Nanoimprinted diffraction gratings for crystalline silicon solar cells: implementation, characterization and simulation

Light trapping is becoming of increasing importance in crystalline silicon solar cells as thinner wafers are used to reduce costs. In this work, we report on light trapping by rear-side diffraction gratings produced by nano-imprint lithography using interference lithography as the mastering technology. Gratings fabricated on crystalline silicon wafers are shown to provide significant absorption enhancements. Through a combination of optical measurement and simulation, it is shown that the crossed grating provides better absorption enhancement than the linear grating, and that the parasitic reflector absorption is reduced by planarizing the rear reflector, leading to an increase in the useful absorption in the silicon. Finally, electro-optical simulations are performed of solar cells employing the fabricated grating structures to estimate efficiency enhancement potential.

Evolution of microstructure, macrotexture and mechanical properties of commercially pure Ti during ECAP-conform processing and drawing

Long-length ultrafine-grained (UFG) Ti rods are produced by equal-channel angular pressing via the conform scheme (ECAP-C) at 200 °C, which is followed by drawing at 200 °C. The evolution of microstructure, macrotexture, and mechanical properties (yield strength, ultimate tensile strength, failure stress, uniform elongation, elongation to failure) of pure Ti during this thermo-mechanical processing is studied. Special attention is also paid to the effect of microstructure on the mechanical behavior of the material after macrolocalization of plastic flow. The number of ECAP-C passes varies in the range of 1–10. The microstructure is more refined with increasing number of ECAP-C passes. Formation of homogeneous microstructure with a grain/subgrain size of 200 nm and its saturation after 6 ECAP-C passes are observed. Strength properties increase with increasing number of ECAP passes and saturate after 6 ECAP-C passes to a yield strength of 973 MPa, an ultimate tensile strength of 1035 MPa, and a true failure stress of 1400 MPa (from 625, 750, and 1150 MPa in the as-received condition). The true strain at failure failure decreases after ECAP-C processing. The reduction of area and true strain to failure values do not decrease after ECAP-C processing. The sample after 6 ECAP-C passes is subjected to drawing at 200¯C resulting in reduction of a grain/subgrain size to 150 nm, formation of (10 1¯0) fiber texture with respect to the rod axis, and further increase of the yield strength up to 1190 MPa, the ultimate tensile strength up to 1230 MPa and the true failure stress up to 1600 MPa. It is demonstrated that UFG CP Ti has low resistance to macrolocalization of plastic deformation and high resistance to crack formation after necking.

Stability and mechanical evaluation of bovine pericardium cross-linked with polyurethane prepolymer in aqueous medium

The present study investigates the potential use of non-catalyzed water-soluble blocked polyurethane prepolymer (PUP) as a bifunctional cross-linker for collagenous scaffolds. The effect of concentration (5, 10, 15 and 20%), time (4, 6, 12 and 24 h), medium volume (50, 100, 200 and 300%) and pH (7.4, 8.2, 9 and 10) over stability, microstructure and tensile mechanical behavior of acellular pericardial matrix was studied. The cross-linking index increased up to 81% while the denaturation temperature increased up to 12 °C after PUP crosslinking. PUP-treated scaffold resisted the collagenase degradation (0.167 ± 0.14 mmol/g of liberated amine groups vs. 598 ± 60 mmol/g for non-cross-linked matrix). The collagen fiber network was coated with PUP while viscoelastic properties were altered after cross-linking. The treatment of the pericardial scaffold with PUP allows (i) different densities of cross-linking depending of the process parameters and (ii) tensile properties similar to glutaraldehyde method.

Latent hardening size effect in small-scale plasticity

We aim at understanding the multislip behaviour of metals subject to irreversible deformations at small-scales. By focusing on the simple shear of a constrained single-crystal strip, we show that discrete Dislocation Dynamics (DD) simulations predict a strong latent hardening size effect, with smaller being stronger in the range [1.5 µm, 6 µm] for the strip height. We attempt to represent the DD pseudo-experimental results by developing a flow theory of Strain Gradient Crystal Plasticity (SGCP), involving both energetic and dissipative higher-order terms and, as a main novelty, a strain gradient extension of the conventional latent hardening. In order to discuss the capability of the SGCP theory proposed, we implement it into a Finite Element (FE) code and set its material parameters on the basis of the DD results. The SGCP FE code is specifically developed for the boundary value problem under study so that we can implement a fully implicit (Backward Euler) consistent algorithm. Special emphasis is placed on the discussion of the role of the material length scales involved in the SGCP model, from both the mechanical and numerical points of view.

Mechanical Degradation of Tungsten Alloys at Extreme Temperatures in Vacuum and Oxidation Atmospheres

Mechanical degradation of tungsten alloys at extreme temperatures in vacuum and oxidation atmospheres.

Effect of fire on the microstructure and mechanical response of structural steels for building construction

The research is an exhaustive study of the microstructure and of the stress-strain curves of structural steel S460N at temperatures typical of a fire. It includes a fractographic study of the fracture suifaces of cylindrical specimens, tensile tested at different fire scenarios, explaining the relationship between the failure micromechanisms and temperature. The paper ends with the comparison between the experimentally found strain-stress curves with that one's proposed by the EUROCODE EC3, resulting that in the case of steel S460N these are on the side ofsafety.

Damage mechanisms of 3D woven hybrid composites in tension. Testing, inspection and simulation

Delamination reduces the strenght of the composites, mainly in compression. Several methods exist to overcome this problem, but they are either not feasible for large scale production or too expensive. 3D composites are a promising solution.

Fracture micromechanisms and residual stresses of a highly resistant duplex stainless steel

The paper presents some preliminary results of an ongoing research intended to qualify a highly resistant duplex stainless steel wire as prestressing steel and, gets on insight on (he wires' fracture micromechanism and residual stresses field. SEM fractographic analysis of the stainless steel wires indicates an anisotropic fracture behavior in tension, in presence of surface flaws, attributed to the residual stresses generated through the fabrication process. The residual stresses magnitude influences the damage tolerance, its knowledge being a key issue in designating/qualifying the wires as prestressing steels.

Agent-based modeling and simulation for the design of the future european Air Traffic Management system: the experience of CASSIOPEIA

The SESAR (Single European Sky ATM Research) program is an ambitious re-search and development initiative to design the future European air traffic man-agement (ATM) system. The study of the behavior of ATM systems using agent-based modeling and simulation tools can help the development of new methods to improve their performance. This paper presents an overview of existing agent-based approaches in air transportation (paying special attention to the challenges that exist for the design of future ATM systems) and, subsequently, describes a new agent-based approach that we proposed in the CASSIOPEIA project, which was developed according to the goals of the SESAR program. In our approach, we use agent models for different ATM stakeholders, and, in contrast to previous work, our solution models new collaborative decision processes for flow traffic management, it uses an intermediate level of abstraction (useful for simulations at larger scales), and was designed to be a practical tool (open and reusable) for the development of different ATM studies. It was successfully applied in three stud-ies related to the design of future ATM systems in Europe.

Proposal for a semantic hierarchy of terminological metaphors in science and technology

Cognitive linguistics is considered as one of the most appropriate approaches to the study of scientific and technical language formation and development, where metaphor is accepted to play an essential role. This paper, based on the Cognitive Theory of Metaphor, takes as the starting point the terminological metaphors established in the research project METACITEC(Note 1), which was developed with the purpose of unfolding constitutive metaphors and their function in the language of science and technology. After the analysis of metaphorical terms and using a mixed corpus from the fields of Agriculture, Geology, Mining, Metallurgy, and other related technical fields, this study presents a proposal for a hierarchy of the selected metaphors underlying the scientific conceptual system, based on the semantic distance found in the projection from the source domain to the target domain. We argue that this semantic distance can be considered as an important parameter to take into account in order to establish the metaphoricity of science and technology metaphorical terms. The findings contribute to expand on the CTM stance that metaphor is a matter of cognition by reviewing the abstract-concrete conceptual relationship between the target and source domains, and to determine the role of human creativity and imagination in the language of science and technology configuration

Recent progress in research on tungsten materials for nuclear fusion applications in Europe

The current magnetic confinement nuclear fusion power reactor concepts going beyond ITER are based on assumptions about the availability of materials with extreme mechanical, heat, and neutron load capacity. In Europe, the development of such structural and armour materials together with the necessary production, machining, and fabrication technologies is pursued within the EFDA long-term fusion materials programme. This paper reviews the progress of work within the programme in the area of tungsten and tungsten alloys. Results, conclusions, and future projections are summarized for each of the programme´s main subtopics, which are: (1) fabrication, (2) structural W materials, (3) W armour materials, and (4) materials science and modelling. It gives a detailed overview of the latest results on materials research, fabrication processes, joining options, high heat flux testing, plasticity studies, modelling, and validation experiments.

Analysis of crystallographic slip and grain boundary sliding in a Ti-45Al-2Nb-2Mn (at%)-0.8 vol%TiB2 alloy by high temperature in situ mechanical testing

This work aims to contribute to a further understanding of the fundamentals of crystallographic slip and grain boundary sliding in the γ-TiAl Ti–45Al–2Nb–2Mn (at%)–0.8 vol%TiB2 intermetallic alloy, by means of in situ high-temperature tensile testing combined with electron backscatter diffraction (EBSD). Several microstructures, containing different fractions and sizes of lamellar colonies and equiaxed γ-grains, were fabricated by either centrifugal casting or powder metallurgy, followed by heat treatment at 1300 °C and furnace cooling. in situ tensile and tensile-creep experiments were performed in a scanning electron microscope (SEM) at temperatures ranging from 580 °C to 700 °C. EBSD was carried out in selected regions before and after straining. Our results suggest that, during constant strain rate tests, true twin γ/γ interfaces are the weakest barriers to dislocations and, thus, that the relevant length scale might be influenced by the distance between non-true twin boundaries. Under creep conditions both grain/colony boundary sliding (G/CBS) and crystallographic slip are observed to contribute to deformation. The incidence of boundary sliding is particularly high in γ grains of duplex microstructures. The slip activity during creep deformation in different microstructures was evaluated by trace analysis. Special emphasis was placed in distinguishing the compliance of different slip events with the Schmid law with respect to the applied stress.

Complejidad Esencial: Un argumento por la complementariedad entre ciencia y sensibilidad = Essential Complexity: An argument for complementarity between science and sensibility

Esta investigación recoge un cúmulo de intereses en torno a un modo de generar arquitectura muy específico: La producción de objetos con una forma subyacente no apriorística. Los conocimientos expuestos se apoyan en condiciones del pensamiento reciente que impulsan la ilusión por alimentar la fuente creativa de la arquitectura con otros campos del saber. Los tiempos del conocimiento animista sensible y el conocimiento objetivo de carácter científico son correlativos en la historia pero casi nunca han sido sincrónicos. Representa asimismo un intento por aunar los dos tipos de conocimiento retomando la inercia que ya se presentía a comienzos del siglo XX. Se trata por tanto, de un ensayo sobre la posible anulación de la contraposición entre estos dos mundos para pasar a una complementariedad entre ambos en una sola visión conjunta compartida. Como meta final de esta investigación se presenta el desarrollo de un sistema crítico de análisis para los objetos arquitectónicos que permita una diferenciación entre aquellos que responden a los problemas de manera completa y sincera y aquellos otros que esconden, bajo una superficie consensuada, la falta de un método resolutivo de la complejidad en el presente creativo. La Investigación observa tres grupos de conocimiento diferenciados agrupados en sus capítulos correspondientes: El primer capítulo versa sobre el Impulso Creador. En él se define la necesidad de crear un marco para el individuo creador, aquel que independientemente de las fuerzas sociales del momento presiente que existe algo más allá que está sin resolver. Denominamos aquí “creador rebelde” a un tipo de personaje reconocible a lo largo de la Historia como aquel capaz de reconocer los cambios que ese operan en su presente y que utiliza para descubrir lo nuevo y acercarse algo al origen creativo. En el momento actual ese tipo de personaje es el que intuye o ya ha intuido hace tiempo la existencia de una complejidad creciente no obviable en el pensamiento de este tiempo. El segundo capítulo desarrolla algunas Propiedades de Sistemas de actuación creativa. En él se muestra una investigación que desarrolla un marco de conocimientos científicos muy específicos de nuestro tiempo que la arquitectura, de momento, no ha absorbido ni refleja de manera directa en su manera de crear. Son temas de presencia casi ya mundana en la sociedad pero que se resisten a ser incluidos en los procesos creativos como parte de la conciencia. La mayoría de ellos hablan de precisión, órdenes invisibles, propiedades de la materia o la energía tratados de manera objetiva y apolítica. La meta final supone el acercamiento e incorporación de estos conceptos y propiedades a nuestro mundo sensible unificándolos indisociablemente bajo un solo punto de vista. El último capítulo versa sobre la Complejidad y su capacidad de reducción a lo esencial. Aquí se muestran, a modo de conclusiones, la introducción de varios conceptos para el desarrollo de un sistema crítico hacia la arquitectura de nuestro tiempo. Entre ellos, el de Complejidad Esencial, definido como aquella de carácter inevitable a la hora de responder la arquitectura a los problemas y solicitaciones crecientes a los que se enfrenta en el presente. La Tesis mantiene la importancia de informar sobre la imposibilidad en el estado actual de las cosas de responder de manera sincera con soluciones de carácter simplista y la necesidad, por tanto, de soluciones necesarias de carácter complejo. En este sentido se define asimismo el concepto de Forma Subyacente como herramienta crítica para poder evaluar la respuesta de cada arquitectura y poder tener un sistema y visión crítica sobre lo que es un objeto consistente frente a la situación a la que se enfrenta. Dicha forma subyacente se define como aquella manera de entender conjuntamente y de manera sincrónica aquello que percibimos de manera sensible inseparable de las fuerzas ocultas, creativas, tecnológicas, materiales y energéticas que sustentan la definición y entendimiento de cualquier objeto construido. ABSTRACT This research includes a cluster of interests around a specific way to generate architecture: The production of objects without an a priori underlying form. The knowledge presented is based on current conditions of thought promoting the illusion to feed the creative source of architecture with other fields of knowledge. The sensible animist knowledge and objective scientific knowledge are correlative in history but have rarely been synchronous. This research is also an attempt to combine both types of knowledge to regain the inertia already sensed in the early twentieth century. It is therefore an essay on the annulment of the opposition between these two worlds to move towards complementarities of both in a single shared vision. The ultimate goal of this research is to present the development of a critical analysis system for architectural objects that allows differentiation between those who respond to the problems sincerely and those who hide under an agreed appearance, the lack of a method for solving the complexity of the creative present. The research observes three distinct groups of knowledge contained in their respective chapters: The first chapter deals with the Creative Impulse. In it is defined the need to create a framework for the creative individual who, regardless of the current social forces, forebodes that there is something hidden beyond which is still unresolved. We define the "rebel creator" as a kind of person existing throughout history who is able to recognize the changes operating in its present and use them to discover something new and get closer to the origin of creation. At present, this type of character is the one who intuits the existence of a non obviable increasing complexity in society and thought. The second chapter presents some systems, and their properties, for creative performance. It describes the development of a framework composed of current scientific knowledge that architecture has not yet absorbed or reflected directly in her procedures. These are issues of common presence in society but are still reluctant to be included in the creative processes even if they already belong to the collective consciousness. Most of them talk about accuracy, invisible orders, properties of matter and energy, always treated from an objective and apolitical perspective. The ultimate goal pursues the approach and incorporation of these concepts and properties to the sensible world, inextricably unifying all under a single point of view. The last chapter deals with complexity and the ability to reduce it to the essentials. Here we show, as a conclusion, the introduction of several concepts to develop a critical approach to analyzing the architecture of our time. Among them, the concept of Essential Complexity, defined as one that inevitably arises when architecture responds to the increasing stresses that faces today. The thesis maintains the importance of reporting, in the present state of things, the impossibility to respond openly with simplistic solutions and, therefore, the need for solutions to complex character. In this sense, the concept of Underlying Form is defined as a critical tool to evaluate the response of each architecture and possess a critical system to clarify what is an consistent object facing a certain situation. The underlying form is then defined as a way to synchronously understand what we perceive sensitively inseparable from the hidden forces of creative, technological, material and energetic character that support the definition and understanding of any constructed object.

Modeling and Simulation of Upper Brachial Plexus Injury

This article presents the first musculoskeletal model and simulation of upper plexus brachial injury. From this model is possible to analyse forces and movement ranges in order to develop a robotic exoskeleton to improve rehabilitation. The software that currently exists for musculoskeletal modeling is varied and most have advanced features for proper analysis and study of motion simulations. Whilst more powerful computer packages are usually expensive, there are other free and open source packages available which offer different tools to perform animations and simulations and which obtain forces and moments of inertia. Among them, Musculoskeletal Modeling Software was selected to construct a model of the upper limb, which has 7 degrees of freedom and 10 muscles. These muscles are important for two of the movements simulated in this article that are part of the post-surgery rehabilitation protocol. We performed different movement animations which are made using the inertial measurement unit to capture real data from movements made by a human being. We also performed the simulation of forces produced in elbow flexion-extension and arm abduction-adduction of a healthy subject and one with upper brachial plexus injury in a postoperative state to compare the force that is capable of being produced in both cases.