Non-destructive methods to estimate physical aging of plywood

This paper studies the relationship between aging, physical changes and the results of non-destructive testing of plywood. 176 pieces of plywood were tested to analyze their actual and estimated density using non-destructive methods (screw withdrawal force and ultrasound wave velocity) during a laboratory aging test. From the results of statistical analysis it can be concluded that there is a strong relationship between the non-destructive measurements carried out, and the decline in the physical properties of the panels due to aging. The authors propose several models to estimate board density. The best results are obtained with ultrasound. A reliable prediction of the degree of deterioration (aging) of board is presented.

A Multiagent system model which suggests solutions to fuzzy incidents in the field of telecommunications

This article presents the model of a multi-agent system (SMAF), which objectives are the input of fuzzy incidents as the human experts express them with different severities degrees and the further search and suggestion of solutions. The solutions will be later confirm or not by the users. This model was designed, implemented and tested in the telecommunications field, with heterogeneous agents in a cooperative model. In the design, different abstract levels where considered, according to the agents? objectives, their ways to carry it out and the environment in which they act. Each agent is modeled with different spectrum of the knowledge base

E.1027. Maison en bord de mer: Theoretical Restoration

E.1027, Maison en bord de mer is a small villa in Roquebrune Cap-Martin, built by architects Eileen Gray and Jean Badovici between 1926 and 1929. It was hailed as a landmark of modern architecture, and then forgotten. Over the years many transformations have been carried out, and these changes have altered the spatial qualities of the original project. Time and neglect have taken their toll, and until 2008 the villa was abandoned, a shadow of its former self. In order to state an appropriate restoration, a description of the house and its historic evolution has been made, comparing plans of its different transformations. After compiling the most common pathologies and restoration procedures in buildings of the Modern Movement in general, the particular pathologies of E.1027 are presented, concluding with a restoration proposal for E.1027 that considers aesthetical as well as technical aspects. This study involves an attempt to establish guidelines for the theoretical and technical aspects for restoration of architecture of the Modern Movement, using the Maison en bord de mer as an example.

Las presentaciones de trabajo en lengua inglesa: una propuesta de curso on-line.

Desde la explosión de crecimiento de internet que comenzó en los años 90, se han ido creando y poniendo a disposición de los usuarios diversas herramientas para compartir información y servicios de diversas formas, desde el nacimiento del primer navegador hasta nuestros días, donde hay infinidad de lenguajes aplicables al ámbito web. En esta fase de crecimiento, en primer lugar, de cara a usuarios individuales, saldrían herramientas que permitirían a cada cual hacer su web personal, con sus contenidos expuestos. Más adelante se fue generando el fenómeno “comunidad”, con, por ejemplo, foros, o webs en las que había múltiples usuarios que disfrutaban de contenidos o servicios que la web ofreciese. Este crecimiento del mundo web en lo comunitario ha avanzado en muchas ramas,entre ellas, por supuesto, la educacional, surgiendo plataformas como la que es base del proyecto que a continuación se presenta, y herramienta básica y prácticamente ya imprescindible en la enseñanza universitaria: Moodle. Moodle es una herramienta diseñada para compatir recursos y diseñar actividades para el usuario potencial, complementando su aprendizaje en aula, o incluso siendo una vía autónoma de aprendizaje en sí misma. Se ha realizado un estudio sobre el estado de saludo de los contenidos que se exponen en Moodle, y se ha encontrado que una gran mayoría de los cursos que se pueden visitar tienen un gran número de carencias. Por un lado, hay pocos con material original explotado exclusivamente para el curso, y, si tienen material original, no se ha observado una especial atención por la maquetación. Por otro lado, hay muchos otros sin material original, y, en ambos casos, no se ha encontrado ningún curso que ofrezca material audiovisual exclusivo para el curso, presentando algunos en su lugar material audiovisual encontrado en la red (Youtube, etc). A la vista de estos hechos, se ha realizado un proyecto que intenta aportar soluciones ante estas carencias, y se presenta un curso procedente de diversas referencias bibliográficas, para la parte textual, y material audiovisual original e inédito que también se ha explotado específicamente para este curso. Este material ha sido por un lado vídeo, que se ha visionado, editado y subtitulado con software de libre distribución, y por otro lado, audio, que complementa un completo glosario que se ha añadido como extra al curso y cuyo planteamiento no se ha encontrado en ningún curso online de los revisados. Todo esto se ha envuelto en una maquetación cuidada que ha sido fruto del estudio de los lenguajes web html y CSS, de forma que, por un lado, el curso sea un lugar agradable en el que aprender dentro de internet, y por otro, se pudiesen realizar ciertas operaciones que sin estos conocimientos habrían sido imposibles, como la realización del glosario o la incrustación de imágenes y vídeos. A su vez, se ha tratado de dar un enfoque didáctico a toda la memoria del proyecto, de forma que pueda ser de utilidad a un usuario futuro que quisiese profundizar en los usos de Moodle, introducirse en el lenguaje web, o introducirse en el mundo de la edición de vídeo. ABSTRACT: Since the explosion of Internet growth beginning in the 90s, many tools have been created and made available for users to share information and services in various ways, from the birth of the first browser until today, where there are plenty of web programming languages. This growth stage would give individual users tools that would allow everyone to make an own personal website, with their contents exposed. Later, the "community" phenomenon appeared with, for example, forums, or websites where multiple users enjoyed the content or web services that those websites offered. Also, this growth in the web community world has progressed in many fields, including education, with the emerge of platforms such as the one that this project uses as its basis, and which is the basic and imperative tool in college education: Moodle. Moodle is a tool designed to share resources and design activities for the potential user, completing class learning, or even letting this user learn in an autonomous way. In this project a study on the current situation of the content present in Moodle courses around the net has been carried out, and it has been found that most of them lack of original material exploited exclusively for the courses, and if they have original material, there has been not observed concern on the layout where that material lies. On the other hand, there are many other with non original material, and in both cases, there has not been found any course that offers audio- visual material made specifically for the course, instead of presenting some audiovisual material found on the net (Youtube, etc). In view of these facts, the project presented here seeks to provide solutions to these shortcomings, presenting a course with original material exploited from various references, and unpublished audioevisual material which also has been exploited specifically for this course. This material is, on one hand, video, which has been viewed, edited and subtitled with free software, and on the other, audio, which complements a comprehensive glossary that has been added as an extra feature to the course and whose approach was not found in any of the online courses reviewed. All of this has been packaged in a neat layout that has been the result of the study of web languages HTML and CSS, so that first, the course was a pleasant place to learn on the internet, and second, certain operations could be performed which without this knowledge would have been impossible, as the glossary design or embedding images and videos. Furthermore, a didactic approach has been adopted to the entire project memory, so it can be useful to a future user who wanted to go deeper on the uses of Moodle, containing an intro into the web language, or in the world video editing.

Desarrollos para la explotación de datos integrados mediante fotogrametría y láser escáner en proyectos de patrimonio arquitectónico

La presente tesis doctoral describe los desarrollos realizados, y finalmente materializados en patentes con registro de la propiedad intelectual, para la integración de las nuevas tecnologías de documentación fotogramétrica y las bases de datos de los barredores láser terrestres, en los procesos de elaboración, redacción y ejecución de proyectos de restauración y rehabilitación arquitectónicos. Los avances tecnológicos aparecidos en control métrico, junto con las técnicas de imagen digital y los desarrollos fotogramétricos, pueden aportar mejoras significativas en el proceso proyectual y permiten aplicar nuevos procedimientos de extracción de datos para generar de forma sencilla, bajo el control directo y supervisión de los responsables del proyecto, la información métrica y documental más adecuada. Se establecen como principios, y por tanto como base para el diseño de dicha herramienta, que los desarrollos aparecidos sí han producido el uso extendido del sistema CAD (como instrumento de dibujo) así como el uso de la imagen digital como herramienta de documentación. La herramienta a diseñar se fundamenta por tanto en la imagen digital (imágenes digitales, imágenes rectificadas, ortofotografías, estéreo- modelos, estereo- ortofotografías) así como su integración en autocad para un tratamiento interactivo. En la aplicación de la fotogrametría a la disciplina arquitectónica, se considera de interés estructurar aplicaciones con carácter integrador que, con mayores capacidades de interactuación y a partir de información veraz y rigurosa, permitan completar o elaborar documentos de interés proyectual, ABSTRACT This doctoral thesis explains the developments carried out, and finally patented with intellectual property rights, for the integration of the new photogrammetric technology documentation and terrestrial scanner databases in the preparation, documentation and implementation processes of restoration projects and architectural renovation. The technological advances in metric control, as well as the digital image techniques and photogrammetric developments, can together bring a significant improvement to the projecting process, and, under the direct control and supervision of those in charge of the project, can allow new data extraction processes to be applied in order to easily generate the most appropriate metric information and documentation. The principles and, therefore, the basis for the design of this tool are that the developments have indeed produced the widespread use of the CAD system (as a drawing instrument) and the use of digital images as a documentation tool. The tool to be designed is therefore based on digital images (rectify images, orthophotos, stereomodels, stereo-orthophotos) as well as its integration in Autocad for interactive processing. In the application of photogrammetry to the architectural discipline, what interests us is to structure applications of an integrative nature which, with a greater capacity for interaction and from accurate and thorough information, enable the completion or elaboration of documents that are of interest to the project.

Time-frequency characterization of a sound propagation channel as an educational tool

This paper discusses the use of sound waves to illustrate multipath radio propagation concepts. Specifically, a procedure is presented to measure the time-varying frequency response of the channel. This helps demonstrate how a propagation channel can be characterized in time and frequency, and provides visualizations of the concepts of coherence time and coherence bandwidth. The measurements are very simple to carry out, and the required equipment is easily available. The proposed method can be useful for wireless or mobile communication courses.

El Terremoto de Lorca (2011) en el contexto de la peligrosidad y el riesgo sísmico en Murcia.

Este trabajo presenta un análisis de diferentes aspectos relacionados con el sismo principal del 11 de Mayo de 2011, con epicentro en las proximidades de Lorca, que abarcan desde el movimiento fuerte registrado hasta el daño observado en diferentes tipologías constructivas, contrastando todo ello con los resultados de estudios previos de peligrosidad y riesgo sísmico en la provincia de Murcia. La cuestión esencial que se plantea en el análisis es si tanto el movimiento como el daño entraban dentro de lo esperado o pueden considerarse anómalos en el marco del riesgo sísmico del sureste de España. A este respecto se hacen una serie de reflexiones y se extraen lecciones aprendidas del terremoto, que llevan a proponer recomendaciones de cara a la revisión de la Norma Sismorresistente Española, así como a definir medidas para la reducción del riesgo sísmico en la región. Abstract: An analysis of the different aspects related to the May 11th, 2011 Lorca earthquake is presented,covering recorded ground motions, damage observed in different building typologies, and contrasting these observations with previous results on seismic hazard and seismic risk obtained in the province of Murcia. The essential question addressed in the analysis is whether observed ground motions and physical damage can be considered as expected or as anomalous in the frame of seismic risk in southeastern Spain. In this respect, a number of reflections are carried out and several learned lessons from the earthquake are extracted, which leads to the proposal of different recommendations for the future revision of the Spanish earthquake-resistant provisions, as well as for defining risk reduction measurements in the region.

Método CSORA: la búsqueda de conocimiento

En este artículo se ofrece una visión rápida de las necesidades del uso de buscadores para la gestión del conocimiento y de las ideas básicas de su funcionamiento. A continuación se presenta el método CSORA (Classify, Search, Organize, Relate, Adapt), conjunto de procedimientos técnicos y metodológicos que mejoran la eficacia de los buscadores haciendo posible encontrar información relevante en entornos con mucha información o información especializada. Finalmente se muestra su integración en los motores de búsqueda y en las conclusiones se incluyen las ventajas de su uso, verificadas a través de experiencias realizadas y las líneas de investigación futuras. ABSTRACT: In this paper we offer a fast overview of the usage needs of search engines for knowledge management, as well as the basic ideas about how they work. We then present the CSORA method (Classify, Search, Organize, Relate and Adapt), a set of technical and methodological procedures that improve the efficacy of search engines, making it possible to find relevant information in environments with lots of information or specialized information. Last, we show the integration of the method into the search engines. The conclusions include a description of the advantages of using this method, verified by experiments carried out, and the lines of future work.

Biomolecular interaction analysis of gestrinone-anti-gestrinone using arrays of high aspect ratio SU-8 nanopillars

In this paper, label-free biosensing for antibody screening by periodic lattices of high-aspect ratio SU-8 nano-pillars (BICELLs) is presented. As a demonstration, the determination of anti-gestrinone antibodies from whole rabbit serum is carried out, and for the first time, the dissociation constant (KD = 6 nM) of antigen-antibody recognition process is calculated using this sensing system. After gestrinone antigen immobilization on the BICELLs, the immunorecognition was performed. The cells were interrogated vertically by using micron spot size Fourier transform visible and IR spectrometry (FT-VIS-IR), and the dip wavenumber shift was monitored. The biosensing assay exhibited good reproducibility and sensitivity (LOD = 0.75 ng/mL).

Transpose return relation method for designing low noise oscillators

In this paper, a new linear method for optimizing compact low noise oscillators for RF/MW applications will be presented. The first part of this paper makes an overview of Leeson's model. It is pointed out, and it is demonstrates that the phase noise is always the same inside the oscillator loop. It is presented a general phase noise optimization method for reference plane oscillators. The new method uses Transpose Return Relations (RRT) as true loop gain functions for obtaining the optimum values of the elements of the oscillator, whatever scheme it has. With this method, oscillator topologies that have been designed and optimized using negative resistance, negative conductance or reflection coefficient methods, until now, can be studied like a loop gain method. Subsequently, the main disadvantage of Leeson's model is overcome, and now it is not only valid for loop gain methods, but it is valid for any oscillator topology. The last section of this paper lists the steps to be performed to use this method for proper phase noise optimization during the linear design process and before the final non-linear optimization. The power of the proposed RRT method is shown with its use for optimizing a common oscillator, which is later simulated using Harmonic Balance (HB) and manufactured. Then, the comparison of the linear, HB and measurements of the phase noise are compared.

Computational Methods for Identification of Vibrating Structures

System identification deals with the problem of building mathematical models of dynamical systems based on observed data from the system" [1]. In the context of civil engineering, the system refers to a large scale structure such as a building, bridge, or an offshore structure, and identification mostly involves the determination of modal parameters (the natural frequencies, damping ratios, and mode shapes). This paper presents some modal identification results obtained using a state-of-the-art time domain system identification method (data-driven stochastic subspace algorithms [2]) applied to the output-only data measured in a steel arch bridge. First, a three dimensional finite element model was developed for the numerical analysis of the structure using ANSYS. Modal analysis was carried out and modal parameters were extracted in the frequency range of interest, 0-10 Hz. The results obtained from the finite element modal analysis were used to determine the location of the sensors. After that, ambient vibration tests were conducted during April 23-24, 2009. The response of the structure was measured using eight accelerometers. Two stations of three sensors were formed (triaxial stations). These sensors were held stationary for reference during the test. The two remaining sensors were placed at the different measurement points along the bridge deck, in which only vertical and transversal measurements were conducted (biaxial stations). Point estimate and interval estimate have been carried out in the state space model using these ambient vibration measurements. In the case of parametric models (like state space), the dynamic behaviour of a system is described using mathematical models. Then, mathematical relationships can be established between modal parameters and estimated point parameters (thus, it is common to use experimental modal analysis as a synonym for system identification). Stable modal parameters are found using a stabilization diagram. Furthermore, this paper proposes a method for assessing the precision of estimates of the parameters of state-space models (confidence interval). This approach employs the nonparametric bootstrap procedure [3] and is applied to subspace parameter estimation algorithm. Using bootstrap results, a plot similar to a stabilization diagram is developed. These graphics differentiate system modes from spurious noise modes for a given order system. Additionally, using the modal assurance criterion, the experimental modes obtained have been compared with those evaluated from a finite element analysis. A quite good agreement between numerical and experimental results is observed.

Neural Processing Unit based on the Optical Bistable Properties of Semiconductor Laser Amplifiers

This paper analyzes the behavior of a neural processing unit based on the optical bistable properties of semiconductor laser amplifiers. A similar unit to the reported here was previously employed in the simulation of the mammalian retina. The main advantages of the present cell are its larger fan-out and the possibility of different responses according to the light wavelength impinging onto the cell. These properties allow to work with larger structures as well as to obtain different behaviors according to the light characteristics. This new approach gives a possible modeling closer to the real biological configurations. Moreover, a more detailed analysis of the basic cell internal behavior is reported

A function using cubic splines for the analysis of alpha--particles spectra from silicon detectors

A function based on the characteristics of the alpha-particle lines obtained with silicon semiconductor detectors and modi"ed by using cubic splines is proposed to parametrize the shape of the peaks. A reduction in the number of parameters initially considered in other proposals was carried out in order to improve the stability of the optimization process. It was imposed by the boundary conditions for the cubic splines term. This function was then able to describe peaks with highly anomalous shapes with respect to those expected from this type of detector. Some criteria were implemented to correctly determine the area of the peaks and their errors. Comparisons with other well-established functions revealed excellent agreement in the "nal values obtained from both "ts. Detailed studies on reliability of the "tting results were carried out and the application of the function is proposed. Although the aim was to correct anomalies in peak shapes, the peaks showing the expected shapes were also well "tted. Accordingly, the validity of the proposal is quite general in the analysis of alpha-particle spectrometry with semiconductor detectors.

Analysis of Magnetic Nozzles For Space Plasma Thrusters = Análisis de Toberas Magnéticas para Motores Espaciales de Plasma

Esta tesis presenta un análisis teórico del funcionamiento de toberas magnéticas para la propulsión espacial por plasmas. El estudio está basado en un modelo tridimensional y bi-fluido de la expansión supersónica de un plasma caliente en un campo magnético divergente. El modelo básico es ampliado progresivamente con la inclusión de términos convectivos dominantes de electrones, el campo magnético inducido por el plasma, poblaciones electrónicas múltiples a distintas temperaturas, y la capacidad de integrar el flujo en la región de expansión lejana. La respuesta hiperbólica del plasma es integrada con alta precisión y eficiencia haciendo uso del método de las líneas características. Se realiza una caracterización paramétrica de la expansión 2D del plasma en términos del grado de magnetización de iones, la geometría del campo magnético, y el perfil inicial del plasma. Se investigan los mecanismos de aceleración, mostrando que el campo ambipolar convierte la energía interna de electrones en energía dirigida de iones. Las corrientes diamagnéticas de Hall, que pueden hallarse distribuidas en el volumen del plasma o localizadas en una delgada capa de corriente en el borde del chorro, son esenciales para la operación de la tobera, ya que la fuerza magnética repulsiva sobre ellas es la encargada de confinar radialmente y acelerar axialmente el plasma. El empuje magnético es la reacción a esta fuerza sobre el motor. La respuesta del plasma muestra la separación gradual hacia adentro de los tubos de iones respecto de los magnéticos, lo cual produce la formación de corrientes eléctricas longitudinales y pone el plasma en rotación. La ganancia de empuje obtenida y las pérdidas radiales de la pluma de plasma se evalúan en función de los parámetros de diseño. Se analiza en detalle la separación magnética del plasma aguas abajo respecto a las líneas magnéticas (cerradas sobre sí mismas), necesaria para la aplicación de la tobera magnética a fines propulsivos. Se demuestra que tres teorías existentes sobre separación, que se fundamentan en la resistividad del plasma, la inercia de electrones, y el campo magnético que induce el plasma, son inadecuadas para la tobera magnética propulsiva, ya que producen separación hacia afuera en lugar de hacia adentro, aumentando la divergencia de la pluma. En su lugar, se muestra que la separación del plasma tiene lugar gracias a la inercia de iones y la desmagnetización gradual del plasma que tiene lugar aguas abajo, que permiten la separación ilimitada del flujo de iones respecto a las líneas de campo en condiciones muy generales. Se evalúa la cantidad de plasma que permanece unida al campo magnético y retorna hacia el motor a lo largo de las líneas cerradas de campo, mostrando que es marginal. Se muestra cómo el campo magnético inducido por el plasma incrementa la divergencia de la tobera magnética y por ende de la pluma de plasma en el caso propulsivo, contrariamente a las predicciones existentes. Se muestra también cómo el inducido favorece la desmagnetización del núcleo del chorro, acelerando la separación magnética. La hipótesis de ambipolaridad de corriente local, común a varios modelos de tobera magnética existentes, es discutida críticamente, mostrando que es inadecuada para el estudio de la separación de plasma. Una inconsistencia grave en la derivación matemática de uno de los modelos más aceptados es señalada y comentada. Incluyendo una especie adicional de electrones supratérmicos en el modelo, se estudia la formación y geometría de dobles capas eléctricas en el interior del plasma. Cuando dicha capa se forma, su curvatura aumenta cuanto más periféricamente se inyecten los electrones supratérmicos, cuanto menor sea el campo magnético, y cuanto más divergente sea la tobera magnética. El plasma con dos temperaturas electrónicas posee un mayor ratio de empuje magnético frente a total. A pesar de ello, no se encuentra ninguna ventaja propulsiva de las dobles capas, reforzando las críticas existentes frente a las propuestas de estas formaciones como un mecanismo de empuje. Por último, se presenta una formulación general de modelos autosemejantes de la expansión 2D de una pluma no magnetizada en el vacío. El error asociado a la hipótesis de autosemejanza es calculado, mostrando que es pequeño para plumas hipersónicas. Tres modelos de la literatura son particularizados a partir de la formulación general y comparados. Abstract This Thesis presents a theoretical analysis of the operation of magnetic nozzles for plasma space propulsion. The study is based on a two-dimensional, two-fluid model of the supersonic expansion of a hot plasma in a divergent magnetic field. The basic model is extended progressively to include the dominant electron convective terms, the plasma-induced magnetic field, multi-temperature electron populations, and the capability to integrate the plasma flow in the far expansion region. The hyperbolic plasma response is integrated accurately and efficiently with the method of the characteristic lines. The 2D plasma expansion is characterized parametrically in terms of the ion magnetization strength, the magnetic field geometry, and the initial plasma profile. Acceleration mechanisms are investigated, showing that the ambipolar electric field converts the internal electron energy into directed ion energy. The diamagnetic electron Hall current, which can be distributed in the plasma volume or localized in a thin current sheet at the jet edge, is shown to be central for the operation of the magnetic nozzle. The repelling magnetic force on this current is responsible for the radial confinement and axial acceleration of the plasma, and magnetic thrust is the reaction to this force on the magnetic coils of the thruster. The plasma response exhibits a gradual inward separation of the ion streamtubes from the magnetic streamtubes, which focuses the jet about the nozzle axis, gives rise to the formation of longitudinal currents and sets the plasma into rotation. The obtained thrust gain in the magnetic nozzle and radial plasma losses are evaluated as a function of the design parameters. The downstream plasma detachment from the closed magnetic field lines, required for the propulsive application of the magnetic nozzle, is investigated in detail. Three prevailing detachment theories for magnetic nozzles, relying on plasma resistivity, electron inertia, and the plasma-induced magnetic field, are shown to be inadequate for the propulsive magnetic nozzle, as these mechanisms detach the plume outward, increasing its divergence, rather than focusing it as desired. Instead, plasma detachment is shown to occur essentially due to ion inertia and the gradual demagnetization that takes place downstream, which enable the unbounded inward ion separation from the magnetic lines beyond the turning point of the outermost plasma streamline under rather general conditions. The plasma fraction that remains attached to the field and turns around along the magnetic field back to the thruster is evaluated and shown to be marginal. The plasmainduced magnetic field is shown to increase the divergence of the nozzle and the resulting plasma plume in the propulsive case, and to enhance the demagnetization of the central part of the plasma jet, contrary to existing predictions. The increased demagnetization favors the earlier ion inward separation from the magnetic field. The local current ambipolarity assumption, common to many existing magnetic nozzle models, is critically discussed, showing that it is unsuitable for the study of plasma detachment. A grave mathematical inconsistency in a well-accepted model, related to the acceptance of this assumption, is found out and commented on. The formation and 2D shape of electric double layers in the plasma expansion is studied with the inclusion of an additional suprathermal electron population in the model. When a double layer forms, its curvature is shown to increase the more peripherally suprathermal electrons are injected, the lower the magnetic field strength, and the more divergent the magnetic nozzle is. The twoelectron- temperature plasma is seen to have a greater magnetic-to-total thrust ratio. Notwithstanding, no propulsive advantage of the double layer is found, supporting and reinforcing previous critiques to their proposal as a thrust mechanism. Finally, a general framework of self-similar models of a 2D unmagnetized plasma plume expansion into vacuum is presented and discussed. The error associated with the self-similarity assumption is calculated and shown to be small for hypersonic plasma plumes. Three models of the literature are recovered as particularizations from the general framework and compared.

Low cost time division multiplexing of identical optical fibre ring intensity sensors

A time division multiplexing (TDM) array for passive multiplexing of identical fibre, optic intensity sensors has been demonstrated. Microbending loss sensors are introduced in fibre optic rings and pressure information is directly detected, demultiplexed and demodulated from the relative amplitude of the first two pulses produced on each ring. Several dynamic ranges from 6 dB to 14 dB are shown. A comparison between both fibre optic ring and Mach-Zehnder structure impulse responses is carried out and the consequences derived from second- and higher-order recirculating ring pulses are also evaluated. This technique can be applied to those TDM intensity sensing schemes which require low cost, high number of identical sensors, and suffer high element loss and undersirable intensity fluctuations at low frequencies.