QKD in dense WDM passive optical networks

Quantum cryptography in communications networks

Multiplexing QKD systems in Conventional Optical Networks

Current QKD designs try to keep the quantum channel as error free as possible by using a separate physical medium for this purpose. In the most common case, this means the exclusive use of an optical fiber for the quantum channel, precluding its use for any other purpose. In current optical networks, the fiber is the single most expensive element and this poses a major problem from a cost and availability point of view. Sharing the fiber is thus mandatory for the widespread adoption of QKD. The objective of this communication is to propose a general scheme and present some preliminary measurements of a metropolitan area network (MAN) designed to multiplex of the order of 64 addressable quantum channels and the associated QKD classical service signals on a single dark fibre. It uses as much existing components and infraestructure as possible in an attempt to simultaneously lower most of the practical barriers for the adoption of QKD.

Deploying QKD in Standard Optical Networks

In order to deploy QKD in a cost effective and scalable way, its integration with already installed optical networks is a logical step. If, for the sake of security, we require that no intermediate trusted nodes would be needed, the maximum distance/absorptions allowed by QKD systems limit ourselves to metropolitan area networks. Current metro networks are mostly all optical and passive, hence a transparent link can be established among any two points and this link can be used to transport the quantum channel. In this poster we report on our findings studying the problems arising when integrating QKD systems in standard telecommunications networks.

Mach-Zehnder interferometer based on all-fiber multimode interference device for DPSK signal demodulation

Differential Phase Shift Keying (DPSK) modulation format has been shown as a robust solution for next-generation optical transmission systems. One key device enabling such systems is the delay interferometer, converting the signal phase information into intensity modulation to be detected by the photodiodes. Usually, Mach-Zehnder interferometer (MZI) is used for demodulating DPSK signals. In this paper, we developed an MZI which is based on all-fiber Multimode Interference (MI) structure: a multimode fiber (MMF) located between two single-mode fibers (SMF) without any transition zones. The standard MZI is not very stable since the two beams go through two different paths before they recombine. In our design the two arms of the MZI are in the same fiber, which will make it less temperature-sensitive than the standard MZI. Performance of such MZI will be analyzed from transmission spectrum. Finally such all-fiber MI-based MZI (MI-MZI) is used to demodulate 10 Gbps DPSK signals. The demodulated signals are analyzed from eye diagram and bit error rate (BER).

Infiltration of a photonic crystal fiber with cholesteric liquid crystal and blue phase

Photonic crystal fibers (PCF) have been selectively filled with a cholesteric liquid crystal (ChLC) with special interest in the blue phase (BP) of the liquid crystal. It has been observed thermal tuning of the guided light in the visible region. A dramatically enhance appears when the phase of the liquid crystal changes from cholesteric to blue phase I (BPI). When a thermal range of the blue phase I is achieved, no changes are observed while increasing temperature from BPI through BPII and to the isotropic phase.

Optimization and evaluation in space conditions of multi-GHz optical modulators

Among the different optical modulator technologies available such as polymer, III-V semiconductors, Silicon, the well-known Lithium Niobate (LN) offers the best trade-off in terms of performances, ease of use, and power handling capability [1-9]. The LN technology is still widely deployed within the current high data rate fibre optic communications networks. This technology is also the most mature and guarantees the reliability which is required for space applications [9].In or der to fulfil the target specifications of opto-microwave payloads, an optimization of the design of a Mach-Zehnder (MZ) modulator working at the 1500nm telecom wavelength was performed in the frame of the ESA-ARTES "Multi GigaHertz Optical Modulator" (MGOM) project in order to reach ultra-low optical insertion loss and low effective driving voltage in the Ka band. The selected modulator configuration was the X-cut crystal orientation, associated to high stability Titanium in-diffusion process for the optical waveguide. Starting from an initial modulator configuration exhibiting 9 V drive voltage @ 30 GHz, a complete redesign of the coplanar microwave electrodes was carried out in order to reach a 6 V drive voltage @ 30GHz version. This redesign was associated to an optimization of the interaction between the optical waveguide and the electrodes. Following the optimisation steps, an evaluation program was applied on a lot of 8 identical modulators. A full characterisation was carried out to compare performances, showing small variations between the initial and final functional characteristics. In parallel, two similar modulators were submitted to both gamma (10-100 krad) and proton irradiation (10.109 p/cm²) with minor performance degradation.

Planificación de una red 4G

La intensa evolución tecnológica que está experimentando nuestra sociedad en las últimas décadas hace que se estén desarrollando continuamente nuevas tecnologías que proporcionan mejoras tanto en la calidad como en la seguridad del servicio, este es el caso del 4G. A día de hoy, en España, la cuarta generación de comunicaciones móviles se ve encabezada por LTE, mientras que LTE-Advanced sólo se está implantando en las principales ciudades de nuestro país durante los últimos meses. Por este motivo, se ha creído interesante realizar una planificación sobre una zona que, hasta el momento, no está cubierta por cobertura LTE-Advanced. Además hay que tener en cuenta la naturaleza del terreno en el que trabajaremos, ya que se aleja del suelo urbano que encontramos en las principales ciudades con LTE-Advanced, como Madrid, Barcelona o Valencia. El estudio de esta zona semirural es de gran interés ya que uno de los objetivos de la cuarta generación es hacer llegar conexión a internet de calidad a lugares en los que no puede llegar la fibra óptica, como por ejemplo estas zonas semirurales. Para añadir aún más interés en el estudio, se ha decidido utilizar la banda de 800 MHz para el despliegue de la red. Esta banda que anteriormente era utilizada para la transmisión TDT, recientemente ha quedado liberada, en el conocido como Dividendo Digital para su uso en comunicaciones móviles. La tecnología LTE-Advanced se está empezando a desplegar en esta banda aunque realmente hasta Noviembre del año 2015 no tendremos un uso real de la misma, por lo que en estos momentos las redes 4G están utilizando la banda de 2.6 GHz. La utilización de la banda de 800 MHz conllevará mejoras tanto al usuario como a las operadoras, las cuales iremos viendo a lo largo del desarrollo del proyecto. La planificación pasará por distintas fases de optimización y expansión en las que se analizaran tanto la parte radioeléctrica como su capacidad. Se analizaran señales del tipo RSRP, RSSI o RSRQ y para el análisis de capacidad se definirá un conjunto de usuarios, distribuidos adecuadamente por toda la zona, que permitirá estudiar en detalle la capacidad de nuestra red. Para finalizar, se realizarán varias pruebas que demostrarán lo importante que es la tecnología MIMO tanto en LTE como en LTE-Advanced. ABSTRACT. Nowadays, our society is experiencing an intense pace of technological evolution which causes the constant development of new technologies. In the network planning area, these new technologies are focused on improving both quality and safety of service, with the recent deployment of 4G technologies in our networks. This project focuses on Spain, where the fourth generation of mobile communications is led by LTE, because LTE-Advanced has only been deployed in the largest cities, so far. The goal of this project is to plan, deploy and simulate LTE-Advanced network, of an area that hasn´t yet been covered. Furthermore, it will be taken into account the nature of the terrain where the network will be developed, as it moves away from urban areas in the major cities with LTE-Advanced, including Madrid, Barcelona and Valencia. The study of these semi-rural areas is extremely important because one of the main objectives of the fourth generation technologies is to get high-speed internet access to places that can be reached through other technologies, such as optical fiber. In order to adjust to the actual needs, the project was developed for the 800 MHz band. Those frequencies used to be assigned for digital terrestrial TV, but they have recently been released through the Digital Dividend in 2015 to use with mobile communications. That is the reason why, the LTE-Advanced technology in Spain is starting to be deployed in those frequencies. Despite the freeing of the 800 MHz band, it is not allowed to use it until November 2015, so 4G networks are currently using the 2.6 GHz band. The use of the 800 MHz band will led to advantages and improvements to users and operators, which will be detailed over the project. Each step of the planning of the 4G network is detailed. It is analyzed the optimization and expansion of the network, based on the radio and capacity premises. RSRP, RSSI or RSRQ signals were analyzed and an analysis of the network capacity was carried out. Finally, several tests are developed to show the importance of MIMO in LTE and LTE-Advanced.

Development and Testing of a Fiber Bragg Grating Strain Sensor for Uniaxial Compression of Rock Specimens

Los sensores de fibra óptica son una tecnología que ha madurado en los últimos años, sin embargo, se requiere un mayor desarrollo de aplicaciones para materiales naturales como las rocas, que por ser agregados complejos pueden contener partículas minerales y fracturas de tamaño mucho mayor que las galgas eléctricas usadas tradicionalmente para medir deformaciones en las pruebas de laboratorio, ocasionando que los resultados obtenidos puedan ser no representativos. En este trabajo fueron diseñados, fabricados y probados sensores de deformación de gran área y forma curvada, usando redes de Bragg en fibra óptica (FBG) con el objetivo de obtener registros representativos en rocas que contienen minerales y estructuras de diversas composiciones, tamaños y direcciones. Se presenta el proceso de elaboración del transductor, su caracterización mecánica, su calibración y su evaluación en pruebas de compresión uniaxial en muestras de roca. Para verificar la eficiencia en la transmisión de la deformación de la roca al sensor una vez pegado, también fue realizado el análisis de la transferencia incluyendo los efectos del adhesivo, de la muestra y del transductor. Los resultados experimentales indican que el sensor desarrollado permite registro y transferencia de la deformación fiables, avance necesario para uso en rocas y otros materiales heterogénos, señalando una interesante perspectiva para aplicaciones sobre superficies irregulares, pues permite aumentar a voluntad el tamaño y forma del área de registro, posibilita también obtener mayor fiabilidad de resultados en muestras de pequeño tamaño y sugiere su conveniencia en obras, en las cuales los sistemas eléctricos tradicionales tienen limitaciones. ABSTRACT Optical fiber sensors are a technology that has matured in recent years, however, further development for rock applications is needed. Rocks contain mineral particles and features larger than electrical strain gauges traditionally used in laboratory tests, causing the results to be unrepresentative. In this work were designed, manufactured, and tested large area and curved shape strain gages, using fiber Bragg gratings in optical fiber (FBG) in order to obtain representative measurement on surface rocks samples containing minerals and structures of different compositions, sizes and directions. This reports presents the processes of manufacturing, mechanical characterization, calibration and evaluation under uniaxial compression tests on rock samples. To verify the efficiency of rock deformation transmitted to attached sensor, it was also performed the analysis of the strain transfer including the effects of the bonding, the sample and the transducer. The experimental results indicate that the developed sensor enables reliable measurements of the strain and its transmission from rock to sensor, appropriate for use in heterogeneous materials, pointing an interesting perspective for applications on irregular surfaces, allowing increasing at will the size and shape of the measurement area. This research suggests suitability of the optical strain gauge for real scale, where traditional electrical systems have demonstrated some limitations.

Optical sensing of the fatigue damage state of CFRP under realistic aeronautical load sequences

We present an optical sensing methodology to estimate the fatigue damage state of structures made of carbon fiber reinforced polymer (CFRP), by measuring variations on the surface roughness. Variable amplitude loads (VAL), which represent realistic loads during aeronautical missions of fighter aircraft (FALSTAFF) have been applied to coupons until failure. Stiffness degradation and surface roughness variations have been measured during the life of the coupons obtaining a Pearson correlation of 0.75 between both variables. The data were compared with a previous study for Constant Amplitude Load (CAL) obtaining similar results. Conclusions suggest that the surface roughness measured in strategic zones is a useful technique for structural health monitoring of CFRP structures, and that it is independent of the type of load applied. Surface roughness can be measured in the field by optical techniques such as speckle, confocal perfilometers and interferometry, among others.