Minimum time control for multiphase buck converter: analysis and application

The combination of minimum time control and multiphase converter is a favorable option for dc-dc converters in applications where output voltage variation is required, such as RF amplifiers and dynamic voltage scaling in microprocessors, due to their advantage of fast dynamic response. In this paper, an improved minimum time control approach for multiphase buck converter that is based on charge balance technique, aiming at fast output voltage transition is presented. Compared with the traditional method, the proposed control takes into account the phase delay and current ripple in each phase. Therefore, by investigating the behavior of multiphase converter during voltage transition, it resolves the problem of current unbalance after the transient, which can lead to long settling time of the output voltage. The restriction of this control is that the output voltage that the converter can provide is related to the number of the phases, because only the duty cycles at which the multiphase converter has total ripple cancellation are used in this approach. The model of the proposed control is introduced, and the design constraints of the buck converters filter for this control are discussed. In order to prove the concept, a four-phase buck converter is implemented and the experimental results that validate the proposed control method are presented. The application of this control to RF envelope tracking is also presented in this paper.

Design of a twin capacitive load and its application to the outdoor rating of photovoltaic modules

This paper describes the design of an original twin capacitive load that is able of tracing simultaneously the I?V characteristics of two photovoltaic modules. Besides, an example of the application of this dual system to the outdoor rating of photovoltaic modules is presented, whose results have shown a good degree of repeatability.

A knowledge based application for industrialization design

After being designed, a product has to be manufactured, which means converting concepts and information into a real, physical object. This requires a big amount of resources and a careful planning. The product manufacturing must be designed too, and that is called Industrialization Design. An accepted methodology for this activity is starting defining simple structures and then progressively increasing the detail degree of the manufacturing solution. The impact of decisions taken at first stages of Industrialization Design is remarkable, and software tools to assist designers are required. In this paper a Knowledge Based Application prototype for the Industrialization Design is presented. The application is implemented within the environment CATIA V5/DELMIA. A case study with a simple Product from aerospace sector illustrates the prototype development.

Evaluating alternative industrial network organizations and information systems

Purpose – The purpose of this paper is to present a simulation‐based evaluation method for the comparison of different organizational forms and software support levels in the field of supply chain management (SCM). Design/methodology/approach – Apart from widely known logistic performance indicators, the discrete event simulation model considers explicitly coordination cost as stemming from iterative administration procedures. Findings - The method is applied to an exemplary supply chain configuration considering various parameter settings. Curiously, additional coordination cost does not always result in improved logistic performance. Influence factor variations lead to different organizational recommendations. The results confirm the high importance of (up to now) disregarded dimensions when evaluating SCM concepts and IT tools. Research limitations/implications – The model is based on simplified product and network structures. Future research shall include more complex, real world configurations. Practical implications – The developed method is designed for the identification of improvement potential when SCM software is employed. Coordination schemes based only on ERP systems are valid alternatives in industrial practice because significant investment IT can be avoided. Therefore, the evaluation of these coordination procedures, in particular the cost due to iterations, is of high managerial interest and the method provides a comprehensive tool for strategic IT decision making. Originality/value – Reviewed literature is mostly focused on the benefits of SCM software implementations. However, ERP system based supply chain coordination is still widespread industrial practice but associated coordination cost has not been addressed by researchers.

Application and modeling of GaN FET in 1MHz large signal bandwidth power supply for radio frequency power amplifier

In this paper, implementation and testing of non- commercial GaN HEMT in a simple buck converter for envelope amplifier in ET and EER transmission techn iques has been done. Comparing to the prototypes with commercially available EPC1014 and 1015 GaN HEMTs, experimentally demonstrated power supply provided better thermal management and increased the switching frequency up to 25MHz. 64QAM signal with 1MHz of large signal bandw idth and 10.5dB of Peak to Average Power Ratio was gener ated, using the switching frequency of 20MHz. The obtaine defficiency was 38% including the driving circuit an d the total losses breakdown showed that switching power losses in the HEMT are the dominant ones. In addition to this, some basic physical modeling has been done, in order to provide an insight on the correlation between the electrical characteristics of the GaN HEMT and physical design parameters. This is the first step in the optimization of the HEMT design for this particular application.

Review and Comparison of Step-Up Transformerless Topologies for Photovoltaic AC-Module Application

This paper presents a comprehensive review of stepup single-phase non-isolated inverters suitable for ac-module applications. In order to compare the most feasible solutions of the reviewed topologies, a benchmark is set. This benchmark is based on a typical ac-module application considering the requirements for the solar panels and the grid. The selected solutions are designed and simulated complying with the benchmark obtaining passive and semiconductor components ratings in order to perform a comparison in terms of size and cost. A discussion of the analyzed topologies regarding the obtained ratings as well as ground currents is presented. Recommendations for topological solutions complying with the application benchmark are provided.

Application of Public Private Partnerships to the Spanish Airport System

The current deficit situation of the Spanish airport system suggests the need to manage this in a more efficient and profitable way. One of the possible options is through private management and being able to do this through Public Private Partnerships (PPP). This study analyzes the situation of the sector and its economic importance and the different possibilities for introducing private management in a public company, specifying the situation in the case of airports, presenting the advantages and disadvantages of these possibilities, and aiming at results obtained in other places where it has been applied. It is proposed that the ideal model for the introduction of private management would be through PPP models tailored to each airport, but having common characteristics according to the group they belong to. Finally, we observe that not all airports are commercially attractive, so that the PPP concept does not apply to all of them. In some cases even the operability itself is not viable at all, and that should be considered separately in order to avoid creating a private monopoly while trying to enhance competition among them.

Proposal for the Conceptual Design of Aeronautical Final Assembly Lines Based on the Industrial Digital Mock-Up Concept

The design of a Final Assembly Line (FAL) is carry out in the product industrialization activity. The phase dealing with the definition of conceptual solutions is characterized by depending heavily on the personnel experience and being time-consuming. To enhance such process, it is proposed a development of a knowledge based software application to assist designers in the definition of scenarios and to generate conceptual FAL alternatives. Both the scenario and the generated FAL solution are part of the industrialization digital mock-up (IDMU). A commercial software application used in the aircraft programmes and supporting the IDMU concepts of: Product, Process and Resource; was selected to implement a software prototype. This communication presents the adopted methodological approach and the architecture of the developed application.

A new label fusion method using graph cuts: application to hippocampus segmentation

The aim of this paper is to develop a probabilistic modeling framework for the segmentation of structures of interest from a collection of atlases. Given a subset of registered atlases into the target image for a particular Region of Interest (ROI), a statistical model of appearance and shape is computed for fusing the labels. Segmentations are obtained by minimizing an energy function associated with the proposed model, using a graph-cut technique. We test different label fusion methods on publicly available MR images of human brains.

Diseño de instrumentos para configurar una política industrial en España basada en los postulados de la economía evolutiva

La evidencia empírica aplicada a países de cierto tamaño y desarrollo económico, muestra que existe una relación directa y positiva entre la intensidad de la industria manufacturera, medida como porcentaje de su PIB, y ciertas variables económicas como, el crecimiento, el desempleo y la balanza exterior de bienes y servicios. En el caso de esta última, se verifica empíricamente, que los países con una proporción de actividad manufacturera inferior al 20%, tienen una marcada tendencia a presentar déficits crónicos de balanza de bienes y servicios, lo que conduce a persistentes déficits por cuenta corriente, al ser el primer déficit el principal componente del segundo. Esto trae consigo un continuado incremento del endeudamiento externo que no cesa, y que terminará en algún momento por desequilibrar el conjunto de la economía de los países con esos déficits crónicos. Las anteriores conclusiones, abren una vía de orientación de la política económica, que tiene como objetivo la promoción de la industria manufacturera de cada país. Y esto es un hecho ya en 2014. Países relevantes, como Alemania o Francia en la UE, incluso los EEUU y últimamente el Reino Unido, y por supuesto países del área asiática como Japón, Corea del Sur y China, llevan años promoviendo su industria manufacturera. Resulta significativo, que el debate ideológico sobre la bondad de la aplicación política industrial por parte de los gobiernos, frente a las teorías liberales de mantener a los poderes públicos lejos de ese tipo de actividades, haya dado paso a un modelo generalizado de corte más bien horizontal, donde los países casi sin excepciones apoyan el desarrollo de sus empresas con numerosos instrumentos, que van bastante más lejos de los habituales de I+D. Se valora por tanto, la industria manufacturera como algo vital para el equilibrio económico. Incluso la UE, defensora durante décadas de la no intervención de los diferentes Estados miembros en actividades de promoción industrial más allá del apoyo a las actividades de I+D, realiza un giro copernicano, que termina en 2012 proclamando que la industria manufacturera es vital para el equilibrio económico de la UE, que hay que promoverla, e incluso marca un objetivo, precisamente del 20%, como contribución manufacturera a su PIB. Es decir, se da por asumido que los servicios no son un sustituto indefinido de la industria y que por tanto tienen un límite, lo que se contrapone frontalmente contra la anterior creencia de que el aumento de la participación de los servicios en la economía, no solo era bueno, sino un síntoma de desarrollo. Esta premisa ya ha dejado de ser cierta para esos y otros países. En cambio, en España nada de esto sucede en las dos últimas décadas, sino que la industria manufacturera no recibe especial atención de los poderes públicos y se desliza en una pendiente de disminución de su contribución al PIB, que incluso se acelera con la crisis económica que comienza en 2007, hasta alcanzar cifras del orden del 12% del PIB en 2013. La política económica que se aplica es la de la deflación de costes, con los efectos consecuentes sobre los salarios y sobre la capacidad de la economía de generar riqueza. Se apuesta por un modelo de mano de obra barata, que recuerda al de los años 60. Como indicador relevante de esta situación, lo que exporta la industria manufacturera española, no ha ganado en contenido tecnológico en los últimos quince años. Esta situación se ve empeorada por un hecho significativo adicional, y es que casi el 40% de las ventas de la industria manufacturera española provienen de empresas de propiedad extranjera, con lo que eso supone por una parte de dependencia tecnológica del exterior como en el caso del automóvil, y de incertidumbre sobre su futuro, al estar basadas en el mantenimiento en el futuro de una mano de obra barata, que frenará que los españoles que trabajan en esas empresas, progresen económicamente. La propuesta de esta Tesis, es en cambio apostar por un modelo de crecimiento para España que tenga como uno de sus pilares el desarrollo de una industria manufacturera sólida y con cada vez mayor contenido tecnológico. Para ello, se propone un Plan de política industrial, donde se incluye la creación de actores impulsores de este plan, que deben ser del máximo nivel político. Si los diferentes gobiernos no entienden y asumen esta necesidad de apoyo a la industria a largo plazo e independiente de los cambios políticos, no será posible llevar a cabo este Plan. Para su puesta en marcha, se propone la creación o refuerzo de numerosos instrumentos de apoyo a la industria manufacturera de carácter fundamentalmente horizontal que van mucho más allá de los habituales del I+D, y que en varios casos, tienen una clara semejanza con otros existentes ya en otros países desarrollados desde hace años. La promoción de la industria manufacturera necesita nuevos instrumentos, como una financiación a largo plazo para las empresas, una promoción ordenada y eficaz de la actividad internacional de las empresas exportadoras, la mayoría de las cuales exportan productos manufacturados, una educación y formación profesional que esté alineada con estos objetivos, unos instrumentos que apoyen en especial el desarrollo la industria manufacturera, o la participación minoritaria pero significativa, del Estado en empresas españolas pertenecientes a sectores estratégicos entre otros. En resumen, esta Tesis propone una alternativa de política económica radicalmente diferente a la de dejar la industria manufacturera española a su suerte, y basar el futuro económico de España en una mano de obra barata. ABSTRACT The empirical evidence, applied to countries of certain size and economic development, shows that there exists a direct and positive relationship between industrial manufacturing activity, measured as a percentage of GDP, and certain economic variables, such as growth, unemployment and the foreign balance of trade. In the case of the latter, it is verified empirically that the countries with a percentage of manufacturing activity below 20% have a marked tendency for chronic deficits of the balance of trade, leading to persistent deficits in the current account, being that the former deficit is the main component of the latter. This brings about a continued increase in foreign debt that does not cease, and that will end at some point by disrupting the economy of the countries with these chronic deficits. The previous conclusions open the way to a new direction for economic policy, which promotes industrial manufacturing in each country. This is already a fact in 2014. Relevant countries, such as Germany or France in the EU, even the US and ultimately the UK, and of course countries of East Asia such as Japan, South Korea and China, have been promoting their industrial manufacturing for years. It becomes significant that the ideological debate about the goodwill of the application of industrial policy by governments, against liberal theories that maintain public powers far from these kinds of activities, has taken a step towards a horizontal-cut generalized model, where countries, with almost no exception, rely on various instruments to develop their companies that go much further than the usual R&D. Industrial manufacture is therefore valued as vital for economic stability. Even the EU, proponent for decades of non-intervention policy that goes beyond R&D, has gone full circle, ending in 2012 by proclaiming that industrial manufacture is vital for the economic stability of the EU, that it must be promoted. They even mark precisely 20% as an objective for manufacturing as a percentage of GDP. In other words, it is a given that services are not an indefinite substitute for industry, and that therefore it has a limit as such. This rejects the notion that the increase in services at the cost of manufacture is not only healthy, but is also a symptom of development. This premise is no longer true for these and other countries. On the other hand, none of this happens in Spain, where industrial manufacture receives no special attention from the public authorities, and it slides on a downward slope of percentage contribution to GDP, which accelerates the economic crisis that begins in 2007, until manufacture reaches values of around 12% of GDP in 2013. The economic policy applied is that of cost deflation, with consequential effects on wages and the capacity of the economy to generate wealth. A model is proposed for cheaper labor, akin to that of the 1960s. As a relevant indicator of this situation, manufacturing exports from Spain have not grown technologically in the last 15 years. The situation is made worse by another significant fact: almost 40% of sales of the manufacturing industry originate from companies of foreign origin, which supposes on one hand a technological dependence on foreign countries, such as in the case of the automotive industry, and on the other hand uncertainty in its future, being that they are based on maintaining cheap labor in the future, which will slow economic progress of Spaniards working in these companies. The proposition of this Thesis is to bet on a growth model for Spain that has as one of its pillars the development of a solid manufacturing industry, with increasing technological content. For this, an industrial policy plan is proposed, which includes the creation of driving agents for this plan, which must be of maximum political level. If the various governments don’t understand and assume this necessity for support of industry in the long term, independent of political change, this plan will not be accomplished. To start it, the creation or reinforcement of numerous instruments to promote the manufacturing activities are proposed, with a fundamentally horizontal nature that goes far beyond the usual R&D, and that, in several cases, have a clear similarity with others existing in other countries, having been developed for years. The promotion of the manufacturing industry needs new instruments, such as the long-term financing of companies, an orderly and efficient promotion of international activity of exporting companies, the most of which export manufactured goods, education and professional training which is in tune with these objectives, some instruments which support in particular the development of the manufacturing industry, or the minor yet significant participation of the State in Spanish companies belonging to strategic sectors, among others. In summary, this Thesis proposes an different alternative to the economic policy of leaving the manufacturing industry of Spain to its chances, and to base the economic future of Spain on a cheaper labor force.

Guiding functional connectivity estimation by structural connectivity in MEG: an application to discrimination of mild cognitive impaired conditions

Whole brain resting state connectivity is a promising biomarker that might help to obtain an early diagnosis in many neurological diseases, such as dementia. Inferring resting-state connectivity is often based on correlations, which are sensitive to indirect connections, leading to an inaccurate representation of the real backbone of the network. The precision matrix is a better representation for whole brain connectivity, as it considers only direct connections. The network structure can be estimated using the graphical lasso (GL), which achieves sparsity through l1-regularization on the precision matrix. In this paper, we propose a structural connectivity adaptive version of the GL, where weaker anatomical connections are represented as stronger penalties on the corre- sponding functional connections. We applied beamformer source reconstruction to the resting state MEG record- ings of 81 subjects, where 29 were healthy controls, 22 were single-domain amnestic Mild Cognitive Impaired (MCI), and 30 were multiple-domain amnestic MCI. An atlas-based anatomical parcellation of 66 regions was ob- tained for each subject, and time series were assigned to each of the regions. The fiber densities between the re- gions, obtained with deterministic tractography from diffusion-weighted MRI, were used to define the anatomical connectivity. Precision matrices were obtained with the region specific time series in five different frequency bands. We compared our method with the traditional GL and a functional adaptive version of the GL, in terms of log-likelihood and classification accuracies between the three groups. We conclude that introduc- ing an anatomical prior improves the expressivity of the model and, in most cases, leads to a better classification between groups.

A knowledge based application for industrialization design

After being designed, a product has to be manufactured, which means converting concepts and information into a real, physical object. This requires a big amount of resources and a careful planning. The product manufacturing must be designed too, and that is called Industrialization Design. An accepted methodology for this activity is starting defining simple structures and then progressively increasing the detail degree of the manufacturing solution. The impact of decisions taken at first stages of Industrialization Design is remarkable, and software tools to assist designers are required. In this paper a Knowledge Based Application prototype for the Industrialization Design is presented. The application is implemented within the environment CATIA V5/DELMIA. A case study with a simple Product from aerospace sector illustrates the prototype development.

Towards downscaling of aerosol gridded dataset for improving solar resource assessment, an application to Spain

Solar radiation estimates with clear sky models require estimations of aerosol data. The low spatial resolution of current aerosol datasets, with their remarkable drift from measured data, poses a problem in solar resource estimation. This paper proposes a new downscaling methodology by combining support vector machines for regression (SVR) and kriging with external drift, with data from the MACC reanalysis datasets and temperature and rainfall measurements from 213 meteorological stations in continental Spain. The SVR technique was proven efficient in aerosol variable modeling. The Linke turbidity factor (TL) and the aerosol optical depth at 550 nm (AOD 550) estimated with SVR generated significantly lower errors in AERONET positions than MACC reanalysis estimates. The TL was estimated with relative mean absolute error (rMAE) of 10.2% (compared with AERONET), against the MACC rMAE of 18.5%. A similar behavior was seen with AOD 550, estimated with rMAE of 8.6% (compared with AERONET), against the MACC rMAE of 65.6%. Kriging using MACC data as an external drift was found useful in generating high resolution maps (0.05° × 0.05°) of both aerosol variables. We created high resolution maps of aerosol variables in continental Spain for the year 2008. The proposed methodology was proven to be a valuable tool to create high resolution maps of aerosol variables (TL and AOD 550). This methodology shows meaningful improvements when compared with estimated available databases and therefore, leads to more accurate solar resource estimations. This methodology could also be applied to the prediction of other atmospheric variables, whose datasets are of low resolution.

Estructuras óptimas de detección y corrección de errores dirigidas a computadores construidos con lógica de alto nivel de Integración: aplicación industrial

Este trabajo trata de la aplicación de los códigos detectores y correctores de error al diseño de los Computadores Tolerantes a Fallos, planteando varias estrategias óptimas de detección y corrección para algunos subsistemas. En primer lugar,"se justifica la necesidad de aplicar técnicas de Tolerancia a Fallos. A continuación se hacen previsiones de evolución de la tecnología de Integración, así como una tipificación de los fallos en circuitos Integrados. Partiendo de una recopilación y revisión de la teoría de códigos, se hace un desarrollo teórico cuya aplicación permite obligar a que algunos de estos códigos sean cerrados respecto de las operaciones elementales que se ejecutan en un computador. Se plantean estrategias óptimas de detección y corrección de error para sus subsistemas mas Importantes, culminando en el diseño, realización y prueba de una unidad de memoria y una unidad de proceso de datos con amplias posibilidades de detección y corrección de errores.---ABSTRACT---The present work deals with the application of error detecting and correctíng codes to the désign of Fault Tolerant Computers. Several óptimo» detection and correction strategies are presented to be applied in some subsystems. First of all, the necessity of applying Fault Tolerant techniques is explained. Later, a study on íntegration technology evolution and typification of Integrated circuit faults 1s developed. Based on a compilation and revisión of Coding Theory, a theoretical study is carried out. It allows us to force some of these codes to be closed over elementary operations. Optimum detection and correction techniques are presented for the raost important subsystems. Flnally, the design, building and testing of a memory unit and a processing unit provided with wlde error detection and correction posibilities 1s shown.