Ice volume estimates from ground-penetrating radar surveys, western Nordenskiöld Land glaciers, Svalbard

As part of ongoing work within the SvalGlac project aimed to obtain a reliable estimate of the total ice volume of Svalbard glaciers and their potential contribution to sea level rise, in this contribution we present volume calculations, with detailed error estimates, for ten glaciers on western Nordenskiöld Land, central Spitsbergen, Svalbard. The volume estimates are based upon a dense net of GPR-retrieved ice thickness data collected over several field campaigns spanning the period 1999-2012, all of them except one within 2010-2012. The total area and volume of the ensemble are 113.38±0.09 km2 and 10.439±0.185 km3, respectively, while the individual areas, volumes and average ice thickness lie within 2.5-49.1 km2, 0.08-5.48 km3 and 29-108 m, respectively. The maximum recorded ice thickness, 265±15 m, corresponds to Fridtjovbreen, which has also the largest average thickness (108±1m). Available empirical formulae for Svalbard glaciers overestimate the total volume of these glaciers by 24% with respect to our calculation. On the basis of the pattern of scattering in the radargrams, we also analyse the hydrothermal structure of these glaciers. Nine out of ten are polythermal, while only one is entirely cold.

Ice volume estimates from ground-penetrating radar surveys, Wedel Jarlsberg Land glaciers, Svalbard

One of the aims of the SvalGlac project is to obtain an improved estimate, with reliable error estimates, of the volume of Svalbard glaciers and their potential contribution to sea level rise. As part of this work, we present volume calculations, with detailed error estimates, for eight glaciers on Wedel Jarlsberg Land, southern Spitsbergen, Svalbard. The volume estimates are based upon a dense net of GPR-retrieved ice thickness data collected over several field campaigns spanning the period 2004-2011. The total area and volume of the ensemble are 502.9±18.6 km2 and 80.72±2.85 km3, respectively. Excluding Ariebreen (a tiny glacier, menor que 0.4 km2 in area), the individual areas, volumes and average ice thickness lie within 4.7-141.0 km2, 0.30-25.85 km3 and 64-183 m, respectively. The maximum recorded ice thickness, ca. 619±13 m, is found in Austre Torellbreen. To estimate the ice volume of small non-echo-sounded tributary glaciers, we used a function providing the best fit to the ice thickness along the centre line of a collection of such tributaries where echo-soundings were available, and assuming parabolic cross-sections. We did some tests on the effect on the measured ice volumes of the distinct radio-wave velocity (RWV) of firn as compared to ice, and cold versus temperate ice, concluding that the changes in volume implied by such corrections were within the error bounds of our volume estimate using a constant RWV for the entire glacier inferred from common mid-point measurements on the upper ablation area.

Ground-penetrating radar surveys and ice volume estimates of Wedel Jarlsberg Land glaciers, Svalbard

We present volume calculations, with detailed error estimates, for eight glaciers on Wedel Jarlsberg Land, southern Spitsbergen, Svalbard, and compare them to those obtained from area-volume scaling relationships. The volume estimates are based upon a dense net of GPR-retrieved ice thickness data collected over several field campaigns spanning the period 2004-2011.

Effect of LSP treatment on the surface topography, friction and wear of Al2024 alloy

OUTLINE: •Introduction •Experimental Setup • Experimental Procedure • Experimental Results - Surface Roughness - Residual Stresses - Friction - Wear - EDX •Conclusions

Processing of ultra-wideband low-frequency signals, for application in Foliage Penetration (FOPEN) Synthetic Aperture Radar (SAR) systems

Foliage Penetration (FOPEN) radar systems were introduced in 1960, and have been constantly improved by several organizations since that time. The use of Synthetic Aperture Radar (SAR) approaches for this application has important advantages, due to the need for high resolution in two dimensions. The design of this type of systems, however, includes some complications that are not present in standard SAR systems. FOPEN SAR systems need to operate with a low central frequency (VHF or UHF bands) in order to be able to penetrate the foliage. High bandwidth is also required to obtain high resolution. Due to the low central frequency, large integration angles are required during SAR image formation, and therefore the Range Migration Algorithm (RMA) is used. This project thesis identifies the three main complications that arise due to these requirements. First, a high fractional bandwidth makes narrowband propagation models no longer valid. Second, the VHF and UHF bands are used by many communications systems. The transmitted signal spectrum needs to be notched to avoid interfering them. Third, those communications systems cause Radio Frequency Interference (RFI) on the received signal. The thesis carries out a thorough analysis of the three problems, their degrading effects and possible solutions to compensate them. The UWB model is applied to the SAR signal, and the degradation induced by it is derived. The result is tested through simulation of both a single pulse stretch processor and the complete RMA image formation. Both methods show that the degradation is negligible, and therefore the UWB propagation effect does not need compensation. A technique is derived to design a notched transmitted signal. Then, its effect on the SAR image formation is evaluated analytically. It is shown that the stretch processor introduces a processing gain that reduces the degrading effects of the notches. The remaining degrading effect after processing gain is assessed through simulation, and an experimental graph of degradation as a function of percentage of nulled frequencies is obtained. The RFI is characterized and its effect on the SAR processor is derived. Once again, a processing gain is found to be introduced by the receiver. As the RFI power can be much higher than that of the desired signal, an algorithm is proposed to remove the RFI from the received signal before RMA processing. This algorithm is a modification of the Chirp Least Squares Algorithm (CLSA) explained in [4], which adapts it to deramped signals. The algorithm is derived analytically and then its performance is evaluated through simulation, showing that it is effective in removing the RFI and reducing the degradation caused by both RFI and notching. Finally, conclusions are drawn as to the importance of each one of the problems in SAR system design.

Simulación de seguimiento de blancos en sistemas radar. Parte 2

El proyecto consiste en el diseño y estudio de un software cuyas prestaciones estén orientadas a gestionar una simulación de un sistema de radar. El prototipo de este entorno de simulación se ha realizado en el lenguaje Matlab debido a que inicialmente se considera el más adecuado para el tratamiento de las señales que los sistemas de radar manejan para realizar sus cálculos. Se ha escogido como modelo el software desarrollado por la compañía SAP para gestionar los E.R.P.s de grandes empresas. El motivo es que es un software cuyo diseño y funcionalidad es especialmente adecuado para la gestión ordenada de una cantidad grande de datos diversos de forma integrada. Diseñar e implementar el propio entorno es una tarea de enorme complejidad y que requerirá el esfuerzo de una cantidad importante de personas; por lo que este proyecto se ha limitado, a un prototipo básico con una serie de características mínimas; así como a indicar y dejar preparado el camino por el que deberán transcurrir las futuras agregaciones de funcionalidad o mejoras. Funcionalmente, esto es, independientemente de la implementación específica con la que se construya el entorno de simulación, se ha considerado dividir las características y prestaciones ofrecidas por el sistema en bloques. Estos bloques agruparán los componentes relacionados con un aspecto específico de la simulación, por ejemplo, el bloque 1, es el asignado a todo lo relacionado con el blanco a detectar. El usuario del entorno de simulación interactuará con el sistema ejecutando lo que se llaman transacciones, que son agrupaciones lógicas de datos a introducir/consultar en el sistema relacionados y que se pueden ejecutar de forma independiente. Un ejemplo de transacción es la que permite mantener una trayectoria de un blanco junto con sus parámetros, pero también puede ser una transacción la aplicación que permite por ejemplo, gestionar los usuarios con acceso al entorno. Es decir, las transacciones son el componente mínimo a partir del cual el usuario puede interactuar con el sistema. La interfaz gráfica que se le ofrecerá al usuario, está basada en modos, que se pueden considerar “ventanas” independientes entre sí dentro de las cuáles el usuario ejecuta sus transacciones. El usuario podrá trabajar con cuantos modos en paralelo desee y cambiar según desee entre ellos. La programación del software se ha realizado utilizando la metodología de orientación a objetos y se ha intentado maximizar la reutilización del código así como la configurabilidad de su funcionalidad. Una característica importante que se ha incorporado para garantizar la integridad de los datos es un diccionario sintáctico. Para permitir la persistencia de los datos entre sesiones del usuario se ha implementado una base de datos virtual (que se prevé se reemplace por una real), que permite manejar, tablas, campos clave, etc. con el fin de guardar todos los datos del entorno, tanto los de configuración que solo serían responsabilidad de los administradores/desarrolladores como los datos maestros y transaccionales que serían gestionados por los usuarios finales del entorno de simulación. ABSTRACT. This end-of-degree project comprises the design, study and implementation of a software based application able to simulate the various aspects and performance of a radar system. A blueprint for this application has been constructed upon the Matlab programming language. This is due to the fact that initially it was thought to be the one most suitable to the complex signals radar systems usually process; but it has proven to be less than adequate for all the other core processes the simulation environment must provide users with. The software’s design has been based on another existing software which is the one developed by the SAP company for managing enterprises, a software categorized (and considered the paradigm of) as E.R.P. software (E.R.P. stands for Enterprise Resource Planning). This software has been selected as a model because is very well suited (its basic features) for working in an orderly fashion with a pretty good quantity of data of very diverse characteristics, and for doing it in a way which protects the integrity of the data. To design and construct the simulation environment with all its potential features is a pretty hard task and requires a great amount of effort and work to be dedicated to its accomplishment. Due to this, the scope of this end-of-degree project has been focused to design and construct a very basic prototype with minimal features, but which way future developments and upgrades to the systems features should go has also been pointed. In a purely functional approach, i.e. disregarding completely the specific implementation which accomplishes the simulation features, the different parts or aspects of the simulation system have been divided and classified into blocks. The blocks will gather together and comprise the various components related with a specific aspect of the simulation landscape, for example, block number one will be the one dealing with all the features related to the radars system target. The user interaction with the system will be based on the execution of so called transactions, which essentially consist on bunches of information which logically belong together and can thus be managed together. A good example, could be a transaction which permits to maintain a series of specifications for target’s paths; but it could also be something completely unrelated with the radar system itself as for example, the management of the users who can access the system. Transactions will be thus the minimum unit of interaction of users with the system. The graphic interface provided to the user will be mode based, which can be considered something akin to a set of independent windows which are able on their own to sustain the execution of an independent transaction. The user ideally should be able to work with as many modes simultaneously as he wants to, switching his focus between them at will. The approach to the software construction has been based on the object based paradigm. An effort has been made to maximize the code’s reutilization and also in maximizing its customizing, i.e., same sets of code able to perform different tasks based on configuration data. An important feature incorporated to the software has been a data dictionary (a syntactic one) which helps guarantee data integrity. Another important feature that allow to maintain data persistency between user sessions, is a virtual relational data base (which should in future times become a real data base) which allows to store data in tables. The data store in this tables comprises both the system’s configuration data (which administrators and developers will maintain) and also master and transactional data whose maintenance will be the end users task.

Diseño de algoritmos de guerra electrónica y radar para su implementación en sistemas de tiempo real

Esta tesis se centra en el estudio y desarrollo de algoritmos de guerra electrónica {electronic warfare, EW) y radar para su implementación en sistemas de tiempo real. La llegada de los sistemas de radio, radar y navegación al terreno militar llevó al desarrollo de tecnologías para combatirlos. Así, el objetivo de los sistemas de guerra electrónica es el control del espectro electomagnético. Una de la funciones de la guerra electrónica es la inteligencia de señales {signals intelligence, SIGINT), cuya labor es detectar, almacenar, analizar, clasificar y localizar la procedencia de todo tipo de señales presentes en el espectro. El subsistema de inteligencia de señales dedicado a las señales radar es la inteligencia electrónica {electronic intelligence, ELINT). Un sistema de tiempo real es aquel cuyo factor de mérito depende tanto del resultado proporcionado como del tiempo en que se da dicho resultado. Los sistemas radar y de guerra electrónica tienen que proporcionar información lo más rápido posible y de forma continua, por lo que pueden encuadrarse dentro de los sistemas de tiempo real. La introducción de restricciones de tiempo real implica un proceso de realimentación entre el diseño del algoritmo y su implementación en plataformas “hardware”. Las restricciones de tiempo real son dos: latencia y área de la implementación. En esta tesis, todos los algoritmos presentados se han implementado en plataformas del tipo field programmable gate array (FPGA), ya que presentan un buen compromiso entre velocidad, coste total, consumo y reconfigurabilidad. La primera parte de la tesis está centrada en el estudio de diferentes subsistemas de un equipo ELINT: detección de señales mediante un detector canalizado, extracción de los parámetros de pulsos radar, clasificación de modulaciones y localization pasiva. La transformada discreta de Fourier {discrete Fourier transform, DFT) es un detector y estimador de frecuencia quasi-óptimo para señales de banda estrecha en presencia de ruido blanco. El desarrollo de algoritmos eficientes para el cálculo de la DFT, conocidos como fast Fourier transform (FFT), han situado a la FFT como el algoritmo más utilizado para la detección de señales de banda estrecha con requisitos de tiempo real. Así, se ha diseñado e implementado un algoritmo de detección y análisis espectral para su implementación en tiempo real. Los parámetros más característicos de un pulso radar son su tiempo de llegada y anchura de pulso. Se ha diseñado e implementado un algoritmo capaz de extraer dichos parámetros. Este algoritmo se puede utilizar con varios propósitos: realizar un reconocimiento genérico del radar que transmite dicha señal, localizar la posición de dicho radar o bien puede utilizarse como la parte de preprocesado de un clasificador automático de modulaciones. La clasificación automática de modulaciones es extremadamente complicada en entornos no cooperativos. Un clasificador automático de modulaciones se divide en dos partes: preprocesado y el algoritmo de clasificación. Los algoritmos de clasificación basados en parámetros representativos calculan diferentes estadísticos de la señal de entrada y la clasifican procesando dichos estadísticos. Los algoritmos de localization pueden dividirse en dos tipos: triangulación y sistemas cuadráticos. En los algoritmos basados en triangulación, la posición se estima mediante la intersección de las rectas proporcionadas por la dirección de llegada de la señal. En cambio, en los sistemas cuadráticos, la posición se estima mediante la intersección de superficies con igual diferencia en el tiempo de llegada (time difference of arrival, TDOA) o diferencia en la frecuencia de llegada (frequency difference of arrival, FDOA). Aunque sólo se ha implementado la estimación del TDOA y FDOA mediante la diferencia de tiempos de llegada y diferencia de frecuencias, se presentan estudios exhaustivos sobre los diferentes algoritmos para la estimación del TDOA, FDOA y localización pasiva mediante TDOA-FDOA. La segunda parte de la tesis está dedicada al diseño e implementación filtros discretos de respuesta finita (finite impulse response, FIR) para dos aplicaciones radar: phased array de banda ancha mediante filtros retardadores (true-time delay, TTD) y la mejora del alcance de un radar sin modificar el “hardware” existente para que la solución sea de bajo coste. La operación de un phased array de banda ancha mediante desfasadores no es factible ya que el retardo temporal no puede aproximarse mediante un desfase. La solución adoptada e implementada consiste en sustituir los desfasadores por filtros digitales con retardo programable. El máximo alcance de un radar depende de la relación señal a ruido promedio en el receptor. La relación señal a ruido depende a su vez de la energía de señal transmitida, potencia multiplicado por la anchura de pulso. Cualquier cambio hardware que se realice conlleva un alto coste. La solución que se propone es utilizar una técnica de compresión de pulsos, consistente en introducir una modulación interna a la señal, desacoplando alcance y resolución. ABSTRACT This thesis is focused on the study and development of electronic warfare (EW) and radar algorithms for real-time implementation. The arrival of radar, radio and navigation systems to the military sphere led to the development of technologies to fight them. Therefore, the objective of EW systems is the control of the electromagnetic spectrum. Signals Intelligence (SIGINT) is one of the EW functions, whose mission is to detect, collect, analyze, classify and locate all kind of electromagnetic emissions. Electronic intelligence (ELINT) is the SIGINT subsystem that is devoted to radar signals. A real-time system is the one whose correctness depends not only on the provided result but also on the time in which this result is obtained. Radar and EW systems must provide information as fast as possible on a continuous basis and they can be defined as real-time systems. The introduction of real-time constraints implies a feedback process between the design of the algorithms and their hardware implementation. Moreover, a real-time constraint consists of two parameters: Latency and area of the implementation. All the algorithms in this thesis have been implemented on field programmable gate array (FPGAs) platforms, presenting a trade-off among performance, cost, power consumption and reconfigurability. The first part of the thesis is related to the study of different key subsystems of an ELINT equipment: Signal detection with channelized receivers, pulse parameter extraction, modulation classification for radar signals and passive location algorithms. The discrete Fourier transform (DFT) is a nearly optimal detector and frequency estimator for narrow-band signals buried in white noise. The introduction of fast algorithms to calculate the DFT, known as FFT, reduces the complexity and the processing time of the DFT computation. These properties have placed the FFT as one the most conventional methods for narrow-band signal detection for real-time applications. An algorithm for real-time spectral analysis for user-defined bandwidth, instantaneous dynamic range and resolution is presented. The most characteristic parameters of a pulsed signal are its time of arrival (TOA) and the pulse width (PW). The estimation of these basic parameters is a fundamental task in an ELINT equipment. A basic pulse parameter extractor (PPE) that is able to estimate all these parameters is designed and implemented. The PPE may be useful to perform a generic radar recognition process, perform an emitter location technique and can be used as the preprocessing part of an automatic modulation classifier (AMC). Modulation classification is a difficult task in a non-cooperative environment. An AMC consists of two parts: Signal preprocessing and the classification algorithm itself. Featurebased algorithms obtain different characteristics or features of the input signals. Once these features are extracted, the classification is carried out by processing these features. A feature based-AMC for pulsed radar signals with real-time requirements is studied, designed and implemented. Emitter passive location techniques can be divided into two classes: Triangulation systems, in which the emitter location is estimated with the intersection of the different lines of bearing created from the estimated directions of arrival, and quadratic position-fixing systems, in which the position is estimated through the intersection of iso-time difference of arrival (TDOA) or iso-frequency difference of arrival (FDOA) quadratic surfaces. Although TDOA and FDOA are only implemented with time of arrival and frequency differences, different algorithms for TDOA, FDOA and position estimation are studied and analyzed. The second part is dedicated to FIR filter design and implementation for two different radar applications: Wideband phased arrays with true-time delay (TTD) filters and the range improvement of an operative radar with no hardware changes to minimize costs. Wideband operation of phased arrays is unfeasible because time delays cannot be approximated by phase shifts. The presented solution is based on the substitution of the phase shifters by FIR discrete delay filters. The maximum range of a radar depends on the averaged signal to noise ratio (SNR) at the receiver. Among other factors, the SNR depends on the transmitted signal energy that is power times pulse width. Any possible hardware change implies high costs. The proposed solution lies in the use of a signal processing technique known as pulse compression, which consists of introducing an internal modulation within the pulse width, decoupling range and resolution.

Estimación de biomasa forestal mediante el uso de imágenes radar.

La importancia de la Biomasa a nivel mundial, ha llevado a que más de 130 países celebren el protocolo de Kioto sobre el cambio climático dictaminando como objetivo la reducción de las emisiones de seis gases de efecto invernadero y tres gases industriales fluorados, así como la incorporación de la fijación del CO2 como un objetivo dentro de los criterios de gestión de bosques. Entre las metodologías no destructivas para estimación de biomasa, aquí desarrolladas se describen tres técnicas que varios autores han propuesto para calcular los valores de biomasa y carbono, tal como el uso de ecuaciones alométricas por medio de la medición de variables dasométricas como el DAP, la aplicación de la teoría de huecos (v.g. DHP, TRAC), y la obtención de biomasa mediante información radar. Las imágenes radar proporcionan una clara ventaja al poder ser adquiridas en cualquier momento del día e independientemente de las condiciones climatológicas. Se han adquirido dos imágenes de sensores diferentes, tal como ALOSPALSAR que trabaja en la banda L y RADARSAT-2 que trabaja en la banda C, se aplica la metodología descrita por Saatchi et al. (2007), desarrollando los algoritmos semiempíricos propuestos para la estimación de biomasa del fuste (Ws) y biomasa de la copa (Wc), obteniendo los coeficientes a partir de información adquirida en campo. ABSTRACT The importance of biomass worldwide has led to more than 130 countries to celebrate the Kyoto Protocol, aimed at reducing emissions of six greenhouse gases and three fluorinated industrial gases, and the incorporation of the fixation of CO2 as an objective within forest management criteria. Among the non-destructive methods for estimating biomass, three techniques were developed. These have been described by some authors, as the use of allometric equations by measuring forest variables such as the DAP, the application of the Gap Theory (e.g. DHP, TRAC), as well as deriving biomass by radar information. The radar images provide a clear advantage since they can be gathered at any time of the day regardless of the weather conditions. For this purpose, two radar products have acquired from different sensors, such as ALOSPALSAR operating on L frequency band and RADARSAT-2 operating on C frequency band. The methodology applied in this work is described in Saatchi et al. (2007), that develop semiempirical algorithms for estimating stem biomass (Ws) and crown biomass (Wc). The corresponding coefficients are determined by means of regression procedures using field information derived from allometric and radiation measurements.

Radar track segmentation with cubic splines for collision risk models in high density terminal areas

This paper presents a method to segment airplane radar tracks in high density terminal areas where the air traffic follows trajectories with several changes in heading, speed and altitude. The radar tracks are modelled with different types of segments, straight lines, cubic spline function and shape preserving cubic function. The longitudinal, lateral and vertical deviations are calculated for terminal manoeuvring area scenarios. The most promising model of the radar tracks resulted from a mixed interpolation using straight lines for linear segments and spline cubic functions for curved segments. A sensitivity analysis is used to optimise the size of the window for the segmentation process.

Compact duplexing for a 680-GHz radar using a waveguide orthomode transducer

A compact 680-GHz waveguide orthomode transducer (OMT) and circular horn combination has been designed, tested, and characterized in a radar transceiver's duplexer. The duplexing capability is implemented by a hybrid waveguide quasi optical solution, combining a linear polarization OMT and an external grating polarizer. Isolation between the OMT's orthogonal ports' flanges was measured with a vector network analyzer to exceed 33 dB over a >10% bandwidth between 630 and 710 GHz. Calibrated Y-factor measurements using a mixer attached to the OMT ports reveal losses through the transmit and receive paths that sum to an average of 4.7 dB of two-way loss over 660-690 GHz. This is consistent with radar sensitivity measurements comparing the new OMT/horn with a quasi-optical wire grid beam splitter. Moreover, the radar performance assessment validates the OMT as a suitable compact substitute of the wire grid for the JPL's short-range 680-GHz imaging radar.

Low-Cost Radar-Based Target Identification Prototype using an Expert System

Smart and green cities are hot topics in current research because people are becoming more conscious about their impact on the environment and the sustainability of their cities as the population increases. Many researchers are searching for mechanisms that can reduce power consumption and pollution in the city environment. This paper addresses the issue of public lighting and how it can be improved in order to achieve a more energy efficient city. This work is focused on making the process of turning the streetlights on and off more intelligent so that they consume less power and cause less light pollution. The proposed solution is comprised of a radar device and an expert system implemented on a low-cost platform based on a DSP. By analyzing the radar echo in both the frequency and time domains, the system is able to detect and identify objects moving in front of it. This information is used to decide whether or not the streetlight should be turned on. Experimental results show that the proposed system can provide hit rates over 80%, promising a good performance. In addition, the proposed solution could be useful in kind of other applications such as intelligent security and surveillance systems and home automation.

Diseño y simulación de detectores de señales radar utilizando técnicas tiempo-frecuencia

El objetivo de este trabajo fin de grado (TFG) consiste en estudiar algunas técnicas de análisis tiempo-frecuencia y aplicarlas a la detección de señales radar. Estas técnicas se incorporan en los actuales equipos de guerra electrónica radar, tales como los interceptadores digitales. La principal motivación de estos equipos consiste en detectar y localizar las fuentes radiantes enemigas e intentar obtener cierta información de las señales interceptadas, tal como, la dirección de llegada (DOA, Direction Of Arrival), el tiempo de llegada (TOA, Time Of Arrival), amplitud de pulso (PA, Pulse Amplitude), anchura de pulso (PW, Pulse Width), frecuencia instantánea (IF, Instantaneous Frequency) o modulación intrapulso. Se comenzará con un estudio detallado de la Short-Time Fourier Transform (STFT),dado su carácter lineal es la técnica más explotada actualmente. Este algoritmo presenta una mala resolución conjunta tiempo-frecuencia. Este hecho provoca el estudio complementario de una segunda técnica de análisis basada en la distribución de Wigner-Ville (WVD). Mediante este método se logra una resolución optima tiempo-frecuencia. A cambio, se obtienen términos cruzados indeseados debido a su carácter cuadrático. Uno de los objetivos de este TFG reside en calcular la sensibilidad de los sistemas de detección analizados a partir de las técnicas tiempo-frecuencia. Se hará uso del método de Monte Carlo para estimar ciertos parámetros estadísticos del sistema tales como la probabilidad de falsa alarma y de detección. Así mismo, se llevará a cabo el estudio completo de un receptor digital de guerra electrónica a fin de comprender el funcionamiento de todos los subsistemas que componen el conjunto (STFT/WVD, medidor instantáneo de frecuencias, procesamiento no coherente y generación de descriptores de pulso). Por último, se analizará su comportamiento frente a diferentes señales Radar (FM-lineal, BPSK, chirp o Barker). Se utilizará para ello la herramienta Matlab.

Diseño de una antena de ranura para un radar de basura espacial

Este trabajo realiza un estudio de estructuras radiantes basadas en ranuras sobre guía radial de un haz monopulso (suma y diferencia). Las características de estas estructuras de antena son su facilidad de construcción, polarización circular, bajas pérdidas y ancho de banda inversamente proporcional a su ganancia (debido a la excitación serie). El trabajo comienza con un estudio bibliográfico de antenas existentes, continúa con la aplicación objetivo y realiza un diseño. El objetivo del trabajo es el estudio de viabilidad de una antena de ranuras con una disposición de anillos concéntricos en la banda W con polarización circular. El diseño propuesto trabaja a una frecuencia de 94 GHz. Para ello, se aplicaría un procedimiento de síntesis basado en métodos de optimización con el fin de determinar la longitud y la posición de cada una de las ranuras. En la etapa de diseño de la antena se estudiará cuál es la mejor opción para el diseño de nuestra antena, cuáles son las longitudes de la ranuras, cuál es la distancia de cada anillo, con que separación. Con ello perseguimos, que nuestro array tenga la mayor ganancia posible, respetando que sea una de dimensiones reales. Para escoger correctamente los parámetros mencionados anteriormente se ha diseñado una herramienta de optimización utilizando el software comercial Matlab. Esta herramienta utiliza diversos algoritmos para poder optimizar correctamente nuestro elemento radiante: fmincon, herramienta de búsqueda local con restricciones para funciones multivariable no lineales y “simulannealbnd”, herramienta de búsqueda global con restricciones. Se utilizará una combinación de ambas herramientas con el objetivo de mejorar los resultados del primero y aumentando la velocidad de convergencia del segundo.

Ice volume estimates from ground-penetrating radar surveys, Wedel Jarlsberg Land glaciers, Svalbard

We present ground-penetrating radar (GPR)—based volume calculations, with associated error estimates, for eight glaciers on Wedel Jarlsberg Land, southwestern Spitsbergen, Svalbard, and compare them with those obtained from volume-area scaling relationships. The volume estimates are based upon GPR ice-thickness data collected during the period 2004–2013. The total area and volume of the ensemble are 502.91 ± 18.60 km2 and 91.91 ± 3.12 km3, respectively. The individual areas, volumes, and average ice thickness lie within 0.37–140.99 km2, 0.01–31.98 km3, and 28–227 m, respectively, with a maximum recorded ice thickness of 619 ± 13 m on Austre Torellbreen. To estimate the ice volume of unsurveyed tributary glaciers, we combine polynomial cross-sections with a function providing the best fit to the measured ice thickness along the center line of a collection of 22 surveyed tributaries. For the time-to-depth conversion of GPR data, we test the use of a glacierwide constant radio-wave velocity chosen on the basis of local or regional common midpoint measurements, versus the use of distinct velocities for the firn, cold ice, and temperate ice layers, concluding that the corresponding volume calculations agree with each other within their error bounds.

Aplicación práctica transceptor BGT24MTR11 : radar Doppler

En los últimos tiempos, los radares han dejado de ser instrumentos utilizados únicamente en aviación, defensa y detección de velocidad. El avance de la tecnología de radiofrecuencia ha permitido la reducción de coste, tamaño y consumo de los componentes radar. Esto ha permitido que cada sea más frecuente el uso del radar en elementos de nuestra vida cotidiana tales como la automoción, la seguridad, la medida de líquidos… Este proyecto se basa en uno de estos nuevos componentes de bajo coste y pequeño tamaño, el transceptor BGT24MTR11. El BGTR24MTR11 integra transmisor, VCO y receptor, los elementos principales para la creación de un radar Doppler en la banda de frecuencia ISM 24-24,25 GHz. A partir de la placa de evaluación de ese transceptor, se aborda el diseño de un prototipo/demostrador de radar Doppler CW en la banda de 24 GHz. Para la generación de frecuencia se utiliza la placa de evaluación del PLL HMC702 y se ha diseñado un PCB a medida cuyas funciones son las de alimentación, programación y amplificación de las señales recibidas por el prototipo. Por último, se comprueba el correcto funcionamiento del prototipo y se verifica su funcionamiento mediante la simulación de dos escenarios de prueba. ABSTRACT. In the recent times, radar systems have changed of being tools used only in aviation, defence and speed detection. Radiofrequency technology improvements have allowed a cost, size and power consumption of the radar components. This is the reason because each time is more frequent the use of radar in elements of our daily life such as automotive, security, liquid measurements… This Project is base don one of this low power and size components, the MMIC transceptor BGT24MTR11. This transceptor integrates the main components needed to make a Doppler radar in the ISM Band (24-24 GHz), the transmitter, the receiver with the low noise amplifier and the VCO. Using the evaluation board of this transceptor, this Project approach the design of a CW Doppler radar prototype/demonstrator in the frequency band of 24 GHz. The frequency generation is based on the use of the HMC702 PLL evaluation board. Moreover, it has been designed a custom PCB whose funcionts are the power supply, programation and amplification of the signals received by the prototype. At the end, the correct operation of the prototype is verified and it is tested simulating two different test scenarios.