In situ control of Si(100) and Ge(100) surface preparation for the heteroepitaxy of III-V solar cell architectures

Si(100) and Ge(100) substrates essential for subsequent III-V integration were studied in the hydrogen ambient of a metalorganic vapor phase epitaxy reactor. Reflectance anisotropy spectroscopy (RAS) enabled us to distinguish characteristic configurations of vicinal Si(100) in situ: covered with oxide, cleaned by thermal removing in H2, and terminated with monohydrides when cooling in H2 ambient. RAS measurements during cooling in H2 ambient after the oxide removal process revealed a transition from the clean to the monohydride terminated Si(100) surface dependent on process temperature. For vicinal Ge(100) we observed a characteristic RA spectrum after annealing and cooling in H2 ambient. According to results from X-ray photo electron spectroscopy and Fourier-transform infrared spectroscopy the spectrum corresponds to the monohydride terminated Ge(100) surface.

Open-atmosphere structural depth profiling of multilayer samples of photovoltaic interest using laser-induced plasma spectrometry

The present work aims to assess Laser-Induced Plasma Spectrometry (LIPS) as a tool for the characterization of photovoltaic materials. Despite being a well-established technique with applications to many scientific and industrial fields, so far LIPS is little known to the photovoltaic scientific community. The technique allows the rapid characterization of layered samples without sample preparation, in open atmosphere and in real time. In this paper, we assess LIPS ability for the determination of elements that are difficult to analyze by other broadly used techniques, or for producing analytical information from very low-concentration elements. The results of the LIPS characterization of two different samples are presented: 1) a 90 nm, Al-doped ZnO layer deposited on a Si substrate by RF sputtering and 2) a Te-doped GaInP layer grown on GaAs by Metalorganic Vapor Phase Epitaxy. For both cases, the depth profile of the constituent and dopant elements is reported along with details of the experimental setup and the optimization of key parameters. It is remarkable that the longest time of analysis was ∼10 s, what, in conjunction with the other characteristics mentioned, makes of LIPS an appealing technique for rapid screening or quality control whether at the lab or at the production line.

Back contacted emitter GaAs solar cells

A new device structure to improve the performance of concentrator GaAs solar cells is described and the first experimental results are reported. The reason for such an improvement relies on a drastic reduction of the shadowing and series resistance losses based on the possibility of back contacting the emitter region of the solar cell. The experimental results obtained with devices of these types, with a simplified structure, fabricated by liquid phase epitaxy, demonstrate the feasibility and correct operation of the proposed back contact of the emitter of the cells.

Modelización de los Procesos de Cristalización en Poliolefinas

“Por lo tanto, la cristalización de polímeros se supone, y en las teorías se describe a menudo, como un proceso de múltiples pasos con muchos aspectos físico-químicos y estructurales influyendo en él. Debido a la propia estructura de la cadena, es fácil entender que un proceso que es termodinámicamente forzado a aumentar su ordenamiento local, se vea obstaculizado geométricamente y, por tanto, no puede conducirse a un estado de equilibrio final. Como resultado, se forman habitualmente estructuras de no equilibrio con diferentes características dependiendo de la temperatura, presión, cizallamiento y otros parámetros físico-químicos del sistema”. Estas palabras, pronunciadas recientemente por el profesor Bernhard Wunderlich, uno de los mas relevantes fisico-quimicos que han abordado en las ultimas décadas el estudio del estado físico de las macromoléculas, adelantan lo que de alguna manera se explicita en esta memoria y constituyen el “leitmotiv” de este trabajo de tesis. El mecanismo de la cristalización de polímeros esta aun bajo debate en la comunidad de la física de polímeros y la mayoría de los abordajes experimentales se explican a través de la teoría LH. Esta teoría clásica debida a Lauritzen y Hoffman (LH), y que es una generalización de la teoría de cristalización de una molécula pequeña desde la fase de vapor, describe satisfactoriamente muchas observaciones experimentales aunque esta lejos de explicar el complejo fenómeno de la cristalización de polímeros. De hecho, la formulación original de esta teoría en el National Bureau of Standards, a comienzos de la década de los 70, sufrió varias reformulaciones importantes a lo largo de la década de los 80, buscando su adaptación a los hallazgos experimentales. Así nació el régimen III de cristalización que posibilita la creacion de nichos moleculares en la superficie y que dio pie al paradigma ofrecido por Sadler y col., para justificar los experimentos que se obtenian por “scattering” de neutrones y otras técnicas como la técnica de “droplets” o enfriamiento rapido. Por encima de todo, el gran éxito de la teoría radica en que explica la dependencia inversa entre el tamaño del plegado molecular y el subenfriamiento, definido este ultimo como el intervalo de temperatura que media entre la temperatura de equilibrio y la temperatura de cristalización. El problema concreto que aborda esta tesis es el estudio de los procesos de ordenamiento de poliolefinas con distinto grado de ramificacion mediante simulaciones numéricas. Los copolimeros estudiados en esta tesis se consideran materiales modelo de gran homogeneidad molecular desde el punto de vista de la distribución de tamaños y de ramificaciones en la cadena polimérica. Se eligieron estas poliolefinas debido al gran interes experimental en conocer el cambio en las propiedades fisicas de los materiales dependiendo del tipo y cantidad de comonomero utilizado. Además, son modelos sobre los que existen una ingente cantidad de información experimental, que es algo que preocupa siempre al crear una realidad virtual como es la simulación. La experiencia en el grupo Biophym es que los resultados de simulación deben de tener siempre un correlato mas o menos próximo experimental y ese argumento se maneja a lo largo de esta memoria. Empíricamente, se conoce muy bien que las propiedades físicas de las poliolefinas, en suma dependen del tipo y de la cantidad de ramificaciones que presenta el material polimérico. Sin embargo, tal como se ha explicado no existen modelos teóricos adecuados que expliquen los mecanismos subyacentes de los efectos de las ramas. La memoria de este trabajo es amplia por la complejidad del tema. Se inicia con una extensa introducción sobre los conceptos básicos de una macromolecula que son relevantes para entender el contenido del resto de la memoria. Se definen los conceptos de macromolecula flexible, distribuciones y momentos, y su comportamiento en disolución y fundido con los correspondientes parametros caracteristicos. Se pone especial énfasis en el concepto de “entanglement” o enmaranamiento por considerarse clave a la hora de tratar macromoléculas con una longitud superior a la longitud critica de enmaranamiento. Finaliza esta introducción con una reseña sobre el estado del arte en la simulación de los procesos de cristalización. En un segundo capitulo del trabajo se expone detalladamente la metodología usada en cada grupo de casos. En el primer capitulo de resultados, se discuten los estudios de simulación en disolución diluida para sistemas lineales y ramificados de cadena única. Este caso mas simple depende claramente del potencial de torsión elegido tal como se discute a lo largo del texto. La formación de los núcleos “babys” propuestos por Muthukumar parece que son consecuencia del potencial de torsión, ya que este facilita los estados de torsión mas estables. Así que se propone el análisis de otros potenciales que son igualmente utilizados y los resultados obtenidos sobre la cristalización, discutidos en consecuencia. Seguidamente, en un segundo capitulo de resultados se estudian moleculas de alcanos de cadena larga lineales y ramificados en un fundido por simulaciones atomisticas como un modelo de polietileno. Los resultados atomisticos pese a ser de gran detalle no logran captar en su totalidad los efectos experimentales que se observan en los fundidos subenfriados en su etapa previa al estado ordenado. Por esta razon se discuten en los capítulos 3 y 4 de resultados sistemas de cadenas cortas y largas utilizando dos modelos de grano grueso (CG-PVA y CG-PE). El modelo CG-PE se desarrollo durante la tesis. El uso de modelos de grano grueso garantiza una mayor eficiencia computacional con respecto a los modelos atomísticos y son suficientes para mostrar los fenómenos a la escala relevante para la cristalización. En todos estos estudios mencionados se sigue la evolución de los procesos de ordenamiento y de fusión en simulaciones de relajación isoterma y no isoterma. Como resultado de los modelos de simulación, se han evaluado distintas propiedades fisicas como la longitud de segmento ordenado, la cristalinidad, temperaturas de fusion/cristalizacion, etc., lo que permite una comparación con los resultados experimentales. Se demuestra claramente que los sistemas ramificados retrasan y dificultan el orden de la cadena polimérica y por tanto, las regiones cristalinas ordenadas decrecen al crecer las ramas. Como una conclusión general parece mostrarse una tendencia a la formación de estructuras localmente ordenadas que crecen como bloques para completar el espacio de cristalización que puede alcanzarse a una temperatura y a una escala de tiempo determinada. Finalmente hay que señalar que los efectos observados, estan en concordancia con otros resultados tanto teoricos/simulacion como experimentales discutidos a lo largo de esta memoria. Su resumen se muestra en un capitulo de conclusiones y líneas futuras de investigación que se abren como consecuencia de esta memoria. Hay que mencionar que el ritmo de investigación se ha acentuado notablemente en el ultimo ano de trabajo, en parte debido a las ventajas notables obtenidas por el uso de la metodología de grano grueso que pese a ser muy importante para esta memoria no repercute fácilmente en trabajos publicables. Todo ello justifica que gran parte de los resultados esten en fase de publicación. Abstract “Polymer crystallization is therefore assumed, and in theories often described, to be a multi step process with many influencing aspects. Because of the chain structure, it is easy to understand that a process which is thermodynamically forced to increase local ordering but is geometrically hindered cannot proceed into a final equilibrium state. As a result, nonequilibrium structures with different characteristics are usually formed, which depend on temperature, pressure, shearing and other parameters”. These words, recently written by Professor Bernhard Wunderlich, one of the most prominent researchers in polymer physics, put somehow in value the "leitmotiv "of this thesis. The crystallization mechanism of polymers is still under debate in the physics community and most of the experimental findings are still explained by invoking the LH theory. This classical theory, which was initially formulated by Lauritzen and Hoffman (LH), is indeed a generalization of the crystallization theory for small molecules from the vapor phase. Even though it describes satisfactorily many experimental observations, it is far from explaining the complex phenomenon of polymer crystallization. This theory was firstly devised in the early 70s at the National Bureau of Standards. It was successively reformulated along the 80s to fit the experimental findings. Thus, the crystallization regime III was introduced into the theory in order to explain the results found in neutron scattering, droplet or quenching experiments. This concept defines the roughness of the crystallization surface leading to the paradigm proposed by Sadler et al. The great success of this theory is the ability to explain the inverse dependence of the molecular folding size on the supercooling, the latter defined as the temperature interval between the equilibrium temperature and the crystallization temperature. The main scope of this thesis is the study of ordering processes in polyolefins with different degree of branching by using computer simulations. The copolymers studied along this work are considered materials of high molecular homogeneity, from the point of view of both size and branching distributions of the polymer chain. These polyolefins were selected due to the great interest to understand their structure– property relationships. It is important to note that there is a vast amount of experimental data concerning these materials, which is essential to create a virtual reality as is the simulation. The Biophym research group has a wide experience in the correlation between simulation data and experimental results, being this idea highly alive along this work. Empirically, it is well-known that the physical properties of the polyolefins depend on the type and amount of branches presented in the polymeric material. However, there are not suitable models to explain the underlying mechanisms associated to branching. This report is extensive due to the complexity of the topic under study. It begins with a general introduction to the basics concepts of macromolecular physics. This chapter is relevant to understand the content of the present document. Some concepts are defined along this section, among others the flexibility of macromolecules, size distributions and moments, and the behavior in solution and melt along with their corresponding characteristic parameters. Special emphasis is placed on the concept of "entanglement" which is a key item when dealing with macromolecules having a molecular size greater than the critical entanglement length. The introduction finishes with a review of the state of art on the simulation of crystallization processes. The second chapter of the thesis describes, in detail, the computational methodology used in each study. In the first results section, we discuss the simulation studies in dilute solution for linear and short chain branched single chain models. The simplest case is clearly dependent on the selected torsion potential as it is discussed throughout the text. For example, the formation of baby nuclei proposed by Mutukhumar seems to result from the effects of the torsion potential. Thus, we propose the analysis of other torsion potentials that are also used by other research groups. The results obtained on crystallization processes are accordingly discussed. Then, in a second results section, we study linear and branched long-chain alkane molecules in a melt by atomistic simulations as a polyethylene-like model. In spite of the great detail given by atomistic simulations, they are not able to fully capture the experimental facts observed in supercooled melts, in particular the pre-ordered states. For this reason, we discuss short and long chains systems using two coarse-grained models (CG-PVA and CG-PE) in section 3 and 4 of chapter 2. The CG-PE model was developed during the thesis. The use of coarse-grained models ensures greater computational efficiency with respect to atomistic models and is enough to show the relevant scale phenomena for crystallization. In all the analysis we follow the evolution of the ordering and melting processes by both isothermal and non isothermal simulations. During this thesis we have obtained different physical properties such as stem length, crystallinity, melting/crystallization temperatures, and so on. We show that branches in the chains cause a delay in the crystallization and hinder the ordering of the polymer chain. Therefore, crystalline regions decrease in size as branching increases. As a general conclusion, it seems that there is a tendency in the macromolecular systems to form ordered structures, which can grown locally as blocks, occupying the crystallization space at a given temperature and time scale. Finally it should be noted that the observed effects are consistent with both, other theoretical/simulation and experimental results. The summary is provided in the conclusions chapter along with future research lines that open as result of this report. It should be mentioned that the research work has speeded up markedly in the last year, in part because of the remarkable benefits obtained by the use of coarse-grained methodology that despite being very important for this thesis work, is not easily publishable by itself. All this justify that most of the results are still in the publication phase.

An eco-friendly way to fire retardant flexible polyurethane foam: layer-by-layer assembly of fully bio-based substances

The objective of the present study is to develop fully renewable and environmentally benign techniques for improving the fire safety of flexible polyurethane foams (PUFs). A multilayered coating made from cationic chitosan (CS) and anionic alginate (AL) was deposited on PUFs through layer-by-layer assembly. This coating system exhibits a slight influence on the thermal stability of PUF, but significantly improves the char formation during combustion. Cone calorimetry reveals that 10 CS-AL bilayers (only 5.7% of the foams weight) lead to a 66% and 11% reduction in peak heat release rate and total heat release, respectively, compared with those of the uncoated control. The notable decreased fire hazards of PUF are attributed to the CS-AL coatings being beneficial to form an insulating protective layer on the surface of burning materials that inhibits the oxygen and heat permeation and slows down the flammable gases in the vapor phase, and thereby improves the flame resistance. This water-based, environmentally benign natural coating will stimulate further efforts in improving fire safety for a variety of polymer substrates.