Active Optical Sensors for Tree Stem Detection and Classification in Nurseries.

Active optical sensing (LIDAR and light curtain transmission) devices mounted on a mobile platform can correctly detect, localize, and classify trees. To conduct an evaluation and comparison of the different sensors, an optical encoder wheel was used for vehicle odometry and provided a measurement of the linear displacement of the prototype vehicle along a row of tree seedlings as a reference for each recorded sensor measurement. The field trials were conducted in a juvenile tree nursery with one-year-old grafted almond trees at Sierra Gold Nurseries, Yuba City, CA, United States. Through these tests and subsequent data processing, each sensor was individually evaluated to characterize their reliability, as well as their advantages and disadvantages for the proposed task. Test results indicated that 95.7% and 99.48% of the trees were successfully detected with the LIDAR and light curtain sensors, respectively. LIDAR correctly classified, between alive or dead tree states at a 93.75% success rate compared to 94.16% for the light curtain sensor. These results can help system designers select the most reliable sensor for the accurate detection and localization of each tree in a nursery, which might allow labor-intensive tasks, such as weeding, to be automated without damaging crops.

Probabilistic approach for longitudinal ventilation system design in fire situations

The main objective of ventilation systems in tunnels is to reach the highest possible safety level both in service and fire situation; being the fire one, the most relevant when designing the system. When designing a longitudinal ventilation system, the methodology to evaluate the capacity of the system is similar both in service and fire situation, with the exception of the chimney effect and the phenomena of thermal transfer which is responsible or the changes in the density of the air. When facing the dimensioning task for longitudinal ventilated tunnels, although similar methodologies are used in different countries, specific hypothesis (aerodynamic, thermal properties, traffic) even if discussed in the literature or current practice, are not usually detailed in the regulations or recommendations. The aim of this paper is to propose a probabilistic approach to the problem which would allow the designer, and the tunnel owner, to understand the uncertainty and sensibility adopted in the results and, eventually, identify possible ways of optimizing the ventilation solution to be adopted.

Ventilation and FFFS fire tests for “Calle 30” road tunnels

Between 2003 and 2007 an urban network or road tunnels with a total constructed tubes length of 45 km was built in the city of Madrid. This amazing engineering work, known as "Calle 30 Project" counted with different kinds of tunnel typologies and ventilation systems. Due to the length of the tunnels and the impact of the work itself, the tunnels were endowed with a great variety of installations to provide the maximum levels of safety both for users and the infrastructure includieng, in some parts of the tunnel, fixed fire fighting system based on water mist. Whithin this framework a large-scale programme of fire tests was planned to study different aspects related to fire safety in the tunnels including the phenomena of the interaction between ventilation and extinguishing system. In addition, these large scale fire tests allowed fire brigades of the city of Madrid an opportunity to define operational procedures for specific fire fighting in tunnels and evaluate the possibilities of fixed fire fighting systems. The tests were carried out in the Center of Experimentation "San pedro of Anes" which includes a 600 m tunnel with a removable false ceiling for reproducing different ceiling heights and ventilation conditions (transverse and longitudinal ones). Interesting conclusions on the interaction of ventilation and water mist systems were obtained but also on other aspects including performance of water mist system in terms of reduction of gas temperatures or visibility conditions. This paper presents a description of the test's programme carried out and some previous results obtained.

Large Scale Fire Tests for the “Calle 30 Project"

Between 2003 and 2007 an urban network of road tunnels with a total constructed tubes length of 45 km was built in the city of Madrid. This amazing engineering work, known as “Calle30 Project” counted with different kinds of tunnel typologies and ventilation systems. Due to the length of the tunnels and the impact of the work itself, the tunnels were endowed with a great variety of installations to provide the maximum levels of safety both for users and the infrastructure including,in some parts of the tunnel, fixed fire fighting system based on water mist. Within this framework a large-scale campaign of fire tests were planned to study different aspects related to fire safety in the tunnels including the phenomena of the interaction between ventilation and extinction system. In addition, this large scale fire tests allowed fire brigades of the city of Madrid an opportunity to define operational procedures for specific fire fighting in tunnels and evaluate the possibilities of fixed fire fighting systems. The tests were carried out in the Center of Experimentation "San Pedro of Anes" which counts with a 600 m tunnel with a removable false ceiling for reproducing different ceiling heights and ventilation conditions (transverse and longitudinal ones). Interesting conclusions on the interaction of ventilation and water mist systems were obtained but also on other aspects including performance of water mist system in terms of reduction of gas temperatures or visibility conditions. This paper presents a description of the test’s campaign carried out and some previous results obtained.

Sistema de autenticación accesible para el hogar digital

El Hogar Digital Accesible (HDA) de la ETSIST nace con el propósito de acercar las nuevas Tecnologías de la Información a las personas que precisan de necesidades concretas de accesibilidad y usabilidad, dotándoles de herramientas que les permitan aumentar su calidad de vida, confort, seguridad y autonomía. El entorno del HDA consta de elementos de control para puertas, persianas, iluminación, agua o gas, sensores de temperatura, incendios, gas, sistemas de climatización, sistemas de entretenimiento y sistemas de seguridad tales como detectores de presencia y alarmas. Todo ello apoyado sobre una arquitectura de red que proporciona una pasarela residencial y un acceso a banda ancha. El objetivo principal de este PFG ha sido el desarrollo de un sistema de autenticación para el Hogar Digital Accesible de bajo coste. La idea de integrar un sistema de autenticación en el HDA, surge de la necesidad de proteger de accesos no deseados determinados servicios disponibles dentro de un ámbito privado. Algunos de estos servicios pueden ser tales como el acceso a la lectura de los mensajes disponibles en el contestador automático, el uso de equipos multimedia, la desconexión de alarmas de seguridad o simplemente la configuración de ambientes según el usuario que esté autenticado (intensidad de luz, temperatura de la sala, etc.). En el desarrollo han primado los principios de accesibilidad, usabilidad y seguridad necesarios para la creación de un entorno no invasivo, que permitiera acreditar la identidad del usuario frente al sistema HDA. Se ha planteado como posible solución, un sistema basado en el reconocimiento de un trazo realizado por el usuario. Este trazo se usará como clave de cara a validar a los usuarios. El usuario deberá repetir el trazado que registró en el sistema para autenticarse. Durante la ejecución del presente PFG, se justificará la elección de este mecanismo de autenticación frente a otras alternativas disponibles en el mercado. Para probar la aplicación, se ha podido contar con dos periféricos de distintas gamas, el uDraw creado para la PS3 que se compone de una tableta digitalizadora y un lápiz que permite recoger los trazos realizados por el usuario de forma inalámbrica y la tableta digitalizadora Bamboo de Wacom. La herramienta desarrollada permite a su vez, la posibilidad de ser usada por otro tipo de dispositivos como es el caso del reloj con acelerómetro de 3 ejes de Texas Instruments Chronos eZ430 capaz de trasladar los movimientos del usuario al puntero de un ratón. El PFG se encuentra dividido en tres grandes bloques de flujo de trabajo. El primero se centra en el análisis del sistema y las tecnologías que lo componen, incluyendo los distintos algoritmos disponibles para realizar la autenticación basada en reconocimiento de patrones aplicados a imágenes que mejor se adaptan a las necesidades del usuario. En el segundo bloque se recoge una versión de prueba basada en el análisis y el diseño UML realizado previamente, sobre la que se efectuaron pruebas de concepto y se comprobó la viabilidad del proyecto. El último bloque incluye la verificación y validación del sistema mediante pruebas que certifican que se han alcanzado los niveles de calidad necesarios para la consecución de los objetivos planteados, generando finalmente la documentación necesaria. Como resultado del trabajo realizado, se ha obtenido un sistema que plantea una arquitectura fácilmente ampliable lograda a través del uso de técnicas como la introspección, que permiten separar la lógica de la capa de negocio del código que la implementa, pudiendo de forma simple e intuitiva sustituir código mediante ficheros de configuración, lo que hace que el sistema sea flexible y escalable. Tras la realización del PFG, se puede concluir que el producto final obtenido ha respondido de forma satisfactoria alcanzando los niveles de calidad requeridos, siendo capaz de proporcionar un sistema de autenticación alternativo a los convencionales, manteniendo unas cotas de seguridad elevadas y haciendo de la accesibilidad y el precio sus características más reseñables. ABSTRACT. Accessible Digital Home (HDA) of the ETSIST was created with the aim of bringing the latest information and communications technologies closer to the people who has special needs of accessibility and usability increasing their quality of life, comfort, security and autonomy. The HDA environment has different control elements for doors, blinds, lighting, water or gas, temperature sensors, fire protection systems, gas flashover, air conditioning systems, entertainments systems and security systems such as intruders detectors and alarms. Everything supported by an architecture net which provides a broadband residential services gateway. The main goal of this PFG was the development of a low-cost authentication system for the Accessible Digital Home. The idea of integrating an authentication system on the HDA, stems from the need to safeguard certain private key network resources from unauthorized access. Some of said resources are the access to the answering machine messages, the use of multimedia devices, the alarms deactivation or the parameter settings for each environment as programmed by the authenticated user (light intensity, room temperature, etc.). During the development priority was given to concepts like accessibility, usability and security. All of them necessary to create a non invasive environment that allows the users to certify their identity. A system based on stroke pattern recognition, was considered as a possible solution. This stroke is used as a key to validate users. The user must repeat the stroke that was saved on the system to validate access. The selection of this authentication mechanism among the others available options will be justified during this PFG. Two peripherals with different ranges were used to test the application. One of them was uDraw design for the PS3. It is wireless and is formed by a pen and a drawing tablet that allow us to register the different strokes drawn by the user. The other one was the Wacom Bamboo tablet, that supports the same functionality but with better accuracy. The developed tool allows another kind of peripherals like the 3-axes accelerometer digital wristwatch Texas Instruments Chronos eZ430 capable of transfering user movements to the mouse cursor. The PFG is divided by three big blocks that represent different workflows. The first block is focused on the system analysis and the technologies related to it, including algorithms for image pattern recognition that fits the user's needs. The second block describes how the beta version was developed based on the UML analysis and design previously done. It was tested and the viability of the project was verified. The last block contains the system verification and validation. These processes certify that the requirements have been fulfilled as well as the quality levels needed to reach the planned goals. Finally all the documentation has been produced. As a result of the work, an expandable system has been created, due to the introspection that provides the opportunity to separate the business logic from the code that implements it. With this technique, the code could be replaced throughout configuration files which makes the system flexible and highly scalable. Once the PFG has finished, it must therefore be concluded that the final product has been a success and high levels of quality have been achieved. This authentication tool gives us a low-cost alternative to the conventional ones. The new authentication system remains security levels reasonably high giving particular emphasis to the accessibility and the price.

An eco-friendly way to fire retardant flexible polyurethane foam: layer-by-layer assembly of fully bio-based substances

The objective of the present study is to develop fully renewable and environmentally benign techniques for improving the fire safety of flexible polyurethane foams (PUFs). A multilayered coating made from cationic chitosan (CS) and anionic alginate (AL) was deposited on PUFs through layer-by-layer assembly. This coating system exhibits a slight influence on the thermal stability of PUF, but significantly improves the char formation during combustion. Cone calorimetry reveals that 10 CS-AL bilayers (only 5.7% of the foams weight) lead to a 66% and 11% reduction in peak heat release rate and total heat release, respectively, compared with those of the uncoated control. The notable decreased fire hazards of PUF are attributed to the CS-AL coatings being beneficial to form an insulating protective layer on the surface of burning materials that inhibits the oxygen and heat permeation and slows down the flammable gases in the vapor phase, and thereby improves the flame resistance. This water-based, environmentally benign natural coating will stimulate further efforts in improving fire safety for a variety of polymer substrates.

Uncertainty in optical bio-sensors due to the spectral displacement of the interference modes of the transduction signal. Incertidumbre en bio-sensores ópticos asociada al desplazamiento espectral de los modos de interferencia de la señal de transducción

The analysis of the interference modes has an increasing application, especially in the field of optical biosensors. In this type of sensors, the displacement Δν of the interference modes of the transduction signal is observed when a particular biological agent is placed over the biosensor. In order to measure this displacement, the position of a maximum (or a minimum) of the signal must be detected before and after placing the agent over the sensor. A parameter of great importance for this kind of sensors is the period Pν of the signal, which is inversely proportional to the optical thickness h0 of the sensor in the absence of the biological agent. The increase of this period improves the sensitivity of the sensor but it worsens the detection of the maximum. In this paper, authors analyze the propagation of uncertainties in these sensors when using least squares techniques for the detection of the maxima (or minima) of the signal. Techniques described in supplement 2 of the ISO-GUM Guide are used. The result of the analysis allows a metrological educated answer to the question of which is the optimal period Pν of the signal. El análisis del comportamiento de los modos de interferencia tiene una aplicación cada vez más amplia, especialmente en el campo de los biosensores ópticos. En este tipo de sensores se observa el desplazamiento Δν de los modos de interferencia de la señal de transducción al reconocer un de-terminado agente biológico. Para medir ese desplazamiento se debe detectar la posición de un máximo o mínimo de la señal antes y después de dicho desplazamiento. En este tipo de biosensores un parámetro de gran importancia es el periodo Pν de la señal el cual es inversamente proporcional al espesor óptico h0 del sensor en ausencia de agente biológico. El aumento de dicho periodo mejora la sensibilidad del sensor pero parece dificultar la detección del mínimo o máximo. Por tanto, su efecto sobre la incertidumbre del resultado de la medida presenta dos efectos contrapuestos: la mejora de la sensibilidad frente a la dificultad creciente en la detección del mínimo ó máximo. En este trabajo, los autores analizan la propagación de incertidumbres en estos sensores utilizando herramientas de ajuste por MM.CC. para la detección de los mínimos o máximos de la señal y técnicas de propagación de incertidumbres descritas en el suplemento 2 de la Guía ISO-GUM. El resultado del análisis permite dar una respuesta, justificada desde el punto de vista metrológico, de en que condiciones es conveniente o no aumentar el periodo Pν de la señal.

On the Analytical Approach to Present Engineering Problems: Photovoltaic Systems Behavior, Wind Speed Sensors Performance, and High-Speed Train Pressure Wave Effects in Tunnels

At present, engineering problems required quite a sophisticated calculation means. However, analytical models still can prove to be a useful tool for engineers and scientists when dealing with complex physical phenomena. The mathematical models developed to analyze three different engineering problems: photovoltaic devices analysis; cup anemometer performance; and high-speed train pressure wave effects in tunnels are described. In all cases, the results are quite accurate when compared to testing measurements.

On the harmonic analysis of cup anemometer rotation speed: A principle to monitor performance and maintenance status of rotating meteorological sensors

The calibration results of one anemometer equipped with several rotors, varying their size, were analyzed. In each case, the 30-pulses pert turn output signal of the anemometer was studied using Fourier series decomposition and correlated with the anemometer factor (i.e., the anemometer transfer function). Also, a 3-cup analytical model was correlated to the data resulting from the wind tunnel measurements. Results indicate good correlation between the post-processed output signal and the working condition of the cup anemometer. This correlation was also reflected in the results from the proposed analytical model. With the present work the possibility of remotely checking cup anemometer status, indicating the presence of anomalies and, therefore, a decrease on the wind sensor reliability is revealed.

Influencia del tratamiento "a fuego" en las características del estuco tradicional con cal = Influence of treatment "by fire" in the characteristics of traditional lime stucco

Esta investigación avanza en el intento de recuperar la técnica tradicional del estuco a fuego, paradigma de la decoración de espacios interiores hasta la mitad del s. XX por sus imitaciones marmóreas de gran calidad. Para ejecutarlos se utilizaban morteros de cal con áridos de mármol, pigmentos minerales y grasas; con estos materiales se preparaban y tendían las masas, se pintaban al fresco y se terminaban con el paso de una herramienta metálica caliente. Como sucede con otras técnicas, el paso del tiempo ha difuminado los conocimientos sobre la materia, haciendo muy difícil la conservación o restauración de los ejemplos en nuestro patrimonio. A partir de la escasa bibliografía existente se ha recuperado el proceso, sometiendo las muestras elaboradas a diferentes ensayos que han caracterizado el acabado final,tanto en sus características intrínsecas como en las que le son conferidas al proteger finalmente las muestras con una capa de cera, tal y como se realizaba tradicionalmente.---ABSTRACT---This research advances in the attempt to recover the traditional technique of stucco by fire; paradigm of indoor decoration until half of 20th century due to its high quality marbled imitations. On its implementation process, it was used lime mortars with marble aggregates, mineral pigments and greases. With these materials, masses were prepared and extended into the walls, they were painted in fresco and ended with the passage of a heated metal tool. As with any other technique, the time passing over has blurred the knowledge on the subject, making very difficult the preservation or restoration of examples in our heritage. Despite of the limited literature, the process has been recovered; subjecting the samples prepared at different trials that have characterized the finished, both in its merits and its conferred characteristics by finally protecting the samples with a layer of wax, as was done traditionally.

Using aircraft as wind sensors for estimating accurate wind fields for air traffic management applications

A study which examines the use of aircraft as wind sensors in a terminal area for real-time wind estimation in order to improve aircraft trajectory prediction is presented in this paper. We describe not only different sources in the aircraft systems that provide the variables needed to derivate the wind velocity but the capabilities which allow us to present this information for ATM Applications. Based on wind speed samples from aircraft landing at Madrid-Barajas airport, a real-time wind field will be estimated using a data processing approach through a minimum variance method. Finally the accuracy of this procedure will be evaluated for this information to be useful to Air Traffic Control.

Exploring new roles for the rpoS gene in the survival and virulence of the fire blight pathogen Erwinia amylovora

Erwinia amylovora causes fire blight in economically important plants of the family Rosaceae. This bacterial pathogen spends part of its life cycle coping with starvation and other fluctuating environmental conditions. In many Gram-negative bacteria, starvation and other stress responses are regulated by the sigma factor RpoS. We obtained an E. amylovora rpoS mutant to explore the role of this gene in starvation responses and its potential implication in other processes not yet studied in this pathogen. Results showed that E. amylovora needs rpoS to develop normal starvation survival and viable but nonculturable (VBNC) responses. Furthermore, this gene contributed to stationary phase cross-protection against oxidative, osmotic, and acid stresses and was essential for cross-protection against heat shock, but nonessential against acid shock. RpoS also mediated regulation of motility, exopolysaccharide synthesis, and virulence in immature loquats, but not in pear plantlets, and contributed to E. amylovora survival in nonhost tissues during incompatible interactions. Our results reveal some unique roles for the rpoS gene in E. amylovora and provide new knowledge on the regulation of different processes related to its ecology, including survival in different environments and virulence in immature fruits.

Vegetation and fire history since the last glacial maximum in an inland area of the western Mediterranean Basin (Northern Iberian Plateau, NW Spain)

We reconstructed vegetation responses to climate oscillations, fire and human activities since the last glacial maximum in inland NW Iberia, where previous paleoecological research is scarce. Extremely sparse and open vegetation composed of steppic grasslands and heathlands with scattered pioneer trees suggests very cold and dry conditions during the Oldest Dryas, unsuitable for tree survival in the surroundings of the study site. Slight woodland expansion during the Bolling/Allerod was interrupted by the Younger Dryas cooling. Pinewoods dominated for most of the early Holocene, when a marked increase in fire activity occurred. Deciduous trees expanded later reaching their maximum representation during the mid-Holocene. Enhanced fire activity and the presence of coprophilous fungi around 6400-6000 cal yr BP suggest an early human occupation around the site. However, extensive deforestation only started at 4500 calyrBP, when fire was used to clear the tree canopy. Final replacement of woodlands with heathlands, grasslands and cereal crops occurred from 2700 cal yr BP onwards due to land-use intensification. Our paleoecological record can help efforts aimed at restoring the natural vegetation by indicating which communities were dominant at the onset of heavy human impact, thus promoting the recovery of currently rare oak and alder stands.

Debonding identification in FRP-plated RC structures using PZT sensors

The application of the Electro-Mechanical Impedance (EMI) method for damage detection in Structural Health Monitoring has noticeable increased in recent years. EMI method utilizes piezoelectric transducers for directly measuring the mechanical properties of the host structure, obtaining the so called impedance measurement, highly influenced by the variations of dynamic parameters of the structure. These measurements usually contain a large number of frequency points, as well as a high number of dimensions, since each frequency range swept can be considered as an independent variable. That makes this kind of data hard to handle, increasing the computational costs and being substantially time-consuming. In that sense, the Principal Component Analysis (PCA)-based data compression has been employed in this work, in order to enhance the analysis capability of the raw data. Furthermore, a Support Vector Machine (SVM), which has been widespread used in machine learning and pattern recognition fields, has been applied in this study in order to model any possible existing pattern in the PCAcompress data, using for that just the first two Principal Components. Different known non-damaged and damaged measurements of an experimental tested beam were used as training input data for the SVM algorithm, using as test input data the same amount of cases measured in beams with unknown structural health conditions. Thus, the purpose of this work is to demonstrate how, with a few impedance measurements of a beam as raw data, its healthy status can be determined based on pattern recognition procedures.

Methodology based on FBG sensors for monitoring of FRP-strengthened beams

Advanced composite materials are increasingly used in the strengthening of reinforced concrete (RC) structures. The use of externally bonded strips made of fibre-reinforced plastics (FRP) as strengthening method has gained widespread acceptance in recent years since it has many advantages over the traditional techniques. However, unfortunately, this strengthening method is often associated with a brittle and sudden failure caused by some form of FRP bond failure, originated at the termination of the FRP material or at intermediate areas in the vicinity of flexural cracks in the RC beam. Up to date, little effort in the early prediction of the debonding in its initial instants even though this effect is not noticeable by simple visual observation. An early detection of this phenomenon might help in taking actions to prevent future catastrophes. Fibre-optic Bragg grating (FBG) sensors are able to measure strains locally with high resolution and accuracy. Furthermore, as their physical size is extremely small compared with other strain measuring components, it enables to be embedded at the concrete-FRP interface for determining the strain distribution without influencing the mechanical properties of the host materials. This paper shows the development of a debonding identification methodology based on strains experimentally measured. For, it a simplified model is implemented to simulate the behaviour of FRP-strengthened reinforced concrete beams. This model is taken as a basis to. develop an model updating procedure able to detect minor debonding at the concrete-FRP interface from experimental strains obtained by using FBG sensors embedded at the interface