A 2D computational parametric analysis of the sheltering effect of fences on a railway vehicle standing on a bridge and experiencing crosswinds

In a crosswind scenario, the risk of high-speed trains overturning increases when they run on viaducts since the aerodynamic loads are higher than on the ground. In order to increase safety, vehicles are sheltered by fences that are installed on the viaduct to reduce the loads experienced by the train. Windbreaks can be designed to have different heights, and with or without eaves on the top. In this paper, a parametric study with a total of 12 fence designs was carried out using a two-dimensional model of a train standing on a viaduct. To asses the relative effectiveness of sheltering devices, tests were done in a wind tunnel with a scaled model at a Reynolds number of 1 × 105, and the train’s aerodynamic coefficients were measured. Experimental results were compared with those predicted by Unsteady Reynolds-averaged Navier-Stokes (URANS) simulations of flow, showing that a computational model is able to satisfactorily predict the trend of the aerodynamic coefficients. In a second set of tests, the Reynolds number was increased to 12 × 106 (at a free flow air velocity of 30 m/s) in order to simulate strong wind conditions. The aerodynamic coefficients showed a similar trend for both Reynolds numbers; however, their numerical value changed enough to indicate that simulations at the lower Reynolds number do not provide all required information. Furthermore, the variation of coefficients in the simulations allowed an explanation of how fences modified the flow around the vehicle to be proposed. This made it clear why increasing fence height reduced all the coefficients but adding an eave had an effect mainly on the lift force coefficient. Finally, by analysing the time signals it was possible to clarify the influence of the Reynolds number on the peak-to-peak amplitude, the time period and the Strouhal number.

A first approach to the optimization of Bogotá's TransMilenio BRT system

Bus rapid transit (BRT) systems are massive transport systems with medium/high capacity, high quality service and low infrastructure and operating costs. TransMilenio is Bogotá's most important mass transportation system and one of the biggest BRT systems in the world, although it only has completed its third construction phase out of a total of eight. In this paper we review the proposals in the literature to optimize BRT system operation, with a special emphasis on TransMilenio, and propose a mathematical model that adapts elements of the above proposals and incorporates novel elements accounting for the features of TransMilenio system.

BHLS, Bus, tram: tesi, antitesi, sintesi.

Il sistema di trasporto detto Bus Rapid Transit (BRT) è stato lanciato a Curitiba, in Brasile, nel 1974 per offrire un trasporto in bus efficiente ed efficace nella città in rapida espansione. Questa sperienza, insieme a quella di Ottawa (1983) e Quito (1994) ha dimostrato di essere una soluzione molto efficiente per il trasporto di massa. Per tutta l’Europa si sono iniziate a sviluppare esperienze simili, introducendo però un concetto diverso per quanto riguarda la qualità di servizio. Infatti sistemi come il “trunk network” nella Svezia, il Metrobus nella Germania oppure il BHNS (Bus à Aut. Niveau de Service) nella Francia trattano la qualità di servizio da una prospettiva più ampia che il BRT, dato che considerano aspetti come l’immagine ed il comfort oltre che velocità, frequenza e affidabilità. Questi nuovi sistemi BHLS (Buses with a High Quality of Service) consentono di combinare la qualità di servizio del tram con il costo basso e l’altà flessibilità dei sistema bus, fornendo soluzioni molto interessanti in termini di accessibilità e livelli di servizio, che permettono l’adattamento ai differenti contesti urbani (dimensione, popolazione, densità, ecc.). This article compares different European experiences with tramways and BHLS, especially from the economic point of view, considering their respective costs, benefits and advantages altogether.

A model for setting services on auxiliary bus lines under congestion

In this paper, a mathematical programming model and a heuristically derived solution is described to assist with the efficient planning of services for a set of auxiliary bus lines (a bus-bridging system) during disruptions of metro and rapid transit lines. The model can be considered static and takes into account the average flows of passengers over a given period of time (i.e., the peak morning traffic hour) Auxiliary bus services must accommodate very high demand levels, and the model presented is able to take into account the operation of a bus-bridging system under congested conditions. A general analysis of the congestion in public transportation lines is presented, and the results are applied to the design of a bus-bridging system. A nonlinear integer mathematical programming model and a suitable approximation of this model are then formulated. This approximated model can be solved by a heuristic procedure that has been shown to be computationally viable. The output of the model is as follows: (a) the number of bus units to assign to each of the candidate lines of the bus-bridging system; (b) the routes to be followed by users passengers of each of the origin–destination pairs; (c) the operational conditions of the components of the bus-bridging system, including the passenger load of each of the line segments, the degree of saturation of the bus stops relative to their bus input flows, the bus service times at bus stops and the passenger waiting times at bus stops. The model is able to take into account bounds with regard to the maximum number of passengers waiting at bus stops and the space available at bus stops for the queueing of bus units. This paper demonstrates the applicability of the model with two realistic test cases: a railway corridor in Madrid and a metro line in Barcelona Planificación de los servicios de lineas auxiliares de autobuses durante las incidencias de las redes de metro y cercanías. El modelo estudia el problema bajo condiciones de alta demanda y condiciones de congestión. El modelo no lineal resultante es resuelto mediante heurísticas que demuestran su utilidad. Se demuestran los resultados en dos corredores de las ciudades de Barcelona y Madrid.

Analysis of the railway track as a spatially periodic structure

This article presents a new and computationally efficient method of analysis of a railway track modelled as a continuous beam of 2N spans supported by elastic vertical springs. The main feature of this method is its important reduction in computational effort with respect to standard matrix methods of structural analysis. In this article, the whole structure is considered to be a repetition of a single one. The analysis presented is applied to a simple railway track model, i.e. to a repetitive beam supported on vertical springs (sleepers). The proposed method of analysis is based on the general theory of spatially periodic structures. The main feature of this theory is the possibility to apply Discrete Fourier Transform (DFT) in order to reduce a large system of q(2N + 1) linear stiffness equilibrium equations to a set of 2N + 1 uncoupled systems of q equations each. In this way, a dramatic reduction of the computational effort of solving the large system of equations is achieved. This fact is particularly important in the analysis of railway track structures, in which N is a very large number (around several thousands), and q = 2, the vertical displacement and rotation, is very small. The proposed method allows us to easily obtain the exact solution given by Samartín [1], i.e. the continuous beam railway track response. The comparison between the proposed method and other methods of analysis of railway tracks, such as Lorente de Nó and Zimmermann-Timoshenko, clearly shows the accuracy of the obtained results for the proposed method, even for low values of N. In addition, identical results between the proposed and the Lorente methods have been found, although the proposed method seems to be of simpler application and computationally more efficient than the Lorente one. Small but significative differences occur between these two methods and the one developed by Zimmermann-Timoshenko. This article also presents a detailed sensitivity analysis of the vertical displacement of the sleepers. Although standard matrix methods of structural analysis can handle this railway model, one of the objectives of this article is to show the efficiency of DFT method with respect to standard matrix structural analysis. A comparative analysis between standard matrix structural analysis and the proposed method (DFT), in terms of computational time, input, output and also software programming, will be carried out. Finally, a URL link to a MatLab computer program list, based on the proposed method, is given

Comparative study of the effect of several trains on the ballast rotation

The ballast pick-up (or ballast train-induced-wind erosion (BTE)) phenomenon is a limiting factor for the maximum allowed operational train speed. The determination of the conditions for the initiation of the motion of the ballast stones due to the wind gust created by high-speed trains is critical to predict the start of ballast pick-up because, once the motion is initiated, a saltation-like chain reaction can take place. The aim of this paper is to present a model to evaluate the effect of a random aerodynamic impulse on stone motion initiation, and an experimental study performed to check the capability of the proposed model to classify trains by their effect on the ballast due to the flow generated by the trains. A measurement study has been performed at kp 69 + 500 on the Madrid – Barcelona High Speed Line. The obtained results show the feasibility of the proposed method, and contribute to a technique for BTE characterization, which can be relevant for the development of train interoperability standards