Design and analysis of helium Brayton power cycles for HiPER reactor

Helium Brayton cycles have been studied as power cycles for both fission and fusion reactors obtaining high thermal efficiency. This paper studies several technological schemes of helium Brayton cycles applied for the HiPER reactor proposal. Since HiPER integrates technologies available at short term, its working conditions results in a very low maximum temperature of the energy sources, something that limits the thermal performance of the cycle. The aim of this work is to analyze the potential of the helium Brayton cycles as power cycles for HiPER. Several helium Brayton cycle configurations have been investigated with the purpose of raising the cycle thermal efficiency under the working conditions of HiPER. The effects of inter-cooling and reheating have specifically been studied. Sensitivity analyses of the key cycle parameters and component performances on the maximum thermal efficiency have also been carried out. The addition of several inter-cooling stages in a helium Brayton cycle has allowed obtaining a maximum thermal efficiency of over 36%, and the inclusion of a reheating process may also yield an added increase of nearly 1 percentage point to reach 37%. These results confirm that helium Brayton cycles are to be considered among the power cycle candidates for HiPER.

Silica final lens performance in laser fusion facilities: HiPER and LIFE

Nowadays, the projects LIFE (Laser Inertial Fusion Energy) in USA and HiPER (High Power Laser Energy Research) in Europe are the most advanced ones to demonstrate laser fusion energy viability. One of the main points of concern to properly achieve ignition is the performance of the final optics (lenses) under the severe irradiation conditions that take place in fusion facilities. In this paper, we calculate the radiation fluxes and doses as well as the radiation-induced temperature enhancement and colour centre formation in final lenses assuming realistic geometrical configurations for HiPER and LIFE. On these bases, the mechanical stresses generated by the established temperature gradients are evaluated showing that from a mechanical point of view lenses only fulfil specifications if ions resulting from the imploding target are mitigated. The absorption coefficient of the lenses is calculated during reactor startup and steady-state operation. The obtained results reveal the necessity of new solutions to tackle ignition problems during the startup process for HiPER. Finally, we evaluate the effect of temperature gradients on focal length changes and lens surface deformations. In summary, we discuss the capabilities and weak points of silica lenses and propose alternatives to overcome predictable problems

Neutronics and activation of the preliminary reaction chamber of HiPER reactor based in a SCLL blanket

The HiPER reactor design is exploring different reaction chambers. In this study, we tackle the neutronicsand activation studies of a preliminary reaction chamber based in the following technologies: unpro-tected dry wall for the First Wall, self-cooled lead lithium blanket, and independent low activation steelVacuum Vessel. The most critical free parameter in this stage is the blanket thickness, as a function ofthe6Li enrichment. After a parametric study, we select for study both a ?thin? and ?thick? blanket, with?high? and ?low?6Li enrichment respectively, to reach a TBR = 1.1. To help to make a choice, we com-pute, for both blanket options, in addition to the TBR, the energy amplification factor, the tritium partialpressure, the203Hg and210Po total activity in the LiPb loop, and the Vacuum Vessel thickness requiredto guarantee the reweldability during its lifetime. The thin blanket shows a superior performance in thesafety related issues and structural viability, but it operates at higher6Li enrichment. It is selected forfurther improvements. The Vacuum Vessel shows to be unviable in both cases, with the thickness varyingbetween 39 and 52 cm. Further chamber modifications, such as the introduction of a neutron reflector,are required to exploit the benefits of the thin blanket with a reasonable Vacuum Vessel.

Direct-Drive Shock-Ignition for the Laser Megajoule.

We present a review of direct-drive shock ignition studies done as alternative for the Laser Mega-Joule to achieve high thermonuclear gain. One-dimensional analysis of HiPER-like Shock-ignited target designs is presented. It is shown that high gain can be achieved with shock ignition for designs which do not ignite only from the laser compression. Shock ignition is achieved for different targets of the fast ignition family which are driven by an absorbed energy between 100 kJ and 850kJ and deliver thermonuclear energies between 10-130 MJ. Shock-Ignition of Direct-Drive Double-Shell non-cryogenic target is also addressed. 2D results concerning the LMJ irradiation geometry are presented. Few systematic analyses are performed for the fuel assembly irradiation uniformity using the whole LMJ configuration or a part of the facility, and for the ignitor spike uniformity. Solutions for fuel assembly and shock ignition on LMJ using 2D calculations are presented. It is shown that high-gain shock-ignition is possible with intensity of each quad less than 1e15 W/cm2but low modes asymmetries displace the ignitor power in the spike towards higher powers.

Systematic Analysis of Direct-Drive Baseline Designs for Shock-Ignition with the Laser Megajoule

Direct-drive inertial confinement thermonuclear fusion consists in illuminating a shell of cryogenic Deuterium and Tritium (DT) mixture with many intense beams of laser light. Capsule is composed of DT gassurrounded by cryogenic DT as combustible fuel. Basic rules are used to define shell geometry from aspect ratio, fuel mass and layers densities. We define baseline designs using two aspect ratio (A=3 and A=5) who complete HiPER baseline design (A=7.7). Aspect ratio is defined as the ratio of ice DT shell inner radius over DT shell thickness. Low aspect ratio improves hydrodynamics stabilities of imploding shell. Laser impulsion shape and ablator thickness are initially defined by using Lindl (1995) pressure ablation and mass ablation formulae for direct-drive using CH layer as ablator. In flight adiabat parameter is close to one during implosion. Velocitie simplosions chosen are between 260 km/s and 365 km/s. More than thousand calculations are realized for each aspect ratio in order to optimize the laser pulse shape. Calculations are performed using the one-dimensional version of the Lagrangian radiation hydrodynamics FCI2. We choose implosion velocities for each initial aspect ratio, and we compute scaled-target family curves for each one to find self-ignition threshold. Then, we pick points on each curves that potentially product high thermonuclear gain and compute shock ignition in the context of Laser MegaJoule. This systematic analyze reveals many working points which complete previous studies ´allowing to highlight baseline designs, according to laser intensity and energy, combustible mass and initial aspect ratio to be relevant for Laser MegaJoule.

Symmetry Issues in Directly Irradiated Targets

In direct drive Inertial Confinement Fusion (ICF), the typical laser beam to laser beam angle is around 30o. This fact makes the study of the irradiation symmetry agenuine 3D problem. In this paper we use the three dimensional version of the MULTI hydrocode to assess the symmetry of such ICF implosions. More specifically, we study a shock-ignition proposal for the Laser-M´egajoule facility (LMJ) in which two of the equatorial beam cones are used to implode and pre compress a spherical capsule (the “reference” capsule of HiPER project) made of 0.59 mg of pure Deuterium-Tritium mixture. The symmetry of this scheme is analysed and optimized to get a design inside the operating limits of LMJ. The studied configuration has been found essentially axial-symmetric, so that the use of 2D hydrocodes would be appropriate for this specific situation.

Definición de un nuevo modelo de negocio sostenible y aplicable a la nueva realidad de negocios y social para la convergencia de operadores de telecomunicación e Internet

La presente tesis analiza la integración del sector de las telecomunicaciones con los de TI y medios que conforman el actual hiper-sector de las TIC, para abordar una propuesta de valor que se plantea a dos niveles. Se expone de un lado, la iniciativa WIMS 2.0, que aborda los aspectos tecnológicos y estratégicos de la convergencia telco e Internet para, posteriormente, definir un nuevo modelo de negocio, que adaptado al nuevo sector integrado y siguiendo paradigmas inéditos como los que plantea la innovación abierta, permita generar nuevos flujos de ingresos en áreas no habituales para los operadores de telecomunicaciones. A lo largo del capítulo 2, el lector encontrará la contextualización del entorno de las comunicaciones de banda ancha desde tres vertientes: los aspectos tecnológicos, los económicos y el mercado actual, todo ello enfocado en una dimensión nacional, europea y mundial. Se establece de esta manera las bases para el desarrollo de los siguientes capítulos al demostrar cómo la penetración de la banda ancha ha potenciado el desarrollo de un nuevo sistema de valor en el sector integrado de las TIC, alrededor del cual surgen propuestas de modelos de negocio originales que se catalogan en una taxonomía propia. En el tercer capítulo se detalla la propuesta de valor de la iniciativa WIMS 2.0, fundada y liderada por el autor de esta tesis. WIMS 2.0, como iniciativa abierta, se dirige a la comunidad como una propuesta de un nuevo ecosistema y como un modelo de referencia integrado sobre el que desplegar servicios convergentes. Adicionalmente, sobre el planteamiento teórico definido se aporta el enfoque práctico que supone el despliegue del modelo de referencia dentro de la arquitectura de un operador como Telefónica. El capítulo 4 muestra el modelo de negocio Innovación 2.0, basado en la innovación abierta con el objetivo de capturar nuevos flujos de ingresos incrementando el portfolio de servicios innovadores gracias a las ideas frescas y brillantes de start-ups. Innovación 2.0 lejos de quedarse en una mera propuesta teórica, muestra sus bondades en el éxito práctico en el mercado que ha validado las hipótesis planteadas. El último capítulo plantea las líneas futuras de investigación tanto en el ámbito de la iniciativa WIMS 2.0 como en el modelo de Innovación 2.0, algunas de las cuales se están comenzando a abordar. 3 Abstract This thesis examines the integration of telecommunications sector with IT and media that make up the current hyper-ICT sector, to address a value proposition that arises at two levels. On one side, WIMS 2.0 initiative, which addresses the technological and strategic aspects of the telco and Internet convergence to later define a new business model, adapted to the new integrated sector and following original paradigms such as those posed by open innovation, which generates new revenue streams in areas not typical for telecom operators. Throughout Chapter 2, the reader will find the contextualization of the broadband communications environment from three aspects: technological, economic and the current market all focused on a national, European and world scale. Thus it establishes the basis for the development of the following chapters by demonstrating how the penetration of broadband has led to the development of a new value system in the integrated sector of the ICT, around which arise proposals of originals business models, which are categorized in a own taxonomy. The third chapter outlines the value proposition of the WIMS 2.0 initiative, founded and led by the author of this thesis. WIMS 2.0, as open initiative, presents to the community a proposal for a new ecosystem and an integrated reference model on which to deploy converged services. Additionally, above the theoretical approach defined, WIMS 2.0 provides the practical approach is provided which is the deployment of the reference model into the architecture of an operator such as Telefónica. Chapter 4 shows the Innovation 2.0 business model, based on open innovation with the goal of capturing new revenue streams by increasing the portfolio of innovative services thanks to the fresh and brilliant ideas from start-ups. Innovation 2.0, far from being a mere theoretical proposition, shows its benefits in the successful deployment in the market, which has validated the hypotheses. The last chapter sets out the future research at both the WIMS 2.0 initiative and Innovation 2.0 model, some of which are beginning to be addressed.

Ultraintense lasers applied to laser fusion material testing: production of ions, X rays and neutrons

Due to the particular characteristics of the fusion products, i.e. very short pulses (less than a few μs long for ions when arriving to the walls; less than 1 ns long for X-rays), very high fluences ( 10 13 particles/cm 2 for both ions and X rays photons) and broad particle energy spectra (up to 10 MeV ions and 100 keV photons), the laser fusion community lacks of facilities to accurately test plasma facing materials under those conditions. In the present work, the ability of ultraintese lasers to create short pulses of energetic particles and high fluences is addressed as a solution to reproduce those ion and X-ray bursts. Based on those parameters, a comparison between fusion ion and laser driven ion beams is presented and discussed, describing a possible experimental set-up to generate with lasers the appropriate ion pulses. At the same time, the possibility of generating X-ray or neutron beams which simulate those of laser fusion environments is also indicated and assessed under current laser intensities. It is concluded that ultraintense lasers should play a relevant role in the validation of materials for laser fusion facilities.

The technofusion project for fusion technology development: opportunities for the inertial community

Technofusion will be the new Spanish singular scientific-technical installation for fusion research. The research activities will be focused on seven areas of materials research considered the most relevant ones for further technological developments of fusion energy. In principle, most of the infrastructure in Technofusion will be useful for both, magnetic (MC) and inertial (IC) confinement fusion communities and most of the research and developments carried out for one of the fusion concepts will be valid and transferable to the other. However, some aspects related to first wall materials strongly differ in MC and IC approaches. This is due to the very different typical ion energy and deposited powers in both cases.

Ab initio Methodology for Calculating Elastic Constant and Sound Velocity for Hydrogen and Deuterium in Molecular Solid Phase

Hydrogen isotopes play a critical role both in inertial and magnetic confinement Nuclear Fusion. Since the preferent fuel needed for this technology is a mixture of deuterium and tritium. The study of these isotopes particularly at very low temperatures carries a technological interest in other applications. The present line promotes a deep study on the structural configuration that hydrogen and deuterium adopt at cryogenic temperatures and at high pressures. Typical conditions occurring in present Inertial Fusion target designs. Our approach is aims to determine the crystal structure characteristics, phase transitions and other parameters strongly correlated to variations of temperature and pressure. With this results is possible calculated the elastic constant and sound velocity for hydrogen and deuterium in molecular solid phase.

Plasma facing materials for fusion reactor applications

The lack of plasma facing materials (PFM) able to withstand the severe magnetiicffusiion radiation conditions expected in fusion reactors is the actual bottle In both fusions approaches energy is released in the form of kinetic energy of neck for fusion to becomes a reality.

Proyectando entre ruinas : lógicas de intervención continua en la arquitectura contemporánea

Los cambios percibidos hacia finales del siglo XX y a principios del nuevo milenio, nos ha mostrado que la crisis cultural de la que somos participes refleja también una crisis de los modelos universales. Nuestra situación contemporánea, parece indicar que ya no es posible formular un sistema estético para atribuirle una vigencia universal e intemporal más allá de su estricta eficacia puntual. La referencia organizada, delimitada, invariable y específica que ofrecía cualquier emplazamiento, en tanto preexistencia, reflejaba una jerarquía del sistema formal basado en lo extensivo: la medida, las normas, el movimiento, el tiempo, la modulación, los códigos y las reglas. Sin embargo, actualmente, algunos aspectos que permanecían latentes sobre lo construido, emergen bajo connotaciones intensivas, transgrediendo la simple manifestación visual y expresiva, para centrase en las propiedades del comportamiento de la materia y la energía como determinantes de un proceso de adaptación en el entorno. A lo largo del todo el siglo XX, el desarrollo de la relación del proyecto sobre lo construido ha sido abordado, casi en exclusiva, entre acciones de preservación o intervención. Ambas perspectivas, manifestaban esfuerzos por articular un pensamiento que diera una consistencia teórica, como soporte para la producción de la acción aditiva. No obstante, en las últimas décadas de finales de siglo, la teoría arquitectónica terminó por incluir pensamientos de otros campos que parecen contaminar la visión sesgada que nos refería lo construido. Todo este entramado conceptual previo, aglomeraba valiosos intentos por dar contenido a una teoría que pudiese ser entendida desde una sola posición argumental. Es así, que en 1979 Ignasi Solá-Morales integró todas las imprecisiones que referían una actuación sobre una arquitectura existente, bajo el termino de “intervención”, el cual fue argumentado en dos sentidos: El primero referido a cualquier tipo de actuación que se puede hacer en un edificio, desde la defensa, preservación, conservación, reutilización, y demás acciones. Se trata de un ámbito donde permanece latente el sentido de intensidad, como factor común de entendimiento de una misma acción. En segundo lugar, más restringido, la idea de intervención se erige como el acto crítico a las ideas anteriores. Ambos representan en definitiva, formas de interpretación de un nuevo discurso. “Una intervención, es tanto como intentar que el edificio vuelva a decir algo o lo diga en una determinada dirección”. A mediados de 1985, motivado por la corriente de revisión historiográfica y la preocupación del deterioro de los centros históricos que recorría toda Europa, Solá-Morales se propone reflexionar sobre “la relación” entre una intervención de nueva arquitectura y la arquitectura previamente existente. Relación condicionada estrictamente bajo consideraciones lingüísticas, a su entender, en sintonía con toda la producción arquitectónica de todo el siglo XX. Del Contraste a la Analogía, resumirá las transformaciones en la concepción discursiva de la intervención arquitectónica, como un fenómeno cambiante en función de los valores culturales, pero a su vez, mostrando una clara tendencia dialógica entres dos categorías formales: El Contraste, enfatizando las posibilidades de la novedad y la diferencia; y por otro lado la emergente Analogía, como una nueva sensibilidad de interpretación del edificio antiguo, donde la semejanza y la diversidad se manifiestan simultáneamente. El aporte reflexivo de los escritos de Solá-Morales podría ser definitivo, si en las últimas décadas antes del fin de siglo, no se hubiesen percibido ciertos cambios sobre la continuidad de la expresión lingüística que fomentaba la arquitectura, hacia una especie de hipertrofia figurativa. Entre muchos argumentos: La disolución de la consistencia compositiva y el estilo unitario, la incorporación volumétrica del proyecto como dispositivo reactivo, y el cambio de visión desde lo retrospectivo hacia lo prospectivo que sugiere la nueva conservación. En este contexto de desintegración, el proyecto, en tanto incorporación o añadido sobre un edificio construido, deja de ser considerado como un apéndice volumétrico subordinado por la reglas compositivas y formales de lo antiguo, para ser considerado como un organismo de orden reactivo, que produce en el soporte existente una alteración en su conformación estructural y sistémica. La extensión, antes espacial, se considera ahora una extensión sensorial y morfológica con la implementación de la tecnología y la hiper-información, pero a su vez, marcados por una fuerte tendencia de optimización energética en su rol operativo, ante el surgimiento del factor ecológico en la producción contemporánea. En una sociedad, como la nuestra, que se está modernizando intensamente, es difícil compartir una adecuada sintonía con las formas del pasado. Desde 1790, fecha de la primera convención francesa para la conservación de monumentos, la escala de lo que se pretende preservar es cada vez más ambiciosa, tanto es así, que al día de hoy el repertorio de lo que se conserva incluye prácticamente todas las tipologías del entorno construido. Para Koolhaas, el intervalo entre el objeto y el momento en el cual se decide su conservación se ha reducido, desde dos milenios en 1882 a unas décadas hoy en día. En breve este lapso desaparecerá, demostrando un cambio radical desde lo retrospectivo hacia lo prospectivo, es decir, que dentro de poco habrá que decidir que es lo que se conserva antes de construir. Solá-Morales, en su momento, distinguió la relación entre lo nuevo y lo antiguo, entre el contraste y la analogía. Hoy casi tres décadas después, el objetivo consiste en evaluar si el modelo de intervención arquitectónica sobre lo construido se ha mantenido desde entonces o si han aparecido nuevas formas de posicionamiento del proyecto sobre lo construido. Nuestro trabajo pretende demostrar el cambio de enfoque proyectual con la preexistencia y que éste tiene estrecha relación con la incorporación de nuevos conceptos, técnicas, herramientas y necesidades que imprimen el contexto cultural, producido por el cambio de siglo. Esta suposición nos orienta a establecer un paralelismo arquitectónico entre los modos de relación en que se manifiesta lo nuevo, entre una posición comúnmente asumida (Tópica), genérica y ortodoxa, fundamentada en lo visual y expresivo de las últimas décadas del siglo XX, y una realidad emergente (Heterotópica), extraordinaria y heterodoxa que estimula lo inmaterial y que parece emerger con creciente intensidad en el siglo XXI. Si a lo largo de todo el siglo XX, el proyecto de intervención arquitectónico, se debatía entre la continuidad y discontinuidad de las categorías formales marcadas por la expresión del edificio preexistente, la nueva intervención contemporánea, como dispositivo reactivo en el paisaje y en el territorio, demanda una absoluta continuidad, ya no visual, expresiva, ni funcional, sino una continuidad fisiológica de adaptación y cambio con la propia dinámica del territorio, bajo nuevas reglas de juego y desplegando planes y estrategias operativas (proyectivas) desde su propia lógica y contingencia. El objeto de esta investigación es determinar los nuevos modos de continuidad y las posibles lógicas de producción que se manifiestan dentro de la Intervención Arquitectónica, intentando superar lo aparente de su relación física y visual, como resultado de la incorporación del factor operativo desplegado por el nuevo dispositivo contemporáneo. Creemos que es acertado mantener la senda connotativa que marca la denominación intervención arquitectónica, por aglutinar conceptos y acercamientos teóricos previos que han ido evolucionando en el tiempo. Si bien el término adolece de mayor alcance operativo desde su formulación, una cualidad que infieren nuestras lógicas contemporáneas, podría ser la reformulación y consolidación de un concepto de intervención más idóneo con nuestros tiempos, anteponiendo un procedimiento lógico desde su propia necesidad y contingencia. Finalmente, nuestro planteamiento inicial aspira a constituir un nueva forma de reflexión que nos permita comprender las complejas implicaciones que infiere la nueva arquitectura sobre la preexistencia, motivada por las incorporación de factores externos al simple juicio formal y expresivo preponderante a finales del siglo XX. Del mismo modo, nuestro camino propuesto, como alternativa, permite proyectar posibles sendas de prospección, al considerar lo preexistente como un ámbito que abarca la totalidad del territorio con dinámicas emergentes de cambio, y con ellas, sus lógicas de intervención.Abstract The perceived changes towards the end of the XXth century and at the beginning of the new milennium have shown us that the cultural crisis in which we participate also reflects a crisis of the universal models. The difference between our contemporary situation and the typical situations of modern orthodoxy and post-modernistic fragmentation, seems to indicate that it is no longer possible to formulate a valid esthetic system, to assign a universal and eternal validity to it beyond its strictly punctual effectiveness; which is even subject to questioning because of the continuous transformations that take place in time and in the sensibility of the subject itself every time it takes over the place. The organised reference that any location offered, limited, invariable and specific, while pre-existing, reflected a hierarchy of the formal system based on the applicable: measure, standards, movement, time, modulation, codes and rules. Authors like Marshall Mc Luhan, Paul Virilio, or Marc Augé anticipated a reality where the conventional system already did not seem to respond to the new architectural requests in which information, speed, disappearance and the virtual had blurred the traditional limits of place; pre-existence did no longer possess a specific delimitation and, on the contrary, they expect to reach a global scale. Currently, some aspects that stayed latent relating to the constructed, surface from intensive connotations, transgressing the simple visual and expressive manifestation in order to focus on the traits of the behaviour of material and energy as determinants of a process of adaptation to the surroundings. Throughout the entire Century, the development of the relation of the project relating to the constructed has been addressed, almost exclusively, in preservational or interventianal actions. Both perspectives showed efforts in order to express a thought that would give a theoretical consistency as a base for the production of the additive action. Nevertheless, the last decades of the Century, architectural theory ended up including thoughts from other fields that seem to contaminate the biased vision 15 which the constructed related us. Ecology, planning, philosophy, global economy, etc, suggest new approaches to the construction of the contemporary city; but this time with a determined idea of change and continuous transformation, that enriches the panorama of thought and architectural practice, at the same time, according to some, it puts disciplinary specification at risk, given that there is no architecture without destruction, the constructed organism requires mutation in order to adjust to the change of shape. All of this previous conceptual framework gathered valuable intents to give importance to a theory that could be understood solely from an argumental position. Thusly, in 1979 Ignasi Solá-Morales integrated all of the imprecisions that referred to an action in existing architecture under the term of “Intervention”, which was explained in two ways: The first referring to any type of intervention that can be carried out in a building, regarding protection, conservation, reuse, etc. It is about a scope where the meaning of intensity stays latent as a common factor of the understanding of a single action. Secondly, more limitedly, the idea of intervention is established as the critical act to the other previous ideas such as restauration, conservation, reuse, etc. Both ultimately represent ways of interpretation of a new speech. “An intervention, is as much as trying to make the building say something again or that it be said in a certain direction”. Mid 1985, motivated by the current of historiographical revision and the concerns regarding the deterioration of historical centres that traversed Europe, Solá-Morales decides to reflect on “the relationship” between an intervention of the new architecture and the previously existing architecture. A relationship determined strictly by linguistic considerations, to his understanding, in harmony with all of the architectural production of the XXth century. From Contrast to Analogy would summarise transformations in the discursive perception of architectural intervention, as a changing phenomenon depending on cultural values, but at the same time, showing a clear dialogical tendency between two formal categories: Contrast, emphasising the possibilities of novelty and difference; and on the other hand the emerging Analogy, as a new awareness of interpretation of the ancient building, where the similarity and diversity are manifested simultaneously. For Solá-Morales the analogical procedure is not based on the visible simultaneity of formal orders, but on associations that the subject establishes throughout time. Through analogy it is tried to overcome the simple visual relationship with the antique, to focus on its spacial, physical and geographical nature. If the analogical attempt guides an opening towards a new continuity; it still persists in the connection of dimensional, typological and figurative factors, subordinate to the formal hierarchy of the preexisting subjects. 16 The reflexive contribution of Solá-Morales’ works could be final, if in the last decades before the end of the century there had not been certain changes regarding linguistic expression, encouraged by architecture, towards a kind of figurative hypertrophy, amongst many arguments we are in this case interested in three moments: The dissolution of the compositional consistency and the united style, the volumetric incorporation of the project as a reactive mechanism, and the change of the vision from retrospective towards prospective that the new conservation suggests. The recurrence to the history of architecture and its recognisable forms, as a way of perpetuating memory and establishing a reference, dissolved any instinct of compositive unity and style, provoking permanent relationships to tend to disappear. The composition and coherence lead to suppose a type of discontinuity of isolated objects in which only possible relationships could appear; no longer as an order of certain formal and compositive rules, but as a special way of setting elements in a specific work. The new globalised field required new forms of consistency between the project and the pre-existent subject, motivated amongst others by the higher pace of market evolution, increase of consumer tax and the level of information and competence between different locations; aspects which finally made stylistic consistence inefficient. In this context of disintegration, the project, in incorporation as well as added to a constructed building, stops being considered as a volumetric appendix subordinate to compositive and formal rules of old, to be considered as an organism of reactive order, that causes a change in the structural and systematic configuration of the existing foundation. The extension, previsouly spatial, is now considered a sensorial and morphological extension, with the implementation of technology and hyper-information, but at the same time, marked by a strong tendency of energetic optimization in its operational role, facing the emergence of the ecological factor in contemporary production. The technological world turns into a new nature, a nature that should be analysed from ecological terms; in other words, as an event of transition in the continuous redistribution of energy. In this area, effectiveness is not only determined by the capacity of adaptation to changing conditions, but also by its transforming capacity “expressly” in order to change an environment. In a society, like ours, that is modernising intensively, it is difficult to share an adecuate agreement with the forms of the past. From 1790, the date of the first French convention for the conservation of monuments, the scale of what is expexted to be preserved is more and more ambitious, so much so that nowadays the repertoire of that what is conserved includes practically all typologies of the constructed surroundings. For Koolhaas, the ínterval between the object and the moment when its conservation is decided has been reduced, from two 17 milennia in 1882 to a few decades nowadays. Shortly this lapse will disappear, showing a radical change of retrospective towards prospective, that is to say, that soon it will be necessary to decide what to conserve before constructing. The shapes of cities are the result of the continuous incorporation of architecture, and perhaps that only through architecture the response to the universe can be understood, the continuity of what has already been constructed. Our work is understood also within that system, modifying the field of action and leaving the road ready for the next movement of those that will follow after us. Continuity does not mean conservatism, continuity means being conscient of the transitory value of our answers to specific needs, accepting the change that we have received. That what has been constructed to remain and last, should cause future interventions to be integrated in it. It is necessary to accept continuity as a rule. Solá-Morales, in his time, distinguished between the relationship with new and old, between contrast and analogy. Today, almost three decades later, the objective consists of evaluating whether the model of architectural intervention in the constructed has been maintained since then or if new ways of positioning the project regarding the constructed have appeared. Our work claims to show the change of the approach of projects with pre-existing subjects and that this has got a close relation to the incorporation of new concepts, techniques, tools and necessities that impress the cultural context, caused by the change of centuries. This assumption guides us to establish a parallelism between the forms of connection where that what is new is manifested between a commonly assumed (topical), generic and orthodox position, based on that what is visual and expressive in the last decades of the XXth century, and an emerging (heterotopical), extraordinary and heterodox reality that stimulates the immaterial and that seems to emerge with growing intensity in the XXIst century. If throughout the XXth century the project of architectural intervention was considered from the continuity and discontinuity of formal categories, marked by the expression of the pre-existing building, the new contemporary intervention, as a reactive device in the landscape and territory, demands an absolute continuity. No longer a visual, expressive or functional one but a morphological continuity of adaptation and change with its own territorial dynamics, under new game rules and unfolding new operative (projective) strategies from its own logic and contingency. 18 The aim of this research is to determine new forms of continuity and the possible logic of production that are expressed in the Architectural Intervention, trying to overcome the obviousness of its physical and visual relationship, at the beginning of this new century, as a result of the incorporation of the operative factor that the new architectural device unfolds. We think it is correct to maintain the connotative path that marks the name architectural intervention by bringing previous concepts and theorical approaches that have been evolving through time together. If the name suffers from a wider operational range because of its formulation, a quality that our contemporary logic provokes, the reformulation and consolidation of an interventional concept could be more suitable for our times, giving preference to a logical method from its own necessity and contingency. It seems that now time shapes the topics, it is no longer about materialising a certain time but about expressing the changes that its new temporality generates. Finally, our initial approach aspires to form a new way of reflection that permits us to understand the complex implications that the new architecture submits the pre-existing subject to, motivated by the incorporation of factors external to simple formal and expressive judgement, prevailing at the end of the XXth century. In the same way, our set road, as an alternative, permits the contemplation of possible research paths, considering that what is pre-existing as an area that spans the whole territory with emerging changing dynamics and, with them, their interventional logics.

The use of the ESS Bilbao installations for laser fusion studies

In this work the use of ESS-Bilbao fast neutron lines for irradiation of materials for nuclear fusion is studied. For the comparison of ESS-Bilbao with an inertial fusion facility a simplified model of HiPER chamber has been used. Several positions for irradiation at ESS-Bilbao have been also compared. The material chosen for the damage analysis is silica due to its importance on IFC optics. In this work a detailed comparison between the two facilities for silica irradiation is given. The comparison covers the neutron fluxes, doses, defect production and PKA spectra. This study is also intended as a methodological approach or guideline for future works on other materials.

Educación y Tecnología 20 columnas sobre el entorno educativo y 4 lecciones sobre el defecto 2000 y otras patologías

Fernando Saéz Vacas escribe sobre tecnología con mirada renacentista, amplia de intereses y saberes. Vivimos en un mundo hiper especializado, donde se cumple la premonición de Machado: "Nadie sabe ya lo que se sabe, pero todo el mundo sabe que de todo hay quien sepa". Necesitamos pensadores que integren tanto saber disperso y fragmentado. Sáez Vacas lo consigue. Devuelve la técnica al mundo de la gran cultura, sin demonizarla y sin divinizarla. Cree que necesitamos conocer su lado brillante y su lado oscuro. Su estudio del efecto 2000 es un ejemplo de perspicacia y ponderación. La infotecnología resuelve problemas y plantea problemas. En este momento nuestras relaciones con la realidad se han hecho altamente ambiguas. La técnica se ha convertido en la gran interfaz. La realidad se desmaterializa progresivamente. El ser humano adquiere una fluidez nueva, que no sabemos bien como evaluar. Sáez Vacas, preocupado por la educación, piensa que el aprendizaje permanente puede crear un sujeto con yoes múltiples. Lo llama con un nombre apabullante: "Mamífero Multimutante Multinootópico", y se pregunta: ¿Cómo podemos educar a un individuo así? La tendencia utilitaria que prevalece en el mundo educativo es mala solución.

Open Technologies for prototyping the Internet of Things

The worldwide "hyper-connection" of any object around us is the challenge that promises to cover the paradigm of the Internet of Things. If the Internet has colonized the daily life of more than 2000 million1 people around the globe, the Internet of Things faces of connecting more than 100000 million2 "things" by 2020. The underlying Internet of Things’ technologies are the cornerstone that promises to solve interrelated global problems such as exponential population growth, energy management in cities, and environmental sustainability in the average and long term. On the one hand, this Project has the goal of knowledge acquisition about prototyping technologies available in the market for the Internet of Things. On the other hand, the Project focuses on the development of a system for devices management within a Wireless Sensor and Actuator Network to offer some services accessible from the Internet. To accomplish the objectives, the Project will begin with a detailed analysis of various “open source” hardware platforms to encourage creative development of applications, and automatically extract information from the environment around them for transmission to external systems. In addition, web platforms that enable mass storage with the philosophy of the Internet of Things will be studied. The project will culminate in the proposal and specification of a service-oriented software architecture for embedded systems that allows communication between devices on the network, and the data transmission to external systems. Furthermore, it abstracts the complexities of hardware to application developers. RESUMEN. La “hiper-conexión” a nivel mundial de cualquier objeto que nos rodea es el desafío al que promete dar cobertura el paradigma de la Internet de las Cosas. Si la Internet ha colonizado el día a día de más de 2000 millones1 de personas en todo el planeta, la Internet de las Cosas plantea el reto de conectar a más de 100000 millones2 de “cosas” para el año 2020. Las tecnologías subyacentes de la Internet de las Cosas son la piedra angular que prometen dar solución a problemas globales interrelacionados como el crecimiento exponencial de la población, la gestión de la energía en las ciudades o la sostenibilidad del medioambiente a largo plazo. Este Proyecto Fin de Carrera tiene como principales objetivos por un lado, la adquisición de conocimientos acerca de las tecnologías para prototipos disponibles en el mercado para la Internet de las Cosas, y por otro lado el desarrollo de un sistema para la gestión de dispositivos de una red inalámbrica de sensores que ofrezcan unos servicios accesibles desde la Internet. Con el fin de abordar los objetivos marcados, el proyecto comenzará con un análisis detallado de varias plataformas hardware de tipo “open source” que estimulen el desarrollo creativo de aplicaciones y que permitan extraer de forma automática información del medio que les rodea para transmitirlo a sistemas externos para su posterior procesamiento. Por otro lado, se estudiarán plataformas web identificadas con la filosofía de la Internet de las Cosas que permitan el almacenamiento masivo de datos que diferentes plataformas hardware transfieren a través de la Internet. El Proyecto culminará con la propuesta y la especificación una arquitectura software orientada a servicios para sistemas empotrados que permita la comunicación entre los dispositivos de la red y la transmisión de datos a sistemas externos, así como facilitar el desarrollo de aplicaciones a los programadores mediante la abstracción de la complejidad del hardware.