A novel method for radio propagation simulation based on automatic 3D environment reconstruction

In this paper, a novel method to simulate radio propagation is presented. The method consists of two steps: automatic 3D scenario reconstruction and propagation modeling. For 3D reconstruction, a machine learning algorithm is adopted and improved to automatically recognize objects in pictures taken from target region, and 3D models are generated based on the recognized objects. The propagation model employs a ray tracing algorithm to compute signal strength for each point on the constructed 3D map. By comparing with other methods, the work presented in this paper makes contributions on reducing human efforts and cost in constructing 3D scene; moreover, the developed propagation model proves its potential in both accuracy and efficiency.

Desarrollo de la radio en el marco de las rivalidades político-militares de principios del siglo XX

A lo largo de este proyecto, se analizarán los comienzos de la radio en las primeras décadas del siglo XX, teniendo como objetivo describir el desarrollo científico-tecnológico y las rivalidades político-militares de las potencias europeas de Reino Unido y Alemania. En primer lugar se verán los precursores de la radio que existían anteriormente al surgimiento de la radiotelegrafía como la telegrafía óptica, la telegrafía eléctrica o el teléfono. Al igual que los primeros investigadores, como James Clerk Maxwell o Heinrich Rudolf Hertz, gracias a los cuales el origen de la radio fue posible. También se analizará el contexto histórico-político de Reino Unido y Alemania donde se muestran las características de las dos grandes potencias del momento, el Imperio Británico y el Imperio Alemán. Además, la cada vez mayor importancia de la telegrafía sin hilos, hará necesaria una organización internacional, dando lugar a las Conferencias Internacionales de Radiotelegrafía y que enfrentarán a estas dos potencias por defender sus intereses. Guillermo Marconi, por parte de Reino Unido, y Telefunken, por parte de Alemania, serán las principales marcas comerciales de radiotelegrafía, no solo en sus respectivos países, sino también en el resto del mundo. Entre ambas compañías se verán las rivalidades por la incesante lucha de patentes, el desarrollo tecnológico y el control de los mercados. También se tratará el enfrentamiento directo que se produjo en la Primera Guerra Mundial, donde la radio jugaría un papel fundamental. Por último, se analizarán los comienzos de la radiodifusión en la segunda década del siglo XX, donde la radio ya estaba consolidada como uno de los medios de comunicación más importante de la época, capaz de llegar a todos los rincones del planeta y perfectamente integrada en la sociedad del momento. ABSTRACT. Throughout this project, it will be analyzed the beginning of the radio in the first decades of the XX century, having as goal to describe the scientific-technological development and the political-militaries opponents of the European’s countries, United kingdom and Germany. Firstly, it will be shown the radio’s precursors before the origin of the wireless telegraphy, like: optical telegraphy, electric telegraphy or telephone. Moreover, it will show the first researchers like: Clerk Maxwell or Heinrich Hertz, thanks to them, the origin of the radio was possible. In addition, it will analyze the historical-political context of United Kingdom and Germany, where it is shown the main features of the Britain Empire and the German Empire. Moreover, the importance of the telegraphy without wire will make necessary and international organization, resulting the International Conferences of Wireless Telegraphy and it will put together these main countries in order to protect their interests. Guglielmo Marconi, by United Kingdom, and Telefunken, by Germany, they will be the main commercials brand of the wireless telegraphy, not only in their countries, but also in all over the world. Between both companies will be seen the main competitions for their patens, the technology development and the market’s control. Moreover, it will be dealt the direct conflict in the First World of War, where the radio has a fundamental role. Finally, it will be analyze the beginning of the wireless broadcasting in the second decade of the XX century, where the radio was established as one of the most important media of the age, able to arrive at every places of the world and it was perfectly integrated in the society of that moment.

Implementation of wireless communication based on Software Defined Radio

In current communication systems, there are many new challenges like various competitive standards, the scarcity of frequency resource, etc., especially the development of personal wireless communication systems result the new system update faster than ever before, the conventional hardware-based wireless communication system is difficult to adapt to this situation. The emergence of SDR enabled the third revolution of wireless communication which from hardware to software and build a flexible, reliable, upgradable, reusable, reconfigurable and low cost platform. The Universal Software Radio Peripheral (USRP) products are commonly used with the GNU Radio software suite to create complex SDR systems. GNU Radio is a toolkit where digital signal processing blocks are written in C++, and connected to each other with Python. This makes it easy to develop more sophisticated signal processing systems, because many blocks already written by others and you can quickly put them together to create a complete system. Although the main function of GNU Radio is not be a simulator, but if there is no RF hardware components,it supports to researching the signal processing algorithm based on pre-stored and generated data by signal generator. This thesis introduced SDR platform from hardware (USRP) and software(GNU Radio), as well as some basic modulation techniques in wireless communication system. Based on the examples provided by GNU Radio, carried out some related experiments, for example GSM scanning and FM radio station receiving on USRP. And make a certain degree of improvement based on the experience of some investigators to observe OFDM spectrum and simulate real-time video transmission. GNU Radio combine with USRP hardware proved to be a valuable lab platform for implementing complex radio system prototypes in a short time. RESUMEN. Software Defined Radio (SDR) es una tecnología emergente que está creando un impacto revolucionario en la tecnología de radio convencional. Un buen ejemplo de radio software son los sistemas de código abierto llamados GNU Radio que emplean un kit de herramientas de desarrollo de software libre. En este trabajo se ha empleado un kit de desarrollo comercial (Ettus Research) que consiste en un módulo de procesado de señal y un hardaware sencillo. El módulo emplea un software de desarrollo basado en Linux sobre el que se pueden implementar aplicaciones de radio software muy variadas. El hardware de desarrollo consta de un microprocesador de propósito general, un dispositivo programable (FPGA) y un interfaz de radiofrecuencia que cubre de 50 a 2200MHz. Este hardware se conecta al PC por medio de un interfaz USB de 8Mb/s de velocidad. Sobre la plataforma de Ettus se pueden ejecutar aplicaciones GNU radio que utilizan principalmente lenguaje de programación Python para implementarse. Sin embargo, su módulo de procesado de señal está construido en C + + y emplea un microprocesador con aritmética de coma flotante. Por lo tanto, los desarrolladores pueden rápida y fácilmente construir aplicaciones en tiempo real sistemas de comunicación inalámbrica de alta capacidad. Aunque su función principal no es ser un simulador, si no puesto que hay componentes de hardware RF, Radio GNU sirve de apoyo a la investigación del algoritmo de procesado de señales basado en pre-almacenados y generados por los datos del generador de señal. En este trabajo fin de máster se ha evaluado la plataforma de hardware de DEG (USRP) y el software (GNU Radio). Para ello se han empleado algunas técnicas de modulación básicas en el sistema de comunicación inalámbrica. A partir de los ejemplos proporcionados por GNU Radio, hemos realizado algunos experimentos relacionados, por ejemplo, escaneado del espectro, demodulación de señales de FM empleando siempre el hardware de USRP. Una vez evaluadas aplicaciones sencillas se ha pasado a realizar un cierto grado de mejora y optimización de aplicaciones complejas descritas en la literatura. Se han empleado aplicaciones como la que consiste en la generación de un espectro de OFDM y la simulación y transmisión de señales de vídeo en tiempo real. Con estos resultados se está ahora en disposición de abordar la elaboración de aplicaciones complejas.

Radio propagation modeling and measurements for ZigBee based indoor wireless sensor networks

The deployment of nodes in Wireless Sensor Networks (WSNs) arises as one of the biggest challenges of this field, which involves in distributing a large number of embedded systems to fulfill a specific application. The connectivity of WSNs is difficult to estimate due to the irregularity of the physical environment and affects the WSN designers? decision on deploying sensor nodes. Therefore, in this paper, a new method is proposed to enhance the efficiency and accuracy on ZigBee propagation simulation in indoor environments. The method consists of two steps: automatic 3D indoor reconstruction and 3D ray-tracing based radio simulation. The automatic 3D indoor reconstruction employs unattended image classification algorithm and image vectorization algorithm to build the environment database accurately, which also significantly reduces time and efforts spent on non-radio propagation issue. The 3D ray tracing is developed by using kd-tree space division algorithm and a modified polar sweep algorithm, which accelerates the searching of rays over the entire space. Signal propagation model is proposed for the ray tracing engine by considering both the materials of obstacles and the impact of positions along the ray path of radio. Three different WSN deployments are realized in the indoor environment of an office and the results are verified to be accurate. Experimental results also indicate that the proposed method is efficient in pre-simulation strategy and 3D ray searching scheme and is suitable for different indoor environments.

Implementación y configuración de un receptor de radio definido por software (SDR) para estudios de propagación

The constant development of digital systems in radio communications demands the adaptation of the current receiving equipment to the new technologies. In this context, a new Software Defined Radio based receiver is being implemented with the aim of carrying out different experiments to analyze the propagation of signals through the atmosphere from a satellite beacon. The receiver selected for this task is the PERSEUS SDR from the Italian company Microtelecom s.r.l. It is a software defined VLF-LF-MF-HF receiver based on an outstanding direct sampling digital architecture which features a 14 bit 80 MSamples/s analog-to-digital converter, a high-performance FPGA-based digital down-converter and a high-speed 480 Mbit/s USB2.0 PC interface. The main goal is to implement the related software and adapt the new receiver to the current working environment. In this paper, SDR technology guidelines are given and PERSEUS receiver digital signal processing is presented with the most remarkable results.

AR modelling and DDS for in situ surveillance of capacitive pressure transmitters

In this work, a methodology is proposed to find the dynamics poles of a capacitive pressure transmitter in order to enhance and extend the on line surveillance of this type of sensors based on the response time measurement by applying noise analysis techniques and the Dynamic Data System. Several measurements have been analyzed taken from a Pressurized Water Reactor. The methodology proposes an autoregressive fit whose order is determined by the sensor dynamics poles. Nevertheless, the signals that have been analyzed, could not be filtered properly in order to remove the plant noise, thus, this was considered as an additional pair of complex conjugate poles. With this methodology we have come up with the numerical value of the sensor second real pole in spite of its low influence on the sensor dynamic response. This opens up a more accurate on line sensor surveillance since the previous methods were achieved by considering one real pole only.

Measurements and modelling of radio propagation in subway tunnels

The work presented in this article is focused on the RF measurement campaign carried out in several subway tunnels in Metro Madrid (Spain). Most common segments such as straight lines, curves and passing through station as well as other unique scenarios in metropolitan lines were the selected locations during this campaign. Measurements were conducted in tunnels of diverse cross section shapes and taken at three frequency bands: 900 MHz, 2.4GHz and 5.7 GHz for both horizontal and vertical polarization.

Application and modeling of GaN FET in 1MHz large signal bandwidth power supply for radio frequency power amplifier

In this paper, implementation and testing of non- commercial GaN HEMT in a simple buck converter for envelope amplifier in ET and EER transmission techn iques has been done. Comparing to the prototypes with commercially available EPC1014 and 1015 GaN HEMTs, experimentally demonstrated power supply provided better thermal management and increased the switching frequency up to 25MHz. 64QAM signal with 1MHz of large signal bandw idth and 10.5dB of Peak to Average Power Ratio was gener ated, using the switching frequency of 20MHz. The obtaine defficiency was 38% including the driving circuit an d the total losses breakdown showed that switching power losses in the HEMT are the dominant ones. In addition to this, some basic physical modeling has been done, in order to provide an insight on the correlation between the electrical characteristics of the GaN HEMT and physical design parameters. This is the first step in the optimization of the HEMT design for this particular application.

Positional Accuracy in Smart-Phones and Its Effect on LBS Applications.

Location-based services (LBS) highly rely on the location of the mobile user in order to provide the service tailored to that location. This location is calculated differently depending on the technology available in the used mobile device. No matter which technology is used, the location will never be calculated 100% correctly; instead there will always be a margin of error generated during the calculation, which is referred to as positional accuracy. This research has reviewed the eight most common positioning technologies available in the major current smart-phones and assessed their positional accuracy with respect to its usage by LBS applications. Given the vast majority of these applications, this research classified them into thirteen categories, and these categories were also classified depending on their level criticality as low, medium, or high critical, and whether they function indoor or outdoor. The accuracies of different positioning technologies are compared to these two criteria. Low critical outdoor and high critical indoor applications were found technologically covered; high and medium critical outdoor ones weren?t fully resolved. Finally three potential solutions are suggested to be implemented in future smartphones to resolve this technological gap: Real-Time Kinematics Global Positioning System (RTK GPS), terrestrial transmitters, and combination of Wireless Sensors Network and Radio Frequency Identification (WSN-RFID).

Experimental investigation of radio signal propagation in scientific facilities for telerobotic applications

Understanding the radio signal transmission characteristics in the environment where the telerobotic application is sought is a key part of achieving a reliable wireless communication link between a telerobot and a control station. In this paper, wireless communication requirements and a case study of a typical telerobotic application in an underground facility at CERN are presented. Then, the theoretical and experimental characteristics of radio propagation are investigated with respect to time, distance, location and surrounding objects. Based on analysis of the experimental findings, we show how a commercial wireless system, such as Wi-Fi, can be made suitable for a case study application at CERN.

Influencia del radio en entallas en U sometidas a flexión en tres puntos en la fundición GG-25

El presente trabajo fin de master se centra en estudiar el efecto del radio de entalla en la fundición gris GG-25, sometida a cargas en modo I (propagación de fisuras a partir de la entalla por fuerzas de tracción exclusivamente). En teoría, en un material frágil, a menor radio de entalla, la carga critica de rotura debería ser también menor. Sin embargo, en la tesis fin de master “Static tests under torsion loading of notched specimens made of grey cast iron: Experimental issues and Numerical Development” realizada por el estudiante Marco Marcón, de la Universidad de Padua, Italia, con este mismo material pero con solicitación en modo III, se observo que a menor radio de entalla, la carga de rotura de las probetas aumentaba. Para estudiar dicho efecto de entalla, se ha llevado a cabo una campana experimental Ensayándose 20 probetas agrupadas en cuatro radios de entalla. Posteriormente se realizaron simulaciones numéricas para comprobar el comportamiento del material y corroborar los resultados experimentales obtenidos, mediante el modelo de la fisura cohesiva implementada junto con un material de Hencky en el continuo.

High brightness semiconductor lasers as transmitters for space lidar systems

High brightness semiconductor lasers are potential transmitters for future space lidar systems. In the framework of the European Project BRITESPACE, we propose an all-semiconductor laser source for an Integrated Path Differential Absorption lidar system for column-averaged measurements of atmospheric CO2 in future satellite missions. The complete system architecture has to be adapted to the particular emission properties of these devices using a Random Modulated Continuous Wave approach. We present the initial experimental results of the InGaAsP/InP monolithic Master Oscillator Power Amplifiers, providing the ON and OFF wavelengths close to the selected absorption line around 1572 nm.

Distributed cognitive radio systems with temperature-interference constraints and overlay scheme

Cognitive radio represents a promising paradigm to further increase transmission rates in wireless networks, as well as to facilitate the deployment of self-organized networks such as femtocells. Within this framework, secondary users (SU) may exploit the channel under the premise to maintain the quality of service (QoS) on primary users (PU) above a certain level. To achieve this goal, we present a noncooperative game where SU maximize their transmission rates, and may act as well as relays of the PU in order to hold their perceived QoS above the given threshold. In the paper, we analyze the properties of the game within the theory of variational inequalities, and provide an algorithm that converges to one Nash Equilibrium of the game. Finally, we present some simulations and compare the algorithm with another method that does not consider SU acting as relays.

Simulación del enlace descendente LTE orientada a planificación radio

En este Proyecto de Fin de Carrera se describe la implementación de un simulador del enlace descendente de un sistema LTE. Dicho simulador es capaz de modelar con precisión las variaciones rápidas del canal, que se producen debido al efecto del multitrayecto. Esto es vital a la hora de simular adecuadamente las ganancias que se logran debido a la planificación dependiente del canal que el sistema LTE es capaz de realizar. El objetivo es investigar la relación existente entre la tasa de datos binaria obtenida por una estación base y diferentes parámetros de los usuarios (como SINR o velocidad). El objetivo final del proyecto es obtener un modelo que pueda predecir la tasa binaria de la base como una función de algunos parámetros que caractericen las condiciones de los usuarios. Se ha utilizado principalmente un planificador de tipo “proportional fair” debido a sus cualidades para para obtener una tasa binaria razonablemente elevada a la vez que reparte el canal entre todos los usuarios existentes de forma equitativa.

Despliegue de una red de acceso radio en comunicaciones móviles

En el mundo actual el uso de la telefonía móvil ha desbancado a la telefonía fija, creando la necesidad en los usuarios de estar conectados independientemente del lugar en el que se encuentren. Esto provoca que las compañías telefónicas estén cada vez más preocupadas por mejorar y renovar sus redes de comunicaciones para proporcionar sus servicios con cada vez mayor calidad. En este proyecto se estudiara la forma en la que un gran operador mantiene su red actualizada y se detallaran los trabajos necesarios para que su red se mantenga actualizada y no se encuentren equipos obsoletos dentro de su arquitectura. Se describirá el procedimiento mediante el cual una operadora de telefonía móvil ha llevado a cabo la renovación de los equipos de su red de acceso. A lo largo del proyecto se describirán los diferentes tipos de escenarios y las distintas soluciones adoptadas a implementar en dichos escenarios. De la misma forma se describirá el tipo de equipo instalado, indicando las diferentes tarjetas que lo forman y sus diferentes funcionalidades. Se describirán las acciones llevadas a cabo por el grupo de O&M de integración mediante las cuales se retirara el equipo antiguo y se instalara el nuevo impactando lo menos posible en la red del operador. ABSTRACT. In today's world the use of mobile phones has replaced fixed lines, creating the need for users to stay connected no matter where they are located. This causes the phone companies are increasingly concerned with improving and renovating their communications networks to provide services with increasing quality. In this project the way in which a large network operator maintains their network updated and detailing the work required to keep it updated and with no obsolete equipment in its architecture are be considered. The process by which a mobile operator has undertaken the renovation of the computers on your network access will be described. Throughout the project the different types of scenarios and different solutions adopted to implement these scenarios are described. Likewise the type of installed equipment is also described, indicating the different cards that form it and its various functions. Actions carried out by the group of O & M of integration by which the old equipment is retired and the new install as little as possible impact on the operator's network will be described.