The Influence of Communication Range on Connectivity for Resilient Wireless Sensor Networks Using a Probabilistic Approach.

Wireless sensor networks (WSNs) consist of thousands of nodes that need to communicate with each other. However, it is possible that some nodes are isolated from other nodes due to limited communication range. This paper focuses on the influence of communication range on the probability that all nodes are connected under two conditions, respectively: (1) all nodes have the same communication range, and (2) communication range of each node is a random variable. In the former case, this work proves that, for 0menor queepsmenor quee^(-1) , if the probability of the network being connected is 0.36eps , by means of increasing communication range by constant C(eps) , the probability of network being connected is at least 1-eps. Explicit function C(eps) is given. It turns out that, once the network is connected, it also makes the WSNs resilient against nodes failure. In the latter case, this paper proposes that the network connection probability is modeled as Cox process. The change of network connection probability with respect to distribution parameters and resilience performance is presented. Finally, a method to decide the distribution parameters of node communication range in order to satisfy a given network connection probability is developed.

Low-cost CW-LFM radar sensor at 100 GHz

This paper presents a W-band high-resolution radar sensor for short-range applications. Low-cost technologies have been properly selected in order to implement a versatile and easily scalable radar system. A large operational bandwidth of 9 GHz, required for obtaining high-range resolution, is attained by means of a frequency multiplication-based architecture. The system characterization to identify the performance-limiting stages and the subsequent design optimization are presented. The assessment of system performance for several representative applications has been carried out.

Radio propagation modeling and measurements for ZigBee based indoor wireless sensor networks

The deployment of nodes in Wireless Sensor Networks (WSNs) arises as one of the biggest challenges of this field, which involves in distributing a large number of embedded systems to fulfill a specific application. The connectivity of WSNs is difficult to estimate due to the irregularity of the physical environment and affects the WSN designers? decision on deploying sensor nodes. Therefore, in this paper, a new method is proposed to enhance the efficiency and accuracy on ZigBee propagation simulation in indoor environments. The method consists of two steps: automatic 3D indoor reconstruction and 3D ray-tracing based radio simulation. The automatic 3D indoor reconstruction employs unattended image classification algorithm and image vectorization algorithm to build the environment database accurately, which also significantly reduces time and efforts spent on non-radio propagation issue. The 3D ray tracing is developed by using kd-tree space division algorithm and a modified polar sweep algorithm, which accelerates the searching of rays over the entire space. Signal propagation model is proposed for the ray tracing engine by considering both the materials of obstacles and the impact of positions along the ray path of radio. Three different WSN deployments are realized in the indoor environment of an office and the results are verified to be accurate. Experimental results also indicate that the proposed method is efficient in pre-simulation strategy and 3D ray searching scheme and is suitable for different indoor environments.

Packaging and testing of fiber Bragg gratings for use as strain sensor for rock specimens

This paper reports a packaging and calibration procedure for surface mounting of fiber Bragg grating (FBG) sensors to measure strain in rocks. The packaging of FBG sensors is performed with glass fiber and polyester resin, and then subjected to tensile loads in order to obtain strength and deformability parameters, necessaries to assess the mechanical performance of the sensor packaging. For a specific package, an optimal curing condition has been found, showing good repeatability and adaptability for non-planar surfaces, such as occurs in rock engineering. The successfully packaged sensors and electrical strain gages were attached to standard rock specimens of gabbro. Longitudinal and transversal strains under compression loads were measured with both techniques, showing that response of FBG sensors is linear and reliable. An analytical model is used to characterize the influences of rock substrate and FBG packaging in strain transmission. As a result, we obtained a sensor packaging for non-planar and complex natural material under acceptable sensitivity suitable for very small strains as occurs in hard rocks.

Application of noise analysis for sensor surveillance in Trillo NPP

It is a known fact that noise analysis is a suitable method for sensor performance surveillance. In particular, controlling the response time of a sensor is an efficient way to anticipate failures and to have the opportunity to prevent them. In this work the response times of several sensors of Trillo NPP are estimated by means of noise analysis. The procedure applied consists of modeling each sensor with autoregressive methods and getting the searched parameter by analyzing the response of the model when a ramp is simulated as the input signal. Core exit thermocouples and in core self-powered neutron detectors are the main sensors analyzed but other plant sensors are studied as well. Since several measurement campaigns have been carried out, it has been also possible to analyze the evolution of the estimated parameters during more than one fuel cycle. Some sensitivity studies for the sample frequency of the signals and its influence on the response time are also included. Calculations and analysis have been done in the frame of a collaboration agreement between Trillo NPP operator (CNAT) and the School of Mines of Madrid.

A low-mass impact sensor for high-speed firmness sensing of fruits.

A low-mass impact sensor for high-speed firmness sensing of fruits was built and tested. Results of tests with a rubber ball indicated that the impact measurement was not sensitive to the distance between the impactor and the impacting surface of the sample within the range of 8 to 23 mm, and was not sensitive to how the sample was held. Tests with kiwifruits and peaches show good correlation between firmness readings obtained with the impact sensor and those obtained with the penetrometer. The best correlation was between the slope of the impact curve (at mid-point) and the force-deformation firmness. Preliminary test showed that the sensor could sense fruit firmness at a speed of 5 fruits/s.