Modeling of the Division Point of Different Propagation Mechanisms in the Near-Region Within Arched Tunnels

An accurate characterization of the near-region propagation of radio waves inside tunnels is of practical importance for the design and planning of advanced communication systems. However, there has been no consensus yet on the propagation mechanism in this region. Some authors claim that the propagation mechanism follows the free space model, others intend to interpret it by the multi-mode waveguide model. This paper clarifies the situation in the near-region of arched tunnels by analytical modeling of the division point between the two propagation mechanisms. The procedure is based on the combination of the propagation theory and the three-dimensional solid geometry. Three groups of measurements are employed to verify the model in different tunnels at different frequencies. Furthermore, simplified models for the division point in five specific application situations are derived to facilitate the use of the model. The results in this paper could help to deepen the insight into the propagation mechanism within tunnel environments.

Modulation-mode Assignment for SVD-assisted Multiuser MIMO Systems with Correlation.

Multiuser multiple-input multiple-output (MIMO) downlink (DL) transmission schemes experience both multiuser interference as well as inter-antenna interference. The singular value decomposition provides an appropriate mean to process channel information and allows us to take the individual user’s channel characteristics into account rather than treating all users channels jointly as in zero-forcing (ZF) multiuser transmission techniques. However, uncorrelated MIMO channels has attracted a lot of attention and reached a state of maturity. By contrast, the performance analysis in the presence of antenna fading correlation, which decreases the channel capacity, requires substantial further research. The joint optimization of the number of activated MIMO layers and the number of bits per symbol along with the appropriate allocation of the transmit power shows that not necessarily all user-specific MIMO layers has to be activated in order to minimize the overall BER under the constraint of a given fixed data throughput.

Modulation-mode Assignment in SVD-assisted Multiuser MIMO-OFDM Systems

In order to comply with the demand on increasing available data rates in particular in wireless technologies, systems with multiple transmit and receive antennas, also called MIMO (multiple-input multiple-output) systems, have become indispensable for future generations of wireless systems. Due to the strongly increasing demand in high-data rate transmission systems, frequency non-selective MIMO links have reached a state of maturity and frequency selective MIMO links are in the focus of interest. In this field, the combination of MIMO transmission and OFDM (orthogonal frequency division multiplexing) can be considered as an essential part of fulfilling the requirements of future generations of wireless systems. However, single-user scenarios have reached a state of maturity. By contrast multiple users’ scenarios require substantial further research, where in comparison to ZF (zero-forcing) multiuser transmission techniques, the individual user’s channel characteristics are taken into consideration in this contribution. The performed joint optimization of the number of activated MIMO layers and the number of transmitted bits per subcarrier along with the appropriate allocation of the transmit power shows that not necessarily all user-specific MIMO layers per subcarrier have to be activated in order to minimize the overall BER under the constraint of a given fixed data throughput

WiMAX,Technology and Market.

Wireless communication is the transfer of information from one place to another without using wires. From the earliest times, humans have felt the need to develop techniques of remote communication. From this need arose the smoke signals, communication by sun reflection in mirrors and so on. But today the telecommunications electronic devices such as telephone, television, radio or computer. Radio and television are used for one-way communication. Telephone and computer are used for two-way communication. In wireless networks there is almost unlimited mobility, we can access the network almost anywhere or anytime. In wired networks we have the restriction of using the services in fixed area services. The demand of the wireless is increasing very fast; everybody wants broadband services anywhere anytime. WiMAX (Worldwide Interoperability for Microwave Access) is a broadband wireless technology based on IEEE 802.16-2004 and IEEE 802.16e-2005 that appears to solve this demand. WIMAX is a system that allows wireless data transmission in areas of up to 48 km of radius. It is designed as a wireless alternative to ADSL and a way to connect nodes in wireless metropolitan areas network. Unlike wireless systems that are limited in most cases, about 100 meter, providing greater coverage and more bandwidth. WIMAX promises to achieve high data transmission rates over large areas with a great amount of users. This alternative to the networks of broadband access common as DSL o Wi-Fi, can give broadband access to places quickly to rural areas and developing areas around the world. This paper is a study of WIMAX technology and market situation. First, the paper is responsible for explaining the technical aspects of WIMAX. For this gives an overview of WIMAX standards, physical layer, MAC layer and WiMAX, Technology and Market Beijing University of Post and Telecommunications 2 WIMAX network architecture. Second, the paper address the issue of market in which provides an overview of development and deployment of WIMAX to end the future development trend of WIMAX is addressed. RESUMEN: Por comunicaciones inalámbricas se entiende la transferencia de información desde un lugar a otro sin la necesidad de un soporte físico como es por ejemplo el cable. Por lo que remontándose a los principios de la existencia del ser humano, nos damos cuenta de que el ser humano siempre ha sentido la necesidad de desarrollar técnicas para lograr comunicarse a distancia con sus semejantes. De dicha necesidad, surgieron técnicas tan ancestrales como puede ser la comunicación mediante señales de humo o por reflexión de los rayos solares en espejos entre otras. La curiosidad del ser humano y la necesidad de comunicarse a distancia fue la que llevó a Alexander Graham Bell a inventar el teléfono en 1876. La aparición de un dispositivo que permitía comunicarse a distancia permitiendo escuchar la voz de aquella persona con la que se quería hablar, supuso una revolución no solo en el panorama tecnológico, si no también en el panorama social. Pues a parte de permitir comunicaciones a larga distancia, solventó el problema de la comunicación en “tiempo real”. A raíz de este invento, la tecnología en materia de comunicación ha ido avanzando significativamente, más concretamente en lo referido a las comunicaciones inalámbricas. En 1973 se realizó la primera llamada desde un terminal móvil aunque no fue hasta 1983 cuando se empezó a comercializar dicho terminal, lo que supuso un cambio de hábitos y costumbres para la sociedad. Desde la aparición del primer móvil el crecimiento del mercado ha sido exponencial, lo que ha repercutido en una demanda impensable de nuevas aplicaciones integradas en dichos dispositivos móviles que satisfagan las necesidades que día a día autogenera la sociedad. Tras conseguir realizar llamadas a larga distancia de forma inalámbrica, el siguiente paso fue la creación de los SMS (Short Message System) lo que supuso una nueva revolución además de abaratar costes al usuario a la hora de comunicarse. Pero el gran reto para la industria de las comunicaciones móviles surgió con la aparición de internet. Todo el mundo sentía la necesidad de poder conectarse a esa gran base de datos que es internet en cualquier parte y en cualquier momento. Las primeras conexiones a internet desde dispositivos móviles se realizaron a través de la tecnología WAP (Wireless Application Protocol) hasta la aparición de la tecnología GPRS que permitía la conexión mediante protocolo TCP/IP. A partir de estas conexiones han surgido otras tecnologías, como EDGE, HSDPA, etc., que permitían y permiten la conexión a internet desde dispositivos móviles. Hoy en día la demanda de servicios de red inalámbrica crece de forma rápida y exponencial, todo el mundo quiere servicios de banda ancha en cualquier lugar y en cualquier momento. En este documento se analiza la tecnología WiMAX ( Worldwide Interoperability for Microwave Access) que es una tecnología de banda ancha basada en el estándar IEEE 802.16 creada para brindar servicios a la demanda emergente en la banda ancha desde un punto de vista tecnológico, donde se da una visión de la parte técnica de la tecnología; y desde el punto de vista del mercado, donde se analiza el despliegue y desarrollo de la tecnología desde el punto de vista de negocio. WiMAX es una tecnología que permite la transmisión inalámbrica de datos en áreas de hasta 48Km de radio y que está diseñada como alternativa inalámbrica para ADSL y para conectar nodos de red inalámbrica en áreas metropolitanas. A diferencia de los sistemas inalámbricos existentes que están limitados en su mayoría a unos cientos de metros, WiMAX ofrece una mayor cobertura y un mayor ancho de banda que permita dar soporte a nuevas aplicaciones, además de alcanzar altas tasas de transmisión de datos en grandes áreas con una gran cantidad de usuarios. Se trata de una alternativa a las redes de acceso de banda ancha como DSL o Wi-Fi, que puede dar acceso de banda ancha a lugares tales como zonas rurales o zonas en vías de desarrollo por todo el mundo con rapidez. Existen dos tecnologías de WiMAX, WiMAX fijo (basado en el estándar IEEE 802.16d-2004) y WiMAX móvil (basado en el estándar IEEE 802.16e-2005). La tecnología fija está diseñada para comunicaciones punto a multipunto, mientras que la fija lo está para comunicaciones multipunto a multipunto. WiMAX móvil se basa en la tecnología OFDM que ofrece ventajas en términos de latencia, eficiencia en el uso del espectro y soporte avanzado para antenas. La modulación OFDM es muy robusta frente al multitrayecto, que es muy habitual en los canales de radiodifusión, frente al desvanecimiento debido a las condiciones meteorológicas y frente a las interferencias de RF. Una vez creada la tecnología WiMAX, poseedora de las características idóneas para solventar la demanda del mercado, ha de darse el siguiente paso, hay que convencer a la industria de las telecomunicaciones de que dicha tecnología realmente es la solución para que apoyen su implantación en el mercado de la banda ancha para las redes inalámbricas. Es aquí donde entra en juego el estudio del mercado que se realiza en este documento. WiMAX se enfrenta a un mercado exigente en el que a parte de tener que dar soporte a la demanda técnica, ha de ofrecer una rentabilidad económica a la industria de las comunicaciones móviles y más concretamente a las operadoras móviles que son quienes dentro del sector de las telecomunicaciones finalmente han de confiar en la tecnología para dar soporte a sus usuarios ya que estos al fin y al cabo lo único que quieren es que su dispositivo móvil satisfaga sus necesidades independientemente de la tecnología que utilicen para tener acceso a la red inalámbrica de banda ancha. Quizás el mayor problema al que se ha enfrentado WiMAX haya sido la situación económica en la que se encuentra el mundo. WiMAX a comenzado su andadura en uno de los peores momentos, pero aun así se presenta como una tecnología capaz de ayudar al mundo a salir hacia delante en estos tiempos tan duros. Finalmente se analiza uno de los debates existentes hoy en día en el sector de las comunicaciones móviles, WiMAX vs. LTE. Como se puede observar en el documento realmente una tecnología no saldrá victoriosa frente a la otra, si no que ambas tecnologías podrán coexistir y trabajar de forma conjunta.

On the use of discrete cosine transforms for multicarrier communications

In this correspondence, the conditions to use any kind of discrete cosine transform (DCT) for multicarrier data transmission are derived. The symmetric convolution-multiplication property of each DCT implies that when symmetric convolution is performed in the time domain, an element-by-element multiplication is performed in the corresponding discrete trigonometric domain. Therefore, appending symmetric redun-dancy (as prefix and suffix) into each data symbol to be transmitted, and also enforcing symmetry for the equivalent channel impulse response, the linear convolution performed in the transmission channel becomes a symmetric convolution in those samples of interest. Furthermore, the channel equalization can be carried out by means of a bank of scalars in the corresponding discrete cosine transform domain. The expressions for obtaining the value of each scalar corresponding to these one-tap per subcarrier equalizers are presented. This study is completed with several computer simulations in mobile broadband wireless communication scenarios, considering the presence of carrier frequency offset (CFO). The obtained results indicate that the proposed systems outperform the standardized ones based on the DFT.

An optimized QoS scheme for IMS-NEMO in heterogeneous networks

The network mobility (NEMO) is proposed to support the mobility management when users move as a whole. In IP Multimedia Subsystem (IMS), the individual Quality of Service (QoS) control for NEMO results in excessive signaling cost. On the other hand, current QoS schemes have two drawbacks: unawareness of the heterogeneous wireless environment and inefficient utilization of the reserved bandwidth. To solve these problems, we present a novel heterogeneous bandwidth sharing (HBS) scheme for QoS provision under IMS-based NEMO (IMS-NEMO). The HBS scheme selects the most suitable access network for each session and enables the new coming non-real-time sessions to share bandwidth with the Variable Bit Rate (VBR) coded media flows. The modeling and simulation results demonstrate that the HBS can satisfy users' QoS requirement and obtain a more efficient use of the scarce wireless bandwidth.

Structural health monitoring network system with wireless communications inside closed aerospace structures

Structural Health Monitoring (SHM) requires integrated "all in one" electronic devices capable of performing analysis of structural integrity and on-board damage detection in aircraft?s structures. PAMELA III (Phased Array Monitoring for Enhanced Life Assessment, version III) SHM embedded system is an example of this device type. This equipment is capable of generating excitation signals to be applied to an array of integrated piezoelectric Phased Array (PhA) transducers stuck to aircraft structure, acquiring the response signals, and carrying out the advanced signal processing to obtain SHM maps. PAMELA III is connected with a host computer in order to receive the configuration parameters and sending the obtained SHM maps, alarms and so on. This host can communicate with PAMELA III through an Ethernet interface. To avoid the use of wires where necessary, it is possible to add Wi-Fi capabilities to PAMELA III, connecting a Wi-Fi node working as a bridge, and to establish a wireless communication between PAMELA III and the host. However, in a real aircraft scenario, several PAMELA III devices must work together inside closed structures. In this situation, it is not possible for all PAMELA III devices to establish a wireless communication directly with the host, due to the signal attenuation caused by the different obstacles of the aircraft structure. To provide communication among all PAMELA III devices and the host, a wireless mesh network (WMN) system has been implemented inside a closed aluminum wingbox. In a WMN, as long as a node is connected to at least one other node, it will have full connectivity to the entire network because each mesh node forwards packets to other nodes in the network as required. Mesh protocols automatically determine the best route through the network and can dynamically reconfigure the network if a link drops out. The advantages and disadvantages on the use of a wireless mesh network system inside closed aerospace structures are discussed.

Traffic jam driving with NMV avoidance

n recent years, the development of advanced driver assistance systems (ADAS) – mainly based on lidar and cameras – has considerably improved the safety of driving in urban environments. These systems provide warning signals for the driver in the case that any unexpected traffic circumstance is detected. The next step is to develop systems capable not only of warning the driver but also of taking over control of the car to avoid a potential collision. In the present communication, a system capable of autonomously avoiding collisions in traffic jam situations is presented. First, a perception system was developed for urban situations—in which not only vehicles have to be considered, but also pedestrians and other non-motor-vehicles (NMV). It comprises a differential global positioning system (DGPS) and wireless communication for vehicle detection, and an ultrasound sensor for NMV detection. Then, the vehicle's actuators – brake and throttle pedals – were modified to permit autonomous control. Finally, a fuzzy logic controller was implemented capable of analyzing the information provided by the perception system and of sending control commands to the vehicle's actuators so as to avoid accidents. The feasibility of the integrated system was tested by mounting it in a commercial vehicle, with the results being encouraging.

Experimental investigation of radio signal propagation in scientific facilities for telerobotic applications

Understanding the radio signal transmission characteristics in the environment where the telerobotic application is sought is a key part of achieving a reliable wireless communication link between a telerobot and a control station. In this paper, wireless communication requirements and a case study of a typical telerobotic application in an underground facility at CERN are presented. Then, the theoretical and experimental characteristics of radio propagation are investigated with respect to time, distance, location and surrounding objects. Based on analysis of the experimental findings, we show how a commercial wireless system, such as Wi-Fi, can be made suitable for a case study application at CERN.

Herramienta de planificación y dimensionamiento para redes WiMAX

A software tool for planning and dimensioning Wireless Networks based on standard 802.16 is presented in this paper. Due to the deployment of communication systems based on this standard, it is necessary a tool which allows an easy implementation and dimensioning of this type of networks. With this tool the user will be able to evaluate point to point and point to multipoint networks, obtaining results such as losses in the link, power received, signal noise rate, coverage or bit rates the network is able to handle. For that purpose, the tool will employ technical specifications of transmitters and receivers, design parameters of the network and different propagation models.

Energy Management and Optimization for Video Decoders based on Functional-oriented Reconfiguration

In recent years, the increasing sophistication of embedded multimedia systems and wireless communication technologies has promoted a widespread utilization of video streaming applications. It has been reported in 2013 that youngsters, aged between 13 and 24, spend around 16.7 hours a week watching online video through social media, business websites, and video streaming sites. Video applications have already been blended into people daily life. Traditionally, video streaming research has focused on performance improvement, namely throughput increase and response time reduction. However, most mobile devices are battery-powered, a technology that grows at a much slower pace than either multimedia or hardware developments. Since battery developments cannot satisfy expanding power demand of mobile devices, research interests on video applications technology has attracted more attention to achieve energy-efficient designs. How to efficiently use the limited battery energy budget becomes a major research challenge. In addition, next generation video standards impel to diversification and personalization. Therefore, it is desirable to have mechanisms to implement energy optimizations with greater flexibility and scalability. In this context, the main goal of this dissertation is to find an energy management and optimization mechanism to reduce the energy consumption of video decoders based on the idea of functional-oriented reconfiguration. System battery life is prolonged as the result of a trade-off between energy consumption and video quality. Functional-oriented reconfiguration takes advantage of the similarities among standards to build video decoders reconnecting existing functional units. If a feedback channel from the decoder to the encoder is available, the former can signal the latter changes in either the encoding parameters or the encoding algorithms for energy-saving adaption. The proposed energy optimization and management mechanism is carried out at the decoder end. This mechanism consists of an energy-aware manager, implemented as an additional block of the reconfiguration engine, an energy estimator, integrated into the decoder, and, if available, a feedback channel connected to the encoder end. The energy-aware manager checks the battery level, selects the new decoder description and signals to build a new decoder to the reconfiguration engine. It is worth noting that the analysis of the energy consumption is fundamental for the success of the energy management and optimization mechanism. In this thesis, an energy estimation method driven by platform event monitoring is proposed. In addition, an event filter is suggested to automate the selection of the most appropriate events that affect the energy consumption. At last, a detailed study on the influence of the training data on the model accuracy is presented. The modeling methodology of the energy estimator has been evaluated on different underlying platforms, single-core and multi-core, with different characteristics of workload. All the results show a good accuracy and low on-line computation overhead. The required modifications on the reconfiguration engine to implement the energy-aware manager have been assessed under different scenarios. The results indicate a possibility to lengthen the battery lifetime of the system in two different use-cases.

Iterative bit- and power allocation in correlated MIMO systems

In this contribution a novel iterative bit- and power allocation (IBPA) approach has been developed when transmitting a given bit/s/Hz data rate over a correlated frequency non-selective (4× 4) Multiple-Input MultipleOutput (MIMO) channel. The iterative resources allocation algorithm developed in this investigation is aimed at the achievement of the minimum bit-error rate (BER) in a correlated MIMO communication system. In order to achieve this goal, the available bits are iteratively allocated in the MIMO active layers which present the minimum transmit power requirement per time slot.

Modelado de un servicio de M-Salud basado en dinámica de sistemas

En términos generales, m-salud puede definirse como el conjunto de sistemas de información, sensores médicos y tecnologías de comunicaciones móviles para el cuidado de la salud. La creciente disponibilidad, miniaturización, comportamiento, velocidades de transmisión de datos cada vez mayores y la esperada convergencia de tecnologías de red y comunicaciones inalámbricas en torno a los sistemas de salud móviles están acelerando el despliegue de estos sistemas y la provisión de servicios de m-salud, como por ejemplo, la teleasistencia móvil. El concepto emergente de m-salud conlleva retos importantes (estudios técnicos, análisis, modelado de la provisión de servicios, etc.) que hay que afrontar para impulsar la evolución de los sistemas y servicios de e-salud ofrecidos desde tecnologías de telecomunicación que utilizan acceso por cable y redes fijas, hacia configuraciones móviles e inalámbricas de última generación. En este trabajo se analizará primeramente el significado e implicaciones de m-salud y la situación en la que se encuentra; los retos a los que hay que enfrentarse para su implantación y provisión así como su tendencia. De los múltiples y diferentes servicios que se pueden proveer se ha identificado el servicio de Localización de Personas LoPe, lanzado por Cruz Roja en febrero de 2007, para teleasistencia móvil y que permite conocer en todo momento la ubicación de la persona que porta su dispositivo asociado. Orientado a personas con discapacidad, en situación de riesgo o dependencia por deterioro cognitivo, tiene como objetivo ayudarlas a recuperar su autonomía personal. La provisión de este servicio se modelará mediante dinámica de sistemas, ya que esta teoría se considera idónea para modelar sistemas complejos que evolucionan con el tiempo. El resultado final es un modelo que implementado a través de la herramienta Studio 8® de la compañía noruega Powersim Software AS nos ha permitido analizar y evaluar su comportamiento a lo largo del tiempo, además de permitirnos extraer conclusiones sobre el mismo y plantear futuras mejoras sobre el servicio. ABSTRACT. In general terms, m-health can be defined as “mobile computing, medical sensor, and communications technologies for health care.” The increased availability, miniaturization, performance, enhanced data rates, and the expected convergence of future wireless communication and network technologies around mobile health systems are accelerating the deployment of m-health systems and services, for instance, mobile telecare. The emerging concept of m-health involves significant challenges (technical studies, analysis, modeling of service provision, etc.) that must be tackled to drive the development of e-health services and systems offered by telecommunication technologies that use wired and fixed networks towards wireless and mobile new generation networks. Firstly, in this master’s thesis, the meaning and implications of m-health and its current situation are analyzed. This analysis also includes the challenges that must be tackled for the implementation and provision of m-health technologies and services and the m-health trends. Among the many different m-health services already delivered, the Localización de Personas LoPe service has been identified to work with it. This service, launched by Spanish Red Cross in February 2007, enables to locate people who carry the associated device. It’s aimed at people with disabilities, at risk or dependency due to cognitive impairment and helps them to recover their personal autonomy. The provision of this service will be modeled with system dynamics considering that this theory suits very well the modeling of complex systems which evolve over time. The final result is a system dynamics model of the service implemented with Studio 8® tool developed by Powersim Software AS, a Norwegian company. This model has allowed us to analyze and evaluate its behaviour over time, as well as to draw conclusions and to consider some future improvements in the service.

Distribution of microservices for hardware interoperability in the Smart Grid

Due to the significant increase of population and their natural desire of improving their standard of living, usage of energy extracted from world commodities, especially shaped as electricity, has increased in an intense manner during the last decades. This fact brings up a challenge with a complicated solution, which is how to guarantee that there will be enough energy so as to satisfy the energy demand of the world population. Among all the possible solutions that can be adopted to mitigate this problem one of them is almost of mandatory adoption, which consists of rationalizing energy utilization, in a way that its wasteful usage is minimized and it can be leveraged during a longer period of time. One of the ways to achieve it is by means of the improvement of the power distribution grid, so that it will be able to react in a more efficient manner against common issues, such as energy demand peaks or inaccurate electricity consumption forecasts. However, in order to be able to implement this improvement it is necessary to use technologies from the ICT (Information and Communication Technologies) sphere that often present challenges in some key areas: advanced metering infrastructure integration, interoperability and interconnectivity of the devices, interfaces to offer the applications, security measures design, etc. All these challenges may imply slowing down the adoption of the smart grid as a system to prolong the lifespan and utilization of the available energy. A proposal for an intermediation architecture that will make possible solving these challenges is put forward in this Master Thesis. Besides, one implementation and the tests that have been carried out to know the performance of the presented concepts have been included as well, in a way that it can be proved that the challenges set out by the smart grid can be resolved. RESUMEN. Debido al incremento significativo de la población y su deseo natural de mejorar su nivel de vida, la utilización de la energía extraída de las materias primas mundiales, especialmente en forma de electricidad, ha aumentado de manera intensa durante las últimas décadas. Este hecho plantea un reto de solución complicada, el cual es cómo garantizar que se dispondrá de la energía suficiente como para satisfacer la demanda energética de la población mundial. De entre todas las soluciones posibles que se pueden adoptar para mitigar este problema una de ellas es de casi obligatoria adopción, la cual consiste en racionalizar la utilización de la energía, de tal forma que se minimice su malgasto y pueda aprovecharse durante más tiempo. Una de las maneras de conseguirlo es mediante la mejora de la red de distribución de electricidad para que ésta pueda reaccionar de manera más eficaz contra problemas comunes, tales como los picos de demanda de energía o previsiones imprecisas acerca del consumo de electricidad. Sin embargo, para poder implementar esta mejora es necesario utilizar tecnologías del ámbito de las TIC (Tecnologías de la Información y la Comunicación) que a menudo presentan problemas en algunas áreas clave: integración de infraestructura de medición avanzada, interoperabilidad e interconectividad de los dispositivos, interfaces que ofrecer a las aplicaciones, diseño de medidas de seguridad, etc. Todos estos retos pueden implicar una ralentización en la adopción de la red eléctrica inteligente como un sistema para alargar la vida y la utilización de la energía disponible. En este Trabajo Fin de Máster se sugiere una propuesta para una arquitectura de intermediación que posibilite la resolución de estos retos. Además, una implementación y las pruebas que se han llevado a cabo para conocer el rendimiento de los conceptos presentados también han sido incluidas, de tal forma que se demuestre que los retos que plantea la red eléctrica inteligente pueden ser solventados.

Mobile Indoor Augmented Reality. Exploring applications in hospitality environments.

Augmented reality (AR) is been increasingly used in mobile devices. Most of the available applications are set to work outdoors, mainly due to the availability of a reliable positioning system. Nevertheless, indoor (smart) spaces offer a lot of opportunities of creating new service concepts. In particular, in this paper we explore the applicability of mobile AR to hospitality environments (hotels and similar establishments). From the state-of-the-art of technologies and applications, a portfolio of services has been identified and a prototype using off-the-shelf technologies has been designed. Our objective is to identify the next technological challenges to overcome in order to have suitable underlying infrastructures and innovative services which enhance the traveller?s experience.