

Subjective Evaluation of Transmission Errors in IPTV and 3DTV

The increase of multimedia services delivered over packet-based networks has entailed greater quality expectations of the end-users. This has led to an intensive research on techniques for evaluating the quality of experience perceived by the viewers of audiovisual content, considering the different degradations that it could suffer along the broadcasting system. In this paper, a comprehensive study of the impact of transmission errors affecting video and audio in IPTV is presented. With this aim, subjective assessment tests were carried out proposing a novel methodology trying to keep as close as possible home environment viewing conditions. Also 3DTV content in side-by-side format has been used in the experiments to compare the impact of the degradations. The results provide a better understanding of the effects of transmission errors, and show that the QoE related to the first approach of 3DTV is acceptable, but the visual discomfort that it causes should be reduced.

Making Transport Safer: V2V-Based Automated Emergency Braking System

An important goal in the field of intelligent transportation systems (ITS) is to provide driving aids aimed at preventing accidents and reducing the number of traffic victims. The commonest traffic accidents in urban areas are due to sudden braking that demands a very fast response on the part of drivers. Attempts to solve this problem have motivated many ITS advances including the detection of the intention of surrounding cars using lasers, radars or cameras. However, this might not be enough to increase safety when there is a danger of collision. Vehicle to vehicle communications are needed to ensure that the other intentions of cars are also available. The article describes the development of a controller to perform an emergency stop via an electro-hydraulic braking system employed on dry asphalt. An original V2V communication scheme based on WiFi cards has been used for broadcasting positioning information to other vehicles. The reliability of the scheme has been theoretically analyzed to estimate its performance when the number of vehicles involved is much higher. This controller has been incorporated into the AUTOPIA program control for automatic cars. The system has been implemented in Citroën C3 Pluriel, and various tests were performed to evaluate its operation.

Integración Wi-Fi en un proyecto ICT

La instalación de Infraestructuras Comunes de Telecomunicación (IICCTT) en el interior de las edificaciones para el acceso a los servicios de telecomunicación facilitó la incorporación a las viviendas de las nuevas tecnologías de forma económica y transparente para los usuarios. Actualmente, todos los edificios de nueva construcción deben presentar un proyecto ICT firmado por un Ingeniero Técnico de Telecomunicación de la especialidad correspondiente o un Ingeniero de Telecomunicación. La legislación que las regula afecta a todo tipo de viviendas con independencia del poder adquisitivo del comprador, y contribuye de manera decisiva a que disminuyan a corto y medio plazo las desigualdades sociales en lo relativo al acceso a servicios de telecomunicación tales como telefonía, Internet, telecomunicación por cable, radiodifusión sonora y televisión analógica, digital, terrenal o por satélite, etc.. Desde 1997, el Colegio Oficial de Ingenieros de Telecomunicación junto con otras organizaciones públicas y privadas ha participado en la elaboración de la normativa aplicable a las Infraestructuras Comunes de Telecomunicación, dando lugar al actual decreto, el Real Decreto 346/2011, de 11 de Marzo. El propósito general de este proyecto es diseñar una red Wi-Fi a partir de las canalizaciones e instalaciones del proyecto ICT de un conjunto de viviendas unifamiliares, para que todas ellas dispongan de conexión a internet de forma inalámbrica. Para llevar a cabo este diseño, se ha realizado un estudio de las características del estándar IEEE 802.11, conocido como Wi-Fi, analizando las posibilidades de comunicación inalámbrica que ofrece, así como las limitaciones que presenta en la actualidad. Se ha analizado el proyecto ICT del conjunto de viviendas, estudiando la viabilidad de utilizar sus instalaciones para implementar la red Wi-Fi, añadiendo tanto las canalizaciones como los dispositivos comerciales necesarios para llevar a cabo dicha implementación. Además, se ha estudiado la posibilidad de integrar la red Wi-Fi utilizando el cableado de televisión de la propia ICT. Por último, se ha estudiado la gran importancia que al Hogar Digital se da en el Real Decreto 346/2011, de 11 de marzo, por el que se aprueba el Reglamento regulador de las Infraestructuras Comunes de Telecomunicaciones para el acceso a los servicios de telecomunicación en el interior de las edificaciones, presentando los aspectos fundamentales que se persiguen con la domotización de la vivienda como mejora de vida de sus habitantes. Abstract The installation of Telecommunications Common Infrastructures (TCIs, in Spanish Infraestructuras Comunes de Telecomunicación –IICCTT-) in the buildings, in order to gain access to telecommunications services, facilitated the incorporation into the houses of new technologies in an economical and transparent way for users. Nowadays, every new construction building must have a TCI project signed by a Telecommunications Engineer or a Technical Telecommunications Engineer with the appropriate specialization. The legislation that regulates TCIs affects every kind of houses, independently of the buyer´s purchasing power, and contributes decisively to decrease in short and medium terms the social inequalities concerning the access to the telecommunication services, such as telephony, Internet, wired telecommunications, audible broadcasting and digital, analogical, land, satellite television, etc.. Since 1997, the Telecommunications Engineer Official College, together with other public and private organizations, has been elaborating the regulations for the TCIs, giving rise to the current decree, the Royal Decree 346/2011, of 11th of March. The general purpose of this project is to design a Wi-Fi network based on the canalizations and installations of the TCI project of a housing development, in such a way that every house is provided with a wireless connection to the Internet. In order to carry out this design, the characteristics of the standard IEEE 802.11, known as Wi-Fi, have been studied, analyzing the wireless-communication possibilities that it offers, as well as the constraints that it presents currently. The TCI project has been analyzed, studying the feasibility of using its installations to implement the Wi-Fi network, adding the canalizations and commercial devices required to execute the aforementioned implementation. Besides, the possibility of integrating the Wi-Fi network using the television wires of the TCI project has been investigated. Finally, it has been studied the great importance that has been given to Digital Home in the Royal Decree 346/2011, of 11th of March, that approves the regulatory Regulations of Telecommunications Common Infrastructures for the access to telecommunications services inside the buildings, presenting the essential aspects that are pursued with the house domotization as a way to improve the quality of life of its inhabitants.

Educational innovation applied in the UNESCO chair of mining and industrial heritage

The “Innovatio Educativa Tertio Millennio” group has been 10 years developing educational innovation techniques, actually has reached the level of teaching on the technical teachers has developed, and share them with other groups, that can implement them in their teaching activities. UNESCO Chair of Mining and Industrial Heritage has been years working on heritage, and on the one hand teaching in conservation and maintenance of heritage, and on the other doing raise awareness of the meaning of heritage, the social value and as must be managed effectively. Recently these two groups work together, thus is spreading in a much more effective manner the concepts of heritage, its meaning, its value, and how to manage it and provide effective protection. On one hand being a work of dissemination based on internet and on radio broadcasting, and on the other one of teaching based on educational innovation, and courses, conferences, and face-to-face seminars or distance platforms.

Remote Delivery of Video Services over video links

The spreading of new systems of broadcasting and distribution of multimedia content has had as a consequence a larger need for aggregation of data and metadata to traditionally based contents of video and audio supply. Broadcasting chains of this type of channels have become overwhelmed by the quantity of resources, infrastructures and development needed for these channels to provide information. In order to avoid this kind of shortcomings, several recommendations and standards have been created to exchange metadata between production and distribution of taped programs. The problem lies in live programs, producers sometimes offer data to channels but most often, channels are not able to face required developments. The key to this problem is cost reduction. In this work, a study is conducted on added services which producers may provide to the media about content; a system is found by which additional communication expenses are not made and a model of information transfer is offered which allows low cost developments to supply new media platforms.

Gestión de pruebas para equipos de vídeo

Desde hace ya muchos años, uno de los servicios de telecomunicaciones más demandado por los españoles ha sido la televisión de pago, complementando y ampliando la oferta de contenidos audiovisuales que habitualmente son ofrecidos de manera gratuita por la televisión analógica y recientemente por la televisión digital terrestre o TDT. Estos servicios de video, han sido tradicionalmente ofrecidos por operadores satélites, operadores de cable u otros operadores de telecomunicaciones con los que a través de una conexión de datos (ADSL, VDSL o fibra óptica), ofrecían sus contenidos a través de IP. La propia evolución y mejora de la tecnología utilizada para la emisión de contenidos sobre IP, ha permitido que a día de hoy, la televisión se conciba como un servicio Over The Top (OTT) ajeno al medio de transmisión, permitiendo a cualquier agente, distribuir sus contenidos audiovisuales de manera sencilla y a todos sus clientes en todas las partes del mundo; siendo solamente necesario disponer de una conexión a internet. De esta manera, el proyecto desarrollado va a girar en torno a la herramienta StormTest de la empresa S3Group, comprada por CENTUM Solutions (empresa especializada en ofrecer servicio de ingeniería para sistema de comunicaciones, control e inteligencia de señal) con el objetivo de satisfacer las necesidades de sus clientes y con la que en definitiva se ha contado para la realización de este proyecto. El principal objetivo de este proyecto es la definición e implementación de un banco de pruebas que permita optimizar los procesos de validación técnica, mejorando los tiempos de ejecución y concentrando la actividad de los ingenieros en tareas de mayor valor. Para la realización de este proyecto, se han fijado diversos objetivos necesarios para el desarrollo de este tipo de actividades. Los principales son los siguientes:  Análisis de la problemática actual: donde en los procesos de aceptación técnica se dedica muchas horas de trabajo para la realización de pruebas repetitivas y de poco valor las cuales se pueden automatizar por herramientas existentes en el mercado.  Búsqueda y selección de una herramienta que satisfaga las necesidades de pruebas.  Instalación en los laboratorios.  Configuración y adaptación de la herramienta a las necesidades y proyectos específicos. Con todo ello, este proyecto cubrirá los siguientes logros:  Reducir los tiempos de ejecución de las campañas de pruebas, gracias a la automatización de gran parte ellas.  Realizar medidas de calidad subjetiva y objetiva complejas, imposibles de ejecutar a través de las personas. Mejorar y automatizar los sistemas de reporte de resultados. Abstract: Many years ago, one of the telecommunications services most demanded in Spain has been pay television, complementing and extending the offer of audiovisual content which are usually offered for free by analog tv and recently by digital terrestrial televisión or TDT. These video services, have been traditionally offered by satellite operators, cable operators or other telecommunications operators that through a data connection (ADSL,VDSL or fiber optic), offered its content over IP. The evolution and improvement of the technology used for broadcasting over IP, has allowed that to date, television is conceived as a service Over The Top (OTT), not dependent on the transmission medium, allowing any agent to distribute audiovisual content in a very simple way and to all its customers in all parts of the world; being only necessary to have an decent internet connection. In this way, the project will have relation with S3Group’s StormTest tool, bought by CENTUM Solutions (company specialized in engineering services for communications, control and signal intelligence system) with the aim of satisfying the needs of its customers and which ultimately has counted for the realization of this project. The main objective of this project is the definition and implementation of a test bench that allows to optimize the processes of technical validation, improving execution times and concentrating the activities of engineers on higher value tasks. For the realization of this project, it has been defined several objectives necessary for the development of this type of activity. The most important tones are listed below:  Analysis of the current situation: where in technical acceptance processes it is dedicated many hours of work for the completion of repetitive testing and without value which can be automated by tools available on the market  Search and selection of a tool that meets the needs of testing.  Installation on the laboratories.  Configuration and customization of the tool to specific projects. With all this, this project will cover the following achievements: Reduce the execution time of the testing campaigns, thanks to the automation of many of them.  Measurements of subjective and objective quality tests, impossible to run with engineers (due to subjective perception). Improve and automate reporting of results systems

Desarrollo de la radio en el marco de las rivalidades político-militares de principios del siglo XX

A lo largo de este proyecto, se analizarán los comienzos de la radio en las primeras décadas del siglo XX, teniendo como objetivo describir el desarrollo científico-tecnológico y las rivalidades político-militares de las potencias europeas de Reino Unido y Alemania. En primer lugar se verán los precursores de la radio que existían anteriormente al surgimiento de la radiotelegrafía como la telegrafía óptica, la telegrafía eléctrica o el teléfono. Al igual que los primeros investigadores, como James Clerk Maxwell o Heinrich Rudolf Hertz, gracias a los cuales el origen de la radio fue posible. También se analizará el contexto histórico-político de Reino Unido y Alemania donde se muestran las características de las dos grandes potencias del momento, el Imperio Británico y el Imperio Alemán. Además, la cada vez mayor importancia de la telegrafía sin hilos, hará necesaria una organización internacional, dando lugar a las Conferencias Internacionales de Radiotelegrafía y que enfrentarán a estas dos potencias por defender sus intereses. Guillermo Marconi, por parte de Reino Unido, y Telefunken, por parte de Alemania, serán las principales marcas comerciales de radiotelegrafía, no solo en sus respectivos países, sino también en el resto del mundo. Entre ambas compañías se verán las rivalidades por la incesante lucha de patentes, el desarrollo tecnológico y el control de los mercados. También se tratará el enfrentamiento directo que se produjo en la Primera Guerra Mundial, donde la radio jugaría un papel fundamental. Por último, se analizarán los comienzos de la radiodifusión en la segunda década del siglo XX, donde la radio ya estaba consolidada como uno de los medios de comunicación más importante de la época, capaz de llegar a todos los rincones del planeta y perfectamente integrada en la sociedad del momento. ABSTRACT. Throughout this project, it will be analyzed the beginning of the radio in the first decades of the XX century, having as goal to describe the scientific-technological development and the political-militaries opponents of the European’s countries, United kingdom and Germany. Firstly, it will be shown the radio’s precursors before the origin of the wireless telegraphy, like: optical telegraphy, electric telegraphy or telephone. Moreover, it will show the first researchers like: Clerk Maxwell or Heinrich Hertz, thanks to them, the origin of the radio was possible. In addition, it will analyze the historical-political context of United Kingdom and Germany, where it is shown the main features of the Britain Empire and the German Empire. Moreover, the importance of the telegraphy without wire will make necessary and international organization, resulting the International Conferences of Wireless Telegraphy and it will put together these main countries in order to protect their interests. Guglielmo Marconi, by United Kingdom, and Telefunken, by Germany, they will be the main commercials brand of the wireless telegraphy, not only in their countries, but also in all over the world. Between both companies will be seen the main competitions for their patens, the technology development and the market’s control. Moreover, it will be dealt the direct conflict in the First World of War, where the radio has a fundamental role. Finally, it will be analyze the beginning of the wireless broadcasting in the second decade of the XX century, where the radio was established as one of the most important media of the age, able to arrive at every places of the world and it was perfectly integrated in the society of that moment.

Diseño y test VHDL de un cambiador de formato para ver TV3D en un televisor convencional

La difusión de TV3D actual utiliza formatos como el Side-by-Side o Top-and-Bottom, en los que cada par de imágenes, correspondiente a las vistas de los ojos derecho e izquierdo, se encapsula con la mitad de la resolución espacial en una sola imagen. Estas imágenes se muestran de manera casi simultánea de forma que el ojo humano compone una imagen con profundidad que se asemeja a la visión binocular natural. Desde hace un par de años las principales plataformas de televisión han empezado a crear canales con contenido 3D. La televisión 3D (TV3D) se ha introducido en los hogares gracias a los televisores estereoscópicos. Estos televisores, que son compatibles con los formatos antes mencionados, extraen de cada imagen sus dos vistas, recuperan la resolución original y presentan cada vista alternativamente en la pantalla, generando al mismo tiempo una señal de sincronismo para las gafas activas, creando de esta forma la sensación tridimensional de las imágenes. En este PFC se pretende realizar el diseño VHDL de un cambiador de formato que genere en tiempo real la secuencia de imágenes correspondiente a los ojos derecho e izquierdo, con resolución completa, a partir de una secuencia codificada en formato tipo Top-and-Bottom y el banco de test para su prueba. Este circuito se implementará como un periférico del procesador NIOS II de Altera. El diseño podría utilizarse como parte de un sistema que permita la visualización de las actuales emisiones de televisión 3D en un televisor convencional. La tecnología de referencia que se utilizará serán las FPGAs, más concretamente la tarjeta Cyclone III FPGA Starter Kit (EP3C25 FPGA) de Altera, junto a una tarjeta de ampliación de Microtronix con entrada y salida HDMI para video y audio. Además se pretende crear la documentación necesaria para el desarrollo de futuros trabajos relacionados con la televisión 3D. ABSTRACT Current TV3D broadcasting uses formats as Side-by-Side or Top-and-Bottom, where every single pair of images, corresponding to left and right eyes views, are encapsulated with half spatial resolution in one single image. These images are almost simultaneously displayed so that the human eye forms an image with depth resembling naturally binocular vision. From a couple of years the major TV platforms have begun to create 3D content channels. 3D Television (3DTV) has been introduced in homes through stereoscopic televisions. These televisions, which are compatible with the above formats, each image is extracted from the two views, and recover the original resolution and displays alternately each view in screen, while generating a synchronization signal for active glasses, thereby creating the three-dimensional sensation of the images. The main objective in this PFC is to make the design of an exchanger VHDL format in real time to generate the image sequence corresponding to the right and left eyes, with full resolution from an encoded sequence type format Top-and-Bottom and test bench for testing. This circuit is implemented as a Altera NIOS II processor peripheral.The design could be used as part of a system enabling the display of current television broadcasts 3D on a conventional television. The reference technology that will be use are FPGAs, more specifically Cyclone III FPGA Starter Card Kit (EP3C25 FPGA) Altera, along with an expansion card Microtronix with HDMI input and output video and audio. It also aims to create documentation for the development of future works related to 3D TV.

Localization and Tracking in Energy-Constrained Networks with Dynamic Connectivity

Systems used for target localization, such as goods, individuals, or animals, commonly rely on operational means to meet the final application demands. However, what would happen if some means were powered up randomly by harvesting systems? And what if those devices not randomly powered had their duty cycles restricted? Under what conditions would such an operation be tolerable in localization services? What if the references provided by nodes in a tracking problem were distorted? Moreover, there is an underlying topic common to the previous questions regarding the transfer of conceptual models to reality in field tests: what challenges are faced upon deploying a localization network that integrates energy harvesting modules? The application scenario of the system studied is a traditional herding environment of semi domesticated reindeer (Rangifer tarandus tarandus) in northern Scandinavia. In these conditions, information on approximate locations of reindeer is as important as environmental preservation. Herders also need cost-effective devices capable of operating unattended in, sometimes, extreme weather conditions. The analyses developed are worthy not only for the specific application environment presented, but also because they may serve as an approach to performance of navigation systems in absence of reasonably accurate references like the ones of the Global Positioning System (GPS). A number of energy-harvesting solutions, like thermal and radio-frequency harvesting, do not commonly provide power beyond one milliwatt. When they do, battery buffers may be needed (as it happens with solar energy) which may raise costs and make systems more dependent on environmental temperatures. In general, given our problem, a harvesting system is needed that be capable of providing energy bursts of, at least, some milliwatts. Many works on localization problems assume that devices have certain capabilities to determine unknown locations based on range-based techniques or fingerprinting which cannot be assumed in the approach considered herein. The system presented is akin to range-free techniques, but goes to the extent of considering very low node densities: most range-free techniques are, therefore, not applicable. Animal localization, in particular, uses to be supported by accurate devices such as GPS collars which deplete batteries in, maximum, a few days. Such short-life solutions are not particularly desirable in the framework considered. In tracking, the challenge may times addressed aims at attaining high precision levels from complex reliable hardware and thorough processing techniques. One of the challenges in this Thesis is the use of equipment with just part of its facilities in permanent operation, which may yield high input noise levels in the form of distorted reference points. The solution presented integrates a kinetic harvesting module in some nodes which are expected to be a majority in the network. These modules are capable of providing power bursts of some milliwatts which suffice to meet node energy demands. The usage of harvesting modules in the aforementioned conditions makes the system less dependent on environmental temperatures as no batteries are used in nodes with harvesters--it may be also an advantage in economic terms. There is a second kind of nodes. They are battery powered (without kinetic energy harvesters), and are, therefore, dependent on temperature and battery replacements. In addition, their operation is constrained by duty cycles in order to extend node lifetime and, consequently, their autonomy. There is, in turn, a third type of nodes (hotspots) which can be static or mobile. They are also battery-powered, and are used to retrieve information from the network so that it is presented to users. The system operational chain starts at the kinetic-powered nodes broadcasting their own identifier. If an identifier is received at a battery-powered node, the latter stores it for its records. Later, as the recording node meets a hotspot, its full record of detections is transferred to the hotspot. Every detection registry comprises, at least, a node identifier and the position read from its GPS module by the battery-operated node previously to detection. The characteristics of the system presented make the aforementioned operation own certain particularities which are also studied. First, identifier transmissions are random as they depend on movements at kinetic modules--reindeer movements in our application. Not every movement suffices since it must overcome a certain energy threshold. Second, identifier transmissions may not be heard unless there is a battery-powered node in the surroundings. Third, battery-powered nodes do not poll continuously their GPS module, hence localization errors rise even more. Let's recall at this point that such behavior is tight to the aforementioned power saving policies to extend node lifetime. Last, some time is elapsed between the instant an identifier random transmission is detected and the moment the user is aware of such a detection: it takes some time to find a hotspot. Tracking is posed as a problem of a single kinetically-powered target and a population of battery-operated nodes with higher densities than before in localization. Since the latter provide their approximate positions as reference locations, the study is again focused on assessing the impact of such distorted references on performance. Unlike in localization, distance-estimation capabilities based on signal parameters are assumed in this problem. Three variants of the Kalman filter family are applied in this context: the regular Kalman filter, the alpha-beta filter, and the unscented Kalman filter. The study enclosed hereafter comprises both field tests and simulations. Field tests were used mainly to assess the challenges related to power supply and operation in extreme conditions as well as to model nodes and some aspects of their operation in the application scenario. These models are the basics of the simulations developed later. The overall system performance is analyzed according to three metrics: number of detections per kinetic node, accuracy, and latency. The links between these metrics and the operational conditions are also discussed and characterized statistically. Subsequently, such statistical characterization is used to forecast performance figures given specific operational parameters. In tracking, also studied via simulations, nonlinear relationships are found between accuracy and duty cycles and cluster sizes of battery-operated nodes. The solution presented may be more complex in terms of network structure than existing solutions based on GPS collars. However, its main gain lies on taking advantage of users' error tolerance to reduce costs and become more environmentally friendly by diminishing the potential amount of batteries that can be lost. Whether it is applicable or not depends ultimately on the conditions and requirements imposed by users' needs and operational environments, which is, as it has been explained, one of the topics of this Thesis.

Five-year results of a slant-path propagation experiment at 20 GHz in Madrid

Satellite operators are starting to use the Ka-band (30/20 GHz) for communications systems requiring higher traffic capacity. The use of this band is expected to experience a significant growth in the next few years, as several operators have reported plans to launch new satellites with Ka-band capacity. It is worth mentioning the Ka-Sat satellite in Europe, launched in 2010, and ViaSat-1, of 2011, with coverage of USA1. Some other examples can be found in other parts of the World. Recent satellite communications standards, such as DVB-S22 or DVB-RCS3, which provide means to mitigate propagation impairments, have been developed with the objective of improving the use of the Ka-band, in comparison with previous technical standards. In the next years, the ALPHASAT satellite will bring about new opportunities4 for carrying out propagation and telecommunication experiments in the Ka- and Q/V-bands. Commercial uses are focused on the provision of high speed data communications, for Internet access and other applications. In the near future, it is expected that higher and higher data rates will also be needed to broadcast richer multimedia contents, including HD-TV, interactive content or 3D-TV. All of these services may be provided in the future by satellites of the current generation, whose life span can extend up to 2025 in some cases. Depending on local regulations, the available bandwidth for the satellite fixed and broadcasting services in the Ka-band is in excess of several hundred MHz, bidirectional, comprising more than 1 GHz for each sub-band in some cases. In this paper, the results of a propagation experiment that is being carried out at Universidad Politécnica de Madrid (UPM), Spain, are presented5. The objective of the experiment is twofold: gathering experimental time series of attenuation and analyzing them in order to characterize the propagation channel at these frequencies6. The experiment and statistical results correspond to five complete years of measurements. The experiment is described in more detail in Section II. Yearly characteristics of rain attenuation are presented in Section III, whereas Section IV is dedicated to the monthly, seasonal, and hourly characteristics. Section V covers the dynamic characteristics of this propagation effect, just before the conclusions are described in Section VI.

Diseño de una red de acceso mediante fibra óptica

Con el objetivo de consolidar los conocimientos en Sistemas de Telecomunicación, se pretende diseñar una red para la distribución de servicios avanzados, como televisión, internet de banda ancha y telefonía, mediante el uso de la tecnología FTTH. La red será totalmente pasiva, óptica, y de gran ancho de banda, Tipo PON (Passive Optical Network), de manera que el haz de luz del emisor se distribuye hacia múltiples fibras siguiendo diferentes direcciones, o las confina en el sentido opuesto usando técnicas WDM y TDMA. En primer lugar, es preciso realizar un estudio teórico sobre las características de la fibra óptica, junto con las propiedades de los elementos activos y pasivos que interactúan con ella, para poder comprender la tecnología en la que se basa y así ofrecer una solución final acorde a las necesidades que se presenten. Tras un vistazo general a la tecnología de fibra óptica, se procede a estudiar las características y topologías de las redes de acceso basadas en la misma, junto con los requisitos de cara al diseño de la redes y a la gestión de proyectos. Se definirán los objetivos de la red, ya que la complejidad de la red depende de factores como la extensión y cobertura de la misma, o el ancho de banda. Posteriormente se irá diseñando la red en una arquitectura descendente hasta destinar una única fibra óptica para cada hogar dentro de la cobertura de la red. Se detallarán todas las especificaciones necesarias para definir la red, (potencias, modulaciones y tipos de fibra) así como el instrumental y demás medios necesarios para operar con la misma. Aunque el diseño de una red FTTH contempla muchos más aspectos de los estudiados en el presente proyecto, se tomó como objetivo el diseño y planificación correspondientes a una sección de un área de escasa población donde la instalación se tomó como viable, obviando así pequeños detalles y centrándose en el despliegue de fibra óptica. Se pretende así ofrecer una solución de infraestructura doméstica de telecomunicaciones, apta para las futuras necesidades que implican la creciente demanda de servicios como internet de banda ancha o almacenamiento y procesado de aplicaciones en nube. La fibra óptica tiene mucho que ofrecer a las telecomunicaciones, y cada vez es más frecuente encontrar redes de fibra óptica como parte de un servicio de telecomunicaciones, tanto como para particulares como empresas. ABSTRACT. Aiming to strengthen knowledge in Telecommunications Systems, is intended to design a network for advanced services broadcasting, including digital TV, broadband internet and telephony, by using FTTH technology. This network will be entirely passive optic, and high bandwidth, PON type (Passive Optical Network) so that the transmitter beam is broadcasting to multiple optical fibers, branching out in different ways or joining them in the opposite. First, it is necessary to perform a theoretical study on the characteristics of the optical fiber, along with the properties of the active and passive elements that interact with it, to understand the technology that is based and offer a final solution according needs that arise. After an overview of the optical fiber technology, we proceed to study the characteristics and topologies access networks based on that, together with the requirements to face the network design and project management. System objectives will be determined, since the complexity of the network depends on factors such as the size and scope of it, or bandwidth. Later, the network will be designing in downstream architecture to deliver a single optical fiber to each household within the network area. All necessary specifications to define the network (power, modulation and fiber types) will be determined, as instruments and other means to operate it. Although FTTH network design includes many more aspects of those studied in this project, it was taken as objective the network design and planning corresponding to a section of a sparsely populated area where the facility was taken as feasible thus obviating small details and focus on the deployment of optical fiber. This is intended to provide a solution of household telecommunications infrastructure suitable for future needs involving the growing demand for services such as broadband internet or processing storage and cloud applications. The optical fiber has much to offer to telecommunications, and it is increasingly common to find fiber optic networks as part of a telecommunications service, both to individuals and businesses.

Evaluación experimental del dispositivo LRF HOKUYO URG-04LX-UG01

En robótica móvil existen diferentes dispositivos que permiten percibir la configuración del entorno. Pueden utilizarse alternativas de gran alcance como por ejemplo los ultrasonidos, pero que tienen la desventaja de consumir un tiempo elevado en la realización de las medidas. En corta distancia destacan los sensores basados en la emisión de luz infrarroja, que responden a muy alta velocidad pero tienen muy poco alcance. La obtención de fotografia, en incluso video, por medio de camaras, permite obtener mucha información del entorno, pero exige un procesado normalmente muy elaborado. Los “Laser Range Finder” son dispositivos basados en la emisión de un haz laser que responden a muy alta velocidad en el entorno de unos cuantos metros alrededor del robot móvil, lo que los hacen especialmente adecuados para un uso continuo que permita obtener de forma rapida un mapa de los obstaculos mas próximos. En el presente proyecto se va a realizar un ejercicio de medida con el laser range finder URG-04LX-UG01 para confirmar su utilidad en el ambito de la robótica móvil. ABSTRACT In mobile robotics there are different devices that allow sense the environment configuration. Powerful alternatives may be used as e.g. ultrasounds, but they have the disadvantage of consuming a large time to perform measurements. In short range highlights the infrared light based sensors, that responds at very high speed but have very low range. The photography obtaining, even video, by cameras, allow acquire many environmental information but normally require a very elaborate processing. The Laser Range Finder are devices based on laser beam broadcasting that respond a very high speed in the vicinity of a few meters around the mobile robot, which make them especially suitable for the continuous use, that allows fast obtain of the nearests obstacles map. In this project we are going to do an measurement exercise with laser range finder URG-04LX-UG01 to confirm its utility in mobile robotics scope.

Fomento del interés por la ciencia y la tecnología para estudiantes de enseñanza secundaria

Las distintas encuestas realizadas sobre la percepción social de la ciencia indican que un alto porcentaje de jóvenes no tienen interés por estas materias. Es muy importante la alfabetización científica de la población ya que ello permite tomar decisiones tanto para la vida cotidiana como sobre distintos problemas que afectan al conjunto de la sociedad. Una sociedad con más conocimiento científico--‐tecnológico lleva asociado un mayor crecimiento económico, pero desafortunadamente nos encontramos con una disminución del número de alumnos que elige estudios de Ciencia y Tecnología. Este desinterés viene influenciado tanto por factores internos al estudiante como por externos. Desde la posición docente podemos actuar sobre ellos promoviendo actividades relacionadas con la divulgación científico--‐tecnológica en clase haciendo uso de medios de comunicación que ofrezcan información procedente de fuentes fiables (prensa escrita, radio, televisión y cibermedios/web 2.0). La propuesta metodológica planteada aquí ayudará a ampliar la alfabetización científico--‐tecnológica a través de la exploración del trabajo de los investigadores actuales y de las biografías de los científicos de otras épocas. Además los alumnos crearán de forma colaborativa material propio para divulgar la Ciencia y la Tecnología en el aula. La propuesta se sitúa en el curso 1º de ESO, pero con perspectivas de extenderla en cursos sucesivos al resto de secundaria y bachillerato adaptando los contenidos . Con este trabajo pretendemos contribuir a incrementar el interés por la Ciencia y la Tecnología en el alumnado de secundaria y bachillerato. ABSTRACT The different surveys conducted in order to analyse the social perception of science show that a high percentage of young people is not interested in these subjects. The level of scientific literacy in the population is very important because it allows people to make their own decisions not only for life management skills but also for coping with the diverse problems that may affect the whole society. A society with more scientific and technological knowledge has attached a higher economic growth, but unfortunately there is a reduction in the number of students that choose Science and Tech studies. This lack of interest is influenced by the student’s internal factors as well as by the external ones. From the teacher’s point of view, it is possible to act on them, promoting activities related to scientific and technological broadcasting in the class, using mass media which can provide information from reliable sources (press, radio, television and media on the Internet/web 2.0) The methodological proposal that is made here will help to broaden scientific literacy through exploring the current researcher’s studies and the former scientifics’ biographies. Students will also create their own material in a collaborative way in order to divulgate science and technology in the classroom. The proposal is set for the first grade of secondary education, but we have in prospect to spread it during the following school years to the rest of secondary education grades and A levels only adapting its content. With this essay we want to contribute to the increasing of the interest in science and technology in high school and A levels students.

Entorno sin cinta para producción de televisión en alta definición

En este proyecto se propone un entorno de producción para televisión en alta definición donde las cintas magnéticas para la captura, modificación, gestión y transferencia de los contenidos audiovisuales, quedan sustituidas por servidores informáticos y sistemas de almacenamiento basados en las tecnologías de la información. Dicho entorno sin cintas tiene como misión la realización de la fase de la producción de los contenidos televisivos. Se trata de un centra independiente, en una ubicación remota respecto a las instalaciones centrales de la empresa emisora de televisión. La conexión del entorno sin cinta con los servicios centrales de la cadena se realiza por medio de redes de datos de alta velocidad y por enlace de radiofrecuencia. Por estos medios los sistemas de redacción comunican datos y escaletas, se reciben las señales de contribución que intervienen en los programas, se envía la serial realizada para emisión y se transfieren los materiales grabados al área de Postproducción para su elaboración final. Se plantean dos estudios de televisión dotados de servidores de video y de un almacenamiento compartido para una gestión ágil, unificada y flexible de las demandas de los programas. Además de la eliminación del lento y pesado trabajo de manipulación de las cintas, la producción resulta mucho mas ágil porque se eliminan tiempos de espera por la posibilidad de acceso simultaneo de varios usuarios a un mismo contenido. También se suprimen los tiempos de digitalización y descarga del material grabado, porque los sistemas implementados permiten la ingesta directa de las señales recibidas. Los contenidos de varias jornadas de grabación, en calidad HD, se conservan en el sistema de almacenamiento para la elaboración de materiales en el propio centra y para su transferencia al departamento central correspondiente. Mediante aplicaciones software se busca la integración del trabajo de la redacción de los programas con los procesos de producción de los estudios. El diseño que se propone para los diferentes subsistemas técnicos de los estudios esta orientado a lograr una alta fiabilidad, operatividad y adaptabilidad a las demandas técnicas de la producción audiovisual de los diferentes tipos de programas. Al tratarse de una propuesta conceptual, de manera general no se basa en equipos de marcas o fabricantes concretos sino mas bien en las metodologías concretas de trabajo. Cuando se ejemplifica algún dispositivo en particular es debido a que el concepto tecnológico del mismo es novedoso destaca de manera especial sobre la generalidad de los equipos existentes para esa funcionalidad. ABSTRACT. This project hopes to propose a television production platform that uses computers, servers and storage systems based on information technologies, rather than video tape recorders for ingesting, editing and making TV programs. This tapeless system has as its mission the production of all kind of television contents, employing IT systems, without the use of magnetic tapes. We envision an independent TV production center located in a remote location, in relation to the main broadcaster facilities, where all communications between this broadcasting center and the remote independent tapeless center would occur via high speed internet and a radiofrequency link as a back up. In this way, the Newsroom systems communicate data and rundowns; contribution feeds are received; PGM signal are codified and transmitted; and stored media are transferred to the post production area for final editing, playout and archive. Two TV studios are proposed, equipped with video servers and sharing media storage for agile, unified and flexible management of the production requirements. Apart from completely eliminating the slow and hard work resulting from handling a lot of traditional magnetic tapes, the production ends up being much quicker due to the fact that there is no waiting time between recording and viewing. This also enables several users to access and view the same material at the same time. The digitalization and downloading time is also greatly reduced due to the direct ingestion of contribution feeds to the system. The HD content of various days of recording, are stored for future use for whichever department needs the footage in the future. Through software applications, there will be complete integration between the Newsroom work and the production process of the studios. The proposed design for the various technical subsystems in the recording studio is directed towards achieving optimum reliability and operational capability: they are easily adaptable to the technical demands of the audiovisual production of the different programs. Because we are dealing with a conceptual proposal, in general terms, we are not defining the brands or manufacturers of the technical equipment, but rather we are specifying the methods which we plan to implement. When some equipment is highlighted, it's only because that specific brand exemplifies a higher performance than any other equipment in the range.