Particle filtering for indoor RFID tag tracking

In this paper, we propose a particle filtering (PF) method for indoor tracking using radio frequency identification (RFID) based on aggregated binary measurements. We use an Ultra High Frequency (UHF) RFID system that is composed of a standard RFID reader, a large set of standard passive tags whose locations are known, and a newly designed, special semi-passive tag attached to an object that is tracked. This semi-passive tag has the dual ability to sense the backscatter communication between the reader and other passive tags which are in its proximity and to communicate this sensed information to the reader using backscatter modulation. We refer to this tag as a sense-a-tag (ST). Thus, the ST can provide the reader with information that can be used to determine the kinematic parameters of the object on which the ST is attached. We demonstrate the performance of the method with data obtained in a laboratory environment.

Fabrication process of Mo/Au TES at RT

We report on the fabrication details of TES based on Mo/Au bilayers. The Mo layer is deposited by radio frequency (RF) sputtering and capped with a sputter deposited thin Au protection layer. Afterwards, a second Au layer of suitable (lower) resistivity is deposited ex‐situ by e‐beam evaporation, until completion of the total desired Au thickness. The deposition was performed at room temperature (RT) on LPCVD Si3 N4 membranes. Such a deposition procedure is very reproducible and allow controlling the critical temperature (Tc) and normal electrical resistance (RN ) of the Mo/Au bilayer. The process is optimized to achieve low stress bilayers, thus avoiding the undesirable curvature of the membranes. Bilayers are patterned using photolithographic techniques and wet etching procedures. Mo superconducting paths are used to contact the Mo/Au bilayers, thus ensuring good electrical conductivity and thermal isolation. The entire fabrication process let to stable and reproducible sensors with required and tunable functional properties

Single-Stage Grid-Connected Forward Microinverter with Boundary Mode Control

This paper presents a microinverter to be integrated into a solar module. The proposed solution combines a forward converter and a constant off-time boundary mode control, providing MPPT capability and unity power factor in a single-stage converter. The transformer structure of the power stage remains as in the classical DC-DC forward converter. Transformer primary windings are utilized for power transfer or demagnetization depending on the grid semi-cycle. Furthermore, bidirectional switches are used on the secondary side allowing direct connection of the inverter to the grid. Design considerations for the proposed solution are provided, regarding the inductance value, transformer turns ratio and frequency variation during a line semi-cycle. The decoupling of the twice the line frequency power pulsation is also discussed, as well as the maximum power point tracking (MPPT) capability. Simulation and experimental results for a 100W prototype are enclosed

Estudio de la precisión de los modelos de transistores de radiofrecuencia y su efecto en un circuito real

Este Proyecto Fin de Carrera trata sobre el estudio de la precisión de los modelos de transistores de radiofrecuencia y el efecto que la misma produce en un circuito real, como es la variabilidad de diversas magnitudes tales como la ganancia y el punto de compresión a 1 decibelio. Para ello se ha construido un circuito de pruebas que ha sido sometido a diversas simulaciones y sobre el que se han realizado numerosas medidas que han sido analizadas mediante software de análisis estadístico. This Final Year Project is about the study of the precision of models of radio frequency transistors and the effect it produces in a real circuit, as is the variability of various magnitudes such as gain and one‐decibel compression point. For this we have built a test circuit that has been subjected to various simulations and on which there have been numerous measures that have been analyzed by statistical analysis software.

Wireless Optical Communications for Intra-Spacecraft Networks Based on OCDMA with Random Optical Codes

In recent years, spacial agencies have shown a growing interest in optical wireless as an alternative to wired and radio-frequency communications. The use of these techniques for intra-spacecraft communications reduces the effect of take-off acceleration and vibrations on the systems by avoiding the need for rugged connectors and provides a significant mass reduction. Diffuse transmission also eases the design process as terminals can be placed almost anywhere without a tight planification to ensure the proper system behaviour. Previous studies have compared the performance of radio-frequency and infrared optical communications. In an intra-satellite environment optical techniques help reduce EMI related problems, and their main disadvantages - multipath dispersion and the need for line-of-sight - can be neglected due to the reduced cavity size. Channel studies demonstrate that the effect of the channel can be neglected in small environments if data bandwidth is lower than some hundreds of MHz.

Novel system for bite-force sensing and monitoring based on magnetic eear field communication

Intraoral devices for bite-force sensing have several applications in odontology and maxillofacial surgery, as bite-force measurements provide additional information to help understand the characteristics of bruxism disorders and can also be of help for the evaluation of post-surgical evolution and for comparison of alternative treatments. A new system for measuring human bite forces is proposed in this work. This system has future applications for the monitoring of bruxism events and as a complement for its conventional diagnosis. Bruxism is a pathology consisting of grinding or tight clenching of the upper and lower teeth, which leads to several problems such as lesions to the teeth, headaches, orofacial pain and important disorders of the temporomandibular joint. The prototype uses a magnetic field communication scheme similar to low-frequency radio frequency identification (RFID) technology (NFC). The reader generates a low-frequency magnetic field that is used as the information carrier and powers the sensor. The system is notable because it uses an intra-mouth passive sensor and an external interrogator, which remotely records and processes information regarding a patient?s dental activity. This permits a quantitative assessment of bite-force, without requiring intra-mouth batteries, and can provide supplementary information to polysomnographic recordings, current most adequate early diagnostic method, so as to initiate corrective actions before irreversible dental wear appears. In addition to describing the system?s operational principles and the manufacture of personalized prototypes, this report will also demonstrate the feasibility of the system and results from the first in vitro and in vivo trials.

Synchronous Buck converter with Output Impedance Correction Circuit

This work is related to the improvement of the output impedance of the Buck converter by means of introducing an additional power path that virtually increases the output capacitance during transients. It is well known that in VRM applications, with wide load steps, voltage overshoots and undershoots may lead to undesired performance of the load. To solve this problem, high-bandwidth high-switching frequency power converters can be applied to reduce the transient time or a big output capacitor can be applied to reduce the output impedance. The first solution can degrade the efficiency by increasing switching losses of the MOSFETS, and the second solution is penalizing the cost and size of the output filter. The Output Impedance Correction Circuit (OICC), as presented here, is used to inject or extract a current n-1 times larger than the output capacitor current, thus virtually increasing n times the value of the output capacitance during the transients. This feature allows the usage of a low frequency Buck converter with smaller capacitor but satisfying the dynamic requirements.

Improvement of the Dynamic Performance of a Buck Converter using Controlled Current Source as an Additional Energy Path

This work is related to the improvement of the dynamic performance of the Buck converter by means of introducing an additional power path that virtually increase s the output capacitance during transients, thus improving the output impedance of the converter. It is well known that in VRM applications, with wide load steps, voltage overshoots and undershoots ma y lead to undesired performance of the load. To solve this problem, high-bandwidth high-switching frequency power converter s can be applied to reduce the transient time or a big output capacitor can be applied to reduce the output impedance. The first solution can degrade the efficiency by increasing switching losses of the MOSFETS, and the second solution is penalizing the cost and size of the output filter. The additional energy path, as presented here, is introduced with the Output Impedance Correction Circuit (OICC) based on the Controlled Current Source (CCS). The OICC is using CCS to inject or extract a current n - 1 times larger than the output capacitor current, thus virtually increasing n times the value of the output capacitance during the transients. This feature allows the usage of a low frequency Buck converter with smaller capacitor but satisfying the dynamic requirements.

Estudio y desarrollo sobre sistemas de simulación para comunicaciones móviles, LTE

Este proyecto, recoge el estudio de diferentes simuladores sobre comunicaciones móviles, que se encargan de analizar el comportamiento de las tecnologías UMTS (Universal Mobile Telecommunications System), 3G y LTE (Long Term Evolution),3.9G, centrándose principalmente en el caso de los simuladores LTE, ya que es la tecnología que se está implantando en la actualidad. Por ello, antes de analizar las características de la interfaz radio más importante de esta generación, la 3.9G, se hará una overview general de cómo han ido evolucionando las comunicaciones móviles a lo largo de la historia, se analizarán las características de la tecnología móvil actual, la 3.9G, para posteriormente centrarse en un par de simuladores que demostrarán, mediante resultados gráficos, estas características. Hoy en día, el uso de estos simuladores es totalmente necesario, ya que las comunicaciones móviles, avanzan a un ritmo vertiginoso y es necesario por lo tanto conocer las prestaciones que pueden producir las diferentes tecnologías móviles utilizadas. Los simuladores utilizados por este proyecto, permiten analizar el comportamiento de varios escenarios, ya que existen diferentes tipos de simuladores, tanto a nivel de enlace como a nivel de sistema. Se mencionarán una serie de simuladores correspondientes a la tercera generación UMTS, pero los simuladores en cuestión que se estudiarán y analizarán con más profundidad en este proyecto fin de carrera son los simuladores “Link-Level” y “System-Level”, desarrollados por el “Institute of Communications and Radio-Frecuency Engineering” de la Universidad de Viena. Estos simuladores permiten realizar diferentes simulaciones, como analizar el comportamiento entre una estación base y un único usuario, para el caso de los simuladores a nivel de enlace, o bien analizar el comportamiento de toda una red en el caso de los simuladores a nivel de sistema. Con los resultados que se pueden obtener de ambos simuladores, se realizarán una serie de preguntas, basadas en la práctica realizada por el profesor de la universidad Politécnica de Madrid, Pedro García del Pino, tanto de tipo teóricas como de tipo prácticas, para comprobar que se han entendido los simuladores analizados. Finalmente se citarán las conclusiones que se obtiene de este proyecto, así como las líneas futuras de acción. PROJECT ABSTRACT This project includes the study of different simulators on mobile communications, which are responsible for analyzing the behavior of UMTS (Universal Mobile Telecommunications System), 3G and LTE (Long Term Evolution), 3.9G, mainly focusing on the case of LTE simulators because it is the technology that is being implemented today. Therefore, before analyzing the characteristics of the most important radio interface of this generation, 3.9G, there will give a general overview how the mobile communications have evolved throughout history, analyzing the characteristics of current mobile technology, the 3.9G, later focus on a pair of simulators that demonstrate through graphical results, these characteristics. Today, the use of these simulators is absolutely necessary, because mobile communications advance at a high rate, and it is necessary to know the features that can produce different mobile technologies that are used. The simulators used for this project, allow to analyze the behavior of several scenarios, as there are different types of simulators, both link and system level. It mentioned a number of simulators for the third generation UMTS, but the simulators in question to be studied and analyzed in this final project are the simulators "Link-Level" and "System-Level", developed by the "Institute of Communications and Radio-Frequency Engineering" at the University of Vienna. These simulators allow realize different simulations, analyze the behavior between a base station and a single user, in the case of the link-level simulators or analyze the performance of a network in the case of system-level simulators. With the results that can be obtained from both simulators, will perform a series of questions, based on the practice developed by Pedro García del Pino, Professor of “Universidad Politécnica de Madrid (UPM)”. These questions will be both of a theoretical and practical type, to check that have been understood the analyzed simulators. Finally, it quotes the conclusions obtained from this project and mention the future lines of action.

Sistema de telemetría para un vehículo de fórmula S.A.E.

En este proyecto, se ha desarrollado una aplicación electrónica para un coche de competición, en concreto para la fórmula SAE (Society of Automotive Engineers), una competición universitaria en la que cada equipo, formado por estudiantes, debe diseñar, construir y probar un prototipo basándose en una serie de reglas. El objetivo final de la competición es proporcionar a los estudiantes el conocimiento práctico necesario para su futura labor profesional, del cual se pensaba que los estudiantes adolecían al acabar sus estudios universitarios cuando se creó esta competición. La aplicación desarrollada en este proyecto consiste en un sistema de telemetría, utilizado para transmitir los datos proporcionados por los sensores del vehículo a través de un sistema de radiofrecuencia, de manera que se pueda estudiar el comportamiento del coche durante los ensayos a la vez que el coche está rodando y así no depender de un sistema de adquisición de datos del que había que descargarse la información una vez finalizada la sesión de ensayo, como había que hacer hasta el momento. Para la implementación del proyecto, se ha utilizado un kit de desarrollo (Xbee Pro 868) que incluye dos módulos de radio, dos placas de desarrollo, dos cables USB y una antena, el cual ha permitido desarrollar la parte de radio del proyecto. Para transmitir los datos proporcionados por la centralita del vehículo, la cual recoge la información de todos los sensores presentes en el vehículo, se han desarrollado dos placas de circuito impreso. La primera de ellas tiene como elemento principal un microprocesador PIC de la marca Microchip (PIC24HJ64GP502), que recoge los datos proporcionados por la centralita del vehículo a través de su bus CAN de comunicaciones. La segunda placa de circuito impreso tiene como elemento fundamental el transmisor de radio. Dicho transmisor está conectado al microprocesador de la otra placa a través de línea serie. Como receptor de radio se ha utilizado una de las placas de prueba que integraba el kit de desarrollo Xbee Pro 868, la cual recoge los datos que han sido enviados vía radio y los manda a su vez a través de USB a un ordenador donde son monitorizados. Hasta aquí la parte hardware del sistema. En cuanto a la parte software, ha habido que desarrollar una aplicación en lenguaje C, que ejecuta el microprocesador PIC, que se encarga de recoger los datos enviados por la centralita a través del bus CAN (Controller Area Network) y transmitirlos a través de línea serie al chip de radio. Por último, para la monitorización de los datos se han desarrollado dos aplicaciones en LabVIEW, una que recoge los datos a través de USB, los muestra en pantalla y los guarda en un fichero y otra que lee los datos del fichero y los representa gráficamente para permitir un estudio más detallado del comportamiento del vehículo. ABSTRACT In this project, an electronic application has been developed for a race car – Formula SAE car-. Formula SAE is a university championship in which each team, made up of students, should design, construct and test a prototype within certain rules. The final goal of the competition is to enhance the practical knowledge of the students, which was thougth to be poor at the time the competition was created. The application developed in this project consists of a telemetry system, employed to transmit the data provided by the car’s sensors through a radio frequency system, so that it could be possible to study the behaviour of the vehicle during tests and do not depend on a datalogger system as it occurred until now. To carry out the radio module of the project, a Xbee Pro 868 development kit has been used, which includes two radio modules, two development boards, two USB cables and an antenna. To transmit the data provided by the ECU (Engine Control Unit) of the vehicle, which receives information from all the sensors the vehicle has, two printed circuit boards have been built. One of them has a PIC microprocessor of Microchip (PIC24HJ64GP502) which receives the data coming from CAN bus of the ECU. Tha main element of the other printed circuit board is the radio transmitter. This chip receives the data from the microprocessor through its serial line. The development board of the Xbee Pro 868 has been used as receiver. When data arrives to the receiver, it transmits them to a computer through USB where the data are displayed. All this composes the hardware of the system. Regarding the software, a C coded application has been developed. This application is executed by the microprocessor and its function is to receive the data from the bus CAN (Controller Area Network) and send them to the radio transmitter through the microprocessor’s serial line. To show the data on the computer, two LabVIEW applications has been developed. The first one receives the data through the USB port, displays them on the screen and save them to a file and the second one reads the data from the file while represents them graphically to allow studying the behaviour of the car on track.

Positional Accuracy in Smart-Phones and Its Effect on LBS Applications.

Location-based services (LBS) highly rely on the location of the mobile user in order to provide the service tailored to that location. This location is calculated differently depending on the technology available in the used mobile device. No matter which technology is used, the location will never be calculated 100% correctly; instead there will always be a margin of error generated during the calculation, which is referred to as positional accuracy. This research has reviewed the eight most common positioning technologies available in the major current smart-phones and assessed their positional accuracy with respect to its usage by LBS applications. Given the vast majority of these applications, this research classified them into thirteen categories, and these categories were also classified depending on their level criticality as low, medium, or high critical, and whether they function indoor or outdoor. The accuracies of different positioning technologies are compared to these two criteria. Low critical outdoor and high critical indoor applications were found technologically covered; high and medium critical outdoor ones weren?t fully resolved. Finally three potential solutions are suggested to be implemented in future smartphones to resolve this technological gap: Real-Time Kinematics Global Positioning System (RTK GPS), terrestrial transmitters, and combination of Wireless Sensors Network and Radio Frequency Identification (WSN-RFID).

The counteractive effect of the sensor housing on the unit sensitivity across a series of dynamic temperature profiles.

The advantages of wireless sensing implemented on the cold chain of fresh products are well known. These sensor systems consist of a combination of delicate internal electronic circuitry enclosed in a special housing unit. Manufacturers however are presented with the challenge that the housing required to withstand the harsh environment in which the sensors are being used all too often take from the functionality of the sensor. Therefore the target of this study is to determine the dynamic behavior and the counteractive effects of the sensor housing on temperature recording accuracy in the wireless nodes of Wireless Sensor Network (WSN) and Radio Frequency Identification (RFID) semi-passive tags. Two kind of semi-passive Turbo Tags were used (T700 and T702-B), which consisted of sensors with and without a cover, and two kind of WSN nodes, IRIS (sensors Intersema and Sensirion soldered in the motherboard) and NLAZA (Sensirion in a cable and soldered to the motherboard). To recreate the temperature profiles the devices were rotated between a cold room(5 ºC) through a ambient room(23 ºC) to a heated environment (35ºC) and vice versa. Analysis revealed the differences between housing and no housing are 308.22s to 21.99s respectively in the step from 5 to 35 ºC. As is demonstrated in these experiments the influence of the housing significantly hinders sensor accuracy.

Advanced Characterisation of a Coffee Fermenting Tank by Multi-distributed Wireless Sensors: Spatial Interpolation and Phase Space Graphs

The fermentation stage is considered to be one of the critical steps in coffee processing due to its impact on the final quality of the product. The objective of this work is to characterise the temperature gradients in a fermentation tank by multi-distributed, low-cost and autonomous wireless sensors (23 semi-passive TurboTag® radio-frequency identifier (RFID) temperature loggers). Spatial interpolation in polar coordinates and an innovative methodology based on phase space diagrams are used. A real coffee fermentation process was supervised in the Cauca region (Colombia) with sensors submerged directly in the fermenting mass, leading to a 4.6 °C temperature range within the fermentation process. Spatial interpolation shows a maximum instant radial temperature gradient of 0.1 °C/cm from the centre to the perimeter of the tank and a vertical temperature gradient of 0.25 °C/cm for sensors with equal polar coordinates. The combination of spatial interpolation and phase space graphs consistently enables the identification of five local behaviours during fermentation (hot and cold spots).

Wide bandwidth envelope trackers with reduced switching frequency for RF power amplifier

El requerimiento de proveer alta frecuencia de datos en los modernos sistema de comunicación inalámbricos resulta en complejas señales moduladas de radio-frequencia (RF) con un gran ancho de banda y alto ratio pico-promedio (PAPR). Para garantizar la linealidad del comportamiento, los amplificadores lineales de potencia comunes funcionan típicamente entre 4 y 10 dB de back-o_ desde la máxima potencia de salida, ocasionando una baja eficiencia del sistema. La eliminación y restauración de la evolvente (EER) y el seguimiento de la evolvente (ET) son dos prometedoras técnicas para resolver el problema de la eficiencia. Tanto en EER como en ET, es complicado diseñar un amplificador de potencia que sea eficiente para señales de RF de alto ancho de banda y alto PAPR. Una propuesta común para los amplificadores de potencia es incluir un convertidor de potencia de muy alta eficiencia operando a frecuencias más altas que el ancho de banda de la señal RF. En este caso, la potencia perdida del convertidor ocasionado por la alta frecuencia desaconseja su práctica cuando el ancho de banda es muy alto. La solución a este problema es el enfoque de esta disertación que presenta dos arquitecturas de amplificador evolvente: convertidor híbrido-serie con una técnica de evolvente lenta y un convertidor multinivel basado en un convertidor reductor multifase con control de tiempo mínimo. En la primera arquitectura, una topología híbrida está compuesta de una convertidor reductor conmutado y un regulador lineal en serie que trabajan juntos para ajustar la tensión de salida para seguir a la evolvente con precisión. Un algoritmo de generación de una evolvente lenta crea una forma de onda con una pendiente limitada que es menor que la pendiente máxima de la evolvente original. La salida del convertidor reductor sigue esa forma de onda en vez de la evolvente original usando una menor frecuencia de conmutación, porque la forma de onda no sólo tiene una pendiente reducida sino también un menor ancho de banda. De esta forma, el regulador lineal se usa para filtrar la forma de onda tiene una pérdida de potencia adicional. Dependiendo de cuánto se puede reducir la pendiente de la evolvente para producir la forma de onda, existe un trade-off entre la pérdida de potencia del convertidor reductor relacionada con la frecuencia de conmutación y el regulador lineal. El punto óptimo referido a la menor pérdida de potencia total del amplificador de evolvente es capaz de identificarse con la ayuda de modelo preciso de pérdidas que es una combinación de modelos comportamentales y analíticos de pérdidas. Además, se analiza el efecto en la respuesta del filtro de salida del convertidor reductor. Un filtro de dampeo paralelo extra es necesario para eliminar la oscilación resonante del filtro de salida porque el convertidor reductor opera en lazo abierto. La segunda arquitectura es un amplificador de evolvente de seguimiento de tensión multinivel. Al contrario que los convertidores que usan multi-fuentes, un convertidor reductor multifase se emplea para generar la tensión multinivel. En régimen permanente, el convertidor reductor opera en puntos del ciclo de trabajo con cancelación completa del rizado. El número de niveles de tensión es igual al número de fases de acuerdo a las características del entrelazamiento del convertidor reductor. En la transición, un control de tiempo mínimo (MTC) para convertidores multifase es novedosamente propuesto y desarrollado para cambiar la tensión de salida del convertidor reductor entre diferentes niveles. A diferencia de controles convencionales de tiempo mínimo para convertidores multifase con inductancia equivalente, el propuesto MTC considera el rizado de corriente por cada fase basado en un desfase fijo que resulta en diferentes esquemas de control entre las fases. La ventaja de este control es que todas las corrientes vuelven a su fase en régimen permanente después de la transición para que la siguiente transición pueda empezar muy pronto, lo que es muy favorable para la aplicación de seguimiento de tensión multinivel. Además, el control es independiente de la carga y no es afectado por corrientes de fase desbalanceadas. Al igual que en la primera arquitectura, hay una etapa lineal con la misma función, conectada en serie con el convertidor reductor multifase. Dado que tanto el régimen permanente como el estado de transición del convertidor no están fuertemente relacionados con la frecuencia de conmutación, la frecuencia de conmutación puede ser reducida para el alto ancho de banda de la evolvente, la cual es la principal consideración de esta arquitectura. La optimización de la segunda arquitectura para más alto anchos de banda de la evolvente es presentada incluyendo el diseño del filtro de salida, la frecuencia de conmutación y el número de fases. El área de diseño del filtro está restringido por la transición rápida y el mínimo pulso del hardware. La rápida transición necesita un filtro pequeño pero la limitación del pulso mínimo del hardware lleva el diseño en el sentido contrario. La frecuencia de conmutación del convertidor afecta principalmente a la limitación del mínimo pulso y a las pérdidas de potencia. Con una menor frecuencia de conmutación, el ancho de pulso en la transición es más pequeño. El número de fases relativo a la aplicación específica puede ser optimizado en términos de la eficiencia global. Otro aspecto de la optimización es mejorar la estrategia de control. La transición permite seguir algunas partes de la evolvente que son más rápidas de lo que el hardware puede soportar al precio de complejidad. El nuevo método de sincronización de la transición incrementa la frecuencia de la transición, permitiendo que la tensión multinivel esté más cerca de la evolvente. Ambas estrategias permiten que el convertidor pueda seguir una evolvente con un ancho de banda más alto que la limitación de la etapa de potencia. El modelo de pérdidas del amplificador de evolvente se ha detallado y validado mediante medidas. El mecanismo de pérdidas de potencia del convertidor reductor tiene que incluir las transiciones en tiempo real, lo cual es diferente del clásico modelos de pérdidas de un convertidor reductor síncrono. Este modelo estima la eficiencia del sistema y juega un papel muy importante en el proceso de optimización. Finalmente, la segunda arquitectura del amplificador de evolvente se integra con el amplificador de clase F. La medida del sistema EER prueba el ahorro de energía con el amplificador de evolvente propuesto sin perjudicar la linealidad del sistema. ABSTRACT The requirement of delivering high data rates in modern wireless communication systems results in complex modulated RF signals with wide bandwidth and high peak-to-average ratio (PAPR). In order to guarantee the linearity performance, the conventional linear power amplifiers typically work at 4 to 10 dB back-off from the maximum output power, leading to low system efficiency. The envelope elimination and restoration (EER) and envelope tracking (ET) are two promising techniques to overcome the efficiency problem. In both EER and ET, it is challenging to design efficient envelope amplifier for wide bandwidth and high PAPR RF signals. An usual approach for envelope amplifier includes a high-efficiency switching power converter operating at a frequency higher than the RF signal's bandwidth. In this case, the power loss of converter caused by high switching operation becomes unbearable for system efficiency when signal bandwidth is very wide. The solution of this problem is the focus of this dissertation that presents two architectures of envelope amplifier: a hybrid series converter with slow-envelope technique and a multilevel converter based on a multiphase buck converter with the minimum time control. In the first architecture, a hybrid topology is composed of a switched buck converter and a linear regulator in series that work together to adjust the output voltage to track the envelope with accuracy. A slow envelope generation algorithm yields a waveform with limited slew rate that is lower than the maximum slew rate of the original envelope. The buck converter's output follows this waveform instead of the original envelope using lower switching frequency, because the waveform has not only reduced slew rate but also reduced bandwidth. In this way, the linear regulator used to filter the waveform has additional power loss. Depending on how much reduction of the slew rate of envelope in order to obtain that waveform, there is a trade-off between the power loss of buck converter related to the switching frequency and the power loss of linear regulator. The optimal point referring to the lowest total power loss of this envelope amplifier is identified with the help of a precise power loss model that is a combination of behavioral and analytic loss model. In addition, the output filter's effect on the response is analyzed. An extra parallel damping filter is needed to eliminate the resonant oscillation of output filter L and C, because the buck converter operates in open loop. The second architecture is a multilevel voltage tracking envelope amplifier. Unlike the converters using multi-sources, a multiphase buck converter is employed to generate the multilevel voltage. In the steady state, the buck converter operates at complete ripple cancellation points of duty cycle. The number of the voltage levels is equal to the number of phases according the characteristics of interleaved buck converter. In the transition, a minimum time control (MTC) for multiphase converter is originally proposed and developed for changing the output voltage of buck converter between different levels. As opposed to conventional minimum time control for multiphase converter with equivalent inductance, the proposed MTC considers the current ripple of each phase based on the fixed phase shift resulting in different control schemes among the phases. The advantage of this control is that all the phase current return to the steady state after the transition so that the next transition can be triggered very soon, which is very favorable for the application of multilevel voltage tracking. Besides, the control is independent on the load condition and not affected by the unbalance of phase current. Like the first architecture, there is also a linear stage with the same function, connected in series with the multiphase buck converter. Since both steady state and transition state of the converter are not strongly related to the switching frequency, it can be reduced for wide bandwidth envelope which is the main consideration of this architecture. The optimization of the second architecture for wider bandwidth envelope is presented including the output filter design, switching frequency and the number of phases. The filter design area is restrained by fast transition and the minimum pulse of hardware. The fast transition needs small filter but the minimum pulse of hardware limitation pushes the filter in opposite way. The converter switching frequency mainly affects the minimum pulse limitation and the power loss. With lower switching frequency, the pulse width in the transition is smaller. The number of phases related to specific application can be optimized in terms of overall efficiency. Another aspect of optimization is improving control strategy. Transition shift allows tracking some parts of envelope that are faster than the hardware can support at the price of complexity. The new transition synchronization method increases the frequency of transition, allowing the multilevel voltage to be closer to the envelope. Both control strategies push the converter to track wider bandwidth envelope than the limitation of power stage. The power loss model of envelope amplifier is detailed and validated by measurements. The power loss mechanism of buck converter has to include the transitions in real time operation, which is different from classical power loss model of synchronous buck converter. This model estimates the system efficiency and play a very important role in optimization process. Finally, the second envelope amplifier architecture is integrated with a Class F amplifier. EER system measurement proves the power saving with the proposed envelope amplifier without disrupting the linearity performance.

Ultra Low Power FPGA-Based Architecture for Wake-up Radio in Wireless Sensor Networks

In this paper the capabilities of ultra low power FPGAs to implement Wake-up Radios (WuR) for ultra low energy Wireless Sensor Networks (WSNs) are analyzed. The main goal is to evaluate the utilization of very low power configurable devices to take advantage of their speed, flexibility and low power consumption instead of the more common approaches based on ASICs or microcontrollers. In this context, energy efficiency is a key aspect, considering that usually the instant power consumption is considered a figure of merit, more than the total energy consumed by the application.