Analysis of the geometric altimetry to support aircraft optimal trajectories within the future 4d trajectory management

Over the past few years, the common practice within air traffic management has been that commercial aircraft fly by following a set of predefined routes to reach their destination. Currently, aircraft operators are requesting more flexibility to fly according to their prefer- ences, in order to achieve their business objectives. Due to this reason, much research effort is being invested in developing different techniques which evaluate aircraft optimal trajectory and traffic synchronisation. Also, the inefficient use of the airspace using barometric altitude overall in the landing and takeoff phases or in Continuous Descent Approach (CDA) trajectories where currently it is necessary introduce the necessary reference setting (QNH or QFE). To solve this problem and to permit a better airspace management born the interest of this research. Where the main goals will be to evaluate the impact, weakness and strength of the use of geometrical altitude instead of the use of barometric altitude. Moreover, this dissertation propose the design a simplified trajectory simulator which is able to predict aircraft trajectories. The model is based on a three degrees of freedom aircraft point mass model that can adapt aircraft performance data from Base of Aircraft Data, and meteorological information. A feature of this trajectory simulator is to support the improvement of the strategic and pre-tactical trajectory planning in the future Air Traffic Management. To this end, the error of the tool (aircraft Trajectory Simulator) is measured by comparing its performance variables with actual flown trajectories obtained from Flight Data Recorder information. The trajectory simulator is validated by analysing the performance of different type of aircraft and considering different routes. A fuel consumption estimation error was identified and a correction is proposed for each type of aircraft model. In the future Air Traffic Management (ATM) system, the trajectory becomes the fundamental element of a new set of operating procedures collectively referred to as Trajectory-Based Operations (TBO). Thus, governmental institutions, academia, and industry have shown a renewed interest for the application of trajectory optimisation techniques in com- mercial aviation. The trajectory optimisation problem can be solved using optimal control methods. In this research we present and discuss the existing methods for solving optimal control problems focusing on direct collocation, which has received recent attention by the scientific community. In particular, two families of collocation methods are analysed, i.e., Hermite-Legendre-Gauss-Lobatto collocation and the pseudospectral collocation. They are first compared based on a benchmark case study: the minimum fuel trajectory problem with fixed arrival time. For the sake of scalability to more realistic problems, the different meth- ods are also tested based on a real Airbus 319 El Cairo-Madrid flight. Results show that pseudospectral collocation, which has shown to be numerically more accurate and computa- tionally much faster, is suitable for the type of problems arising in trajectory optimisation with application to ATM. Fast and accurate optimal trajectory can contribute properly to achieve the new challenges of the future ATM. As atmosphere uncertainties are one of the most important issues in the trajectory plan- ning, the final objective of this dissertation is to have a magnitude order of how different is the fuel consumption under different atmosphere condition. Is important to note that in the strategic phase planning the optimal trajectories are determined by meteorological predictions which differ from the moment of the flight. The optimal trajectories have shown savings of at least 500 [kg] in the majority of the atmosphere condition (different pressure, and temperature at Mean Sea Level, and different lapse rate temperature) with respect to the conventional procedure simulated at the same atmosphere condition.This results show that the implementation of optimal profiles are beneficial under the current Air traffic Management (ATM).

Pulse-Shape Analysis of PDM-QPSK Modulation Formats for 100 and 200 Gb/s DWDM transmissions

Advanced optical modulation format polarization-division multiplexed quadrature phase shift keying (PDM-QPSK) has become a key ingredient in the design of 100 and 200-Gb/s dense wavelength-division multiplexed (DWDM) networks. The performance of this format varies according to the shape of the pulses employed by the optical carrier: non-return to zero (NRZ), return to zero (RZ) or carrier-suppressed return to zero (CSRZ). In this paper we analyze the tolerance of PDM-QPSK to linear and nonlinear optical impairments: amplified spontaneous emission (ASE) noise, crosstalk, distortion by optical filtering, chromatic dispersion (CD), polarization mode dispersion (PMD) and fiber Kerr nonlinearities. RZ formats with a low duty cycle value reduce pulse-to-pulse interaction obtaining a higher tolerance to CD, PMD and intrachannel nonlinearities.

Analysis of the impact of globalization and economic growth on food security in developing countries

A pesar de los importantes avances en la reducción del hambre, la seguridad alimentaria continúa siendo un reto de dimensión internacional. La seguridad alimentaria es un concepto amplio y multidimensional, cuyo análisis abarca distintas escalas y horizontes temporales. Dada su complejidad, la identificación de las causas de la inseguridad alimentaria y la priorización de las medias para abordarlas, son dos cuestiones que suscitan un intenso debate en la actualidad. El objetivo de esta tesis es evaluar el impacto de la globalización y el crecimiento económico en la seguridad alimentaria en los países en desarrollo, desde una perspectiva macro y un horizonte temporal a largo plazo. La influencia de la globalización se aborda de una manera secuencial. En primer lugar, se analiza la relación entre la inversión público-privada en infraestructuras y las exportaciones agrarias. A continuación, se estudia el impacto de las exportaciones agrarias en los indicadores de seguridad alimentaria. El estudio del impacto del crecimiento económico aborda los cambios paralelos en la distribución de la renta, y cómo la inequidad influye en el comportamiento de la seguridad alimentaria nacional. Además, se analiza en qué medida el crecimiento económico contribuye a acelerar el proceso de mejora de la seguridad alimentaria. Con el fin de conseguir los objetivos mencionados, se llevan a cabo varios análisis econométricos basados en datos de panel, en el que se combinan datos de corte transversal de 52 países y datos temporales comprendidos en el periodo 1991-2012. Se analizan tanto variables en niveles como variables en tasas de cambio anual. Se aplican los modelos de estimación de efectos variables y efectos fijos, ambos en niveles y en primeras diferencias. La tesis incluye cuatro tipos de modelos econométricos, cada uno de ellos con sus correspondientes pruebas de robustez y especificaciones. Los resultados matizan la importancia de la globalización y el crecimiento económico como mecanismos de mejora de la seguridad alimentaria en los países en desarrollo. Se obtienen dos conclusiones relativas a la globalización. En primer lugar, los resultados sugieren que la promoción de las inversiones privadas en infraestructuras contribuye a aumentar las exportaciones agrarias. En segundo lugar, se observa que las exportaciones agrarias pueden tener un impacto negativo en los indicadores de seguridad alimentaria. La combinación de estas dos conclusiones sugiere que la apertura comercial y financiera no contribuye por sí misma a la mejora de la seguridad alimentaria en los países en desarrollo. La apertura internacional de los países en desarrollo ha de ir acompañada de políticas e inversiones que desarrollen sectores productivos de alto valor añadido, que fortalezcan la economía nacional y reduzcan su dependencia exterior. En relación al crecimiento económico, a pesar del incuestionable hecho de que el crecimiento económico es una condición necesaria para reducir los niveles de subnutrición, no es una condición suficiente. Se han identificado tres estrategias adicionales que han de acompañar al crecimiento económico con el fin de intensificar su impacto positivo sobre la subnutrición. Primero, es necesario que el crecimiento económico sea acompañado de una distribución más equitativa de los ingresos. Segundo, el crecimiento económico ha de reflejarse en un aumento de inversiones en salud, agua y saneamiento y educación. Se observa que, incluso en ausencia de crecimiento económico, mejoras en el acceso a agua potable contribuyen a reducir los niveles de población subnutrida. Tercero, el crecimiento económico sostenible en el largo plazo parece tener un mayor impacto positivo sobre la seguridad alimentaria que el crecimiento económico más volátil o inestable en el corto plazo. La estabilidad macroeconómica se identifica como una condición necesaria para alcanzar una mayor mejora en la seguridad alimentaria, incluso habiéndose mejorado la equidad en la distribución de los ingresos. Por último, la tesis encuentra que los países en desarrollo analizados han experimentado diferentes trayectorias no lineales en su proceso de mejora de sus niveles de subnutrición. Los resultados sugieren que un mayor nivel inicial de subnutrición y el crecimiento económico son responsables de una respuesta más rápida al reto de la mejora de la seguridad alimentaria. ABSTRACT Despite the significant reductions of hunger, food security still remains a global challenge. Food security is a wide concept that embraces multiple dimensions, and has spatial-temporal scales. Because of its complexity, the identification of the drivers underpinning food insecurity and the prioritization of measures to address them are a subject of intensive debate. This thesis attempts to assess the impact of globalization and economic growth on food security in developing countries with a macro level scale (country) and using a long-term approach. The influence of globalization is addressed in a sequential way. First, the impact of public-private investment in infrastructure on agricultural exports in developing countries is analyzed. Secondly, an assessment is conducted to determine the impact of agricultural exports on food security indicators. The impact of economic growth focuses on the parallel changes in income inequality and how the income distribution influences countries' food security performance. Furthermore, the thesis analyzes to what extent economic growth helps accelerating food security improvements. To address the above mentioned goals, various econometric models are formulated. Models use panel data procedures combining cross-sectional data of 52 countries and time series data from 1991 to 2012. Yearly data are expressed both in levels and in changes. The estimation models applied are random effects estimation and fixed effects estimations, both in levels and in first differences. The thesis includes four families of econometric models, each with its own set of robustness checks and specifications. The results qualify the relevance of globalization and economic growth as enabling mechanisms for improving food security in developing countries. Concerning globalization, two main conclusions can be drawn. First, results showed that enhancing foreign private investment in infrastructures contributes to increase agricultural exports. Second, agricultural exports appear to have a negative impact on national food security indicators. These two conclusions suggest that trade and financial openness per se do not contribute directly to improve food security in development countries. Both measures should be accompanied by investments and policies to support the development of national high value productive sectors, to strengthen the domestic economy and reduce its external dependency. Referring to economic growth, despite the unquestionable fact that income growth is a pre-requisite for reducing undernourishment, results suggest that it is a necessary but not a sufficient condition. Three additional strategies should accompany economic growth to intensifying its impact on food security. Firstly, it is necessary that income growth should be accompanied by a better distribution of income. Secondly, income growth needs to be followed by investments and policies in health, sanitation and education to improve food security. Even if economic growth falters, sustained improvements in the access to drinking water may still give rise to reductions in the percentage of undernourished people. And thirdly, long-term economic growth appears to have a greater impact on reducing hunger than growth regimes that combine periods of growth peaks followed by troughs. Macroeconomic stability is a necessary condition for accelerating food security. Finally, the thesis finds that the developing countries analyzed have experienced different non-linear paths toward improving food security. Results also show that a higher initial level of undernourishment and economic growth result in a faster response for improving food security.

Code assessment and modelling for Design Basis Accident analysis of the European Sodium Fast Reactor design. Part II: Optimised core and representative transients analysis

The new reactor concepts proposed in the Generation IV International Forum require the development and validation of computational tools able to assess their safety performance. In the first part of this paper the models of the ESFR design developed by several organisations in the framework of the CP-ESFR project were presented and their reliability validated via a benchmarking exercise. This second part of the paper includes the application of those tools for the analysis of design basis accident (DBC) scenarios of the reference design. Further, this paper also introduces the main features of the core optimisation process carried out within the project with the objective to enhance the core safety performance through the reduction of the positive coolant density reactivity effect. The influence of this optimised core design on the reactor safety performance during the previously analysed transients is also discussed. The conclusion provides an overview of the work performed by the partners involved in the project towards the development and enhancement of computational tools specifically tailored to the evaluation of the safety performance of the Generation IV innovative nuclear reactor designs.

A comparative analysis of configurations of linear Fresnel collectors for concentrating solar power

Linear Fresnel collector arrays present some relevant advantages in the domain of concentrating solar power because of their simplicity, robustness and low capital cost. However, they also present important drawbacks and limitations, notably their average concentration ratio, which seems to limit significantly the performance of these systems. First, the paper addresses the problem of characterizing the mirror field configuration assuming hourly data of a typical year, in reference to a configuration similar to that of Fresdemo. For a proper comparative study, it is necessary to define a comparison criterion. In that sense, a new variable is defined, the useful energy efficiency, which only accounts for the radiation that impinges on the receiver with intensities above a reference value. As a second step, a comparative study between central linear Fresnel reflectors and compact linear Fresnel reflectors is carried out. This analysis shows that compact linear Fresnel reflectors minimize blocking and shading losses compared to a central configuration. However this minimization is not enough to overcome other negative effects of the compact Fresnel collectors, as the greater dispersion of the rays reaching the receiver, caused by the fact that mirrors must be located farther from the receiver, which yields to lower efficiencies.

Singularities in DROMO formulation. Analysis of deep flybys

The singularities in Dromo are characterized in this paper, both from an analytical and a numerical perspective. When the angular momentum vanishes, Dromo may encounter a singularity in the evolution equations. The cancellation of the angular momentum occurs in very speci?c situations and may be caused by the action of strong perturbations. The gravitational attraction of a perturbing planet may lead to rapid changes in the angular momentum of the particle. In practice, this situation may be encountered during deep planetocentric ?ybys. The performance of Dromo is evaluated in di?erent scenarios. First, Dromo is validated for integrating the orbit of Near Earth Asteroids. Resulting errors are of the order of the diameter of the asteroid. Second, a set of theoretical ?ybys are designed for analyzing the performance of the formulation in the vicinity of the singularity. New sets of Dromo variables are proposed in order to minimize the dependency of Dromo on the angular momentum. A slower time scale is introduced, leading to a more stable description of the ?yby phase. Improvements in the overall performance of the algorithm are observed when integrating orbits close to the singularity.

Cross-analysis of Transversal Competences in Project Management

This paper presents a framework for project management competence assessment based on participant’s performance and contribution in a simulated environment. The proposed framework considers competence assessment through evidences and the participation of different roles. The system enforces the assessment of individual competences by means of a set of performance indicators. A specific case study is presented and the relationship between exhibited transversal competences and project quality is analysed.

Análisis cuantitativo y cualitativo de los momentos críticos en baloncesto = Quantitative and qualitative analysis of the critical moments in basketball

El MC en baloncesto es aquel fenómeno relacionado con el juego que presenta unas características particulares determinadas por la idiosincrasia de un equipo y puede afectar a los protagonistas y por ende al devenir del juego. En la presente Tesis se ha estudiado la incidencia del MC en Liga A.C.B. de baloncesto y para su desarrollo en profundidad se ha planteado dos investigaciones una cuantitativa y otra cualitativa cuya metodología se detalla a continuación: La investigación cuantitativa se ha basado en la técnica de estudio del “Performance analysis”, para ello se han estudiado cuatro temporadas de la Liga A.C.B. (del 2007/08 al 2010/11), tal y como refleja en la bibliografía consultada se han tomado como momentos críticos del juego a los últimos cinco minutos de partidos donde la diferencia de puntos fue de seis puntos y todos los Tiempos Extras disputados, de tal manera que se han estudiado 197 momentos críticos. La contextualización del estudio se ha hecho en función de la variables situacionales “game location” (local o visitante), “team quality” (mejores o peores clasificados) y “competition” (fases de LR y Playoff). Para la interpretación de los resultados se han realizado los siguientes análisis descriptivos: 1) Análisis Discriminante, 2) Regresión Lineal Múltiple; y 3) Análisis del Modelo Lineal General Multivariante. La investigación cualitativa se ha basado en la técnica de investigación de la entrevista semiestructurada. Se entrevistaron a 12 entrenadores que militaban en la Liga A.C.B. durante la temporada 2011/12, cuyo objetivo ha sido conocer el punto de vista que tiene el entrenador sobre el concepto del MC y que de esta forma pudiera dar un enfoque más práctico basado en su conocimiento y experiencia acerca de cómo actuar ante el MC en el baloncesto. Los resultados de ambas investigaciones coinciden en señalar la importancia del MC sobre el resultado final del juego. De igual forma, el concepto en sí entraña una gran complejidad por lo que se considera fundamental la visión científica de la observación del juego y la percepción subjetiva que presenta el entrenador ante el fenómeno, para la cual los aspectos psicológicos de sus protagonistas (jugadores y entrenadores) son determinantes. ABSTRACT The Critical Moment (CM) in basketball is a related phenomenon with the game that has particular features determined by the idiosyncrasies of a team and can affect the players and therefore the future of the game. In this Thesis we have studied the impact of CM in the A.C.B. League and from a profound development two investigations have been raised, quantitative and qualitative whose methodology is as follows: The quantitative research is based on the technique of study "Performance analysis", for this we have studied four seasons in the A.C.B. League (2007/08 to 2010/11), and as reflected in the literature the Critical Moments of the games were taken from the last five minutes of games where the point spread was six points and all overtimes disputed, such that 197 critical moments have been studied. The contextualization of the study has been based on the situational variables "game location" (home or away), "team quality" (better or lower classified) and "competition" (LR and Playoff phases). For the interpretation of the results the following descriptive analyzes were performed: 1) Discriminant Analysis, 2) Multiple Linear Regression Analysis; and 3) Analysis of Multivariate General Linear Model. Qualitative research is based on the technique of investigation of a semi-structured interview. 12 coaches who belonged to the A.C.B. League were interviewed in seasons 2011/12, which aimed to determine the point of view that the coach has on the CM concept and thus could give a more practical approach based on their knowledge and experience about how to deal with the CM in basketball. The results of both studies agree on the importance of the CM on the final outcome of the game. Similarly, the concept itself is highly complex so the scientific view of the observation of the game is considered essential as well as the subjective perception the coach presents before the phenomenon, for which the psychological aspects of their characters (players and coaches) are crucial.

Environmental analysis of a Concentrated Solar Power (CSP) plant hybridised with different fossil and renewable fuels

The environmental performance of a 50 MW parabolic trough Concentrated Solar Power (CSP) plant hybridised with different fuels was determined using a Life Cycle Assessment methodology. Six different scenarios were investigated, half of which involved hybridisation with fossil fuels (natural gas, coal and fuel oil), and the other three involved hybridisation with renewable fuels (wheat straw, wood pellets and biogas). Each scenario was compared to a solar-only operation. Nine different environmental categories as well as the Cumulative Energy Demand and the Energy Payback Time (EPT) were evaluated using Simapro software for 1 MWh of electricity produced. The results indicate a worse environmental performance for a CSP plant producing 12% of the electricity from fuel than in a solar-only operation for every indicator, except for the eutrophication and toxicity categories, whose results for the natural gas scenario are slightly better. In the climate change category, the results ranged between 26.9 and 187 kg CO2 eq/MWh, where a solar-only operation had the best results and coal hybridisation had the worst. Considering a weighted single score indicator, the environmental impact of the renewable fuels scenarios is approximately half of those considered in fossil fuels, with the straw scenario showing the best results, and the coal scenario the worstones. EPT for solar-only mode is 1.44 years, while hybridisation scenarios EPT vary in a range of 1.72 -1.83 years for straw and pellets respectively. The fuels with more embodied energy are biomethane and wood pellets.

Analysis of air flow past and through the 2415-3S airfoil for an unmanned aerial vehicle with internal propulsion system

This paper deals with the prediction of velocity fields on the 2415-3S airfoil which will be used for an unmanned aerial vehicle with internal propulsion system and in this way analyze the air flow through an internal duct of the airfoil using computational fluid dynamics. The main objective is to evaluate the effect of the internal air flow past the airfoil and how this affects the aerodynamic performance by means of lift and drag forces. For this purpose, three different designs of the internal duct were studied; starting from the base 2415-3S airfoil developed in previous investigation, basing on the hypothesis of decreasing the flow separation produced when the propulsive airflow merges the external flow, and in this way obtaining the best configuration. For that purpose, an exhaustive study of the mesh sensitivity was performed. It was used a non-structured mesh since the computational domain is three-dimensional and complex. The selected mesh contains approximately 12.5 million elements. Both the computational domain and the numerical solution were made with commercial CAD and CFD software, respectively. Air, incompressible and steady was analyzed. The boundary conditions are in concordance with experimental setup in the AF 6109 wind tunnel. The k-e model is utilized to describe the turbulent flow process as followed in references. Results allowed obtaining velocity contours as well as lift and drag coefficients and also the location of separation and reattachment regions in some cases for zero degrees of angle of attack on the internal and external surfaces of the airfoil. Finally, the selection of the configuration with the best aerodynamic performance was made, selecting the option without curved baffles.

Numerical analysis of air flow past the 2415-3S airfoil for an unmanned aerial vehicle with internal propulsion system

This paper deals with the prediction of pressure and velocity fields on the 2415-3S airfoil which will be used for and unmanned aerial vehicle with internal propulsion system and in this way analyze the air flow through an internal duct of the airfoil using computational fluid dynamics. The main objective is to evaluate the effect of the internal air flow past the airfoil and how this affects the aerodynamic performance by means of lift and drag forces. For this purpose, three different designs of the internal duct were studied; starting from the base 2415-3S airfoil developed in previous investigation, basing on the hypothesis of decreasing the flow separation produced when the propulsive airflow merges the external flow, and in this way obtaining the best configuration. For that purpose, an exhaustive study of the mesh sensitivity was performed. It was used a non-structured mesh since the computational domain is tridimensional and complex. The selected mesh contains approximately 12.5 million elements. Both the computational domain and the numerical solution were made with commercial CAD and CFD software respectively. Air, incompressible and steady was analyzed. The boundary conditions are in concordance with experimental setup in the AF 6109 wind tunnel. The k-ε model is utilized to describe the turbulent flow process as followed in references. Results allowed obtaining pressure and velocity contours as well as lift and drag coefficients and also the location of separation and reattachment regions in some cases for zero degrees of angle of attack on the internal and external surfaces of the airfoil. Finally, the selection of the configuration with the best aerodynamic performance was made, selecting the option without curved baffles.

Multiscale analysis of the mechanical behavior of needle-punched nonwoven fabrics

Los fieltros son una familia de materiales textiles constituidos por una red desordenada de fibras conectadas por medio de enlaces térmicos, químicos o mecánicos. Presentan menor rigidez y resistencia (al igual que un menor coste de procesado) que sus homólogos tejidos, pero mayor deformabilidad y capacidad de absorción de energía. Los fieltros se emplean en diversas aplicaciones en ingeniería tales como aislamiento térmico, geotextiles, láminas ignífugas, filtración y absorción de agua, impacto balístico, etc. En particular, los fieltros punzonados fabricados con fibras de alta resistencia presentan una excelente resistencia frente a impacto balístico, ofreciendo las mismas prestaciones que los materiales tejidos con un tercio de la densidad areal. Sin embargo, se sabe muy poco acerca de los mecanismos de deformación y fallo a nivel microscópico, ni sobre como influyen en las propiedades mecánicas del material. Esta carencia de conocimiento dificulta la optimización del comportamiento mecánico de estos materiales y también limita el desarrollo de modelos constitutivos basados en mecanismos físicos, que puedan ser útiles en el diseño de componentes estructurales. En esta tesis doctoral se ha llevado a cabo un estudio minucioso con el fin de determinar los mecanismos de deformación y las propiedades mecánicas de fieltros punzonados fabricados con fibras de polietileno de ultra alto peso molecular. Los procesos de deformación y disipación de energía se han caracterizado en detalle por medio de una combinación de técnicas experimentales (ensayos mecánicos macroscópicos a velocidades de deformación cuasi-estáticas y dinámicas, impacto balístico, ensayos de extracción de una o múltiples fibras, microscopía óptica, tomografía computarizada de rayos X y difracción de rayos X de gran ángulo) que proporcionan información de los mecanismos dominantes a distintas escalas. Los ensayos mecánicos macroscópicos muestran que el fieltro presenta una resistencia y ductilidad excepcionales. El estado inicial de las fibras es curvado, y la carga se transmite por el fieltro a través de una red aleatoria e isótropa de nudos creada por el proceso de punzonamiento, resultando en la formación de una red activa de fibra. La rotación y el estirado de las fibras activas es seguido por el deslizamiento y extracción de la fibra de los puntos de anclaje mecánico. La mayor parte de la resistencia y la energía disipada es proporcionada por la extracción de las fibras activas de los nudos, y la fractura final tiene lugar como consecuencia del desenredo total de la red en una sección dada donde la deformación macroscópica se localiza. No obstante, aunque la distribución inicial de la orientación de las fibras es isótropa, las propiedades mecánicas resultantes (en términos de rigidez, resistencia y energía absorbida) son muy anisótropas. Los ensayos de extracción de múltiples fibras en diferentes orientaciones muestran que la estructura de los nudos conecta más fibras en la dirección transversal en comparación con la dirección de la máquina. La mejor interconectividad de las fibras a lo largo de la dirección transversal da lugar a una esqueleto activo de fibras más denso, mejorando las propiedades mecánicas. En términos de afinidad, los fieltros deformados a lo largo de la dirección transversal exhiben deformación afín (la deformación macroscópica transfiere directamente a las fibras por el material circundante), mientras que el fieltro deformado a lo largo de la dirección de la máquina presenta deformación no afín, y la mayor parte de la deformación macroscópica no es transmitida a las fibras. A partir de estas observaciones experimentales, se ha desarrollado un modelo constitutivo para fieltros punzonados confinados por enlaces mecánicos. El modelo considera los efectos de la deformación no afín, la conectividad anisótropa inducida durante el punzonamiento, la curvatura y re-orientación de la fibra, así como el desenredo y extracción de la fibra de los nudos. El modelo proporciona la respuesta de un mesodominio del material correspondiente al volumen asociado a un elemento finito, y se divide en dos bloques. El primer bloque representa el comportamiento de la red y establece la relación entre el gradiente de deformación macroscópico y la respuesta microscópica, obtenido a partir de la integración de la respuesta de las fibras en el mesodominio. El segundo bloque describe el comportamiento de la fibra, teniendo en cuenta las características de la deformación de cada familia de fibras en el mesodominio, incluyendo deformación no afín, estiramiento, deslizamiento y extracción. En la medida de lo posible, se ha asignado un significado físico claro a los parámetros del modelo, por lo que se pueden identificar por medio de ensayos independientes. Las simulaciones numéricas basadas en el modelo se adecúan a los resultados experimentales de ensayos cuasi-estáticos y balísticos desde el punto de vista de la respuesta mecánica macroscópica y de los micromecanismos de deformación. Además, suministran información adicional sobre la influencia de las características microstructurales (orientación de la fibra, conectividad de la fibra anisótropa, afinidad, etc) en el comportamiento mecánico de los fieltros punzonados. Nonwoven fabrics are a class of textile material made up of a disordered fiber network linked by either thermal, chemical or mechanical bonds. They present lower stiffness and strength (as well as processing cost) than the woven counterparts but much higher deformability and energy absorption capability and are used in many different engineering applications (including thermal insulation, geotextiles, fireproof layers, filtration and water absorption, ballistic impact, etc). In particular, needle-punched nonwoven fabrics manufactured with high strength fibers present an excellent performance for ballistic protection, providing the same ballistic protection with one third of the areal weight as compared to dry woven fabrics. Nevertheless, very little is known about their deformation and fracture micromechanisms at the microscopic level and how they contribute to the macroscopic mechanical properties. This lack of knowledge hinders the optimization of their mechanical performance and also limits the development of physically-based models of the mechanical behavior that can be used in the design of structural components with these materials. In this thesis, a thorough study was carried out to ascertain the micromechanisms of deformation and the mechanical properties of a needle-punched nonwoven fabric made up by ultra high molecular weight polyethylene fibers. The deformation and energy dissipation processes were characterized in detail by a combination of experimental techniques (macroscopic mechanical tests at quasi-static and high strain rates, ballistic impact, single fiber and multi fiber pull-out tests, optical microscopy, X-ray computed tomography and wide angle X-ray diffraction) that provided information of the dominant mechanisms at different length scales. The macroscopic mechanical tests showed that the nonwoven fabric presented an outstanding strength and energy absorption capacity. It was found that fibers were initially curved and the load was transferred within the fabric through the random and isotropic network of knots created by needlepunching, leading to the formation of an active fiber network. Uncurling and stretching of the active fibers was followed by fiber sliding and pull-out from the entanglement points. Most of the strength and energy dissipation was provided by the extraction of the active fibers from the knots and final fracture occurred by the total disentanglement of the fiber network in a given section at which the macroscopic deformation was localized. However, although the initial fiber orientation distribution was isotropic, the mechanical properties (in terms of stiffness, strength and energy absorption) were highly anisotropic. Pull-out tests of multiple fibers at different orientations showed that structure of the knots connected more fibers in the transverse direction as compared with the machine direction. The better fiber interconnection along the transverse direction led to a denser active fiber skeleton, enhancing the mechanical response. In terms of affinity, fabrics deformed along the transverse direction essentially displayed affine deformation {i.e. the macroscopic strain was directly transferred to the fibers by the surrounding fabric, while fabrics deformed along the machine direction underwent non-affine deformation, and most of the macroscopic strain was not transferred to the fibers. Based on these experimental observations, a constitutive model for the mechanical behavior of the mechanically-entangled nonwoven fiber network was developed. The model accounted for the effects of non-affine deformation, anisotropic connectivity induced by the entanglement points, fiber uncurling and re-orientation as well as fiber disentanglement and pull-out from the knots. The model provided the constitutive response for a mesodomain of the fabric corresponding to the volume associated to a finite element and is divided in two blocks. The first one was the network model which established the relationship between the macroscopic deformation gradient and the microscopic response obtained by integrating the response of the fibers in the mesodomain. The second one was the fiber model, which took into account the deformation features of each set of fibers in the mesodomain, including non-affinity, uncurling, pull-out and disentanglement. As far as possible, a clear physical meaning is given to the model parameters, so they can be identified by means of independent tests. The numerical simulations based on the model were in very good agreement with the experimental results of in-plane and ballistic mechanical response of the fabrics in terms of the macroscopic mechanical response and of the micromechanisms of deformation. In addition, it provided additional information about the influence of the microstructural features (fiber orientation, anisotropic fiber connectivity, affinity) on the mechanical performance of mechanically-entangled nonwoven fabrics.

Análisis cualitativo de la relación entrenador-deportista en etapas de formación en baloncesto = Qualitative analysis of the coach-athlete relationship in youth basketball

La relación entrenador-deportista estudia, dentro del ámbito de la psicología social en el deporte, la interacción de los comportamientos, sentimientos y emociones de ambos miembros de la pareja. Se entiende como un proceso en el que antecedentes como la edad, el género o las características esperadas en el otro condicionan el desarrollo de diferentes componentes, los cuales determinan la calidad de la relación, obteniéndose diferentes resultados tanto a nivel deportivo como personal. En la presente tesis se han estudiado 12 relaciones positivas entrenador-deportista en categorías de formación en baloncesto con el objetivo de conocer los condicionantes, componentes, estrategias y resultados de relaciones efectivas. Para ello, se ha realizado un estudio cualitativo, cuya muestra (N=24) se ha seleccionado de manera deliberada discriminando variables como el nivel deportivo del equipo, las características del entrenador, la duración y la calidad de la relación. Las 12 díadas participaban en el máximo nivel de su categoría, tenían una duración mínima de dos temporadas y fueron calificadas como positivas por los entrenadores principales. La investigación se ha llevado a cabo desde la perspectiva holística del fenómeno, teniendo en cuenta tanto el punto de vista del entrenador como el del jugador. Para la recogida de datos se utilizó la entrevista semiestructurada y en profundidad. Los resultados señalan la necesidad de desarrollar estrategias que promuevan y mantengan relaciones de calidad en baloncesto, ya que éstas tienen un alto impacto en el progreso deportivo y personal de los jugadores jóvenes en baloncesto. Entre los condicionantes de la relación entrenador-deportista se ha percibido que las expectativas formadas en los primeros contactos pueden determinar la calidad de la relación. Por otro lado, los componentes dan lugar a resultados como el crecimiento a nivel personal por parte de los jugadores o un mayor rendimiento deportivo, producido en gran medida por la satisfacción y el bienestar psicológico tanto del entrenador como del jugador. Por último, los resultados indican la importancia de adecuar el comportamiento del entrenador a las características propias de los jugadores en cada categoría de formación. ABSTRACT The coach-athlete relationship studies, within the field of social psychology in sport, the interaction of behavior, feelings and emotions in both partners. It is understood as a process in which antecedents such as age, gender or expectations develop different components. The quality of the relationship is determined by these three elements, leading to different results in sport performance as in personal variables. This thesis examined 12 positive coach-athlete rapports in youth basketball teams in order to better understand the determinants, components, strategies and outcomes of effective relationships. A qualitative study has been carried out. The sample (N = 24) is selected deliberately discriminating variables such as the team’s sportive level, coach characteristics, duration and quality of the relationship. Twelve dyads participated at the highest level in its category, had a minimum of two seasons and were rated as positive by head coaches. The research was conducted from a holistic perspective of the phenomenon, taking into account the point of view of both the coach and the player. Indepth semi-structured interview was used for data collection. The results report the need to develop strategies to promote and maintain high quality relationships in basketball, because they have an important impact in sport and personal development of young basketball players. Expectations raised through different impression cues in the first contacts can determine the quality of the relationship. On the other hand, the components lead to results such as players’ personal growth or sport performance, largely produced by the satisfaction and psychological well being of both the coach and the player. Finally, the results indicate the importance of adapting the coach’s behavior to the characteristics of the different stages of young athletes’ development.

Methodology for Dynamic Stability and Robustness Analysis of Commercial-Power-Module-Based DC-Distributed Systems

El propósito de esta tesis es presentar una metodología para realizar análisis de la dinámica en pequeña señal y el comportamiento de sistemas de alimentación distribuidos de corriente continua (CC), formados por módulos comerciales. Para ello se hace uso de un método sencillo que indica los márgenes de estabilidad menos conservadores posibles mediante un solo número. Este índice es calculado en cada una de las interfaces que componen el sistema y puede usarse para obtener un índice global que indica la estabilidad del sistema global. De esta manera se posibilita la comparación de sistemas de alimentación distribuidos en términos de robustez. La interconexión de convertidores CC-CC entre ellos y con los filtros EMI necesarios puede originar interacciones no deseadas que dan lugar a la degradación del comportamiento de los convertidores, haciendo el sistema más propenso a inestabilidades. Esta diferencia en el comportamiento se debe a interacciones entre las impedancias de los diversos elementos del sistema. En la mayoría de los casos, los sistemas de alimentación distribuida están formados por módulos comerciales cuya estructura interna es desconocida. Por ello los análisis presentados en esta tesis se basan en medidas de la respuesta en frecuencia del convertidor que pueden realizarse desde los terminales de entrada y salida del mismo. Utilizando las medidas de las impedancias de entrada y salida de los elementos del sistema, se puede construir una función de sensibilidad que proporciona los márgenes de estabilidad de las diferentes interfaces. En esta tesis se utiliza el concepto del valor máximo de la función de sensibilidad (MPC por sus siglas en inglés) para indicar los márgenes de estabilidad como un único número. Una vez que la estabilidad de todas las interfaces del sistema se han evaluado individualmente, los índices obtenidos pueden combinarse para obtener un único número con el que comparar la estabilidad de diferentes sistemas. Igualmente se han analizado las posibles interacciones en la entrada y la salida de los convertidores CC-CC, obteniéndose expresiones analíticas con las que describir en detalle los acoplamientos generados en el sistema. Los estudios analíticos realizados se han validado experimentalmente a lo largo de la tesis. El análisis presentado en esta tesis se culmina con la obtención de un índice que condensa los márgenes de estabilidad menos conservativos. También se demuestra que la robustez del sistema está asegurada si las impedancias utilizadas en la función de sensibilidad se obtienen justamente en la entrada o la salida del subsistema que está siendo analizado. Por otra parte, la tesis presenta un conjunto de parámetros internos asimilados a impedancias, junto con sus expresiones analíticas, que permiten una explicación detallada de las interacciones en el sistema. Dichas expresiones analíticas pueden obtenerse bien mediante las funciones de transferencia analíticas si se conoce la estructura interna, o utilizando medidas en frecuencia o identificación de las mismas a través de la respuesta temporal del convertidor. De acuerdo a las metodologías presentadas en esta tesis se puede predecir la estabilidad y el comportamiento de sistemas compuestos básicamente por convertidores CC-CC y filtros, cuya estructura interna es desconocida. La predicción se basa en un índice que condensa la información de los márgenes de estabilidad y que permite la obtención de un indicador de la estabilidad global de todo el sistema, permitiendo la comparación de la estabilidad de diferentes arquitecturas de sistemas de alimentación distribuidos. ABSTRACT The purpose of this thesis is to present dynamic small-signal stability and performance analysis methodology for dc-distributed systems consisting of commercial power modules. Furthermore, the objective is to introduce simple method to state the least conservative margins for robust stability as a single number. In addition, an index characterizing the overall system stability is obtained, based on which different dc-distributed systems can be compared in terms of robustness. The interconnected systems are prone to impedance-based interactions which might lead to transient-performance degradation or even instability. These systems typically are constructed using commercial converters with unknown internal structure. Therefore, the analysis presented throughout this thesis is based on frequency responses measurable from the input and output terminals. The stability margins are stated utilizing a concept of maximum peak criteria, derived from the behavior of impedance-based sensitivity function that provides a single number to state robust stability. Using this concept, the stability information at every system interface is combined to a meaningful number to state the average robustness of the system. In addition, theoretical formulas are extracted to assess source and load side interactions in order to describe detailed couplings within the system. The presented theoretical analysis methodologies are experimentally validated throughout the thesis. In this thesis, according to the presented analysis, the least conservative stability margins are provided as a single number guaranteeing robustness. It is also shown that within the interconnected system the robust stability is ensured only if the impedance-based minor-loop gain is determined at the very input or output of each subsystem. Moreover, a complete set of impedance-type internal parameters as well as the formulas according to which the interaction sensitivity can be fully explained and analyzed, is provided. The given formulation can be utilized equally either based on measured frequency responses, time-domain identified internal parameters or extracted analytic transfer functions. Based on the analysis methodologies presented in this thesis, the stability and performance of interconnected systems consisting of converters with unknown internal structure, can be predicted. Moreover, the provided concept to assess the least conservative stability margins enables to obtain an index to state the overall robust stability of distributed power architecture and thus to compare different systems in terms of stability.

Accurate Analysis of Subharmonic Oscillations of V^2 and V^2Ic Controls Applied to Buck Converter

V2Ic control provides very fast dynamic performance to the Buck converter both under load steps and under voltage reference steps. However, the design of this control is complex since it is prone to subharmonic oscillations and several parameters affect the stability of the system. This paper derives and validates a very accurate modeling and stability analysis of a closed-loop V2Ic control using the Floquet theory. This allows the derivation of sensitivity analysis to design a robust converter. The proposed methodology is validated on a 5-MHz Buck converter. The work is also extended to V2 control using the same methodology, showing high accuracy and robustness. The paper also demonstrates, on the V2 control, that even a low bandwidth-linear controller can affect the stability of a ripple-based control.