Determinación de la amplificación sísmica local en el Campus Sur UPM mediante la técnica de sismología de microtremores ReMi.

En el Campus Sur de la Universidad Politécnica de Madrid se ha llevado a cabo un proyecto para obtener una caracterización del subsuelo mediante ensayos ReMi, en colaboración con el departamento de Geofísica del Instituto Geográfico Nacional. La técnica ReMi (Refraction Microtremor) permite, mediante ensayos geofísicos realizados localmente sobre el terreno,obtener los parámetros físicos del mismo, que resultan de especial interés en el ámbito de la ingeniería civil. Esta técnica se caracteriza por englobarse dentro de la sísmica pasiva, muy empleada en prospección geofísica y basada en la obtención del modelo subyacente de distribución de velocidades de propagación de la onda S en función de la profundidad, con la ventaja de aprovechar el ruido sísmico ambiental como fuente de energía. Fue desarrollada en el Laboratorio Sismológico de Nevada (EEUU) por Louie (2001), con el objetivo de presentar una técnica innovadora en la obtención de las velocidades de propagación de manera experimental. Presenta ciertas ventajas, como la observación directa de la dispersión de ondas superficiales,que da un buen resultado de la velocidad de onda S, siendo un método no invasivo, de bajo coste y buena resolución, aplicable en entornos urbanos o sensibles en los que tanto otras técnicas sismológicas como otras variedades de prospección presentan dificultades. La velocidad de propagación de la onda S en los 30 primeros metros VS30, es ampliamente reconocida como un parámetro equivalente válido para caracterizar geotécnicamente el subsuelo y se halla matemáticamente relacionada con la velocidad de propagación de las ondas superficiales a observar mediante la técnica ReMi. Su observación permite el análisis espectral de los registros adquiridos, obteniéndose un modelo representado por la curva de dispersión de cada emplazamiento, de modo que mediante una inversión se obtiene el modelo de velocidad de propagación en función de la profundidad. A través de estos modelos, pueden obtenerse otros parámetros de interés sismológico. Estos resultados se representan sobre mapas isométricos para obtener una relación espacial de los mismos, particularmente conocido como zonación sísmica. De este análisis se extrae que la VS30 promedio del Campus no es baja en exceso, correspondiéndose a posteriori con los resultados de amplificación sísmica, período fundamental de resonancia del lugar y profundidad del sustrato rocoso. En última instancia se comprueba que los valores de amplificación sísmica máxima y el período al cual se produce posiblemente coincidan con los períodos fundamentales de resonancia de algunos edificios del Campus. ABSTRACT In South Campus at Polytechnic University of Madrid, a project has been carried out to obtain a proper subsoil description by applying ReMi tests, in collaboration with the Department of Geophysics of the National Geographic Institute. Through geophysical tests conducted locally, the ReMi (Refraction Microtremor) technique allows to establish the physical parameters of soil, which are of special interest in the field of civil engineering. This technique is part of passive seismic methods, often used in geophysical prospecting. It focuses in obtaining the underlying model of propagation velocity distribution of the shear wave according to depth and has the advantage of being able to use seismic ambient noise as a source of energy. It was developed in the Nevada Seismological Laboratory (USA) by Louie (2001) as an innovative technique for obtaining propagation velocities experimentally. It has several other advantages, including the direct observation of the dispersion of surface waves, which allows to reliably measure S wave velocity. This is a non-invasive, low cost and good resolution method, which can be applied in urban or sensitive environments where other prospection methods present difficulties. The propagation velocity of shear waves in the first 30 meters Vs30 is widely recognized as a valid equivalent parameter to geotechnically characterize the subsurface. It is mathematically related to surface wave's velocity of propagation, which are to observe using REMI technique. Spectral analysis of acquired data sets up a model represented by the dispersion curve at each site, so that, using an inversion process, propagation velocity model in relation to depth is obtained. Through this models, other seismologically interesting parameters can be obtained. These results are represented on isometric maps in order to obtain a spatial relationship between them, a process which is known as seismic zonation. This analysis infers that Vs30 at South Campus is not alarmingly low , corresponding with subsequent results of seismic amplification, fundamental period of resonance of soil and depth of bedrock. Ultimately, it's found that calculated values of soil's fundamental periods at which maximum seismic amplification occurs, may possibly match fundamental periods of some Campus buildings.

Nonlinear seismic behaviour of concrete arch bridges

Arch bridge structural solution has been known for centuries, in fact the simple nature of arch that require low tension and shear strength was an advantage as the simple materials like stone and brick were the only option back in ancient centuries. By the pass of time especially after industrial revolution, the new materials were adopted in construction of arch bridges to reach longer spans. Nowadays one long span arch bridge is made of steel, concrete or combination of these two as "CFST", as the result of using these high strength materials, very long spans can be achieved. The current record for longest arch belongs to Chaotianmen bridge over Yangtze river in China with 552 meters span made of steel and the longest reinforced concrete type is Wanxian bridge which also cross the Yangtze river through a 420 meters span. Today the designer is no longer limited by span length as long as arch bridge is the most applicable solution among other approaches, i.e. cable stayed and suspended bridges are more reasonable if very long span is desired. Like any super structure, the economical and architectural aspects in construction of a bridge is extremely important, in other words, as a narrower bridge has better appearance, it also require smaller volume of material which make the design more economical. Design of such bridge, beside the high strength materials, requires precise structural analysis approaches capable of integrating the combination of material behaviour and complex geometry of structure and various types of loads which may be applied to bridge during its service life. Depend on the design strategy, analysis may only evaluates the linear elastic behaviour of structure or consider the nonlinear properties as well. Although most of structures in the past were designed to act in their elastic range, the rapid increase in computational capacity allow us to consider different sources of nonlinearities in order to achieve a more realistic evaluations where the dynamic behaviour of bridge is important especially in seismic zones where large movements may occur or structure experience P - _ effect during the earthquake. The above mentioned type of analysis is computationally expensive and very time consuming. In recent years, several methods were proposed in order to resolve this problem. Discussion of recent developments on these methods and their application on long span concrete arch bridges is the main goal of this research. Accordingly available long span concrete arch bridges have been studied to gather the critical information about their geometrical aspects and properties of their materials. Based on concluded information, several concrete arch bridges were designed for further studies. The main span of these bridges range from 100 to 400 meters. The Structural analysis methods implemented in in this study are as following: Elastic Analysis: Direct Response History Analysis (DRHA): This method solves the direct equation of motion over time history of applied acceleration or imposed load in linear elastic range. Modal Response History Analysis (MRHA): Similar to DRHA, this method is also based on time history, but the equation of motion is simplified to single degree of freedom system and calculates the response of each mode independently. Performing this analysis require less time than DRHA. Modal Response Spectrum Analysis (MRSA): As it is obvious from its name, this method calculates the peak response of structure for each mode and combine them using modal combination rules based on the introduced spectra of ground motion. This method is expected to be fastest among Elastic analysis. Inelastic Analysis: Nonlinear Response History Analysis (NL-RHA): The most accurate strategy to address significant nonlinearities in structural dynamics is undoubtedly the nonlinear response history analysis which is similar to DRHA but extended to inelastic range by updating the stiffness matrix for every iteration. This onerous task, clearly increase the computational cost especially for unsymmetrical buildings that requires to be analyzed in a full 3D model for taking the torsional effects in to consideration. Modal Pushover Analysis (MPA): The Modal Pushover Analysis is basically the MRHA but extended to inelastic stage. After all, the MRHA cannot solve the system of dynamics because the resisting force fs(u; u_ ) is unknown for inelastic stage. The solution of MPA for this obstacle is using the previously recorded fs to evaluate system of dynamics. Extended Modal Pushover Analysis (EMPA): Expanded Modal pushover is a one of very recent proposed methods which evaluates response of structure under multi-directional excitation using the modal pushover analysis strategy. In one specific mode,the original pushover neglect the contribution of the directions different than characteristic one, this is reasonable in regular symmetric building but a structure with complex shape like long span arch bridges may go through strong modal coupling. This method intend to consider modal coupling while it take same time of computation as MPA. Coupled Nonlinear Static Pushover Analysis (CNSP): The EMPA includes the contribution of non-characteristic direction to the formal MPA procedure. However the static pushovers in EMPA are performed individually for every mode, accordingly the resulted values from different modes can be combined but this is only valid in elastic phase; as soon as any element in structure starts yielding the neutral axis of that section is no longer fixed for both response during the earthquake, meaning the longitudinal deflection unavoidably affect the transverse one or vice versa. To overcome this drawback, the CNSP suggests executing pushover analysis for governing modes of each direction at the same time. This strategy is estimated to be more accurate than MPA and EMPA, moreover the calculation time is reduced because only one pushover analysis is required. Regardless of the strategy, the accuracy of structural analysis is highly dependent on modelling and numerical integration approaches used in evaluation of each method. Therefore the widely used Finite Element Method is implemented in process of all analysis performed in this research. In order to address the study, chapter 2, starts with gathered information about constructed long span arch bridges, this chapter continuous with geometrical and material definition of new models. Chapter 3 provides the detailed information about structural analysis strategies; furthermore the step by step description of procedure of all methods is available in Appendix A. The document ends with the description of results and conclusion of chapter 4.

Criteria to determine seismic risk on sites. Application to Spanish dams

In this paper, the main steps necessary to evaluate the seismic risk on a site are discussed. Several examples from the authors practical experience are reported and a systematic procedure to study the seismic risk on a dam site is also shown. The characteristics of the available Spanish seismic information - mainly historical and non instrumental seismic records - are commented. Different types of seismic and geologic techniques to investigate the area under the dam are given. Finally, a probabilistic method to obtain from the given seismic intensities the design earthquake is summarized

Piezoelectric sensing and non-parametric statistical signal processing for health monitoring of hysteretic dampers used in seismic-resistant structures

The paper proposes a new application of non-parametric statistical processing of signals recorded from vibration tests for damage detection and evaluation on I-section steel segments. The steel segments investigated constitute the energy dissipating part of a new type of hysteretic damper that is used for passive control of buildings and civil engineering structures subjected to earthquake-type dynamic loadings. Two I-section steel segments with different levels of damage were instrumented with piezoceramic sensors and subjected to controlled white noise random vibrations. The signals recorded during the tests were processed using two non-parametric methods (the power spectral density method and the frequency response function method) that had never previously been applied to hysteretic dampers. The appropriateness of these methods for quantifying the level of damage on the I-shape steel segments is validated experimentally. Based on the results of the random vibrations, the paper proposes a new index that predicts the level of damage and the proximity of failure of the hysteretic damper