Vortex-induced vibrations on bridges : the interaction mechanism in complex sections and a new proposed semi-empirical model

El presente trabajo de investigación se ocupa del estudio de las vibraciones verticales inducidas por vórtices (VIV) en aquellos puentes que, por sus características geométricas y propiedades dinámicas, muestran cierta sensibilidad este tipo de fenómeno aeroelástico. El objeto principal es el análisis del mecanismo de interacción viento-estructura sobre secciones no fuseladas de geometría simple, con objeto de realizar una adecuada caracterización del problema y poder abordar posteriormente el análisis de otras secciones de geometría más compleja, representativas de los principales elementos estructurales de los puentes, como arcos, tableros, torres y pilas. Este aspecto es fundamental durante la fase de diseño del puente, donde deberán tenerse en cuenta también una serie de detalles que pueden influir significativamente su sensibilidad ante problemas aerodinámicos, como la morfología y dimensiones principales de la sección transversal del tablero, la disposición de barreras de seguridad y barreras cortaviento, o las riostras que unen diferentes elementos estructurales. La configuración de dos elementos en tándem o la construcción de un puente en las inmediaciones de otro existente son otros aspectos a considerar respecto a la sensibilidad frente a efectos aeroelásticos. El estudio se ha llevado a cabo principalmente mediante la implementación de simulaciones numéricas que reproducen la interacción entre la corriente de aire y secciones representativas de modelos estructurales, a partir de un código CFD basado en el método de las partículas de vórtices (VPM), siguiendo por tanto un esquema Lagrangiano. Los resultados han sido validados con datos experimentales existentes, valores procedentes de ensayos en túnel de viento y registros reales a partir de diferentes casos de estudio: Alconétar (2006), Niterói (1980), Trans- Tokyo Bay (1995) y Volgogrado (2010). Finalmente, se propone un modelo semi-empírico para la estimación del rango de velocidades críticas y amplitudes de oscilación basado en la utilización de las derivadas de flameo de Scanlan, y la densidad espectral de las fuerzas aerodinámicas en el dominio de la frecuencia. The present research work concerns the study of vertical vortex-induced vibrations (VIV) in bridges which show certain sensitivity to this type of aeroelastic phenomenon. It focuses on the analysis of the wind-structure interaction mechanism on bluff sections, with the objective of making a good characterisation of the problem and subsequently addressing the analysis of sections with a complex geometry, which are representative of the bridge structural elements, such as arches, decks, towers and piers. This issue is of relative importance during the bridge design phase, since minor details of the aforementioned elements can significantly influence its sensitivity to aerodynamic problems. The shape and main dimensions of the deck cross section, the addition of safety barriers and windshields, the presence of braces to enhance the structure mechanical properties, the utilisation of cross sections in tandem arrangement, or the erection of a new bridge in the vicinity of another existing one are some of the aspects to be considered regarding the sensitivity to the aeroelastic effects. The study has been carried out mainly through the implementation of numerical simulations that reproduces the interaction between the airflow and the representative cross section of a structural bridge model, by the use of a CFD code based on the vortex particle method (VPM), thus following a Lagrangian scheme. The results have been validated with existing experimental data, values from wind tunnel tests and full scale observations from the different case studies: Alconétar (2006), Niterói (1980), Trans-Tokyo Bay (1995) and Volgograd (2010). Finally, a new semi-empirical model is proposed for the estimation of the critical wind velocity ranges and oscillation amplitudes based on the use of the Scanlan’s flutter derivatives and the power spectral density of aerodynamic force time history in the frequency domain.

Comportamiento de pilares de hormigón armado confinados con materiales compuestos sometidos a compresión centrada

En la actualidad muchas estructuras de hormigón armado necesitan ser reforzadas debido a diversas razones: errores en el proyecto o construcción, deterioro debido a efectos ambientales, cambios de uso o mayores requerimientos en los códigos. Los materiales compuestos, también conocidos como polímeros reforzados con fibras (FRP), están constituidos por fibras continuas de gran resistencia y rigidez embebidas en un material polimérico. Los FRP se utilizan cada vez más en aplicaciones estructurales debido a sus excelentes propiedades (elevadas resistencia y rigidez específicas y resistencia a la corrosión). Una de las aplicaciones más atractivas es el refuerzo de pilares mediante confinamiento para incrementar su resistencia y ductilidad. El confinamiento puede conseguirse pegando capas de FRP envolviendo el pilar en la dirección de los cercos (con las fibras orientadas en dirección perpendicular al eje del elemento). Se han realizado numerosos estudios experimentales en probetas cilíndricas pequeñas confinadas con encamisados de FRP y sometidas a compresión axial, y se han propuesto varios modelos sobre el hormigón confinado con FRP. Es sabido que el confinamiento de pilares de sección no circular es menos eficiente. En una sección circular, el FRP ejerce una presión de confinamiento uniforme sobre todo el perímetro, mientras que en una sección rectangular la acción de confinamiento se concentra en las esquinas. Esta tesis presenta los resultados de una investigación experimental sobre el comportamiento de probetas de hormigón de sección cuadrada confinadas con FRP y sometidas a compresión centrada. Se realizaron un total de 42 ensayos investigándose el comportamiento en las direcciones axial y transversal. Las variables del estudio incluyen: la resistencia del hormigón, el tipo de fibras (vidrio o carbono), la cuantía de refuerzo y el radio de curvatura de las esquinas. Los resultados de los ensayos realizados muestran que el confinamiento con FRP puede mejorar considerablemente la resistencia y ductilidad de pilares de hormigón armado de sección cuadrada con las esquinas redondeadas. La mejora conseguida es mayor en los hormigones de baja resistencia que en los de resistencia media. La deformación de rotura de la camisa de FRP es menor que la que se obtiene en ensayos de tracción normalizados del laminado, y la eficiencia del confinamiento depende en gran medida del radio de redondeo de las esquinas. Los resultados se han comparado con los obtenidos según los modelos teóricos más aceptados. Hay dos parámetros críticos en el ajuste de los modelos: el factor de eficiencia de la deformación y el efecto de confinamiento en secciones no circulares. Nowadays, many existing RC structures are in need of repair and strengthening for several reasons: design or construction errors, deterioration caused by environmental effects, change in use of the structures or revisions of code requirements. Composite materials, also known as fibre reinforced polymers (FRP), are composed of high strength and stiffness continuous fibres embedded in a polymer material. FRP materials are being increasingly used in many structural applications due to their excellent properties (high strength- and stiffness-toweight ratio, good corrosion behaviour). One of the most attractive applications of FRP is the confinement of concrete columns to enhance both strength and ductility. Concrete confinement can be achieved by bonding layers of hoop FRP around the column (fibres oriented perpendicular to the longitudinal axis). Many experimental studies have been conducted on small-scale plain concrete specimens of circular cross-sections confined with FRP and subjected to pure axial compressive loading, and several design models have been proposed to describe the behaviour of FRP-confined concrete. It is widely accepted that the confinement of non-circular columns is less efficient than the confinement of circular columns. In a circular cross section, the jacket exerts a uniform confining pressure over the entire perimeter. In the case of a rectangular cross section, the confining action is mostly concentrated at the corners. This thesis presents the results of a comprehensive experimental investigation on the behaviour of axially loaded square concrete specimens confined with FRP. A total of 42 compression tests were conducted, and the behaviour of the specimens in the axial and transverse directions were investigated. The parameters considered in this study are: concrete strength, type of fibres (glass or carbon), amount of FRP reinforcement and corner radius of the cross section. The tests results indicate that FRP confinement can enhance considerably the compressive strength and ductility of RC square columns with rounded corners. The enhancement is more pronounced for low- than for normal-strength concrete. The rupture strain of the FRP jacket is lower than the ultimate strain obtained by standard tensile testing of the FRP material, and the confinement efficiency significantly depends on the corner radius. The confined concrete behaviour was predicted according to the more accepted theoretical models and compared with experimental results. There are two key parameters which critically influence the fitting of the models: the strain efficiency factor and the effect of confinement in non-circular sections.

Radiative properties for warm and hot dense matter

We will present calculations of opacities for matter under LTE conditions. Opacities are needed in radiation transport codes to study processes like Inertial Confinement Fusion and plasma amplifiers in X-ray secondary sources. For the calculations we use the code BiGBART, with either a hydrogenic approximation with j-splitting or self-consistent data generated with the atomic physics code FAC. We calculate the atomic structure, oscillator strengths, radiative transition energies, including UTA computations, and photoionization cross-sections. A DCA model determines the configurations considered in the computation of the opacities. The opacities obtained with these two models are compared with experimental measurements.

Propagation of Nuclear Data Uncertainties in Transmutation Calculations Using ACAB Code

The assessment of the accuracy of parameters related to the reactor core performance (e.g., ke) and f el cycle (e.g., isotopic evolution/transmutation) due to the uncertainties in the basic nuclear data (ND) is a critical issue. Different error propagation techniques (adjoint/forward sensitivity analysis procedures and/or Monte Carlo technique) can be used to address by computational simulation the systematic propagation of uncertainties on the final parameters. To perform this uncertainty assessment, the ENDF covariance les (variance/correlation in energy and cross- reactions-isotopes correlations) are required. In this paper, we assess the impact of ND uncertainties on the isotopic prediction for a conceptual design of a modular European Facility for Industrial Transmutation (EFIT) for a discharge burnup of 150 GWd/tHM. The complete set of uncertainty data for cross sections (EAF2007/UN, SCALE6.0/COVA-44G), radioactive decay and fission yield data (JEFF-3.1.1) are processed and used in ACAB code.

Uncertainty methods inactivation and inventory calculations

For a number of important nuclides, complete activation data libraries with covariance data will be produced, so that uncertainty propagation in fuel cycle codes (in this case ACAB,FISPIN, ...) can be developed and tested. Eventually, fuel inventory codes should be able to handle the complete set of uncertainty data, i.e. those of nuclear reactions (cross sections, etc.), radioactive decay and fission yield data. For this, capabilities will be developed both to produce covariance data and to propagate the uncertainties through the inventory calculations.

A proposed parameterization of interface discontinuity factors depending on neighborhood for pin-by-pin diffusion computations for LWR

There exists an interest in performing full core pin-by-pin computations for present nuclear reactors. In such type of problems the use of a transport approximation like the diffusion equation requires the introduction of correction parameters. Interface discontinuity factors can improve the diffusion solution to nearly reproduce a transport solution. Nevertheless, calculating accurate pin-by-pin IDF requires the knowledge of the heterogeneous neutron flux distribution, which depends on the boundary conditions of the pin-cell as well as the local variables along the nuclear reactor operation. As a consequence, it is impractical to compute them for each possible configuration. An alternative to generate accurate pin-by-pin interface discontinuity factors is to calculate reference values using zero-net-current boundary conditions and to synthesize afterwards their dependencies on the main neighborhood variables. In such way the factors can be accurately computed during fine-mesh diffusion calculations by correcting the reference values as a function of the actual environment of the pin-cell in the core. In this paper we propose a parameterization of the pin-by-pin interface discontinuity factors allowing the implementation of a cross sections library able to treat the neighborhood effect. First results are presented for typical PWR configurations.

Kinetics of color center formation in silica irradiated with swift heavy ions: Thresholding and formation efficiency

We have determined the cross-section σ for color center generation under single Br ion impacts on amorphous SiO2. The evolution of the cross-sections, σ(E) and σ(Se), show an initial flat stage that we associate to atomic collision mechanisms. Above a certain threshold value (Se > 2 keV/nm), roughly coinciding with that reported for the onset of macroscopic disorder (compaction), σ shows a marked increase due to electronic processes. In this regime, a energetic cost of around 7.5 keV is necessary to create a non bridging oxygen hole center-E′ (NBOHC/E′) pair, whatever the input energy. The data appear consistent with a non-radiative decay of self-trapped excitons.

Nonlinear response to ultrasound of encapsulated microbubbles

The acoustic backscatter of encapsulated gas-filled microbubbles immersed in a weak compressible liquid and irradiated by ultrasound fields of moderate to high pressure amplitudes is investigated theoretically. The problem is formulated by considering, for the viscoelastic shell of finite thickness, an isotropic hyperelastic neo-Hookean model for the elastic contribution in addition to a Newtonian viscous component. First and second harmonic scattering cross-sections have been evaluated and the quantitative influence of the driving pressure amplitude on the harmonic resonance frequencies for different initial equilibrium bubble sizes and for different encapsulating physical properties has been determined. Conditions for optimal second harmonic imaging have been also investigated and some regions in the parameters space where the second harmonic intensity is dominant over the fundamental have been identified. Results have been obtained for albumin, lipid and polymer encapsulating shells, respectively.

Single - and double energy swift and slow heavy ion irradiated optical waveguides in Er: Tungstene-Tellurite glass and BGO for telecom applications

The fabrication of broadband amplifiers in wavelength division multiplexing (WDM) around 1.55 m, as they exhibit large stimulated cross sections and broad emission bandwidth. Bi4Ge3O12 (eultine type BGO) - well known scintillator material, also a rare-earth host material, photorefractive waveguides produced in it only using light ions in the past. Recently: MeV N+ ions and swift O5+ and C5+ ions, too*. Bi12GeO20 (sillenite type BGO) - high photoconductivity and photorefractive sensitivity in the visible and NIR good candidate for real-time holography and optical phase conjugation, photorefractive waveguides produced in it only using light ions. No previous attempts of ion beam fabrication of waveguides in it.

Análisis experimental y por el método de los elementos finitos del estado de tensiones en uniones carpinteras de empalme de llave

In this research, the halved and tabled traditional timber scarf joint is analyzed. This joint consists in two end joint pieces usually subjected to tension. Initially, the study is discussed from an experimental point of view. In this way, 3 critical cross-sections are established (section of the notch, section of the horizontal plane and reduced section) and mechanical tests are performed to achieve the failure on each of critical sections by changing the geometry of the joint. The study is completed by developing a finite element model which allows verify experimental results and extend the analysis to other geometries. This model has to simulate the real behavior of the material which is being studied, so mechanical tests are performed to obtain the elastic constants and the coefficients of friction of the material. In the reduced section, an abrupt decrease of the effective cross-section takes place, and this effect is also experimentally analyzed. These tests indicate that a crack is initiated before the bending-tension failure occurs in the reduced section. The test material consists of wood of Pinus sylvestris L. coming from the “Valsaín´s Sawmill” (Segovia) with “premium quality” according to the nonstructural wood visual classification of sawmill. It is observed that initiation of a crack, in the mortise (bottom of reduced section), and shear stress concentration, at the initial part of the heel (beginning of horizontal plane), completely determine the mechanical behaviour of the joint, resulting in 3 failure modes: local compression failure in the section of the notch, shear failure in the horizontal plane, and failure of stresses concentration, mainly perpendicular to the grain tension, at the bottom of reduced section. The geometric optimization is obtained for halved and tabled traditional scarf joint, when the joint has made with similar properties of wood than tested specimens, for any height and width of the cross-section. It is considered the failure due to the initiation of a crack in reduced section, by applying a correction coefficient into the usual equation used to design the members subjected to both tension and bending. Therefore, it is possible to obtain, analytically, the design conditions to be met of the 3 critical cross-sections. According to the theoretical optimization, the tension strength of complete cross-section is reduced until 14%, when using this type of joint. The experimental optimization indicates even a greater reduction, until 6%. En el presente trabajo de investigación se analiza el comportamiento mecánico de las uniones tradicionales de empalme de llave, que consisten en dos piezas unidas por sus testas transmitiéndose entre ellas principalmente un esfuerzo de tracción. Inicialmente, el estudio se aborda desde un punto de vista experimental. De este modo, se establecen las 3 secciones críticas o de estudio (sección del encaje, sección rasante del cogote y sección reducida) y se realizan ensayos mecánicos, variando la geometría de la unión, para alcanzar la rotura en cada una de ellas. Se completa el estudio mediante la elaboración de un modelo por elementos finitos que permite verificar los resultados experimentales y ampliar el análisis a otras geometrías. Este modelo debe simular el comportamiento real del material objeto de estudio, por lo que se realizan ensayos para obtener las constantes elásticas y los coeficientes de rozamiento del mismo. También se analiza, experimentalmente, el efecto entalladura que reduce bruscamente la sección completa del tirante, estableciendo que el fallo por flexotracción en la sección reducida de la pieza, no llega a producirse por el inicio previo de una grieta. El material de ensayo consiste en madera de Pinus sylvestris L. (pino silvestre) procedente del Aserradero de Valsaín (Segovia) y de calidad “Extra” o “Primera” según la clasificación visual no estructural del aserradero. Se observa que el inicio de una grieta en la mortaja del rediente y la concentración de tensiones tangenciales en la parte inicial del cogote, determinan completamente el comportamiento mecánico de la unión, dando lugar a 3 modos distintos de rotura: fallo por compresión en la sección del encaje, fallo por cortante en la sección rasante y fallo por concentración de tensiones, principalmente tracciones perpendiculares, en el rebaje de la sección reducida. Se consigue optimizar geométricamente cualquier empalme de llave confeccionado con madera de características similares a la ensayada, para cualquier valor de la altura y de la anchura de la sección. Se considera el agotamiento en la sección reducida causado por el inicio de grieta, mediante la aplicación de un coeficiente corrector en la expresión habitual de agotamiento por flexotracción, en consecuencia, finalmente es posible obtener, de modo analítico, un valor del índice de agotamiento en cada una de las 3 secciones de estudio. La optimización teórica del empalme de llave indica que la capacidad resistente del tirante bruto se reduce al 14%, cuando se coloca este tipo de unión tradicional. Experimentalmente se obtiene, que, para la sección ensayada, la capacidad resistente del tirante bruto se reduce todavía más, llegando al 6%.

Magnetic self-field effects on current collection by an ionospheric bare tether

It was recently suggested that the magnetic field created by the current of a bare tether strongly reduces its own electron-collection capability when a magnetic separatrix disconnecting ambient magnetized plasma from tether extends beyond its electric sheath. It is here shown that current reduction by the self-field depends on the ratio meterizing bias and current profiles along the tether (Lt tether length, characteristic length gauging ohmic effects) and on a new dimensionless number Ks involving ambient and tether parameters. Current reduction is weaker the lower Ks and L*/ Lt, which depend critically on the type of cross section: Ks varies as R5/3, h2/3R, and h2/3 1/4 width for wires, round tethers conductive only in a thin layer, and thin tapes, respectively; L* varies as R2/3 for wires and as h2/3 for tapes and round tethers conductive in a layer (R radius, h thickness). Self-field effects are fully negligible for the last two types of cross sections whatever the mode of operation. In practical efficient tether systems having L*/Lt low, maximum current reduction in case of wires is again negligible for power generation; for deorbiting, reduction is <1% for a 10 km tether and 15% for a 20 km tether. In the reboost mode there are no effects for Ks below some threshold; moderate effects may occur in practical but heavy reboost-wire systems that need no dedicated solar power.

Core physics and safety analysis of Generation-IV Sodium Fast Reactors using existing and newly developed computational tools

El futuro de la energía nuclear de fisión dependerá, entre otros factores, de la capacidad que las nuevas tecnologías demuestren para solventar los principales retos a largo plazo que se plantean. Los principales retos se pueden resumir en los siguientes aspectos: la capacidad de proporcionar una solución final, segura y fiable a los residuos radiactivos; así como dar solución a la limitación de recursos naturales necesarios para alimentar los reactores nucleares; y por último, una mejora robusta en la seguridad de las centrales que en definitiva evite cualquier daño potencial tanto en la población como en el medio ambiente como consecuencia de cualquier escenario imaginable o más allá de lo imaginable. Siguiendo estas motivaciones, la Generación IV de reactores nucleares surge con el compromiso de proporcionar electricidad de forma sostenible, segura, económica y evitando la proliferación de material fisible. Entre los sistemas conceptuales que se consideran para la Gen IV, los reactores rápidos destacan por su capacidad potencial de transmutar actínidos a la vez que permiten una utilización óptima de los recursos naturales. Entre los refrigerantes que se plantean, el sodio parece una de las soluciones más prometedoras. Como consecuencia, esta tesis surgió dentro del marco del proyecto europeo CP-ESFR con el principal objetivo de evaluar la física de núcleo y seguridad de los reactores rápidos refrigerados por sodio, al tiempo que se desarrollaron herramientas apropiadas para dichos análisis. Efectivamente, en una primera parte de la tesis, se abarca el estudio de la física del núcleo de un reactor rápido representativo, incluyendo el análisis detallado de la capacidad de transmutar actínidos minoritarios. Como resultado de dichos análisis, se publicó un artículo en la revista Annals of Nuclear Energy [96]. Por otra parte, a través de un análisis de un hipotético escenario nuclear español, se evalúo la disponibilidad de recursos naturales necesarios en el caso particular de España para alimentar una flota específica de reactores rápidos, siguiendo varios escenarios de demanda, y teniendo en cuenta la capacidad de reproducción de plutonio que tienen estos sistemas. Como resultado de este trabajo también surgió una publicación en otra revista científica de prestigio internacional como es Energy Conversion and Management [97]. Con objeto de realizar esos y otros análisis, se desarrollaron diversos modelos del núcleo del ESFR siguiendo varias configuraciones, y para diferentes códigos. Por otro lado, con objeto de poder realizar análisis de seguridad de reactores rápidos, son necesarias herramientas multidimensionales de alta fidelidad específicas para reactores rápidos. Dichas herramientas deben integrar fenómenos relacionados con la neutrónica y con la termo-hidráulica, entre otros, mediante una aproximación multi-física. Siguiendo este objetivo, se evalúo el código de difusión neutrónica ANDES para su aplicación a reactores rápidos. ANDES es un código de resolución nodal que se encuentra implementado dentro del sistema COBAYA3 y está basado en el método ACMFD. Por lo tanto, el método ACMFD fue sometido a una revisión en profundidad para evaluar su aptitud para la aplicación a reactores rápidos. Durante ese proceso, se identificaron determinadas limitaciones que se discutirán a lo largo de este trabajo, junto con los desarrollos que se han elaborado e implementado para la resolución de dichas dificultades. Por otra parte, se desarrolló satisfactoriamente el acomplamiento del código neutrónico ANDES con un código termo-hidráulico de subcanales llamado SUBCHANFLOW, desarrollado recientemente en el KIT. Como conclusión de esta parte, todos los desarrollos implementados son evaluados y verificados. En paralelo con esos desarrollos, se calcularon para el núcleo del ESFR las secciones eficaces en multigrupos homogeneizadas a nivel nodal, así como otros parámetros neutrónicos, mediante los códigos ERANOS, primero, y SERPENT, después. Dichos parámetros se utilizaron más adelante para realizar cálculos estacionarios con ANDES. Además, como consecuencia de la contribución de la UPM al paquete de seguridad del proyecto CP-ESFR, se calcularon mediante el código SERPENT los parámetros de cinética puntual que se necesitan introducir en los típicos códigos termo-hidráulicos de planta, para estudios de seguridad. En concreto, dichos parámetros sirvieron para el análisis del impacto que tienen los actínidos minoritarios en el comportamiento de transitorios. Concluyendo, la tesis presenta una aproximación sistemática y multidisciplinar aplicada al análisis de seguridad y comportamiento neutrónico de los reactores rápidos de sodio de la Gen-IV, usando herramientas de cálculo existentes y recién desarrolladas ad' hoc para tal aplicación. Se ha empleado una cantidad importante de tiempo en identificar limitaciones de los métodos nodales analíticos en su aplicación en multigrupos a reactores rápidos, y se proponen interesantes soluciones para abordarlas. ABSTRACT The future of nuclear reactors will depend, among other aspects, on the capability to solve the long-term challenges linked to this technology. These are the capability to provide a definite, safe and reliable solution to the nuclear wastes; the limitation of natural resources, needed to fuel the reactors; and last but not least, the improved safety, which would avoid any potential damage on the public and or environment as a consequence of any imaginable and beyond imaginable circumstance. Following these motivations, the IV Generation of nuclear reactors arises, with the aim to provide sustainable, safe, economic and proliferationresistant electricity. Among the systems considered for the Gen IV, fast reactors have a representative role thanks to their potential capacity to transmute actinides together with the optimal usage of natural resources, being the sodium fast reactors the most promising concept. As a consequence, this thesis was born in the framework of the CP-ESFR project with the generic aim of evaluating the core physics and safety of sodium fast reactors, as well as the development of the approppriated tools to perform such analyses. Indeed, in a first part of this thesis work, the main core physics of the representative sodium fast reactor are assessed, including a detailed analysis of the capability to transmute minor actinides. A part of the results obtained have been published in Annals of Nuclear Energy [96]. Moreover, by means of the analysis of a hypothetical Spanish nuclear scenario, the availability of natural resources required to deploy an specific fleet of fast reactor is assessed, taking into account the breeding properties of such systems. This work also led to a publication in Energy Conversion and Management [97]. In order to perform those and other analyses, several models of the ESFR core were created for different codes. On the other hand, in order to perform safety studies of sodium fast reactors, high fidelity multidimensional analysis tools for sodium fast reactors are required. Such tools should integrate neutronic and thermal-hydraulic phenomena in a multi-physics approach. Following this motivation, the neutron diffusion code ANDES is assessed for sodium fast reactor applications. ANDES is the nodal solver implemented inside the multigroup pin-by-pin diffusion COBAYA3 code, and is based on the analytical method ACMFD. Thus, the ACMFD was verified for SFR applications and while doing so, some limitations were encountered, which are discussed through this work. In order to solve those, some new developments are proposed and implemented in ANDES. Moreover, the code was satisfactorily coupled with the thermal-hydraulic code SUBCHANFLOW, recently developed at KIT. Finally, the different implementations are verified. In addition to those developments, the node homogenized multigroup cross sections and other neutron parameters were obtained for the ESFR core using ERANOS and SERPENT codes, and employed afterwards by ANDES to perform steady state calculations. Moreover, as a result of the UPM contribution to the safety package of the CP-ESFR project, the point kinetic parameters required by the typical plant thermal-hydraulic codes were computed for the ESFR core using SERPENT, which final aim was the assessment of the impact of minor actinides in transient behaviour. All in all, the thesis provides a systematic and multi-purpose approach applied to the assessment of safety and performance parameters of Generation-IV SFR, using existing and newly developed analytical tools. An important amount of time was employed in identifying the limitations that the analytical nodal diffusion methods present when applied to fast reactors following a multigroup approach, and interesting solutions are proposed in order to overcome them.

Magnetic self-field effects on bare-tether current collection

It has been recently suggested that the magnetic field created by the current in a bare tether could sensibly reduce its electron collection capability in the magnetised ionosphere, a region of closed magnetic surfaces disconnecting the cylinder from infinity. In this paper, the ohmic voltage drop along the tether is taken into account in considering self-field effects. Separate analyses are carried out for the thrust and power generation and drag modes of operation, which are affected in different ways. In the power generation and drag modes, bias decreases as current increases along the tether, starting at the anodic, positively-biased end (upper end in the usual, eastward-flying spacecraft); in the thrust mode of operation, bias increases as current increases along the tether, starting at the lower end. When the ohmic voltage drop is considered, self-field effects are shown to be weak, in all cases, for tape tethers, and for circular cross-section tethers just conductive in a thin outer layer. Self-field effects might become important, in the drag case only, for tethers with fully conductive cross sections that are unrealistically heavy.

Benchmarking of calculation schemes in Apollo2 and COBAYA3 for VVER lattices

This paper presents solutions of the NURISP VVER lattice benchmark using APOLLO2, TRIPOLI4 and COBAYA3 pin-by-pin. The main objective is to validate MOC based calculation schemes for pin-by-pin cross-section generation with APOLLO2 against TRIPOLI4 reference results. A specific objective is to test the APOLLO2 generated cross-sections and interface discontinuity factors in COBAYA3 pin-by-pin calculations with unstructured mesh. The VVER-1000 core consists of large hexagonal assemblies with 2mm inter-assembly water gaps which require the use of unstructured meshes in the pin-by-pin core simulators. The considered 2D benchmark problems include 19-pin clusters, fuel assemblies and 7-assembly clusters. APOLLO2 calculation schemes with the step characteristic method (MOC) and the higher-order Linear Surface MOC have been tested. The comparison of APOLLO2 vs.TRIPOLI4 results shows a very close agreement. The 3D lattice solver in COBAYA3 uses transport corrected multi-group diffusion approximation with interface discontinuity factors of GET or Black Box Homogenization type. The COBAYA3 pin-by-pin results in 2, 4 and 8 energy groups are close to the reference solutions when using side-dependent interface discontinuity factors.

Application of a Bayesian/Generalised Least-Squares method to generate correlations between independent neutron fission yield data

Fission product yields are fundamental parameters for several nuclear engineering calculations and in particular for burn-up/activation problems. The impact of their uncertainties was widely studied in the past and valuations were released, although still incomplete. Recently, the nuclear community expressed the need for full fission yield covariance matrices to produce inventory calculation results that take into account the complete uncertainty data. In this work, we studied and applied a Bayesian/generalised least-squares method for covariance generation, and compared the generated uncertainties to the original data stored in the JEFF-3.1.2 library. Then, we focused on the effect of fission yield covariance information on fission pulse decay heat results for thermal fission of 235U. Calculations were carried out using different codes (ACAB and ALEPH-2) after introducing the new covariance values. Results were compared with those obtained with the uncertainty data currently provided by the library. The uncertainty quantification was performed with the Monte Carlo sampling technique. Indeed, correlations between fission yields strongly affect the statistics of decay heat. Introduction Nowadays, any engineering calculation performed in the nuclear field should be accompanied by an uncertainty analysis. In such an analysis, different sources of uncertainties are taken into account. Works such as those performed under the UAM project (Ivanov, et al., 2013) treat nuclear data as a source of uncertainty, in particular cross-section data for which uncertainties given in the form of covariance matrices are already provided in the major nuclear data libraries. Meanwhile, fission yield uncertainties were often neglected or treated shallowly, because their effects were considered of second order compared to cross-sections (Garcia-Herranz, et al., 2010). However, the Working Party on International Nuclear Data Evaluation Co-operation (WPEC)