Methods for noise reduction in far-field patterns obtained from cylindrical near-field antenna measurements

Two different methods to reduce the noise power in the far-field pattern of an antenna as measured in cylindrical near-field (CNF) are proposed. Both methods are based on the same principle: the data recorded in the CNF measurement, assumed to be corrupted by white Gaussian and space-stationary noise, are transformed into a new domain where it is possible to filter out a portion of noise. Those filtered data are then used to calculate a far-field pattern with less noise power than that one obtained from the measured data without applying any filtering. Statistical analyses are carried out to deduce the expressions of the signal-to-noise ratio improvement achieved with each method. Although the idea of the two alternatives is the same, there are important differences between them. The first one applies a modal filtering, requires an oversampling and improves the far-field pattern in all directions. The second method employs a spatial filtering on the antenna plane, does not require oversampling and the far-field pattern is only improved in the forward hemisphere. Several examples are presented using both simulated and measured near-field data to verify the effectiveness of the methods.

Analytical evaluation of uncertainty on active antenna arrays

An analytical method for evaluating the uncertainty of the performance of active antenna arrays in the whole spatial spectrum is presented. Since array processing algorithms based on spatial reference are widely used to track moving targets, it is essential to be aware of the impact of the uncertainty sources on the antenna response. Furthermore, the estimation of the direction of arrival (DOA) depends on the array uncertainty. The aim of the uncertainties analysis is to provide an exhaustive characterization of the behavior of the active antenna array associated with its main uncertainty sources. The result of this analysis helps to select the proper calibration technique to be implemented. An illustrative example for a triangular antenna array used for satellite tracking is presented showing the suitability of the proposed method to carry out an efficient characterization of an active antenna array.

Calibration proposal for new antenna array architectures and technologies for space communications

In large antenna arrays with a large number of antenna elements, the required number of measurements for the characterization of the antenna array is very demanding in cost and time. This letter presents a new offline calibration process for active antenna arrays that reduces the number of measurements by subarray-level characterization. This letter embraces measurements, characterization, and calibration as a global procedure assessing about the most adequate calibration technique and computing of compensation matrices. The procedure has been fully validated with measurements of a 45-element triangular panel array designed for Low Earth Orbit (LEO) satellite tracking that compensates the degradation due to gain and phase imbalances and mutual coupling.

A hands-on education project: antenna design for inter-CubeSat communications

CubeSat platforms have become a de facto standard for universities willing to initiate space-technology activities with students. These small satellite platforms ease the implementation of hands-on education projects and opening the apertures of new research areas. Moreover, due to the limited volume (a 10 cm cube) and power (1 W), the application of imaginative solutions is mandatory. This leads to new innovation processes in the course of CubeSat projects. In this paper, we present a hands-on education project the aim of which is the specification, design, building and measurement of an antenna for communication between nanosatellites and, in particular, CubeSats. The project lies within the framework of ETSIT-UPM innovative education activities in the area of space technology, where students play a leading role in real engineering projects.

Study of an electronic steering antenna with a staggered phase shifter configuration

This paper presents a study of three possible solutions that can be taken into account to control the phase shift between elements in an antenna array. Because commercial digital phase shifters have become a strategic element by U.S. Government, these elements have increased their price. For this reason, it is necessary to adopt some solutions that allow us to deal with the design and construction of antenna arrays.

Novel Gravity Distortion Evaluation on Large Antenna Array for Deep Space Communication

This paper presents a simple gravity evaluation model for large reflector antennas and the experimental example for a case study of one uplink array of 4x35-m antennas at X and Ka band. This model can be used to evaluate the gain reduction as a function of the maximum gravity distortion, and also to specify this at system designer level. The case study consists of one array of 35-m antennas for deep space missions. Main issues due to the gravity effect have been explored with Monte Carlo based simulation analysis.

Calibration process on the study of new antenna array architectures for space communications

This paper introduces novel calibration processes applied to antenna arrays with new architectures and technologies designed to improve the performance of traditional earth stations for satellite communications due to the increasing requirement of data capacity during last decades. Besides, the Radiation Group from the Technical University of Madrid has been working on the development of new antenna arrays based on novel architecture and technologies along many projects as a solution for the ground segment in the early future. Nowadays, the calibration process is an interesting and cutting edge research field in a period of expansion with a lot of work to do for calibration in transmission and also for reception of these novel antennas under development.

Research activities of Spanish antenna groups

When we look at the history of electricity and electromagnetism in Spain we discover that the most important Spanish researchers are generally out of the official institutions or stable research groups until the 20th century [1] [2]. In the 20th century most of the scientific research is done in stable research institutions and universities and the most important electromagnetism research centres in Spain are located in the Faculty of Physics of the most important universities, the National Scientific Research Council (CSIC) and the School for Telecommunication Engineering created in 1923. But the greatest impulse of research in the antenna and radiowave propagation field is done after 1960 reaching the first national URSI conference in 1980. After that year, the relation between groups and the number of research groups is continuously growing and the relation to industry is also increasing. When Spain joins the European research organizations (COST, ERC...) and the European Union in 1985 the research support experience a fast growing and the participation in the European research structures. In the antenna design field, there exist some specializations although most of the groups have dome specific projects in almost all the antenna analysis and design fields. Here, we have selected the most important and characteristic area related to each of the research groups and institutions. The easiest way to classify the research work in antennas is the selection between antenna analysis, design and measurement. After that the selected frequency bands technology, the type of antennas and the related circuits can be a good criterion to describe the variety of research work and specialization between groups.

Application of postprocessing techniques methods for noise reduction in cylindrical near field antenna measurements

Three different methods to reduce the noise power in the far-field pattern of an antenna when it is measured in a cylindrical near field system are presented and compared. The first one is based on a modal filtering while the other two are based on spatial filtering, either on an antenna plane or either on a cylinder of smaller radius. Simulated and measured results will be presented.

Bifocal reflector antenna system for radar imaging at 300 GHz

A 300 GHz radar imaging system is presented, including descriptions of the radar sensor and antenna subsystems. The antenna consists of a Bifocal Ellipsoidal Gregorian Reflector whose beam is scanned by a combination of the rotation and vertical tilting of a flat small secondary mirror. A prototype is being mounted and its characterization will be presented.

Sistema de telemetría para un vehículo de fórmula S.A.E.

En este proyecto, se ha desarrollado una aplicación electrónica para un coche de competición, en concreto para la fórmula SAE (Society of Automotive Engineers), una competición universitaria en la que cada equipo, formado por estudiantes, debe diseñar, construir y probar un prototipo basándose en una serie de reglas. El objetivo final de la competición es proporcionar a los estudiantes el conocimiento práctico necesario para su futura labor profesional, del cual se pensaba que los estudiantes adolecían al acabar sus estudios universitarios cuando se creó esta competición. La aplicación desarrollada en este proyecto consiste en un sistema de telemetría, utilizado para transmitir los datos proporcionados por los sensores del vehículo a través de un sistema de radiofrecuencia, de manera que se pueda estudiar el comportamiento del coche durante los ensayos a la vez que el coche está rodando y así no depender de un sistema de adquisición de datos del que había que descargarse la información una vez finalizada la sesión de ensayo, como había que hacer hasta el momento. Para la implementación del proyecto, se ha utilizado un kit de desarrollo (Xbee Pro 868) que incluye dos módulos de radio, dos placas de desarrollo, dos cables USB y una antena, el cual ha permitido desarrollar la parte de radio del proyecto. Para transmitir los datos proporcionados por la centralita del vehículo, la cual recoge la información de todos los sensores presentes en el vehículo, se han desarrollado dos placas de circuito impreso. La primera de ellas tiene como elemento principal un microprocesador PIC de la marca Microchip (PIC24HJ64GP502), que recoge los datos proporcionados por la centralita del vehículo a través de su bus CAN de comunicaciones. La segunda placa de circuito impreso tiene como elemento fundamental el transmisor de radio. Dicho transmisor está conectado al microprocesador de la otra placa a través de línea serie. Como receptor de radio se ha utilizado una de las placas de prueba que integraba el kit de desarrollo Xbee Pro 868, la cual recoge los datos que han sido enviados vía radio y los manda a su vez a través de USB a un ordenador donde son monitorizados. Hasta aquí la parte hardware del sistema. En cuanto a la parte software, ha habido que desarrollar una aplicación en lenguaje C, que ejecuta el microprocesador PIC, que se encarga de recoger los datos enviados por la centralita a través del bus CAN (Controller Area Network) y transmitirlos a través de línea serie al chip de radio. Por último, para la monitorización de los datos se han desarrollado dos aplicaciones en LabVIEW, una que recoge los datos a través de USB, los muestra en pantalla y los guarda en un fichero y otra que lee los datos del fichero y los representa gráficamente para permitir un estudio más detallado del comportamiento del vehículo. ABSTRACT In this project, an electronic application has been developed for a race car – Formula SAE car-. Formula SAE is a university championship in which each team, made up of students, should design, construct and test a prototype within certain rules. The final goal of the competition is to enhance the practical knowledge of the students, which was thougth to be poor at the time the competition was created. The application developed in this project consists of a telemetry system, employed to transmit the data provided by the car’s sensors through a radio frequency system, so that it could be possible to study the behaviour of the vehicle during tests and do not depend on a datalogger system as it occurred until now. To carry out the radio module of the project, a Xbee Pro 868 development kit has been used, which includes two radio modules, two development boards, two USB cables and an antenna. To transmit the data provided by the ECU (Engine Control Unit) of the vehicle, which receives information from all the sensors the vehicle has, two printed circuit boards have been built. One of them has a PIC microprocessor of Microchip (PIC24HJ64GP502) which receives the data coming from CAN bus of the ECU. Tha main element of the other printed circuit board is the radio transmitter. This chip receives the data from the microprocessor through its serial line. The development board of the Xbee Pro 868 has been used as receiver. When data arrives to the receiver, it transmits them to a computer through USB where the data are displayed. All this composes the hardware of the system. Regarding the software, a C coded application has been developed. This application is executed by the microprocessor and its function is to receive the data from the bus CAN (Controller Area Network) and send them to the radio transmitter through the microprocessor’s serial line. To show the data on the computer, two LabVIEW applications has been developed. The first one receives the data through the USB port, displays them on the screen and save them to a file and the second one reads the data from the file while represents them graphically to allow studying the behaviour of the car on track.

Contribución al desarrollo de técnicas CAD para el diseño de antenas impresas y dispositivos pasivos de microondas basadas en el método de elementos finitos

El objetivo principal de esta tesis es el desarrollo de herramientas numéricas basadas en técnicas de onda completa para el diseño asistido por ordenador (Computer-Aided Design,‘CAD’) de dispositivos de microondas. En este contexto, se desarrolla una herramienta numérica basada en el método de los elementos finitos para el diseño y análisis de antenas impresas mediante algoritmos de optimización. Esta técnica consiste en dividir el análisis de una antena en dos partes. Una parte de análisis 3D que se realiza sólo una vez en cada punto de frecuencia de la banda de funcionamiento donde se sustituye una superficie que contiene la metalización del parche por puertas artificiales. En una segunda parte se inserta entre las puertas artificiales en la estructura 3D la superficie soportando una metalización y se procede un análisis 2D para caracterizar el comportamiento de la antena. La técnica propuesta en esta tesis se puede implementar en un algoritmo de optimización para definir el perfil de la antena que permite conseguir los objetivos del diseño. Se valida experimentalmente dicha técnica empleándola en el diseño de antenas impresas de banda ancha para diferentes aplicaciones mediante la optimización del perfil de los parches. También, se desarrolla en esta tesis un procedimiento basado en el método de descomposición de dominio y el método de los elementos finitos para el diseño de dispositivos pasivos de microonda. Se utiliza este procedimiento en particular para el diseño y sintonía de filtros de microondas. En la primera etapa de su aplicación se divide la estructura que se quiere analizar en subdominios aplicando el método de descomposición de dominio, este proceso permite analizar cada segmento por separado utilizando el método de análisis adecuado dado que suele haber subdominios que se pueden analizar mediante métodos analíticos por lo que el tiempo de análisis es más reducido. Se utilizan métodos numéricos para analizar los subdominios que no se pueden analizar mediante métodos analíticos. En esta tesis, se utiliza el método de los elementos finitos para llevar a cabo el análisis. Además de la descomposición de dominio, se aplica un proceso de barrido en frecuencia para reducir los tiempos del análisis. Como método de orden reducido se utiliza la técnica de bases reducidas. Se ha utilizado este procedimiento para diseñar y sintonizar varios ejemplos de filtros con el fin de comprobar la validez de dicho procedimiento. Los resultados obtenidos demuestran la utilidad de este procedimiento y confirman su rigurosidad, precisión y eficiencia en el diseño de filtros de microondas. ABSTRACT The main objective of this thesis is the development of numerical tools based on full-wave techniques for computer-aided design ‘CAD’ of microwave devices. In this context, a numerical technique based on the finite element method ‘FEM’ for the design and analysis of printed antennas using optimization algorithms has been developed. The proposed technique consists in dividing the analysis of the antenna in two stages. In the first stage, the regions of the antenna which do not need to be modified during the CAD process are initially characterized only once from their corresponding matrix transfer function (Generalized Admittance matrix, ‘GAM’). The regions which will be modified are defined as artificial ports, precisely the regions which will contain the conducting surfaces of the printed antenna. In a second stage, the contour shape of the conducting surfaces of the printed antenna is iteratively modified in order to achieve a desired electromagnetic performance of the antenna. In this way, a new GAM of the radiating device which takes into account each printed antenna shape is computed after each iteration. The proposed technique can be implemented with a genetic algorithm to achieve the design objectives. This technique is validated experimentally and applied to the design of wideband printed antennas for different applications by optimizing the shape of the radiating device. In addition, a procedure based on the domain decomposition method and the finite element method has been developed for the design of microwave passive devices. In particular, this procedure can be applied to the design and tune of microwave filters. In the first stage of its implementation, the structure to be analyzed is divided into subdomains using the domain decomposition method; this process allows each subdomains can be analyzed separately using suitable analysis method, since there is usually subdomains that can be analyzed by analytical methods so that the time of analysis is reduced. For analyzing the subdomains that cannot be analyzed by analytical methods, we use the numerical methods. In this thesis, the FEM is used to carry out the analysis. Furthermore the decomposition of the domain, a frequency sweep process is applied to reduce analysis times. The reduced order model as the reduced basis technique is used in this procedure. This procedure is applied to the design and tune of several examples of microwave filters in order to check its validity. The obtained results allow concluding the usefulness of this procedure and confirming their thoroughness, accuracy and efficiency for the design of microwave filters.

Man-pack antenna at X-band

In this paper a low cost man-pack antenna for satellite communications at X band is presented. The antenna has dual circular polarization in Tx and Rx.

On the design of a planar phased array radar antenna architecture for space debris situational awareness

The Space Situational Awareness (SSA) program from the European Space Agency (ESA) protects Europe's citizens and their satellite-based services by detecting space hazards. ESA Ground Systems (GS) division is currently designing a phased array radar composed of thousands of radiating elements for future stages of the SSA program [1]. The radar shall guarantee the detection of most of the Low Earth Orbit (LEO) space debris, providing a general map of space junk. While range accuracy is mainly dictated by the radar waveform, the detection and tracking of small objects in LEO regimes is highly dependent on the angular accuracy achieved by the smart phased array antenna, demonstrating the important of the performance of this architecture.

GEODA-SARAS: Multi-Phased array planar antenna for satellite communications

Nowadays, earth stations have as a common feature the use of large reflector antenna for downloading data from satellites. Large reflectors have impairments such as mechanical complexity, low flexibility and high cost. Thus, the feasibility of other antenna technologies must be evaluated, such as conformal adaptive antennas based on multiple planar active arrays. In the scenery under study, the capability to track several satellites simultaneously, higher flexibility, lower production and maintenance cost, modularity and a more efficient use of the spectrum; are the most important advantage to boost up active antenna arrays over large dishes.