Conformación de Superficies Reflectoras de Sistemas Dobles de Tipo Offset con Alimentadores descritos en Campo Próximo

This work discusses an iterative procedure of shaping offset dual-reflector antennas based on geometrical optics considering both far-field and near-field measurements of amplitude and phase from the feed horn. The surfaces synthesized will transform a known radiation field of a feed to a desired aperture distribution. This technique is applied for both circular and elliptical apertures and has the advantage to simplify the problem compared with existing techniques based on solving nonlinear differential equations. A MATLAB tool has been developed to implement the shaping algorithms. This procedure is applied for the design of a 1.1 m high-gain antenna for the ESA’s Solar Orbiter spacecraft. This antenna operating at X-band will manage high data rate and high efficiency communications with Earth stations.

Medidas de propiedades dieléctricas de materiales de construcción mediante elipsometría

A set of measurements of electromagnetic properties of building materials is presented in this work. The method is based on the measurement of the polarization state of the reflected signal from the material under study at a fixed angle of incidence. From the measured data, by using the Fresnel equations, it has been obtained the dielectric constant. Measurements were done by using two horn antennas at the frequency of 9 GHz. The obtained results are compared with the free space reflexion and transmission Fresnel method and other reflection methods based on a conductor waveguide. The method explained in this work can be used for other type of materials and its main advantage is the non-destructive character and the ease implementation.

Diseño de una rectena de onda completa de triple frecuencia

Modern communication systems use multifrequency or broadband antennas in order to provide multiple communication services. One of the biggest problems associated to all these systems comes from their batteries life cycle. Nowadays, great efforts are being undertaken in order to harvest energy from as many places as possible. In addition, if the two cycles of the corresponding wave could be used, it would be good in order to increase the RF-DC power conversion. This paper presents a multifrequency and full wave-rectifying antenna for microwave application

Study of the II Network as the Compound Slot Equivalent Circuit Model

A combination of Method of Moments (MoM) and compound slot Equivalent Circuit Model for linear array design is presented in this document. From the S Matrix of the single element, the more suitable network for its characterization is analyzed and selected. Then according to the radiation requirements of the desired array, the elements are designed and then properly connected by means of Forward Matching Procedure (FMP), which takes into account impedance matters in order to keep the input matched at the designing frequency. Comparison between HFSS simulations and MoM-FMP results are also presented. First part of this work was introduced in (1)(2) but a summary is included here to make the understanding easier.

Modulation-mode Assignment in SVD-assisted Multiuser MIMO-OFDM Systems

In order to comply with the demand on increasing available data rates in particular in wireless technologies, systems with multiple transmit and receive antennas, also called MIMO (multiple-input multiple-output) systems, have become indispensable for future generations of wireless systems. Due to the strongly increasing demand in high-data rate transmission systems, frequency non-selective MIMO links have reached a state of maturity and frequency selective MIMO links are in the focus of interest. In this field, the combination of MIMO transmission and OFDM (orthogonal frequency division multiplexing) can be considered as an essential part of fulfilling the requirements of future generations of wireless systems. However, single-user scenarios have reached a state of maturity. By contrast multiple users’ scenarios require substantial further research, where in comparison to ZF (zero-forcing) multiuser transmission techniques, the individual user’s channel characteristics are taken into consideration in this contribution. The performed joint optimization of the number of activated MIMO layers and the number of transmitted bits per subcarrier along with the appropriate allocation of the transmit power shows that not necessarily all user-specific MIMO layers per subcarrier have to be activated in order to minimize the overall BER under the constraint of a given fixed data throughput

Multibeam Network Design and Measurement for Triangular Array of Three Radiating Elements

Nowadays, more a more base stations are equipped with active conformal antennas. These antenna designs combine phase shift systems with multibeam networks providing multi-beam ability and interference rejection, which optimize multiple channel systems. GEODA is a conformal adaptive antenna system designed for satellite communications. Operating at 1.7 GHz with circular polarization, it is possible to track and communicate with several satellites at once thanks to its adaptive beam. The antenna is based on a set of similar triangular arrays that are divided in subarrays of three elements called `cells'. Transmission/Receiver (T/R) modules manage beam steering by shifting the phases. A more accurate steering of the antenna GEODA could be achieved by using a multibeam network. Several multibeam network designs based on Butler network will be presented

Modular Planar Antenna at X-band for satellite communications

An antenna which has been conceived as a portable system for satellite communications based on the recommendations ITU-R S.580-6 [1] and ITU-R S.465-5 [2] for small antennas, i.e., with a diameter lower than 50 wavelengths, is introduced. It is a planar and a compact structure with a size of 40×40×2 cm. The antenna is formed by an array of 256 printed elements covering a large bandwidth (14.7%) at X-Band. The specification includes transmission (Tx) and reception (Rx) bands simultaneously. The printed antenna has a radiation pattern with a 3dB beamwidth of 5°, over a 31dBi gain, and a dual and an interchangeable circular polarization

Portable low profile antenna at X-band

An antenna which has been conceived as a portable system for satellite communications based on the recommendations ITU-R S.580-6 and ITU-R S.465-5 for small antennas, i.e., with a diameter lower than 50 wavelengths, is introduced. It is a planar and a compact structure with a size of 40×40×2 cm. The antenna is formed by an array of 256 printed elements covering a large bandwidth (14.7%) at X-Band with a VSWR of 1.4:1. The specification includes transmission (Tx) and reception (Rx) bands simultaneously. The printed antenna has a radiation pattern with a 3dB beamwidth of 5°, over a 31dBi gain, and a dual and an interchangeable circular polarization.

Radio-holografía de microondas para la optimización de la superficie de grandes antenas reflectoras

En el presente trabajo de tesis se afronta el problema de la optimización de la superficie de grandes antenas reflectoras. Es sabido que los grandes reflectores, formados por una superficie panelada, sufren deformaciones debidas al impacto del viento, a los cambios de temperatura y a los efectos gravitacionales derivados del gran peso de la estructura. Estos efectos hacen que los reflectores pierdan su forma ideal, generalmente de paraboloide, y se reduzca su eficiencia de apertura y, por tanto, se limite la máxima frecuencia de uso de los mismos. Es necesario, por tanto, disponer de técnicas que permitan medir el estado de la superficie de grandes reflectores, y derivar los ajustes necesarios a aplicar sobre los tornillos de soporte de cada uno de los paneles que conforman dicha superficie. De esta manera, se devolvería al reflector su forma óptima y aumentaría la eficiencia de apertura y el rango de frecuencias de uso. Hay que resaltar que el aumento de la eficiencia de un radiotelescopio supone una reducción en el tiempo de integración necesario para la detección de las debilísimas señales generadas por las radiofuentes naturales, ahorrando así valioso tiempo de observación. Además, el incremento en el rango de frecuencias permite la detección de nuevas líneas o especies moleculares en dichas radiofuentes. Tras un primer capítulo introductorio, se presenta, en el capítulo segundo, la geometría de estos grandes reflectores y la influencia de los distintos factores que afectan a la calidad de la superficie de los mismos, como la gravedad, el viento y la temperatura, particularizando para el caso del radiotelescopio de 40 metros del Centro Astronómico de Yebes. En el tercer capítulo, se presentan las diferentes técnicas metrológicas empleadas actualmente para abordar la determinación de estos ajustes, mostrándose las ventajas e inconvenientes de cada una de ellas. Actualmente, la técnica metrológica más precisa y rápida para llevar a cabo esta tarea de caracterización de la superficie de un gran reflector, es la radio-holografía de microondas presentada en el capítulo cuarto. A partir de las medidas proporcionadas por esta técnica, realizadas con la ayuda de un transmisor, y mediante transformaciones de campo, se calculan los errores de la superficie del reflector, respecto al paraboloide ideal, y se derivan los ajustes necesarios. En los capítulos quinto y sexto se presentan los resultados de la aplicación de esta técnica a dos radiotelescopios: el de 30 metros de IRAM en Pico de Veleta (Granada) y los prototipos de 12 metros de las antenas del proyecto ALMA. Por su parte, el capítulo séptimo contiene el núcleo fundamental de esta tesis y presenta el desarrollo de la técnica de radio-holografía de microondas para optimizar la superficie del radiotelescopio de 40 metros del Centro Astronómico de Yebes. Para ello, ha sido necesario diseñar, construir e instalar un receptor de doble canal en banda Ku en foco primario, y la instrumentación asociada para hacer las medidas de amplitud y fase del diagrama de radiación. Además, ha sido necesario desarrollar el software para llevar a cabo las transformaciones de campo y derivar los ajustes de los paneles. De las medidas holográficas iniciales resultó un error de la superficie del radiotelescopio de 485 μm WRMS, respecto al paraboloide ideal en dirección normal. Tras varias iteraciones del proceso de medida y ajuste, se consiguió reducir dicho error a 194 μm WRMS. Esta notable mejora de la calidad de la superficie ha supuesto aumentar la eficiencia de apertura desde 2,6% al 38,2% a 86 GHz, para un receptor a esta frecuencia situado en el foco primario que produjese la misma iluminación que el receptor de holografía. In this thesis the problem of large reflector antenna surface optimization is faced. It is well known that large reflectors, which are made of a panelled surface, suffer from deformations due to the impact of wind, temperature gradients and gravity loads coming from the high weigth of the structure. These effects distort the ideal reflector shape, which is a paraboloid in most cases, hence reducing the aperture efficiency of the reflector and limiting the maximum frequency of operation. Therefore, it is necessary to have some techniques to measure the status of large reflector surfaces and to derive the adjustment values to be applied to the screws that connect the surface panels to the reflector back-up structure. In this way, the reflector would recover its optimum shape and the aperture efficiency and frequency range would increase. It has to be stated that an increment in the radiotelescope aperture efficiency would imply a reduction in the integration time needed to detect such weak signals coming from natural radiosources in space and, hence, an important saving in observation time. In addition, the increase in the frequency range of operation would allow the detection of new molecular lines in those radiosources. After the introduction, the second chapter shows the geometry of large reflector antennas and the impact on its surface quality of different factors like gravity, wind and temperature, particularly for the case of the Centro Astronómico de Yebes 40 meter radiotelescope. The third chapter deals with the different metrology techniques used to determine the panel adjustments, including the advantages and drawbacks of each one Currently, the most accurate and fast metrologic technique to carry out the characterization of large reflector surfaces is microwave radio-holography2, which is shown in chapter four. From the measurements provided by microwave radio-holography, performed with the help of a transmitter, and with the use of field transformations, the reflector surface errors are computed and the panel adjustments are derived. Chapters five and six show the results of holographic measurements applied to two first class radiotelescopes: the IRAM 30 meter radiotelescope and the 12 meter prototype antennas for the ALMA project. Chapter seven contains the main work of this thesis. It presents the development of the microwave radio-holography technique for the optimization of the Centro Astronómico de Yebes 40m radiotelescope. The work implied the design, construction and instalation of a prime focus Ku-band dual channel receiver, together with the associated instrumentation to measure the amplitude and phase of the radiotelescope radiation pattern. In addition, the software to carry out field transformations and screw settings computations was developed too. Initial holography measurements came up with an surface error of 485 μmWRMS in normal direction with respect to the best-fit paraboloid. After a few iterations of the measurementadjustment cycle, the surface error was reduced to 194 μm WRMS. This remarkable improvement in surface quality means an increment in aperture efficiency from 2,6% to 38,2% at 86 GHz, assuming a receiver at this frequency in prime focus position which produces the same illumination as the holography receiver.

Contribution to the design of waveguide-fed compound-slot arrays by means of equivalent circuit modelling

Los arrays de ranuras son sistemas de antennas conocidos desde los años 40, principalmente destinados a formar parte de sistemas rádar de navíos de combate y grandes estaciones terrenas donde el tamaño y el peso no eran altamente restrictivos. Con el paso de los años y debido sobre todo a importantes avances en materiales y métodos de fabricación, el rango de aplicaciones de este tipo de sistemas radiantes creció en gran medida. Desde nuevas tecnologías biomédicas, sistemas anticolisión en automóviles y navegación en aviones, enlaces de comunicaciones de alta tasa binaria y corta distancia e incluso sistemas embarcados en satélites para la transmisión de señal de televisión. Dentro de esta familia de antennas, existen dos grupos que destacan por ser los más utilizados: las antennas de placas paralelas con las ranuras distribuidas de forma circular o espiral y las agrupaciones de arrays lineales construidos sobre guia de onda. Continuando con las tareas de investigación desarrolladas durante los últimos años en el Instituto de Tecnología de Tokyo y en el Grupo de Radiación de la Universidad Politécnica de Madrid, la totalidad de esta tesis se centra en este último grupo, aunque como se verá se separa en gran medida de las técnicas de diseño y metodologías convencionales. Los arrays de ranuras rectas y paralelas al eje de la guía rectangular que las alimenta son, sin ninguna duda, los modelos más empleados debido a la fiabilidad que presentan a altas frecuencias, su capacidad para gestionar grandes cantidades de potencia y la sencillez de su diseño y fabricación. Sin embargo, también presentan desventajas como estrecho ancho de banda en pérdidas de retorno y rápida degradación del diagrama de radiación con la frecuencia. Éstas son debidas a la naturaleza resonante de sus elementos radiantes: al perder la resonancia, el sistema global se desajusta y sus prestaciones degeneran. En arrays bidimensionales de slots rectos, el campo eléctrico queda polarizado sobre el plano transversal a las ranuras, correspondiéndose con el plano de altos lóbulos secundarios. Esta tesis tiene como objetivo el desarrollo de un método sistemático de diseño de arrays de ranuras inclinadas y desplazadas del centro (en lo sucesivo “ranuras compuestas”), definido en 1971 como uno de los desafíos a superar dentro del mundo del diseño de antennas. La técnica empleada se basa en el Método de los Momentos, la Teoría de Circuitos y la Teoría de Conexión Aleatoria de Matrices de Dispersión. Al tratarse de un método circuital, la primera parte de la tesis se corresponde con el estudio de la aplicabilidad de las redes equivalentes fundamentales, su capacidad para recrear fenómenos físicos de la ranura, las limitaciones y ventajas que presentan para caracterizar las diferentes configuraciones de slot compuesto. Se profundiza en las diferencias entre las redes en T y en ! y se condiciona la selección de una u otra dependiendo del tipo de elemento radiante. Una vez seleccionado el tipo de red a emplear en el diseño del sistema, se ha desarrollado un algoritmo de cascadeo progresivo desde el puerto alimentador hacia el cortocircuito que termina el modelo. Este algoritmo es independiente del número de elementos, la frecuencia central de funcionamiento, del ángulo de inclinación de las ranuras y de la red equivalente seleccionada (en T o en !). Se basa en definir el diseño del array como un Problema de Satisfacción de Condiciones (en inglés, Constraint Satisfaction Problem) que se resuelve por un método de Búsqueda en Retroceso (Backtracking algorithm). Como resultado devuelve un circuito equivalente del array completo adaptado a su entrada y cuyos elementos consumen una potencia acorde a una distribución de amplitud dada para el array. En toda agrupación de antennas, el acoplo mutuo entre elementos a través del campo radiado representa uno de los principales problemas para el ingeniero y sus efectos perjudican a las prestaciones globales del sistema, tanto en adaptación como en capacidad de radiación. El empleo de circuito equivalente se descartó por la dificultad que suponía la caracterización de estos efectos y su inclusión en la etapa de diseño. En esta tesis doctoral el acoplo también se ha modelado como una red equivalente cuyos elementos son transformadores ideales y admitancias, conectada al conjunto de redes equivalentes que representa el array. Al comparar los resultados estimados en términos de pérdidas de retorno y radiación con aquellos obtenidos a partir de programas comerciales populares como CST Microwave Studio se confirma la validez del método aquí propuesto, el primer método de diseño sistemático de arrays de ranuras compuestos alimentados por guía de onda rectangular. Al tratarse de ranuras no resonantes, el ancho de banda en pérdidas de retorno es mucho mas amplio que el que presentan arrays de slots rectos. Para arrays bidimensionales, el ángulo de inclinación puede ajustarse de manera que el campo quede polarizado en los planos de bajos lóbulos secundarios. Además de simulaciones se han diseñado, construido y medido dos prototipos centrados en la frecuencia de 12GHz, de seis y diez elementos. Las medidas de pérdidas de retorno y diagrama de radiación revelan excelentes resultados, certificando la bondad del método genuino Method of Moments - Forward Matching Procedure desarrollado a lo largo de esta tésis. Abstract The slot antenna arrays are well known systems from the decade of 40s, mainly intended to be part of radar systems of large warships and terrestrial stations where size and weight were not highly restrictive. Over the years, mainly due to significant advances in materials and manufacturing methods, the range of applications of this type of radiating systems grew significantly. From new biomedical technologies, collision avoidance systems in cars and aircraft navigation, short communication links with high bit transfer rate and even embedded systems in satellites for television broadcast. Within this family of antennas, two groups stand out as being the most frequent in the literature: parallel plate antennas with slots placed in a circular or spiral distribution and clusters of waveguide linear arrays. To continue the vast research work carried out during the last decades in the Tokyo Institute of Technology and in the Radiation Group at the Universidad Politécnica de Madrid, this thesis focuses on the latter group, although it represents a technique that drastically breaks with traditional design methodologies. The arrays of slots straight and parallel to the axis of the feeding rectangular waveguide are without a doubt the most used models because of the reliability that they present at high frequencies, its ability to handle large amounts of power and their simplicity of design and manufacturing. However, there also exist disadvantages as narrow bandwidth in return loss and rapid degradation of the radiation pattern with frequency. These are due to the resonant nature of radiating elements: away from the resonance status, the overall system performance and radiation pattern diminish. For two-dimensional arrays of straight slots, the electric field is polarized transverse to the radiators, corresponding to the plane of high side-lobe level. This thesis aims to develop a systematic method of designing arrays of angled and displaced slots (hereinafter "compound slots"), defined in 1971 as one of the challenges to overcome in the world of antenna design. The used technique is based on the Method of Moments, Circuit Theory and the Theory of Scattering Matrices Connection. Being a circuitry-based method, the first part of this dissertation corresponds to the study of the applicability of the basic equivalent networks, their ability to recreate the slot physical phenomena, their limitations and advantages presented to characterize different compound slot configurations. It delves into the differences of T and ! and determines the selection of the most suitable one depending on the type of radiating element. Once the type of network to be used in the system design is selected, a progressive algorithm called Forward Matching Procedure has been developed to connect the proper equivalent networks from the feeder port to shorted ending. This algorithm is independent of the number of elements, the central operating frequency, the angle of inclination of the slots and selected equivalent network (T or ! networks). It is based on the definition of the array design as a Constraint Satisfaction Problem, solved by means of a Backtracking Algorithm. As a result, the method returns an equivalent circuit of the whole array which is matched at its input port and whose elements consume a power according to a given amplitude distribution for the array. In any group of antennas, the mutual coupling between elements through the radiated field represents one of the biggest problems that the engineer faces and its effects are detrimental to the overall performance of the system, both in radiation capabilities and return loss. The employment of an equivalent circuit for the array design was discarded by some authors because of the difficulty involved in the characterization of the coupling effects and their inclusion in the design stage. In this thesis the coupling has also been modeled as an equivalent network whose elements are ideal transformers and admittances connected to the set of equivalent networks that represent the antennas of the array. By comparing the estimated results in terms of return loss and radiation with those obtained from popular commercial software as CST Microwave Studio, the validity of the proposed method is fully confirmed, representing the first method of systematic design of compound-slot arrays fed by rectangular waveguide. Since these slots do not work under the resonant status, the bandwidth in return loss is much wider than the longitudinal-slot arrays. For the case of two-dimensional arrays, the angle of inclination can be adjusted so that the field is polarized at the low side-lobe level plane. Besides the performed full-wave simulations two prototypes of six and ten elements for the X-band have been designed, built and measured, revealing excellent results and agreement with the expected results. These facts certify that the genuine technique Method of Moments - Matching Forward Procedure developed along this thesis is valid and trustable.

Propagation mechanism modelling in the near region of circular tunnels

Artículo sobre comunicaciones ferroviarias. Abstract: Along with the increase in operating frequencies in advanced radio communication systems utilised inside tunnels, the location of the break point is further and further away from the transmitter. This means that the near region lengthens considerably and even occupies the whole propagation cell or the entire length of some short tunnels. To begin with, this study analyses the propagation loss resulting from the free-space mechanism and the multi-mode waveguide mechanism in the near region of circular tunnels, respectively. Then, by conjunctive employing the propagation theory and the three-dimensional solid geometry, a general analytical model of the dividing point between two propagation mechanisms is presented for the first time. Moreover, the model is validated by a wide range of measurement campaigns in different tunnels at different frequencies. Finally, discussions on the simplified formulae of the dividing point in some application situations are made. The results in this study can be helpful to grasp the essence of the propagation mechanism inside tunnels.

Propagation Mechanism modeling in the Near-Region of Arbitrary Cross-Sectional Tunnels.

Along with the increase of the use of working frequencies in advanced radio communication systems, the near-region inside tunnels lengthens considerably and even occupies the whole propagation cell or the entire length of some short tunnels. This paper analytically models the propagation mechanisms and their dividing point in the near-region of arbitrary cross-sectional tunnels for the first time. To begin with, the propagation losses owing to the free space mechanism and the multimode waveguide mechanism are modeled, respectively. Then, by conjunctively employing the propagation theory and the three-dimensional solid geometry, the paper presents a general model for the dividing point between two propagation mechanisms. It is worthy to mention that this model can be applied in arbitrary cross-sectional tunnels. Furthermore, the general dividing point model is specified in rectangular, circular, and arched tunnels, respectively. Five groups of measurements are used to justify the model in different tunnels at different frequencies. Finally, in order to facilitate the use of the model, simplified analytical solutions for the dividing point in five specific application situations are derived. The results in this paper could help deepen the insight into the propagation mechanisms in tunnels.

EBG size reduction for low permittivity substrates

Double layer and edge-location via techniques are combined for electromagnetic band gap (EBG) size reduction. The study of the required number of elements and their dimensions is carried out in order to suppress the surface wave propagation modes and consequently to reduce the mutual coupling between radiating elements in low-permittivity substrates. By applying these techniques, the size of the EBG mushroom is reduced by 30%; however, the bandwidth operation maintains its value, and these structures can be integrated between radiating elements in broad bandwidth antennas.

Methods for noise reduction in far-field patterns obtained from cylindrical near-field antenna measurements

Two different methods to reduce the noise power in the far-field pattern of an antenna as measured in cylindrical near-field (CNF) are proposed. Both methods are based on the same principle: the data recorded in the CNF measurement, assumed to be corrupted by white Gaussian and space-stationary noise, are transformed into a new domain where it is possible to filter out a portion of noise. Those filtered data are then used to calculate a far-field pattern with less noise power than that one obtained from the measured data without applying any filtering. Statistical analyses are carried out to deduce the expressions of the signal-to-noise ratio improvement achieved with each method. Although the idea of the two alternatives is the same, there are important differences between them. The first one applies a modal filtering, requires an oversampling and improves the far-field pattern in all directions. The second method employs a spatial filtering on the antenna plane, does not require oversampling and the far-field pattern is only improved in the forward hemisphere. Several examples are presented using both simulated and measured near-field data to verify the effectiveness of the methods.

Calibration proposal for new antenna array architectures and technologies for space communications

In large antenna arrays with a large number of antenna elements, the required number of measurements for the characterization of the antenna array is very demanding in cost and time. This letter presents a new offline calibration process for active antenna arrays that reduces the number of measurements by subarray-level characterization. This letter embraces measurements, characterization, and calibration as a global procedure assessing about the most adequate calibration technique and computing of compensation matrices. The procedure has been fully validated with measurements of a 45-element triangular panel array designed for Low Earth Orbit (LEO) satellite tracking that compensates the degradation due to gain and phase imbalances and mutual coupling.