Hysteresis phenomena in transverse galloping of triangular cross-section bodies

Transverse galloping is a type of aeroelastic instability characterised by large amplitude, low frequency oscillation of a structure in the direction normal to the mean wind direction. It normally appears in bodies with small stiffness and structural damping, provided the incident flow velocity is high enough. In the simplest approach transverse galloping can be considered as a one-degree-of-freedom oscillator subjected to aerodynamic forces, which in turn can be described by using a quasi-steady description. In this frame it has been demonstrated that hysteresis phenomena in transverse galloping is related to the existence of inflection points in the curve giving the dependence with the angle of attack of the aerodynamic coefficient normal to the incident flow. Aiming at experimentally checking such a relationship between these inflection points and hysteresis, wind tunnel experiments have been conducted. Experiments have been restricted to isosceles triangular cross-section bodies, whose galloping behaviour is well documented. Experimental results show that, according to theoretical predictions, hysteresis takes place at the angles of attack where there are inflection points in the lift coefficient curve, provided that the body is prone to gallop at these angles of attack.

Influence of open trailing edge on laminar aerofoils at low Reynols number

This article deals with the effect of open trailing edge on the aerodynamic characteristics of laminar aerofoils at low Reynolds numbers, the attention being focussed on the influence of such a trailingedge imperfection on the aerodynamic efficiency. Wind tunnel tests have been performed at different Reynolds numbers and angles of attack, and global aerodynamic as well as pressure distributions were measured (in these tests two types of open trailing edges, either sharp or rounded were considered). From experimental results, a quantitative analysis of the influence of the trailing-edge thickness on the degradation of aerofoil aerodynamic performances has been obtained, which allows the establishment of a criterion for an acceptance limit for this kind of imperfection.

Effect of the Wake of the Transducer Supports on the Ultrasonic Anemometer Measurements

The wake produced by the structural supports of the ultrasonic anemometers (UAs)causes distortions in the velocity field in the vicinity of the sonic path. These distortions are measured by the UA, inducing errors in the determination of the mean velocity, turbulence intensity, spectrum, etc.; basic parameters to determine the effect of wind on structures. Additionally, these distortions can lead to indefinition in the calibration function of the sensors (Cuerva et al., 2004). Several wind tunnel tests have been dedicated to obtaining experimental data, from which have been developed fit models to describe and to correct these distortions (Kaimal, 1978 and Wyngaard, 1985). This work explores the effect of a vortex wake generated by the supports of an UA, on the measurement of wind speed done by this instrument. To do this, the Von Karman¿s vortex street potential model is combined with the mathematical model of the measuring process carried out by UAs developed by Franchini et al. (2007). The obtained results are the correction functions of the measured wind velocity, which depends on the geometry of the sonic anemometer and aerodynamic conditions. These results have been validated with the ones obtained in a wind tunnel test done on a single path UA, especially developed for research. The supports of this UA have been modified in order to reproduce the conditions of the theoretical model. Good agreements between experimental and theoretical results have been found.

Influence of leading edge imperfections on the aerodynamic characterictics of NACA 632-215 laminar aerofoils at low Reynolds number

This article deals with the effect of leading edge imperfections on the aerodynamic characteristics of a NACA 632-215 laminar aerofoil at low Reynolds numbers. Wind tunnel tests have been performed at different Reynolds numbers and angles of attack and global aerodynamic loads were measured. To perform these tests, a NACA 632-215 aerofoil was built up in two halves (corresponding to the upper side and to the lower side), the leading edge imperfection here considered being a slight displacement of half aerofoil with respect to the other. From experimental results, a quantitative measure of the influence of the leading edge displacement on the degradation of the aerofoil aerodynamic performances has been obtained. This allows the establishment of a criterion for an acceptance limit for this kind of imperfection

An experimental and theoretical study of unsteady flow (gust) effects on structures

The gust wind tunnel at IDR, Universidad Politécnica de Madrid (UPM), has been enhanced and the impact of the modification has been characterized. Several flow quality configurations have been tested. The problems in measuring gusty winds with Pitot tubes have been considered. Experimental results have been obtained and compared with theoretically calculated results (based on potential flow theory). A theoretical correction term has been proposed for unsteady flow measurements obtained with Pitot tubes. The effect of unsteady flow on structures and laying bodies on the ground has been also considered. A theoretical model has been proposed for a semi-circular cylinder and experimental tests have been performed to study the unsteady flow effects, which can help in clarifying the phenomenon.

A 2D computational parametric analysis of the sheltering effect of fences on a railway vehicle standing on a bridge and experiencing crosswinds

In a crosswind scenario, the risk of high-speed trains overturning increases when they run on viaducts since the aerodynamic loads are higher than on the ground. In order to increase safety, vehicles are sheltered by fences that are installed on the viaduct to reduce the loads experienced by the train. Windbreaks can be designed to have different heights, and with or without eaves on the top. In this paper, a parametric study with a total of 12 fence designs was carried out using a two-dimensional model of a train standing on a viaduct. To asses the relative effectiveness of sheltering devices, tests were done in a wind tunnel with a scaled model at a Reynolds number of 1 × 105, and the train’s aerodynamic coefficients were measured. Experimental results were compared with those predicted by Unsteady Reynolds-averaged Navier-Stokes (URANS) simulations of flow, showing that a computational model is able to satisfactorily predict the trend of the aerodynamic coefficients. In a second set of tests, the Reynolds number was increased to 12 × 106 (at a free flow air velocity of 30 m/s) in order to simulate strong wind conditions. The aerodynamic coefficients showed a similar trend for both Reynolds numbers; however, their numerical value changed enough to indicate that simulations at the lower Reynolds number do not provide all required information. Furthermore, the variation of coefficients in the simulations allowed an explanation of how fences modified the flow around the vehicle to be proposed. This made it clear why increasing fence height reduced all the coefficients but adding an eave had an effect mainly on the lift force coefficient. Finally, by analysing the time signals it was possible to clarify the influence of the Reynolds number on the peak-to-peak amplitude, the time period and the Strouhal number.

Fourier analysis of the aerodynamic behavior of cup anemometers

The calibration results (the transfer function) of an anemometer equipped with several cup rotors were analyzed and correlated with the aerodynamic forces measured on the isolated cups in a wind tunnel. The correlation was based on a Fourier analysis of the normal-to-the-cup aerodynamic force. Three different cup shapes were studied: typical conical cups, elliptical cups and porous cups (conical-truncated shape). Results indicated a good correlation between the anemometer factor, K, and the ratio between the first two coefficients in the Fourier series decomposition of the normal-to-the-cup aerodynamic force

Influence of aerodynamic characteristics of H beams on galloping stability

This paper presents the experimental study developed on a prismatic beam with H section, sometimes used in bridges as suspenders, vertical bars or decks. The purpose of this study is to understand the physical behavior of the air around this type of section, in order to reduce the aerodynamic loads, the onset speed of galloping and even to avoid it. To achieve this, a study of the influence of all geometric parameters that define the section has been developed. Previously, the most interesting configurations have been selected using a smoke flow visualization technique in the wind-tunnel, then the corresponding static aerodynamic loads were measured, completed with dynamic tests and, finally, the parameters governing the phenomenon of galloping determined.

Static and Dynamic Experimental Analysis of the Galloping Stability of Porous H-Section Beams

The phenomenon of self-induced vibrations of prismatic beams in a cross-flow has been studied for decades, but it is still of great interest due to their important effects in many different industrial applications. This paper presents the experimental study developed on a prismatic beam with H-section.The aim of this analysis is to add some additional insight into the behaviour of the flow around this type of bodies, in order to reduce galloping and even to avoid it. The influence of some relevant geometrical parameters that define the H-section on the translational galloping behaviour of these beams has been analysed. Wind loads coefficients have been measured through static wind tunnel tests and the Den Hartog criterion applied to elucidate the influence of geometrical parameters on the galloping properties of the bodies under consideration.These results have been completed with surface pressure distribution measurements and, besides, dynamic tests have been also performed to verify the static criterion. Finally, the morphology of the flow past the tested bodies has been visualised by using smoke visualization techniques. Since the rectangular section beam is a limiting case of the H-section configuration, the results here obtained are compared with the ones published in the literature concerning rectangular configurations; the agreement is satisfactory.

Investigación experimental del flujo aerodinámico sobre helipuertos embarcados

La investigación del flujo aerodinámico sobre helipuertos embarcados se encuentra estrechamente relacionada con la operación segura de las aeronaves, pues las condiciones del flujo que tiene lugar en ese entorno pueden exceder los límites para los que están certificadas dichas aeronaves. El ambiente aerodinámico en las inmediaciones de un barco es altamente complejo y se encuentra influenciado por gran número de factores (chimeneas, antenas, mástiles, etc.) relacionados con la configuración específica del propio barco. El flujo objeto de investigación corresponde a la estela que se desarrolla sobre la cubierta de vuelo de una fragata, el cual está fuertemente influenciado por la superestructura de la misma, y que cualitativamente es similar al flujo que tiene lugar entre edificios altos o helipuertos situados en áreas urbanas, pues comprende estructuras tipo caja, con bordes afilados, que generan flujos tridimensionales altamente turbulentos. En esta Tesis se aborda el estudio del problema desde el punto de vista experimental, mediante simulación en túnel aerodinámico y medida de las variables del campo fluido sobre maquetas de fragatas a escala reducida. Las herramientas empleadas para tal cometido, han sido técnicas experimentales, tales como la visualización del flujo, la velocimetría láser por imágenes de partículas, la anemometría láser Doppler y los scanners electrónicos de presión, que han permitido investigar el flujo problema con objeto de obtener información, y adquirir así, un conocimiento más profundo de dicho flujo. La explotación de este conocimiento, ha dado lugar al diseño de una nueva solución, basada en la modificación de geometría básica de la fragata, por medio del cambio de la curvatura del techo del hangar, permitiendo suavizar el escalón descendente que se produce aguas abajo del mismo. Las geometrías modificadas han sido ensayada en túnel mediante la misma metodología empleada para la fragata original, de modo que, ha podido establecerse un análisis comparativo, para valorar la efectividad de la solución propuesta, el cual ha mostrado resultados satisfactorios, retirando el flujo adverso de la zona de operación de helicópteros y desplazándolo hacia el hangar, donde resulta menos peligroso, de modo que se reduce la carga del piloto y los riesgos de accidente durante las operaciones a bordo de embarcaciones. ABSTRACT The investigation of aerodynamic flow above the ship’s heliports is directly related to the aircraft safe operation, because the environment flow conditions may exceed the aircraft certification limits. Aerodynamic ship’s environment is highly complex and it is influenced by a large number of factors (stacks, antennae, masts, …) related to each specific ship configuration. The flow under investigation occurs into the wake produced above the flight deck of a frigate, that is strongly influenced by the superstructure. This flow is similar to one produced around tall buildings or heliports located in urban areas, thus in both of them, the air is flowing around sharp-edges box-like structures, producing three-dimensional and highly turbulent flows. This Thesis studies the problem from an experimental point of view, by means of wind tunnel simulations and measurements of the flow field around reduced scale frigates models. Tools used in this work are the experimental techniques, as flow visualization, particle image velocimetry, laser Doppler anemometry and pressure electronic scanners. These techniques provide information about the flow in order to obtain a more complete insight of this kind of flows. The exploitation of this insight is used for the design of a new flow control concept, based on the modification of the basic frigate geometry. This new design consists in the hangar roof curvature modification that produces a smoothing of the descendent step located downstream the hangar. Modified geometries are tested in wind tunnel by means of the same methodology as the original frigate, thus a comparative analysis is established in order to perform an assessment of effectiveness. This analysis has shown good results in displacing the adverse flow from the helicopter operation path to the nearest hangar region, reducing the pilot load and the accident risks during on board operations.

Aerodynamic Study of Airfoils with Leading Edge Imperfections at Low Reynolds Number

A study has been made on the influence of the leading edge imperfections in airfoils used in different devices relating their aerodynamic performances. Wind tunnel tests have been made at different Reynolds numbers and angle of attacks in order to show this effect. Later, a quantitative study of the aerodynamic properties has been made based on the different leading edge imperfections and their size.

Fenómenos de galope en piezas prismáticas con sección en H

El objetivo de esta Tesis es el estudio sistemático del fenómeno aeroelástico de galope de una viga prismática con sección transversal en H. En particular, se pretende analizar la influencia de determinados parámetros geométricos que definen la geometría de la sección y el efecto del ángulo de ataque de la corriente sobre la estabilidad del fenómeno de oscilación. El interés en el estudio de esta forma de la sección transversal de una viga se basa en el hecho de que, con cierta frecuencia, se sigue utilizando, por su buen comportamiento estructural, en construcciones civiles como tableros y tirantes de puentes de gran longitud, señalizaciones, luminarias y, en general, en grandes estructuras metálicas. Los parámetros geométricos seleccionados para su estudio son tres: el espesor de las dos alas verticales, su porosidad y el espesor de sendas ranuras en la zona de unión entre el alma y las alas de la sección. Inicialmente se han realizado ensayos estáticos en un túnel aerodinámico con objeto de obtener las cargas aerodinámicas y poder aplicar el criterio casi-estático de Glauert - Den Hartog. En estos ensayos, se han medido tanto las fuerzas de sustentación y resistencia aerodinámicas como las distribuciones de presiones en la superficie de la zona central de la sección. Posteriormente, se han realizado ensayos de visualización de flujo, utilizando un túnel de humos, para poder comprender mejor el comportamiento físico del aire alrededor del cuerpo. El estudio estático se ha completado realizando ensayos con PIV, que permiten realizar una medida precisa de la velocidad del campo fluido. Por último, se han realizado ensayos dinámicos en otro túnel aerodinámico con objeto de contrastar la aplicabilidad del criterio casi-estático, la velocidad de inicio de galope y la amplitud de las oscilaciones producidas. Los resultados muestran que el espesor de las alas verticales, aunque modifica apreciablemente la magnitud de las cargas aerodinámicas, no afecta sustancialmente a la estabilidad a galope, mientras que su porosidad sí ejerce un control efectivo que permite reducir este fenómeno e incluso evitarlo, en determinados casos. En todas las situaciones el criterio de Glauert-Glauert - Den Hartog ha resultado ser aplicable y, en ocasiones, más restrictivo que los resultados obtenidos en ensayos dinámicos. La presencia de una ranura en la zona de unión entre el alma y las dos alas, o su combinación con la porosidad en las alas, reduce la intensidad de galope, incrementando la velocidad crítica de su inicio, pero no logra hacer que desaparezca, como se justificará en el desarrollo del trabajo. ABSTRACT Galloping is a type of aeroelastic instability characterized by a large amplitude oscillation at the natural frequency of the structure, producing normal motion to wind. It usually occurs in slender bodies lightly damped at sufficiently high speeds. In this thesis an experimental study has been developed on the galloping instability of a beam with H cross section, which is inscribed in a rectangle with a slender 1: 2. A systematic study has been carried out of the influence of three different geometric parameters on galloping, in the range of 0 to 90° angle of attack of the incoming stream. These parameters are the thickness of the flanges of the section, the porosity of the flanges, the thickness of two slots along the span, in the area between the flange and the central core of the section, and the combination effect of the last two parameters. First of all, static tests have been performed in a wind tunnel to determine the lift and drag forces by using a balance and then the quasi-static stability criterion due to Glauert-Den Hartog has been determined. Later, to better understand and verify the results previously obtained, it has also been tested the pressure distribution on the surface of the model, flow visualization in a second, smoke, wind tunnel, and Particle Image Velocimetry (PIV) study of the flow around the section, in a third tunnel. Finally, dynamic tests have been performed, on a fourth wind tunnel, for determining the amplitude and frequency of the oscillations in each case. The results have been collected in stability diagrams for each geometric parameter studied. These results show that the more critical angles of attack of the stream for galloping behavior are close to 0 and 90º. It has been found that the thickness of the flanges, although changes the galloping behavior on the section, does not reduce it substantially. However, the porosity in the flanges has been proved to be an efficient control mechanism on galloping, and even above 40% porosity, it disappears. The thickness of the slot studied and its combination with the porosity in the flanges in some cases reduces the aerodynamic forces appreciably but fail to prevent galloping at all angles of attack.

Transverse galloping of two-dimensional bodies having a rhombic cross-section

Transverse galloping is a type of aeroelastic instability characterized by oscillations perpendicular to wind direction, large amplitude and low frequency, which appears in some elastic two-dimensional bluff bodies when they are subjected to an incident flow, provided that the flow velocity exceeds a threshold critical value. Understanding the galloping phenomenon of different cross-sectional geometries is important in a number of engineering applications: for energy harvesting applications the interest relies on strongly unstable configurations but in other cases the purpose is to avoid this type of aeroelastic phenomenon. In this paper the aim is to analyze the transverse galloping behavior of rhombic bodies to understand, on the one hand, the dependence of the instability with a geometrical parameter such as the relative thickness and, on the other hand, why this cross-section shape, that is generally unstable, shows a small range of relative thickness values where it is stable. Particularly, the non-galloping rhombus-shaped prism?s behavior is revised through wind tunnel experiments. The bodies are allowed to freely move perpendicularly to the incoming flow and the amplitude of movement and pressure distributions on the surfaces is measured.

On the harmonic analysis of cup anemometer rotation speed: A principle to monitor performance and maintenance status of rotating meteorological sensors

The calibration results of one anemometer equipped with several rotors, varying their size, were analyzed. In each case, the 30-pulses pert turn output signal of the anemometer was studied using Fourier series decomposition and correlated with the anemometer factor (i.e., the anemometer transfer function). Also, a 3-cup analytical model was correlated to the data resulting from the wind tunnel measurements. Results indicate good correlation between the post-processed output signal and the working condition of the cup anemometer. This correlation was also reflected in the results from the proposed analytical model. With the present work the possibility of remotely checking cup anemometer status, indicating the presence of anomalies and, therefore, a decrease on the wind sensor reliability is revealed.

Galloping instabilities of Z-shaped shading louvers

Modern design of civil constructions such as office blocks, airport terminal buildings, factories, etc. incorporates more and more environmental considerations that lead to, amongst other elements, the use of glazed façades with shading devices to optimize energy consumption. These shading devices, normally slats or louvers, are very flexible structures exposed to the action of wind, and therefore aeroelastic effects such as galloping must be taken into account in their design. A typical cross-section for such elements is a Z-shaped profile made out of a central web and two side wings. The results of a parametric analysis based on static wind tunnel tests and performed on different Z-shaped louvers to determine translational galloping instability regions are presented in this paper.