Proposal of a dynamic performance index to analyze driving pattern effect on car emissions

The contributions of driver behaviour as well as surrounding infrastructure are decisive on pollutant emissions from vehicles in real traffic situations. This article deals with the preliminary study of the interaction between the dynamic variables recorded in a vehicle (driving pattern) and pollutant emissions produced over a given urban route. It has been established a “dynamic performance index”-DPI, which is calculated from some driving pattern parameters, which in turn depends on traffic congestion level and route characteristics, in order to determine whether the driving has been aggressive, normal or calm. Two passenger cars instrumented with a portable activity measurement system -to record dynamic variables- and on-board emission measurement equipment have been used. This study has shown that smooth driving patterns can reduce up to 80% NOX emissions and up to 20% of fuel in the same route

Environmental assessment of low speed policies for motor vehicle mobility in city centres

streets in local residential areas in large cities, real traffic tests for pollutant emissions and fuel consumption have been carried out in Madrid city centre. Emission concentration and car activity were simultaneously measured by a Portable Emissions Measurement System. Real life tests carried out at different times and on different days were performed with a turbo-diesel engine light vehicle equipped with an oxidizer catalyst and using different driving styles with a previously trained driver. The results show that by reducing the speed limit from 50 km h-1 to 30 km h-1, using a normal driving style, the time taken for a given trip does not increase, but fuel consumption and NOx, CO and PM emissions are clearly reduced. Therefore, the main conclusion of this work is that reducing the speed limit in some narrow streets in residential and commercial areas or in a city not only increases pedestrian safety, but also contributes to reducing the environmental impact of motor vehicles and reducing fuel consumption. In addition, there is also a reduction in the greenhouse gas emissions resulting from the combustion of the fuel.

Aspectos de la medición dinámica instantánea de emisiones de motores. Aplicación al desarrollo de un equipo portátil y una metodología para estudios de contaminación de vehículos en tráfico real.

Esta Tesis Doctoral se encuadra en el ámbito de la medida de emisiones contaminantes y de consumo de combustible en motores de combustión interna alternativos cuando se utilizan como plantas de potencia para propulsión de vehículos ligeros de carretera, y más concretamente en las medidas dinámicas con el vehículo circulando en tráfico real. En este ámbito, el objetivo principal de la Tesis es estudiar los problemas asociados a la medición en tiempo real con equipos embarcados de variables medioambientales, energéticas y de actividad, de vehículos ligeros propulsados por motores térmicos en tráfico real. Y como consecuencia, desarrollar un equipo y una metodología apropiada para este objetivo, con el fin de realizar consiguientemente un estudio sobre los diferentes factores que influyen sobre las emisiones y el consumo de combustible de vehículos turismo en tráfico real. La Tesis se comienza realizando un estudio prospectivo sobre los trabajos de otros autores relativos al desarrollo de equipos portátiles de medida de emisiones (Portable Emission Measurement Systems – PEMS), problemas asociados a la medición dinámica de emisiones y estudios de aplicación en tráfico real utilizando este tipo de equipos. Como resultado de este estudio se plantea la necesidad de disponer de un equipo específicamente diseñado para ser embarcado en un vehículo que sea capaz de medir en tiempo real las concentraciones de emisiones y el caudal de gases de escape, al mismo tiempo que se registran variables del motor, del vehículo y del entorno como son la pendiente y los datos meteorológicos. De esta forma se establecen las especificaciones y condiciones de diseño del equipo PEMS. Aunque al inicio de esta Tesis ya existían en el mercado algunos sistemas portátiles de medida de emisiones (PEMS: Portable Emissions Measurement Systems), en esta Tesis se investiga, diseña y construye un nuevo sistema propio, denominado MIVECO – PEMS. Se exponen, discuten y justifican todas las soluciones técnicas incorporadas en el sistema que incluyen los subsistema de análisis de gases, subsistemas de toma de muestra incluyendo caudalímetro de gases de escape, el subsistema de medida de variables del entorno y actividad del vehículo y el conjunto de sistemas auxiliares. El diseño final responde a las hipótesis y necesidades planteadas y se valida en uso real, en banco de rodillos y en comparación con otro equipos de medida de emisiones estacionarios y portátiles. En esta Tesis se presenta también toda la investigación que ha conducido a establecer la metodología de tratamiento de las señales registradas en tiempo real que incluye la sincronización, cálculos y propagación de errores. La metodología de selección y caracterización de los recorridos y circuitos y de las pautas de conducción, preparación del vehículo y calibración de los equipos forma también parte del legado de esta Tesis. Para demostrar la capacidad de medida del equipo y el tipo de resultados que pueden obtenerse y que son útiles para la comunidad científica, y las autoridades medioambientales en la parte final de esta Tesis se plantean y se presentan los resultados de varios estudios de variables endógenas y exógenas que afectan a las emisiones instantáneas y a los factores de emisión y consumo (g/km) como: el estilo de conducción, la infraestructura vial, el nivel de congestión del tráfico, tráfico urbano o extraurbano, el contenido de biocarburante, tipo de motor (diesel y encendido provocado), etc. Las principales conclusiones de esta Tesis son que es posible medir emisiones másicas y consumo de motores de vehículos en uso real y que los resultados permiten establecer políticas de reducción de impacto medio ambiental y de eficiencia energética, pero, se deben establecer unas metodologías precisas y se debe tener mucho cuidado en todo el proceso de calibración, medida y postratamientos de los datos. Abstract This doctoral thesis is in the field of emissions and fuel consumption measurement of reciprocating internal combustion engines when are used as power-trains for light-duty road vehicles, and especially in the real-time dynamic measurements procedures when the vehicle is being driven in real traffic. In this context, the main objective of this thesis is to study the problems associated with on-board real-time measuring systems of environmental, energy and activity variables of light vehicles powered by internal combustion engines in real traffic, and as a result, to develop an instrument and an appropriate methodology for this purpose, and consequently to make a study of the different factors which influence the emissions and the fuel consumption of passenger cars in real traffic. The thesis begins developing a prospective study on other authors’ works about development of Portable Emission Measurement Systems (PEMS), problems associated with dynamic emission measurements and application studies on actual traffic using PEMS. As a result of this study, it was shown that a measuring system specifically designed for being on-board on a vehicle, which can measure in real time emission concentrations and exhaust flow, and at the same time to record motor vehicle and environment variables as the slope and atmospheric data, is needed; and the specifications and design parameters of the equipment are proposed. Although at the beginning of this research work there were already on the market some PEMS, in this Thesis a new system is researched, designed and built, called MIVECO – PEMS, in order to meet such measurements needs. Following that, there are presented, discussed and justify all technical solutions incorporated in the system, including the gas analysis subsystem, sampling and exhaust gas flowmeter subsystem, the subsystem for measurement of environment variables and of the vehicle activity and the set of auxiliary subsystems. The final design meets the needs and hypotheses proposed, and is validated in real-life use and chassis dynamometer testing and is also compared with other stationary and on-board systems. This thesis also presents all the research that has led to the methodology of processing the set of signals recorded in real time including signal timing, calculations and error propagation. The methodology to select and characterize of the routes and circuits, the driving patterns, and the vehicle preparation and calibration of the instruments and sensors are part of the legacy of this thesis. To demonstrate the measurement capabilities of the system and the type of results that can be obtained and that are useful for the scientific community and the environmental authorities, at the end of this Thesis is presented the results of several studies of endogenous and exogenous variables that affect the instantaneous and averaged emissions and consumption factors (g/km), as: driving style, road infrastructure, the level of traffic congestion, urban and extra-urban traffic, biofuels content, type of engine (diesel or spark ignition) etc. The main conclusions of this thesis are that it is possible to measure mass emissions and consumption of vehicle engines in actual use and that the results allow us to establish policies to reduce environmental impact and improve energy efficiency, but, to establish precise methodologies and to be very careful in the entire process of calibration, measurement and data post-treatment is necessary.

Optimización de la metodología de contratación de carbones térmicos con destino a la generación eléctrica

En los últimos quince años se ha producido una liberalización de los mercados eléctricos en los distintos países de ámbito occidental que ha ido acompañado de un incremento por la preocupación por la incidencia de las distintas tecnologías de generación en el entorno medioambiental. Ello se ha traducido en la aparición de un marco regulatorio más restrictivo sobre las tecnologías de generación fósiles, con mayor incidencia en las derivadas de productos petrolíferos y carbón. A nivel mundial han ido apareciendo cambios normativos relativos a las emisiones de distintos elementos contaminantes (CO2, SO2, NOx…), que hacen que en particular las centrales térmicas de carbón vean muy afectadas su rentabilidad y funcionamiento. Esta situación ha supuesto que la tecnología de generación eléctrica con carbón haya avanzado considerablemente en los últimos años (calderas supercríticas, sistemas de desulfuración, gasificación del carbón…). No obstante, el desarrollo de la generación con energías renovables, la generación con gas mediante centrales de ciclo combinado y la opinión social relativa a la generación con carbón, principalmente en Europa, suponen un serio obstáculo a la generación con carbón. Por consiguiente, se hace necesario buscar vías para optimizar la competitividad de las centrales de carbón y el camino más razonable es mejorar el margen esperado de estas plantas y en particular el coste de adquisición del carbón. Ello se hace aún más importante por el hecho de existir numerosas centrales de carbón y un elevado número de nuevos proyectos constructivos de centrales de carbón en países asiáticos. Por consiguiente, el objeto de la presente tesis doctoral se centra en definir una metodología para optimizar la compra de carbón, desde el punto de vista económico y técnico, con destino a su consumo en una central térmica, con ello reducir el coste del carbón consumido y mejorar su competitividad. También se enfoca a determinar que herramientas pueden ser utilizadas para optimizar la gestión del carbón después de su compra y con ello abrir la posibilidad de obtener márgenes adicionales para dicho carbón. De acuerdo con este objetivo, el autor de la presente Tesis Doctoral realiza tres aportaciones novedosas en el ámbito de la contratación de carbón térmico y su optimización posterior: - Evaluación de carbones para su adquisición considerando el efecto de la calidad del carbón en el coste de generación asociado a cada carbón ofertado. - Creación, desarrollo, implantación y utilización de una potente herramienta de planificación de Combustibles. Esta herramienta, está diseñada con el objeto de determinar la solución económica óptima de aprovisionamientos, consumos y niveles de existencias para un parque de generación con centrales de carbón y fuelóleo. - La extensión de una metodología contractual habitual en el mercado spot de Gas Natural Licuado, a la contratación spot de Carbón de Importación. Esta se basa en el desarrollo de Acuerdos Marcos de Compra/Venta de carbón, que por su flexibilidad permitan obtener resultados económicos adicionales después de la compra de un carbón. Abstract In the last fifteen years, a liberalization of the electrical markets has occurred in the western countries. This process has been accompanied by an increasing concern of the impact of the different generation technologies towards the environment. This has motivated a regulated framework restricting the use of fossil fuels, impacting a great deal in coal and oil based products. Worldwide, new legal changes have been arising related to the emissions of the different pollutants (CO2, SO2, NOx…). These changes have had a deep impact in the feasibility, profit and running of coal fired power plants. This situation has motivated the coal electrical generation technologies to move forward in an important way in the last few years (supercritical furnaces, desulphuration plants, coal gasification…). Nevertheless, the development of the renewable generation, the gas combined cycle generation and the social opinion related to the coal electrical generation, mainly in Europe, have created a serious obstacle to the generation of electricity by coal. Therefore it is necessary to look for new paths in order to optimize the competitiveness of the coal fired power plants and the most reasonable way is to improve the expected margin of these plants and particularly the coal purchase cost. All of the above needs to be taken into context with the large number of existing coal fired power plants and an important number of new projects in Asian countries. Therefore, the goal of the current doctoral dissertation is focused to define a methodology to be considered in order to optimize the coal purchase, from an economical and a technical point of view. This coal, destined for power plant consumption, permits the reduction of consumption coal cost and improves the plant’s competitiveness. This document is also focused to define what tools we can use to optimize the coal management after deal closing and therefore open the possibility to get further margins. According to this goal, the author of this doctoral dissertation provides three important new ideas in the ambit of contracting steam coal and the posterior optimization: - Evaluation of coal purchases, considering the effect of coal quality on the cost of generation associated with each type of coal offered. - The creation, development, deployment and use of a strong planning tool of fuels. This tool is designed for the purpose of determining the optimal economic solution of fuel supply, consumption and stock levels for a power generation portfolio using coal and fuel oil fired power plants. - The application of a common contractual methodology in the spot market of Liquid Natural Gas, for the contracting spot imported coal. This is based on the development of Framework Agreements for the Purchasing / Sale of coal, which because of its flexibility allows for the gain of additional financial results after the purchase of coal.

Quantity of CO2 Emissions in the Life Cycle of a Highway Infrastructure

There is strong evidence to indicate that carbon dioxide and other greenhouse gases are accumulating at unprecedented concentrations in out atmosphere contributing to global climate change. Evidence is equally strong that human activities, mainly the burning of fossil fuels, are driving force in this process (IPCC 2007). While different industries contribute varying amounts to total anthropogenic greenhouse gases, it is incumbent upon each to understand its contribution and search for sensible ways to reduce overall greenhouse gas production. The aim of this paper is the development of a methodology to determine the amount of CO2 emissions of a highway, allowing providing solutions that can improve the energy footprint and reduce its emissions

Assessment of self-combustion risks for solid fuels (POSTER)

Every solid fuel has a tendency to react with oxygen, a fact that constitutes the basis of their ability to oxidation and energy intake for combustion, but that poses a risk when it occurs in an uncontrolled manner. When the slow oxidation phenomenon produces more heat than can be evacuated, the result is a heating process, which promotes combustion reactions, primarily fuel oxidation, and a progressive increase in temperature.

Contribution sharing of a fuel mixture components to the fuel cell potencial of a direct alcohol fuel cell

The increasing worldwide demand for electricity impels to develop clean and renewable energy resources. In the field of portable power devices not only size and weight represent important aspects to take into account, but the fuel and its storage are also critical issues to consider. In this last sense, the direct methanol (MeOH) fuel cells (DMFC) play an important role as they can offer high power and energy density, low emissions, ambient operating conditions and fast and convenient refuelling.

Kinetics of CO2 absorption into aqueous solutions in CO2

This research has been performed to emphasize about the problem known as ?climate changes? occurring due to the greenhouse gases emissions (Carbon dioxide (CO2), Methane (CH4),Nitrogen oxides (NOx), Ozone (O3), Chlorofluorocarbons (artificial). Specially, the project will be focused on the CO2 emissions produced mainly from the fossil fuels burning in power plants and other kind of industrial processes. To understand how important the global is warming and therefore the climate change, both the increase of emissions and the evolution of those will be studied in this project drawing conclusions about its effect. The Kyoto Protocol, the most important agreement internationally, signed by a great majority of the industrialized and developed countries, which try to limit the CO2 emissions to the atmosphere, will be cited in this project. Taking into account the effects of global warming and applying the international legislation on emissions of greenhouse gases, a number of measures will be exposed, where the CO2 capture will be studied deeply. Three different kind of CO2 capture technologies will be studied, drawing the conclusion that the post-combustion capture, in particular by amine chemical absorption, is the most efficient one.

Biokerosene from coconut, babassu, camelina and palm kernel oils: production and properties of their blends with fossil kerosene

On December 20th 2006 the European Commission approved a law proposal to include the civil aviation sector in the European market of carbon dioxide emission rights [European Union Emissions Trading System, EUETS). On July 8th 2009, the European Parliament and Conseil agreed that all flights leaving or landing in the EU airports starting from January 1st 2012 should be included in the EUETS. On November 19th 2008, the EU Directive 2008/101/CE [1] included the civil aviation activities in the EUETS, and this directive was transposed by the Spanish law 13/2010 of July 5th 2010 [2]. Thus, in 2012 the aviation sector should reduce their emissions to 97 % of the mean values registered in the period 2004-2006, and for 2013 these emission reductions should reach 95 % of the mean values for that same period. Trying to face this situation, the aviation companies are planning seriously the use of alternative jet fuels to reduce their greenhouse gas emissions and to lower their costs. However, some US airlines have issued a lawsuit before the European Court of Justice based in that this EU action violates a long standing worldwide aviation treaty, the Chicago convention of 1944, and also the Chinese aviation companies have rejected to pay any EU carbon dioxide tax [3]. Moreover, the USA Departments of Agriculture and Energy and the Navy will invest a total of up to $150 million over three years to spur production of aviation and marine biofuels for commercial and military applications [4]. However, the jet fuels should fulfill a set of extraordinarily sensitive properties to guarantee the safety of planes and passengers during all the flights.

Energy consumption and carbon dioxide emissions in rail and road freight transport in Spain: a case study of car carriers and bulk petrochemicals

This article provides a new methodology for estimating fuel consumption and emissions by enabling a correct comparison between freight transportation modes. The approach is developed and integrated as a part of an intelligent transportation system dealing with goods movement. A key issue is related to energy consumption ratios and consequent CO2 emissions. Energy consumption ratios are often used based on transport demand. However, including other ratios based on transport supply can be useful. Furthermore, it is important to indicate which factors are associated with variations in energy consumption and emissions; especially of interest are parameters that have a higher incidence and order of magnitude, in order to fairly compare and understand the difference between transport modes and sub-modes. The study finds that the use of an energy consumption equation can improve the quality of the estimates. The study proposes that coefficients that define the energy consumption equation should be tested to determine market niches and sources of improvement in energy consumption according to the category of vehicles, fuel types used, and classes of products transported.

Co2 capture in power plants-using the oxy-combustion principle

In the C02 capture from power generation, the energy penalties for the capture are one of the main challenges. Nowadays, the post-combustion methods have energy penalties 10wer than the oxy combustion and pre-combustion technologies. One of the main disadvantages of the post combustion method is the fact that the capture ofC02at atmospheric pressure requires quite big equipment for the high flow rates of flue gas, and the 10w partial pressure of the CO2generates an important 10ss of energy. The A1lam cyc1e presented for NETPOWER gives high efficiencies in the power production and 10w energy penalties. A simulation of this cyc1e is made together with a simulation of power plants with pre-combustion and post-combustion capture and without capture for natural gas and forcoa1. The simulations give 10wer efficiencies than the proposed for NETPOWER For natural gas the efficiency is 52% instead of the 59% presented, and 33% instead of51% in the case of using coal as fuel. Are brought to light problems in the CO2compressor due the high flow ofC02that is compressed unti1300 bar to be recyc1ed into the combustor.

On the formation of nitrogen oxides in the combustion processes of hydrogen in air

A research programme is being carried out at the Institute Nacional de Tecnica Aeroespacial of Spain, on several aspects of the formation of nitrogen oxides in continuous flow combustion systems, considering hydrogen and hydrocarbons as fuels. The research programme is fundamentally oriented on the basic aspects of the problem, although it also includes the study of the influence on the formation process of several operational and design variables of the combusters, such as type of fuels, fuel/air ratio, degree of mixing in premixed type flames, existence of droplets as compared with homogeneous combustion.This problem of nitrogen oxides formation is receiving lately great attention, specially in connection with automobile reciprocating engines and aircraft gas turbines. This is due to the fact of the increasing frequency and intensity of photochemical hazes or smog, typical of urban areas submitted to strong solar radiation, which are originated by the action on organic compounds of the oxidants resulting from the photochemical decomposition of nitrogen dioxide N02. In the combustion process almost all nitrogen oxides are in form of NO. This nitric oxide reacts with the oxygen of the air and forms N02, this reaction only taking place in or near the exhaust of tne motors, since the N0-02 reaction becomes frozen for the concentration existing in the atmosphere.

Estudio microestructural y de los procesos de hidratación de cementos con adiciones

En los últimos años, las sociedades industrializadas han tomado una mayor conciencia sobre el problema que suponen las emisiones indiscriminadas de gases de efecto invernadero a la atmósfera. El hormigón, cuyo principal componente es el cemento, es probablemente el material más utilizado en construcción. En la actualidad, las emisiones globales de CO2 debidas a la combustión del CaCO3 del cemento Pórtland representan entre el 5% y el 10% respecto del total. Estos valores son de gran interés si se considera que el compromiso aceptado al firmar el Protocolo de Kioto es de una reducción del 5% antes del año 2020, sobre el total de gases producidos. El principal objetivo del presente trabajo es el estudio microestructural y de los procesos de hidratación de los cementos con adiciones. Para ello se propone contribuir a la investigación sobre nuevos productos cementicios basados en micropartículas esféricas vítreas que pueden adicionarse al cemento antes del proceso de amasado. Los resultados obtenidos se han contrastado con las adiciones convencionales de más uso en la actualidad. El nuevo material basa su composición en la química del aluminio y el silicio. Al disminuir la cantidad de CaCO3, se contribuye al desarrollo sostenible y a la reducción de emisiones de CO2. La patente creada por el Grupo Cementos Pórtland Valderrivas (GCPV), describe el proceso de producción de las cemesferas (WO 2009/007470, 2010). Los productos que forman la materia prima para la elaboración de las cemesferas son arcillas, calizas, margas o productos o subproductos industriales, que tras su molienda, son fundidos mediante un fluido gaseoso a elevada temperatura (entre 1250ºC y 1600ºC). Este proceso permite obtener un producto final en forma esférica maciza o microesfera, que tras estabilizarse mediante un enfriamiento rápido, consigue una alta vitrificación idónea para su reactividad química, con una mínima superficie específica en relación a su masa. El producto final obtenido presenta prácticamente la finura requerida y no precisa ser molido, lo que reduce las emisiones de CO2 por el ahorro de combustible durante el proceso de molienda. El proceso descrito permite obtener un amplio abanico de materiales cementantes que, no solo pueden dar respuesta a los problemas generados por las emisiones de CO2, sino también a la disponibilidad de materiales en países donde hasta el momento no se puede fabricar cemento debido a la falta de calizas. Complementariamente se ha optimizado el método de cálculo del grado de hidratación a partir de los resultados del ensayo de ATD-TG en base a los modelos de cálculo de Bhatty y Pane. El método propuesto permite interpretar el comportamiento futuro del material a partir de la interpolación numérica de la cantidad de agua químicamente enlazada. La evolución del grado de hidratación tiene una relación directa con el desarrollo de la resistencia mecánica del material. Con el fin de caracterizar los materiales de base cemento, se ha llevado a cabo una amplia campaña experimental en pasta de cemento, mortero y hormigón. La investigación abarca tres niveles: caracterización microestructural, macroestructural y caracterización del comportamiento a largo plazo, fundamentalmente durabilidad. En total se han evaluado ocho adiciones diferentes: cuatro adiciones convencionales y cuatro tipos de cemesferas con diferente composición química. Los ensayos a escala microscópica comprenden la caracterización química, granulométrica y de la superficie específica BET de los materiales anhidros, análisis térmico diferencial y termogravimétrico en pasta de cemento y mortero, resonancia magnética de silicio en pasta de cemento, difracción de rayos X de los materiales anhidros y de las probetas de pasta, microscopía electrónica de barrido con analizador de energía dispersiva por rayos X en pasta y mortero, y porosimetría por intrusión de mercurio en mortero. La caracterización macroscópica del material comprende ensayos de determinación del agua de consistencia normal y de los tiempos de inicio y fin de fraguado en pasta de cemento, ensayos de resistencia mecánica a flexión y compresión en probetas prismáticas de mortero, y ensayos de resistencia a compresión en probetas de hormigón. Para caracterizar la durabilidad se han desarrollado ensayos de determinación del coeficiente de migración de cloruros y ensayos de resistividad eléctrica en probetas de mortero. Todos los ensayos enumerados permiten clarificar el comportamiento de las cemesferas y compararlo con las distintas adiciones de uso convencional. Los resultados reflejan un buen comportamiento resistente y durable de los materiales con adición de cemesferas. La caracterización microscópica refleja su relación con las propiedades mesoscópicas y permite comprender mejor la evolución en los procesos de hidratación de las cemesferas. In recent years industrialised societies have become increasingly aware of the problem posed by indiscriminate emission of greenhouse gases into the atmosphere. Concrete, with a main component being cement, is arguably the most widely used construction material. At present, global emissions of CO2 due to the combustion of CaCO3 from Portland cement represent between 5% and 10% of the total. If the requirement of the Kyoto Protocol of a reduction of 5% of the total gas produced before 2020 is considered, then such values are of significant interest. The main objective of this work is the assessment of the microstructure and the hydration processes of cements with additions. Such an examination proposes research into new cementitious products based on vitreous spherical microparticles that may be added to the cement before the mixing process. The results are compared with the most commonly used conventional additions. The new material bases its composition on the chemistry of aluminium and silicates. By decreasing the amount of CaCO3, it is possible both to contribute to sustainable development and reduce CO2 emissions. The patent created by Grupo Cementos Portland Valderrivas (GCPV) describes the production process of microspheres (WO 2009/007470, 2010). The products that form the raw material for manufacture are clays, lime-stone, marl and industrial products or by-products that melt after being ground and fed into a gaseous fluid at high temperatures (1250°C and 1600°C). This process allows the obtaining of a product with a solid-spherical or micro-spherical shape and which, after being stabilised in a solid state by rapid cooling, obtains a high vitrification suitable for chemical reactivity, having a minimal surface in relation to its mass. Given that the final product has the fineness required, it prevents grinding that reduces CO2 emissions by saving fuel during this process. The process, which allows a wide range of cementitious materials to be obtained, not only addresses the problems caused by CO2 emissions but also enhances the availability of materials in countries that until the time of writing have not produced cement due to a lack of limestone. In addition, the calculation of the degree of hydration from the test results of DTA-TG is optimised and based on Bhatty and Pane calculation models. The proposed method allows prediction of the performance of the material from numerical interpolation of the amount of chemically bound water. The degree of hydration has a direct relationship with the development of material mechanical strength. In order to characterise the cement-based materials, an extensive experimental campaign in cement paste, concrete and mortar is conducted. The research comprises three levels: micro-structural characterisation, macro-structural and long-term behaviour (mainly durability). In total, eight additions are assessed: four conventional additions and four types of microspheres with different chemical compositions. The micro-scale tests include characterisation of chemical composition, particle size distribution and the BET specific surface area of anhydrous material, differential thermal and thermogravimetric analysis in cement paste and mortar, silicon-29 nuclear magnetic resonance in cement paste, X-ray diffraction of the anhydrous materials and paste specimens, scanning of electron microscopy with energy dispersive X-ray analyser in cement paste and mortar, and mercury intrusion porosimetry in mortar. The macroscopic material characterisation entails determination of water demand for normal consistency, and initial and final setting times of cement paste, flexural and compressive mechanical strength tests in prismatic mortar specimens, and compressive strength tests in concrete specimens. Tests for determining the chloride migration coefficient are performed to characterise durability, together with electrical resistivity tests in mortar specimens. All the tests listed allow clarification of the behaviour of the microspheres and comparison with the various additions of conventional use. The results show good resistance and durable behaviour of materials with a microsphere addition. Microscopic characterisation reflects their relationship with mesoscopic properties and provides insights into the hydration processes of the microspheres.

The impact of the economic crisis and policy actions on GHG emissions from road transport in Spain

Road traffic is the greatest contributor to the carbon footprint of the transport sector and reducing it has become one of the main targets of sustainable transport policies. An analysis of the main factors influencing greenhouse gas (GHG) emissions is essential for designing new energy- and environmentally efficient strategies for the road transport. This paper addresses this need by (i) identifying factors which influence the carbon footprint, including traffic activity, fuel economy and socioeconomic development; and (ii) proposing a methodological framework which uses Modified Laspeyres Index decomposition to analyze the effect of important drivers on the changes in emissions of road transport in Spain during the period from 1990 to 2010. The results demonstrate that the country׳s economic growth has been closely linked to the rise in GHG emissions. The innovative contribution of this paper is the special analysis of the changes in mobility patterns and GHG emissions during the economic crisis, when, for the first time, Spanish road traffic emissions decreased. The reduction of road transport and improved energy efficiency has been powerful contributors to this decrease, demonstrating the effectiveness of energy-saving measures. On the basis of this analysis, several tailored policy recommendations have been suggested for future implementation.

Flammability conditions for ultra-lean hydrogen premixed combustion based on flame-ball analyses

It has been reasoned that the structures of strongly cellular flames in very lean mixtures approach an array of flame balls, each burning as if it were isolated, thereby indicating a connection between the critical conditions required for existence of steady flame balls and those necessary for occurrence of self-sustained premixed combustion. This is the starting assumption of the present study, in which structures of near-limit steady sphericosym-metrical flame balls are investigated with the objective of providing analytic expressions for critical combustion conditions in ultra-lean hydrogen-oxygen mixtures diluted with N2 and water vapor. If attention were restricted to planar premixed flames, then the lean-limit mole fraction of H2 would be found to be roughly ten percent, more than twice the observed flammability limits, thereby emphasizing the relevance of the flame-ball phenomena. Numerical integrations using detailed models for chemistry and radiation show that a onestep chemical-kinetic reduced mechanism based on steady-state assumptions for all chemical intermediates, together with a simple, optically thin approximation for water-vapor radiation, can be used to compute near-limit fuel-lean flame balls with excellent accuracy. The previously developed one-step reaction rate includes a crossover temperature that determines in the first approximation a chemical-kinetic lean limit below which combustión cannot occur, with critical conditions achieved when the diffusion-controlled radiation-free peak temperature, computed with account taken of hydrogen Soret diffusion, is equal to the crossover temperature. First-order corrections are found by activation-energy asymptotics in a solution that involves a near-field radiation-free zone surrounding a spherical flame sheet, together with a far-field radiation-conduction balance for the temperature profile. Different scalings are found depending on whether or not the surrounding atmosphere contains wáter vapor, leading to different analytic expressions for the critical conditions for flame-ball existence, which give results in very good agreement with those obtained by detailed numerical computations.