Simulating potential growth and yield of oil palm (Elaeis guineensis) with PALMSIM: Model description, evaluation and application.

Reducing the gap between water-limited potential yield and actual yield in oil palm production systems through intensification is seen as an important option for sustainably increasing palm oil production. Simulation models can play an important role in quantifying water-limited potential yield, and therefore the scope for intensification, but no oil palm model exists that is both simple enough and at the same time incorporates sufficient plant physiological knowledge to be generally applicable across sites with different growing conditions. The objectives of this study therefore were to develop a model (PALMSIM) that simulates, on a monthly time step, the potential growth of oil palm as determined by solar radiation and to evaluate model performance against measured oil palm yields under optimal water and nutrient management for a range of sites across Indonesia and Malaysia. The maximum observed yield in the field matches the corresponding simulated yield for dry bunch weight with a RMSE of 1.7 Mg ha?1 year?1 against an observed yield of 18.8 Mg ha?1. Sensitivity analysis showed that PALMSIM is robust: simulated changes in yield caused by modifying the parameters by 10% are comparable to other tree crop model evaluations. While we acknowledge that, depending on the soils and climatic environment, yields may be often water limited, we suggest a relatively simple physiological approach to simulate potential yield, which can be usefully applied to high rainfall environments and is considered as a first step in developing an oil palm model that also simulates water-limited potential yield. To illustrate the application possibil- ities of the model, PALMSIM was used to create a potential yield map for Indonesia and Malaysia by sim- ulating the growth and yield at a resolution of 0.1?. This map of potential yield is considered as a first step towards a decision support tool that can identify potentially productive, but at the moment degraded sites in Indonesia and Malaysia. ?

The Spreading of Christianity and the introduction of Modern Architecture in Shannxi, China (1840-1949): Christian churches and traditional Chinese architecture

La arquitectura china ha experimentado grandes cambios a lo largo de un extenso proceso histórico. El hito de mayor importancia es el que da paso al denominado Tiempo Moderno, periodo en el cual irrumpe por vez primera en China la arquitectura occidental, que comienza a tener una influencia muy activa y significativa sobre los rasgos y la identidad de la arquitectura tradicional china, hasta ese momento el único estilo o forma de hacer –muy diferente, en cuanto a su concepción y fisonomía, de los planteamientos occidentales- que había sobrevivido sin desvíos significativos, configurando un panorama milenario bastante homogéneo en los aspectos técnicos y artísticos en el desarrollo de esa arquitectura. Por un cúmulo de complejas razones, la mayor parte de la arquitectura china del periodo feudal -es decir el que forman todos los años anteriores a 1849- ha desaparecido. Sin embargo, desde la fecha indicada hasta la Revolución de 1949 (el denominado periodo semicolonial o semifeudal), sí se conservan muchas edificaciones, que fueron mejor construidas y mantenidas luego, destacando por su importancia en ese sentido las iglesias cristianas. Dichos templos representan cronológicamente, no sólo la primera irrupción de la arquitectura clásica occidental en China, sino el inicio de un proceso de modernización de la profundamente enraizada y, en buena medida, estancada arquitectura vernácula, combinando técnicas y estilos de ambos planteamientos, para dar como resultado originales edificaciones de un singular eclecticismo que caracterizarían buena parte de la arquitectura de dicha etapa semicolonial. En términos generales, últimamente se ha ido prestando cada vez más atención a esta arquitectura de los tiempos modernos, aunque las iglesias cristianas de la provincia de Shaanxi no han sido objeto de estudio específico, a pesar de que su tipología es muy representativa de las construcciones de esta clase en otras regiones del interior de China. La investigación que desarrolla la presente tesis doctoral sale al paso de esa deficiencia, abriendo puertas a la continuación del trabajo referido, extendido a otras zonas o arquitecturas, y, por extensión, a la profundización analítica de la hibridación arquitectónica y cultural entre China y Occidente. Sobre las bases de investigación documental, estudios de campo y dibujo, la tesis plantea un estudio aclaratorio de los rasgos y raíces de la arquitectura tradicional china, al que sigue otro histórico y tipológico de los templos cristianos en la provincia de Shaanxi, deteniéndose en sus características fundamentales, situación (uso) actual y estado de conservación. Se ha considerado imprescindible añadir al trabajo, como apéndice, un elaborado glosario conceptual ilustrado de términos básicos arquitectónicos y constructivos, en chino, inglés y español. ABSTRACT The Chinese architecture has gone through great changes during the long process of history. The tremendous changing period was the named Modern Times of China when, for the very first time, the western architecture was introduced into China and became to influence majorly on the traditional Chinese architecture. Before that, the traditional Chinese architecture which has its own, yet totally different system from the occidental architecture system was the only architectural style could be found in China. Although, due to many historical, conceptual and architectural characteristic reasons, large amount of the ancient Chinese architecture built in the feudal China was not preserved, there are a lot of buildings of semi-feudal China that was well constructed and conserved. The most important architectural type of the semi-feudal China is the Christian Churches. It was not only the first western architectural form that was brought into and well developed in China, but also was the beginner of the modernization process of Chinese architecture. Because of the deep root of the 2000-year traditional Chinese architecture, all the Christian Churches built in China during the semi-colonial society has a combined style of both the traditional Chinese architecture and the classic western churches. They are a priceless asset of the Chinese architectural history. Recently, more and more attention had been paid on the Chinese Modern Times architecture, however, the Christian Churches in Shaanxi Province, the province which has a unique history with the Christian, but less economically developed have never been researched yet. The Christian Churches of Shaanxi Province reflect the general feature of developing history of the Christian Churches of common inner-land regions in China. The research opens the door to further study on other Christian Churches and related buildings, and also for the further study on the Chinese-western architectural and culture communication. On the base of document research, field survey and mapping, in this thesis, an in-depth study had been done on the general history of the features and roots of the traditional Chinese architecture, the developing history of the Christian Churches of Shaanxi Province and the architectural types, examples, characteristics, present situation and conservation status. By comparing the Christian Churches of the cities in Shaanxi province to the Christian Churches in other more developed cities, and by comparing the Christian Churches in China to the classic western churches, the architectural combination feature of the Christian Churches in China are highlighted. The thesis is a fundamental research on which many further studies about the architectural developing history, characteristics and conservation of the Christian Churches in China could be done. It is considered essential to add to the work, as an appendix, an elaborate conceptual illustrated glossary of architectural and construction terms in Chinese, English and Spanish.

Towards downscaling of aerosol gridded dataset for improving solar resource assessment, an application to Spain

Solar radiation estimates with clear sky models require estimations of aerosol data. The low spatial resolution of current aerosol datasets, with their remarkable drift from measured data, poses a problem in solar resource estimation. This paper proposes a new downscaling methodology by combining support vector machines for regression (SVR) and kriging with external drift, with data from the MACC reanalysis datasets and temperature and rainfall measurements from 213 meteorological stations in continental Spain. The SVR technique was proven efficient in aerosol variable modeling. The Linke turbidity factor (TL) and the aerosol optical depth at 550 nm (AOD 550) estimated with SVR generated significantly lower errors in AERONET positions than MACC reanalysis estimates. The TL was estimated with relative mean absolute error (rMAE) of 10.2% (compared with AERONET), against the MACC rMAE of 18.5%. A similar behavior was seen with AOD 550, estimated with rMAE of 8.6% (compared with AERONET), against the MACC rMAE of 65.6%. Kriging using MACC data as an external drift was found useful in generating high resolution maps (0.05° × 0.05°) of both aerosol variables. We created high resolution maps of aerosol variables in continental Spain for the year 2008. The proposed methodology was proven to be a valuable tool to create high resolution maps of aerosol variables (TL and AOD 550). This methodology shows meaningful improvements when compared with estimated available databases and therefore, leads to more accurate solar resource estimations. This methodology could also be applied to the prediction of other atmospheric variables, whose datasets are of low resolution.

Towards cost reduction in concentrating solar power: innovative design for an efficient fresnel based solar field

Energía termosolar (de concentración) es uno de los nombres que hacen referencia en español al término inglés “concentrating solar power”. Se trata de una tecnología basada en la captura de la potencia térmica de la radiación solar, de forma que permita alcanzar temperaturas capaces de alimentar un ciclo termodinámico convencional (o avanzado); el futuro de esta tecnología depende principalmente de su capacidad para concentrar la radiación solar de manera eficiente y económica. La presente tesis está orientada hacia la resolución de ciertos problemas importantes relacionados con este objetivo. La mencionada necesidad de reducir costes en la concentración de radiación solar directa, asegurando el objetivo termodinámico de calentar un fluido hasta una determinada temperatura, es de vital importancia. Los colectores lineales Fresnel han sido identificados en la literatura científica como una tecnología con gran potencial para alcanzar esta reducción de costes. Dicha tecnología ha sido seleccionada por numerosas razones, entre las que destacan su gran libertad de diseño y su actual estado inmaduro. Con el objetivo de responder a este desafío se desarrollado un detallado estudio de las propiedades ópticas de los colectores lineales Fresnel, para lo cual se han utilizado métodos analíticos y numéricos de manera combinada. En primer lugar, se han usado unos modelos para la predicción de la localización y la irradiación normal directa del sol junto a unas relaciones analíticas desarrolladas para estudiar el efecto de múltiples variables de diseño en la energía incidente sobre los espejos. Del mismo modo, se han obtenido analíticamente los errores debidos al llamado “off-axis aberration”, a la apertura de los rayos reflejados en los espejos y a las sombras y bloqueos entre espejos. Esto ha permitido la comparación de diferentes formas de espejo –planos, circulares o parabólicos–, así como el diseño preliminar de la localización y anchura de los espejos y receptor sin necesidad de costosos métodos numéricos. En segundo lugar, se ha desarrollado un modelo de trazado de rayos de Monte Carlo con el objetivo de comprobar la validez del estudio analítico, pero sobre todo porque este no es preciso en el estudio de la reflexión en espejos. El código desarrollado está específicamente ideado para colectores lineales Fresnel, lo que ha permitido la reducción del tiempo de cálculo en varios órdenes de magnitud en comparación con un programa comercial más general. Esto justifica el desarrollo de un nuevo código en lugar de la compra de una licencia de otro programa. El modelo ha sido usado primeramente para comparar la intensidad de flujo térmico y rendimiento de colectores Fresnel, con y sin reflector secundario, con los colectores cilíndrico parabólicos. Finalmente, la conjunción de los resultados obtenidos en el estudio analítico con el programa numérico ha sido usada para optimizar el campo solar para diferentes orientaciones –Norte-Sur y Este-Oeste–, diferentes localizaciones –Almería y Aswan–, diferentes inclinaciones hacia el Trópico –desde 0 deg hasta 32 deg– y diferentes mínimos de intensidad del flujo en el centro del receptor –10 kW/m2 y 25 kW/m2–. La presente tesis ha conducido a importantes descubrimientos que deben ser considerados a la hora de diseñar un campo solar Fresnel. En primer lugar, los espejos utilizados no deben ser plano, sino cilíndricos o parabólicos, ya que los espejos curvos implican mayores concentraciones y rendimiento. Por otro lado, se ha llegado a la conclusión de que la orientación Este-Oeste es más propicia para localizaciones con altas latitudes, como Almería, mientras que en zonas más cercanas a los trópicos como Aswan los campos Norte-Sur conducen a mayores rendimientos. Es de destacar que la orientación Este-Oeste requiere aproximadamente la mitad de espejos que los campos Norte-Sur, puediendo estar inclinados hacia los Trópicos para mejorar el rendimiento, y que alcanzan parecidos valores de intensidad térmica en el receptor todos los días a mediodía. Sin embargo, los campos con orientación Norte-Sur permiten un flujo más constante a lo largo de un día. Por último, ha sido demostrado que el uso de diseños pre-optimizados analíticamente, con anchura de espejos y espaciado entre espejos variables a lo ancho del campo, pueden implicar aumentos de la energía generada por metro cuadrado de espejos de hasta el 6%. El rendimiento óptico anual de los colectores cilíndrico parabólicos es 23 % mayor que el rendimiento de los campos Fresnel en Almería, mientras que la diferencia es de solo 9 % en Aswan. Ello implica que, para alcanzar el mismo precio de electricidad que la tecnología de referencia, la reducción de costes de instalación por metro cuadrado de espejo debe estar entre el 10 % y el 25 %, y que los colectores lineales Fresnel tienen más posibilidades de ser desarrollados en zonas de bajas latitudes. Como consecuencia de los estudios desarrollados en esta tesis se ha patentado un sistema de almacenamiento que tiene en cuenta la variación del flujo térmico en el receptor a lo largo del día, especialmente para campos con orientación Este-Oeste. Este invento permitiría el aprovechamiento de la energía incidente durante más parte del año, aumentando de manera apreciable los rendimientos óptico y térmico. Abstract Concentrating solar power is the common name of a technology based on capturing the thermal power of solar radiation, in a suitable way to reach temperatures able to activate a conventional (or advanced) thermodynamic cycle to generate electricity; this quest mainly depends on our ability to concentrate solar radiation in a cheap and efficient way. The present thesis is focused to highlight and help solving some of the important issues related to this problem. The need of reducing costs in concentrating the direct solar radiation, but without jeopardizing the thermodynamic objective of heating a fluid up to the required temperature, is of prime importance. Linear Fresnel collectors have been identified in the scientific literature as a technology with high potential to reach this cost reduction. This technology has been selected because of a number of reasons, particularly the degrees of freedom of this type of concentrating configuration and its current immature state. In order to respond to this challenge, a very detailed exercise has been carried out on the optical properties of linear Fresnel collectors. This has been done combining analytic and numerical methods. First, the effect of the design variables on the ratio of energy impinging onto the reflecting surface has been studied using analytically developed equations, together with models that predict the location and direct normal irradiance of the sun at any moment. Similarly, errors due to off-axis aberration, to the aperture of the reflected energy beam and to shading and blocking effects have been obtained analytically. This has allowed the comparison of different shapes of mirrors –flat, cylindrical or parabolic–, as well as a preliminary optimization of the location and width of mirrors and receiver with no need of time-consuming numerical models. Second, in order to prove the validity of the analytic results, but also due to the fact that the study of the reflection process is not precise enough when using analytic equations, a Monte Carlo Ray Trace model has been developed. The developed code is designed specifically for linear Fresnel collectors, which has reduced the computing time by several orders of magnitude compared to a wider commercial software. This justifies the development of the new code. The model has been first used to compare radiation flux intensities and efficiencies of linear Fresnel collectors, both multitube receiver and secondary reflector receiver technologies, with parabolic trough collectors. Finally, the results obtained in the analytic study together with the numeric model have used in order to optimize the solar field for different orientations –North-South and East-West–, different locations –Almería and Aswan–, different tilts of the field towards the Tropic –from 0 deg to 32 deg– and different flux intensity minimum requirements –10 kW/m2 and 25 kW/m2. This thesis work has led to several important findings that should be considered in the design of Fresnel solar fields. First, flat mirrors should not be used in any case, as cylindrical and parabolic mirrors lead to higher flux intensities and efficiencies. Second, it has been concluded that, in locations relatively far from the Tropics such as Almería, East-West embodiments are more efficient, while in Aswan North- South orientation leads to a higher annual efficiency. It must be noted that East-West oriented solar fields require approximately half the number of mirrors than NS oriented fields, can be tilted towards the Equator in order to increase the efficiency and attain similar values of flux intensity at the receiver every day at midday. On the other hand, in NS embodiments the flux intensity is more even during each single day. Finally, it has been proved that the use of analytic designs with variable shift between mirrors and variable width of mirrors across the field can lead to improvements in the electricity generated per reflecting surface square meter up to 6%. The annual optical efficiency of parabolic troughs has been found to be 23% higher than the efficiency of Fresnel fields in Almería, but it is only around 9% higher in Aswan. This implies that, in order to attain the same levelized cost of electricity than parabolic troughs, the required reduction of installation costs per mirror square meter is in the range of 10-25%. Also, it is concluded that linear Fresnel collectors are more suitable for low latitude areas. As a consequence of the studies carried out in this thesis, an innovative storage system has been patented. This system takes into account the variation of the flux intensity along the day, especially for East-West oriented solar fields. As a result, the invention would allow to exploit the impinging radiation along longer time every day, increasing appreciably the optical and thermal efficiencies.

Reason and Being of Engineering Geology

This paper demonstrates the importance of a holistic comprehension of the Earth like a planet that is alive, not only in its Biosphere, looking at the atmosphere-ocean-crust-mantle interactions as its different sectorial expressions (climate, fluid-dynamics, morpho-dynamics, tectonics…) following the solar radiation and nuclear geothermal sources of energy. It considers the environmental incidence of different engineering activities to realize their underfeeding as the raison, and leads to that holistic formation as the being of the engineering geology

Study of PM10 and PM2.5 levels in three European cities: Analysis of intra and inter urban variations

In the present paper, 1-year PM10 and PM 2.5 data from roadside and urban background monitoring stations in Athens (Greece), Madrid (Spain) and London (UK) are analysed in relation to other air pollutants (NO,NO2,NOx,CO,O3 and SO2)and several meteorological parameters (wind velocity, temperature, relative humidity, precipitation, solar radiation and atmospheric pressure), in order to investigate the sources and factors affecting particulate pollution in large European cities. Principal component and regression analyses are therefore used to quantify the contribution of both combustion and non-combustion sources to the PM10 and PM 2.5 levels observed. The analysis reveals that the EU legislated PM 10 and PM2.5 limit values are frequently breached, forming a potential public health hazard in the areas studied. The seasonal variability patterns of particulates varies among cities and sites, with Athens and Madrid presenting higher PM10 concentrations during the warm period and suggesting the larger relative contribution of secondary and natural particles during hot and dry days. It is estimated that the contribution of non-combustion sources varies substantially among cities, sites and seasons and ranges between 38-67% and 40-62% in London, 26-50% and 20-62% in Athens, and 31-58% and 33-68% in Madrid, for both PM10 and PM 2.5. Higher contributions from non-combustion sources are found at urban background sites in all three cities, whereas in the traffic sites the seasonal differences are smaller. In addition, the non-combustion fraction of both particle metrics is higher during the warm season at all sites. On the whole, the analysis provides evidence of the substantial impact of non-combustion sources on local air quality in all three cities. While vehicular exhaust emissions carry a large part of the risk posed on human health by particle exposure, it is most likely that mitigation measures designed for their reduction will have a major effect only at traffic sites and additional measures will be necessary for the control of background levels. However, efforts in mitigation strategies should always focus on optimal health effects.

Cooperative ITS communications architecture: the FOTsis project approach and beyond

With the continuous development in the fields of sensors, advanced data processing and communications, road transport oriented intelligent applications and services have reached a significant maturity and complexity. Cooperative ITS services, based on the idea of sharing accurate information among road entities, are currently being tested on a large scale by different initiatives. The field operational test (FOTsis) project contributes to the deployment environment with services that involve a significant number of entities out of the vehicle. This made necessary the specification of an architecture which, based on the ISO ITS station reference architecture for communications, could support the requirements of the services proposed in the project. During the project, internal implementation tests and external interoperability tests have resulted in the validation of the proposed architecture. At the same time, these tests have had as a result the awareness of areas in which the FOTsis architecture could be completed, mainly to take full advantage of all the emerging and foreseeable data sources which may be relevant in the road environment. In this study, the authors will outline an approach that, based on the current cooperative ITS architecture and the SmartCities and Internet Of Things (IoT) architectures, can provide a common convergence platform to maximise the information available for ITS purposes.

3-D modeling of perimeter recombination in GaAs diodes and its influence on concentrator solar cells

This paper describes a complete modelling of the perimeter recombination of GaAs diodes which solves most unknowns and suppresses the limitations of previous models. Because of the three dimensional nature of the implemented model, it is able to simulate real devices. GaAs diodes on two epiwafers with different base doping levels, sizes and geometries, namely square and circular are manufactured. The validation of the model is achieved by fitting the experimental measurements of the dark IV curve of the manufactured GaAs diodes. A comprehensive 3-D description of the occurring phenomena affecting the perimeter recombination is supplied with the help of the model. Finally, the model is applied to concentrator GaAs solar cells to assess the impact of their doping level, size and geometry on the perimeter recombination.

Feo, inútil, inestable: pensamiento crítico contemporáneo y procesos proyectivos en arquitectura = Ugly, useless, unstable: contemporary critical thought and projective processes in architecture

La presente tesis doctoral persigue dos objetivos simultáneos: Determinar el alcance de los criterios clásicos para la evaluación de arquitectura y poner en crisis la prevalencia de esos mismos criterios dentro del marco crítico y productivo actual. En concreto, esta tesis se interroga sobre la posible contribución de determinadas corrientes del pensamiento post-estructuralista y neo-materialista a las tareas de expansión y transformación de los criterios clásicos antes mencionados. Asimismo, se plantea la oportunidad de formalizar estas incorporaciones conceptuales como metodologías para el proyectar arquitectónico. La tesis emplea un análisis pormenorizado de las cualidades implícitas en la triada Firmitas, Utilitas, Venustas elaborada por Vitruvio como vehículo para calibrar la influencia de los paradigmas de pensamiento clásico en nuestras posiciones críticas contemporáneas. Como reacción al carácter dominante de dichos paradigmas, y con la ayuda de una compilación selectiva de ejemplos procedentes de los campos artístico y arquitectónico, la presente tesis procede a examinar y clasificar diversas estrategias arquitectónicas basadas en la no conformidad con los criterios clásicos de evaluación de la disciplina. A la hora de realizar esta tarea, y con el objetivo de superar el dualismo trascendental que caracteriza la gran mayoría de dichos criterios clásicos, se propone un modelo analítico y multidimensional que formula las instancias arquitectónicas como posibles posiciones dentro de un extenso continuo combinatorio de cualidades formales, estructurales y organizativas. Este modelo conceptual permite replantear el aparente antagonismo entre los principios de Vitruvio y sus opuestos, estableciendo en su lugar un dominio operativo continuo de producción arquitectónica. Esta operación abre una ventana de oportunidad para expandir los límites del marco crítico actual más allá de las fronteras establecidas por nuestra herencia clásica. En consecuencia con esta voluntad, la presente tesis pretende habilitar un ámbito para el análisis crítico de las estrategias que caracterizan ciertas corrientes del proyectar contemporáneo, pero también contribuir a informar nuevas aproximaciones metodológicas al proceso de proyecto, desplazando progresivamente su foco desde lo descriptivo hacia lo proyectivo. ABSTRACT This doctoral thesis attempts to simultaneously determine the scope of the classical criteria for the evaluation of architecture and challenge their prevalence within the current framework of architectural production and criticism. It examines how specific strands of post-structuralism and neo-materialism may contribute to both the expansion and the transformation of these criteria and, in doing so, sets itself the goal of mobilising these conceptual incorporations as explicit design methodologies. A detailed analysis of the formal, structural and organisational qualities implicit in Vitruvius’ triad Firmitas, Utilitas, Venustas is used as a starting point to determine the influence of classical paradigms in our current critical positions. As a reaction to this critical pervasiveness, and supported by a curated collection of artistic and architectural works, diverse approaches to non-compliance with the classical criteria of assessment are examined and classified. In order to facilitate this endeavour -and to overcome the transcendental dualism of most classical critical approaches in architecture- this thesis puts forward an analytical, multidimensional model that formulates architectural instances as possible positions within a larger combinatory continuum of formal, structural and organisational qualities. Using this conceptual model, the apparent antagonism between Vitruvius’ principles and its non-compliant opposites is reframed as a continuous operative domain of architectural production, which in turn opens up a window of opportunity to expand the limits of our critical framework beyond the boundaries of classical paradigms. In doing so, this thesis attempts not only to foster a better understanding of some of the strategic approaches that characterise contemporary systems of architectural production, but also to inform future methodological approaches to architectural design, hence situating itself beyond the domain of the descriptive and moving towards the projective.

Analytical study of the thermal behaviour and stability of a small satellite

In this work the thermal analysis of a small satellite orbiting around the Earth has been approached by direct integration of the heat balance equations of a two-node reduced model, obtaining a linearized second order ODE problem, similar in form to the classical case of the forced vibration of a damped system. As the thermal loads (solar radiation, albedo, etc.) are harmonic, the problem is solved by means of Fourier analysis methods. Research on that field can be directly applied to the analysis of thermal problems and the results obtained are satisfactory. Working on the frequency domain streamlines the analysis, simplifies the study and facilitates the experimental testing. The transfer functions are obtained for the two-node case but the study can be extended to an n-node model.

La implementación arquitectónica de los acristalamientos activos con agua circulante, y su contribución en edificios de consumo de energía casi nulo

La presente Tesis Doctoral evalúa la contribución de una fachada activa, constituida por acristalamientos con circulación de agua, en el rendimiento energético del edificio. Con especial énfasis en la baja afección sobre su imagen, su integración ha de favorecer la calificación del edificio con el futuro estándar de Edificio de consumo de Energía Casi Nulo (EECN). El propósito consiste en cuantificar su aportación a limitar la demanda de climatización, como solución de fachada transparente acorde a las normas de la energía del 2020. En el primer capítulo se introduce el planteamiento del problema. En el segundo capítulo se desarrollan la hipótesis y el objetivo fundamental de la investigación. Para tal fin, en el tercer capítulo, se revisa el estado del arte de la tecnología y de la investigación científica, mediante el análisis de la literatura de referencia. Se comparan patentes, prototipos, sistemas comerciales asimilables, investigaciones en curso en Universidades, y proyectos de investigación y desarrollo, sobre envolventes que incorporan acristalamientos con circulación de agua. El método experimental, expuesto en el cuarto capítulo, acomete el diseño, la fabricación y la monitorización de un prototipo expuesto, durante ciclos de ensayos, a las condiciones climáticas de Madrid. Esta fase ha permitido adquirir información precisa sobre el rendimiento del acristalamiento en cada orientación de incidencia solar, en las distintas estaciones del año. En paralelo, se aborda el desarrollo de modelos teóricos que, mediante su asimilación a soluciones multicapa caracterizadas en las herramientas de simulación EnergyPlus y IDA-ICE (IDA Indoor Climate and Energy), reproducen el efecto experimental. En el quinto capítulo se discuten los resultados experimentales y teóricos, y se analiza la respuesta del acristalamiento asociado a un determinado volumen y temperatura del agua. Se calcula la eficiencia en la captación de la radiación y, mediante la comparativa con un acristalamiento convencional, se determina la reducción de las ganancias solares y las pérdidas de energía. Se comparan el rendimiento del acristalamiento, obtenido experimentalmente, con el ofrecido por paneles solares fototérmicos disponibles en el mercado. Mediante la traslación de los resultados experimentales a casos de células de tamaño habitable, se cuantifica la afección del acristalamiento sobre el consumo en refrigeración y calefacción. Diferenciando cada caso por su composición constructiva y orientación, se extraen conclusiones sobre la reducción del gasto en climatización, en condiciones de bienestar. Posteriormente, se evalúa el ahorro de su incorporación en un recinto existente, de construcción ligera, localizado en la Escuela de Arquitectura de la Universidad Politécnica de Madrid (UPM). Mediante el planteamiento de escenarios de rehabilitación energética, se estima su compatibilidad con un sistema de climatización mediante bomba de calor y extracción geotérmica. Se describe el funcionamiento del sistema, desde la perspectiva de la operación conjunta de los acristalamientos activos e intercambio geotérmico, en nuestro clima. Mediante la parametrización de sus funciones, se estima el beneficio adicional de su integración, a partir de la mejora del rendimiento de la bomba de calor COP (Coefficient of Performance) en calefacción, y de la eficiencia EER (Energy Efficiency Ratio) en refrigeración. En el recinto de la ETSAM, se ha analizado la contribución de la fachada activa en su calificación como Edificio de Energía Casi Nula, y estudiado la rentabilidad económica del sistema. En el sexto capítulo se exponen las conclusiones de la investigación. A la fecha, el sistema supone alta inversión inicial, no obstante, genera elevada eficiencia con bajo impacto arquitectónico, reduciéndose los costes operativos, y el dimensionado de los sistemas de producción, de mayor afección sobre el edificio. Mediante la envolvente activa con suministro geotérmico no se condena la superficie de cubierta, no se ocupa volumen útil por la presencia de equipos emisores, y no se reduce la superficie o altura útil a base de reforzar los aislamientos. Tras su discusión, se considera una alternativa de valor en procesos de diseño y construcción de Edificios de Energía Casi Nulo. Se proponen líneas de futuras investigación cuyo propósito sea el conocimiento de la tecnología de los acristalamientos activos. En el último capítulo se presentan las actividades de difusión de la investigación. Adicionalmente se ha proporcionado una mejora tecnológica a las fachadas activas existentes, que ha derivado en la solicitud de una patente, actualmente en tramitación. ABSTRACT This Thesis evaluates the contribution of an active water flow glazing façade on the energy performance of buildings. Special emphasis is made on the low visual impact on its image, and the active glazing implementation has to encourage the qualification of the building with the future standard of Nearly Zero Energy Building (nZEB). The purpose is to quantify the façade system contribution to limit air conditioning demand, resulting in a transparent façade solution according to the 2020 energy legislation. An initial approach to the problem is presented in first chapter. The second chapter develops the hypothesis and the main objective of the research. To achieve this purpose, the third chapter reviews the state of the art of the technology and scientific research, through the analysis of reference literature. Patents, prototypes, assimilable commercial systems, ongoing research in other universities, and finally research and development projects incorporating active fluid flow glazing are compared. The experimental method, presented in fourth chapter, undertakes the design, manufacture and monitoring of a water flow glazing prototype exposed during test cycles to weather conditions in Madrid. This phase allowed the acquisition of accurate information on the performance of water flow glazing on each orientation of solar incidence, during different seasons. In parallel, the development of theoretical models is addressed which, through the assimilation to multilayer solutions characterized in the simulation tools EnergyPlus and IDA-Indoor Climate and Energy, reproduce the experimental effect. Fifth chapter discusses experimental and theoretical results focused to the analysis of the active glazing behavior, associated with a specific volume and water flow temperature. The efficiency on harvesting incident solar radiation is calculated, and, by comparison with a conventional glazing, the reduction of solar gains and energy losses are determined. The experimental performance of fluid flow glazing against the one offered by photothermal solar panels available on the market are compared. By translating the experimental and theoretical results to cases of full-size cells, the reduction in cooling and heating consumption achieved by active fluid glazing is quantified. The reduction of energy costs to achieve comfort conditions is calculated, differentiating each case by its whole construction composition and orientation. Subsequently, the saving of the implementation of the system on an existing lightweight construction enclosure, located in the School of Architecture at the Polytechnic University of Madrid (UPM), is then calculated. The compatibility between the active fluid flow glazing and a heat pump with geothermal heat supply system is estimated through the approach of different energy renovation scenarios. The overall system operation is described, from the perspective of active glazing and geothermal heat exchange combined operation, in our climate. By parameterization of its functions, the added benefit of its integration it is discussed, particularly from the improvement of the heat pump performance COP (Coefficient of Performance) in heating and efficiency EER (Energy Efficiency Ratio) in cooling. In the case study of the enclosure in the School of Architecture, the contribution of the active glazing façade in qualifying the enclosure as nearly Zero Energy Building has been analyzed, and the feasibility and profitability of the system are studied. The sixth chapter sets the conclusions of the investigation. To date, the system may require high initial investment; however, high efficiency with low architectural impact is generated. Operational costs are highly reduced as well as the size and complexity of the energy production systems, which normally have huge visual impact on buildings. By the active façade with geothermal supply, the deck area it is not condemned. Useful volume is not consumed by the presence of air-conditioning equipment. Useful surface and room height are not reduced by insulation reinforcement. After discussion, water flow glazing is considered a potential value alternative in nZEB design and construction processes. Finally, this chapter proposes future research lines aiming to increase the knowledge of active water flow glazing technology. The last chapter presents research dissemination activities. Additionally, a technological improvement to existing active facades has been developed, which has resulted in a patent application, currently in handling process.

Determinación y caracterización de los indicadores que intervienen en un sistema integral de iluminación natural y protección solar : aplicado a la incorporación de bandejas en los huecos de fachadas existentes

En esta tesis se estudia cómo lograr el equilibrio entre dos fenómenos naturales que afectan a los huecos de fachadas: la iluminación natural y la ganancia solar. Es decir, el cómo, conseguir la optimización de la iluminación natural que se introduce a través de las ventanas existentes, sin realizar una laboriosa intervención de sustitución de las mismas y el cómo, conseguir la protección de la radiación solar directa de la zona acristalada, para evitar tanto las ganancias térmicas innecesarias como el deslumbramiento que afecta a la calidad lumínica de los recintos. Para el desarrollo esta investigación se ha propuesto una metodología de estudio dividida en dos fases: La primera, de Análisis y Diagnóstico, en la que se han de definir los estándares a cumplir y las variables con las que se evaluarán las bandejas. Y, la segunda, de Evaluación y Comprobación en la que se han de establecer los criterios de valoración y ponderación de cada variable. En la primera fase, se definirán las variables físico-ambientales, para lo que se seleccionarán algunas ciudades a estudiar, a las cuales se les estudiará las necesidades de confort térmico, se determinarán las dimensiones que deben tener las protecciones solares en esas ciudades, además se determinarán las actuaciones a realizar en los huecos de fachada según sea su posición en el plano vertical de la misma. Así mismo, se plantea hacer un análisis de casos reales, para lo que se caracterizarán desde el punto de vista lumínico algunas viviendas, realizando medidas “in situ” y comparando resultados con los que se obtienen de los programas de simulación, para seleccionar las viviendas en las que la realidad y la simulación se aproximen más, una de estas viviendas servirá de modelo en las simulaciones que se realizará en la segunda fase. También, en esta primera fase, mediante un modelo neutro, se estudiará el comportamiento térmico y lumínico del tamaño del hueco en el que se insertará la bandeja posteriormente, para luego estudiar la posición de la bandeja en el plano vertical de la ventana, desde el punto de vista ergonómico. Y finalmente se estudiará, el comportamiento térmico y lumínico del modelo con la bandeja ubicada a 40, 50 y 60cm del techo. En la segunda fase, se establecerá la valoración y ponderación de las variables con las que seleccionar la bandeja que mejor equilibre los aspectos térmicos y lumínicos, teniendo en cuenta estrategias pasivas de acondicionamiento ambiental, como favorecer las ganancias solares en invierno en horas diurnas y evitar las pérdidas de calor en horas nocturnas; y en verano implementar sistemas de sombreamiento en la zona acristalada para evitar las ganancias de calor; y, tanto en verano como en invierno, aprovechar la iluminación natural, para favorecer la iluminancia útil y evitar el deslumbramiento. Una vez definidos los criterios de valoración y ponderación se aplicará a la evaluación térmica y lumínica del modelo neutro con la bandeja, consiguiendo seleccionar la bandeja con mejor comportamiento. Posteriormente se comprobará la metodología de estudio desarrollada en el modelo seleccionado, se evaluará el comportamiento térmico y lumínico, con la incorporación de algunas alternativas de bandeja. Con esta investigación se quiere demostrar que mediante la aplicación de esta metodología de estudio, es posible evaluar y seleccionar bandejas que respondan a las necesidades requeridas en distintos casos de estudio, por lo que se considera que, la bandeja puede ser un elemento arquitectónico aplicable tanto en rehabilitación como en nueva construcción, de espacios en los que sea necesario mejorar sus condiciones lumínicas y térmicas simultáneamente. ABSTRACT This thesis studies how to balance two natural events that affect the window opening of facades: daylighting and solar gain. That is to say, how to achieve optimization of natural light that gets in through the existing windows, without making a laborious intervention of replacing them and how to get protection from direct solar radiation from the glass area, to avoid unnecessary heat gain and glare affecting the light quality of the enclosures. To develop this research, it has been proposed a methodology of study divided into two phases: First phase, Analysis and Diagnostics, in which the variables with which the light shelf are evaluated will be defined along with the standards the light shelves will meet. The second phase, Assessment and Verification, in which the assessment criteria and weighting of each variable will be established. In the first phase, the physical and environmental variables shall be defined, various cities will be selected to be studied, and in each the needs of thermal comfort will be determined along with the dimensions of shading devices in the cities. In addition the actions to be taken in the window opening of the façade will be determined, depending on their position in the vertical plane. An analysis of real cases will be undertaken, which will be characterized from the luminous point of view, performing "in situ" measurements and comparing results with those obtained from simulation programs, to select places/dwellings where reality and simulation are closer, one of these places/dwellings will be a model, in the simulations to perform at the second phase. Also, in this first phase, by a neutral model, the thermal and light behavior of the size of the window opening will be studied, in which the light shelf is inserted later, the position of the light shelf in the vertical plane of the window is studied, from an ergonomic point of view. And finally to study the thermal and light behavior of the model with the light shelf located at 40, 50 and 60cm from the ceiling. In the second phase, the evaluation and weighting of the variables will be established selecting the light shelf that best balances the thermal and daylighting aspects, taking into account passive environmental conditioning strategies; such as getting solar gains in winter during daylight hours, and preventing heat loss during the night hours; and in summer implementing shading systems in the glazing area to avoid heat gains. And in both summer and winter, taking advantage of natural lighting, to improve useful illuminance and avoid glare. Once defined, the evaluation criteria and weighting will be applied to thermal and daylighting evaluation to the neutral model with the light shelf, the best performing light shelf will be selected. The study methodology developed in the selected model will be verified the thermal and daylighting performance with the addition of some light shelf alternative will also be studied. With this research, we want to show that by applying this study methodology it is possible to evaluate and select the light shelf that meets the needs required in different case studies, so it is considered that the light shelf may be an applicable architectural element in both refurbishment and new construction of spaces where necessary to improve their daylighting and thermal conditions simultaneously.

Improved modeling of photoluminescent and electroluminescent coupling in multijunction solar cells

The performance of tandem stacks of Group III?V multijunction solar cells continues to improve rapidly, both through improved performance of the individual cells in the stack and throughi ncrease in the number of stacked cells. As the radiative efficiency of these individual cells increases, radiative coupling between the stacked cells becomes an increasingly important factor not only in cell design, but also in accurate efficiency measurement and in determining performance of cells and systems under varying spectral conditions in the field. Past modeling has concentrated on electroluminescent coupling between the cells, although photoluminescent coupling is shown to be important for cells operating near their maximum power point voltage or below or when junction defect recombination is significant. Extension of earlier models i sproposed to allow this non-negligible component of luminescent coupling to be included. Therefined model is validated by measurement of the closely related external emission from both single and double junction cells.

Comparing the Luttinger–Kohn–Pikus–Bir and the Empiric K·P Hamiltonians in quantum dot intermediate band solar cells manufactured in zincblende semiconductors

The calculation of the energy spectrum and absorption coefficients of quantum dot nanostructured intermediate band solar cells using the Empiric K·P Hamiltonian method and its agreement with experimental data are summarized. The well established Luttinger Kohn Hamiltonian modified by Pikus and Bir for strained material, such as quantum dot arrays, is presented using a simplified strain field that allows for square band offsets. The energy spectrum and absorption coefficients are calculated with this new Hamiltonian. With the approximations made the energy spectrum results to be exactly the same but the absorption coefficient fits experiments less accurately. The computer time using the latter Hamiltonian is much longer than the former one.