Coupled model of initiation and propagation of corrosion in reinforced concrete

Corrosion of reinforcing steel in concrete due to chloride ingress is one of the main causes of the deterioration of reinforced concrete structures. Structures most affected by such a corrosion are marine zone buildings and structures exposed to de-icing salts like highways and bridges. Such process is accompanied by an increase in volume of the corrosión products on the rebarsconcrete interface. Depending on the level of oxidation, iron can expand as much as six times its original volume. This increase in volume exerts tensile stresses in the surrounding concrete which result in cracking and spalling of the concrete cover if the concrete tensile strength is exceeded. The mechanism by which steel embedded in concrete corrodes in presence of chloride is the local breakdown of the passive layer formed in the highly alkaline condition of the concrete. It is assumed that corrosion initiates when a critical chloride content reaches the rebar surface. The mathematical formulation idealized the corrosion sequence as a two-stage process: an initiation stage, during which chloride ions penetrate to the reinforcing steel surface and depassivate it, and a propagation stage, in which active corrosion takes place until cracking of the concrete cover has occurred. The aim of this research is to develop computer tools to evaluate the duration of the service life of reinforced concrete structures, considering both the initiation and propagation periods. Such tools must offer a friendly interface to facilitate its use by the researchers even though their background is not in numerical simulation. For the evaluation of the initiation period different tools have been developed: Program TavProbabilidade: provides means to carry out a probability analysis of a chloride ingress model. Such a tool is necessary due to the lack of data and general uncertainties associated with the phenomenon of the chloride diffusion. It differs from the deterministic approach because it computes not just a chloride profile at a certain age, but a range of chloride profiles for each probability or occurrence. Program TavProbabilidade_Fiabilidade: carries out reliability analyses of the initiation period. It takes into account the critical value of the chloride concentration on the steel that causes breakdown of the passive layer and the beginning of the propagation stage. It differs from the deterministic analysis in that it does not predict if the corrosion is going to begin or not, but to quantifies the probability of corrosion initiation. Program TavDif_1D: was created to do a one dimension deterministic analysis of the chloride diffusion process by the finite element method (FEM) which numerically solves Fick’second Law. Despite of the different FEM solver already developed in one dimension, the decision to create a new code (TavDif_1D) was taken because of the need to have a solver with friendly interface for pre- and post-process according to the need of IETCC. An innovative tool was also developed with a systematic method devised to compare the ability of the different 1D models to predict the actual evolution of chloride ingress based on experimental measurements, and also to quantify the degree of agreement of the models with each others. For the evaluation of the entire service life of the structure: a computer program has been developed using finite elements method to do the coupling of both service life periods: initiation and propagation. The program for 2D (TavDif_2D) allows the complementary use of two external programs in a unique friendly interface: • GMSH - an finite element mesh generator and post-processing viewer • OOFEM – a finite element solver. This program (TavDif_2D) is responsible to decide in each time step when and where to start applying the boundary conditions of fracture mechanics module in function of the amount of chloride concentration and corrosion parameters (Icorr, etc). This program is also responsible to verify the presence and the degree of fracture in each element to send the Information of diffusion coefficient variation with the crack width. • GMSH - an finite element mesh generator and post-processing viewer • OOFEM – a finite element solver. The advantages of the FEM with the interface provided by the tool are: • the flexibility to input the data such as material property and boundary conditions as time dependent function. • the flexibility to predict the chloride concentration profile for different geometries. • the possibility to couple chloride diffusion (initiation stage) with chemical and mechanical behavior (propagation stage). The OOFEM code had to be modified to accept temperature, humidity and the time dependent values for the material properties, which is necessary to adequately describe the environmental variations. A 3-D simulation has been performed to simulate the behavior of the beam on both, action of the external load and the internal load caused by the corrosion products, using elements of imbedded fracture in order to plot the curve of the deflection of the central region of the beam versus the external load to compare with the experimental data.

A three-dimensional self-adaptive hp finite element method for the characterization of waveguide discontinuities

We propose the use of a highly-accurate three-dimensional (3D) fully automatic hp-adaptive finite element method (FEM) for the characterization of rectangular waveguide discontinuities. These discontinuities are either the unavoidable result of mechanical/electrical transitions or deliberately introduced in order to perform certain electrical functions in modern communication systems. The proposed numerical method combines the geometrical flexibility of finite elements with an accuracy that is often superior to that provided by semi-analytical methods. It supports anisotropic refinements on irregular meshes with hanging nodes, and isoparametric elements. It makes use of hexahedral elements compatible with high-order H(curl)H(curl) discretizations. The 3D hp-adaptive FEM is applied for the first time to solve a wide range of 3D waveguide discontinuity problems of microwave communication systems in which exponential convergence of the error is observed.

Simulation of the deformation of polycrystalline nanostructured Ti by computational homogenization

Computational homogenization by means of the finite element analysis of a representative volume element of the microstructure is used to simulate the deformation of nanostructured Ti. The behavior of each grain is taken into account using a single crystal elasto-viscoplastic model which includes the microscopic mechanisms of plastic deformation by slip along basal, prismatic and pyramidal systems. Two different representations of the polycrystal were used. Each grain was modeled with one cubic finite element in the first one while many cubic elements were used to represent each grain in the second one, leading to a model which includes the effect of grain shape and size in a limited number of grains due to the computational cost. Both representations were used to simulate the tensile deformation of nanostructured Ti processed by ECAP-C as well as the drawing process of nanostructured Ti billets. It was found that the first representation based in one finite element per grain led to a stiffer response in tension and was not able to predict the texture evolution during drawing because the strain gradient within each grain could not be captured. On the contrary, the second representation of the polycrystal microstructure with many finite elements per grain was able to predict accurately the deformation of nanostructured Ti.

Métodos numéricos y estadísticos de caracterización de uniones tubulares soldadas para su aplicación en modelos de elementos finitos de estructuras de vehículos

El análisis de estructuras mediante modelos de elementos finitos representa una de las metodologías más utilizadas y aceptadas en la industria moderna. Para el análisis de estructuras tubulares de grandes dimensiones similares a las sobrestructuras de autobuses y autocares, los elementos de tipo viga son comúnmente utilizados y recomendados debido a que permiten obtener resultados satisfactorios con recursos computacionales reducidos. No obstante, los elementos de tipo viga presentan importante desventaja ya que las uniones modeladas presentan un comportamiento infinitamente rígido, esto determina un comportamiento mas rígido en las estructuras modeladas lo que se traduce en fuentes de error para las simulaciones estructurales (hasta un 60%). Mediante el modelado de uniones tubulares utilizando elementos de tipo área o volumen, se pueden obtener modelos más realistas, ya que las características topológicas de la unión propiamente dicha pueden ser reproducidas con un mayor nivel de detalle. Evitándose de esta manera los inconvenientes de los elementos de tipo viga. A pesar de esto, la modelización de estructuras tubulares de grandes dimensiones con elementos de tipo área o volumen representa una alternativa poco atractiva debido a la complejidad del proceso de modelados y al gran número de elementos resultantes lo que implica la necesidad de grandes recursos computacionales. El principal objetivo del trabajo de investigación presentado, fue el de obtener un nuevo tipo de elemento capaz de proporcionar estimaciones más exactas en el comportamiento de las uniones modeladas, al mismo tiempo manteniendo la simplicidad del procesos de modelado propio de los elementos de tipo viga regular. Con el fin de alcanzar los objetivos planteados, fueron realizadas diferentes metodologías e investigaciones. En base a las investigaciones realizadas, se obtuvo un modelo de unión viga alternativa en el cual se introdujeron un total seis elementos elásticos al nivel de la unión mediante los cuales es posible adaptar el comportamiento local de la misma. Adicionalmente, para la estimación de las rigideces correspondientes a los elementos elásticos se desarrollaron dos metodologías, una primera basada en la caracterización del comportamiento estático de uniones simples y una segunda basada en la caracterización del comportamiento dinámico a través de análisis modales. Las mejoras obtenidas mediante la implementación del modelo de unión alternativa fueron analizadas mediante simulaciones y validación experimental en una estructura tubular compleja representativa de sobrestructuras de autobuses y autocares. En base a los análisis comparativos realizados con la uniones simples modeladas y los experimentos de validación, se determinó que las uniones modeladas con elementos de tipo viga son entre un 5-60% más rígidas que uniones equivalentes modeladas con elementos área o volumen. También se determinó que las uniones área y volumen modeladas son entre un 5 a un 10% mas rígidas en comparación a uniones reales fabricadas. En los análisis realizados en la estructura tubular compleja, se obtuvieron mejoras importantes mediante la implementación del modelo de unión alternativa, las estimaciones del modelo viga se mejoraron desde un 49% hasta aproximadamente un 14%. ABSTRACT The analysis of structures with finite elements models represents one of the most utilized an accepted technique in the modern industry. For the analysis of large tubular structures similar to buses and coaches upper structures, beam type elements are utilized and recommended due to the fact that these elements provide satisfactory results at relatively reduced computational performances. However, the beam type elements have a main disadvantage determined by the fact that the modeled joints have an infinite rigid behavior, this shortcoming determines a stiffer behavior of the modeled structures which translates into error sources for the structural simulations (up to 60%). By modeling tubular junctions with shell and volume elements, more realistic models can be obtained, because the topological characteristics of the junction at the joint level can be reproduced more accurately. This way, the shortcoming that the beam type elements present can be solved. Despite this fact, modeling large tubular structures with shell or volume type elements represents an unattractive alternative due to the complexity of the modeling process and the large number of elements that result which imply the necessity of vast computational performances. The main objective of the research presented in this thesis was to develop a new beam type element that would be able to provide more accurate estimations for the local behavior of the modeled junctions at the same time maintaining the simplicity of the modeling process the regular beam type elements have. In order to reach the established objectives of the research activities, a series of different methodologies and investigations have been necessary. From these investigations an alternative beam T-junction model was obtained, in which a total of six elastic elements at the joint level were introduced, the elastic elements allowed us to adapt the local behavior of the modeled junctions. Additionally, for the estimation of the stiffness values corresponding to the elastic elements two methodologies were developed, one based on the T-junction’s static behavior and a second one based on the T-junction’s dynamic behavior by means of modal analysis. The improvements achieved throughout the implementation of this alternative T-junction model were analyzed though mechanical validation in a complex tubular structures that had a representative configuration for buses and coaches upper structures. From the comparative analyses of the finite element modeled T-junctions and mechanical experimental analysis, was determined that the beam type modeled T-junctions have a stiffer behavior compared to equivalent shell and volume modeled T-junctions with average differences ranging from 5-60% based on the profile configurations. It was also determined that the shell and volume models have a stiffer behavior compared to real T-junctions varying from 5 to 10% depending on the profile configurations. Based on the analysis of the complex tubular structure, significant improvements were obtained by the implementation of the alternative beam T-junction model, the model estimations were improved from a 49% to approximately 14%.

Nonlinear models for lateral dynamics of railway vehicles on bridges subject to wind action

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require threedimensional coupled vehicle-bridge models, wheree consideration of wheel to rail contact is a key aspect. Furthermore, an adequate evaluation of safety of rail traffic requires nonlinear models. A nonlinear coupled model is proposed here for vehicle-structure vertical and lateral dynamics. Vehicles are considered as fully three-dimensional multibody systems including gyroscopic terms and large rotation effects. The bridge structure is modeled by means of finite elements which may be of beam, shell or continuum type and may include geometric or material nonlinearities. The track geometry includes distributed track alignment irregularities. Both subsystems (bridge and vehicles) are described with coordinates in absolute reference frames, as opposed to alternative approaches which describe the multibody system with coordinates relative to the base bridge motion. The wheelrail contact employed is a semi-Hertzian model based on realistic wheel-rail profiles. It allows a detailed geometrical description of the contact patch under each wheel including multiple-point contact, flange contact and uplift. Normal and tangential stresses in each contact are integrated at each time-step to obtain the resultant contact forces. The models have been implemented within an existing finite element analysis software with multibody capabilities, Abaqus (Simulia Ltd., 2010). Further details of the model are presented in Antolín et al. (2012). Representative applications are presented for railway vehicles under lateral wind action on laterally compliant viaducts, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Finite element simulation of dispersion in the Bay of Santander

Two mathematical models are used to simulate pollution in the Bay of Santander. The first is the hydrodynamic model that provides the velocity field and height of the water. The second gives the pollutant concentration field as a resultant. Both models are formulated in two-dimensional equations. Linear triangular finite elements are used in the Galerkin procedure for spatial discretization. A finite difference scheme is used for the time integration. At each time step the calculated results of the first model are input to the second model as field data. The efficiency and accuracy of the models are tested by their application to a simple illustrative example. Finally a case study in simulation of pollution evolution in the Bay of Santander is presented

Análisis de elementos viga-columna en régimen no lineal con deformación por cortante

El hormigón estructural sigue siendo sin duda uno de los materiales más utilizados en construcción debido a su resistencia, rigidez y flexibilidad para diseñar estructuras. El cálculo de estructuras de hormigón, utilizando vigas y vigas-columna, es complejo debido a los fenómenos de acoplamiento entre esfuerzos y al comportamiento no lineal del material. Los modelos más empleados para su análisis son el de Bernoulli-Euler y el de Timoshenko, indicándose en la literatura la conveniencia de usar el segundo cuando la relación canto/luz no es pequeña o los elementos están fuertemente armados. El objetivo fundamental de esta tesis es el análisis de elementos viga y viga-columna en régimen no lineal con deformación por cortante, aplicando el concepto de Pieza Lineal Equivalente (PLE). Concepto éste que consiste básicamente en resolver el problema de una pieza en régimen no lineal, transformándolo en uno lineal equivalente, de modo que ambas piezas tengan la misma deformada y los mismos esfuerzos. Para ello, se hizo en primer lugar un estudio comparado de: las distintas propuestas que aplican la deformación por cortante, de los distintos modelos constitutivos y seccionales del hormigón estructural y de los métodos de cálculo no lineal aplicando el método de elementos finitos (MEF). Teniendo en cuenta que la resolución del problema no lineal se basa en la resolución de sucesivos problemas lineales empleando un proceso de homotopía, los problemas lineales de la viga y viga-columna de Timoshenko, se resuelven mediante MEF, utilizando soluciones nodalmente exactas (SNE) y acción repartida equivalente de cualquier orden. Se obtiene así, con muy pocos elementos finitos, una excelente aproximación de la solución, no sólo en los nodos sino en el interior de los elementos. Se introduce el concepto PLE para el análisis de una barra, de material no lineal, sometida a acciones axiales, y se extiende el mismo para el análisis no lineal de vigas y vigas-columna con deformación por cortante. Cabe señalar que para estos últimos, la solución de una pieza en régimen no lineal es igual a la de una en régimen lineal, cuyas rigideces son constantes a trozos, y donde además hay que añadir momentos y cargas puntuales ficticias en los nodos, así como, un momento distribuido ficticio en toda la pieza. Se han desarrollado dos métodos para el análisis: uno para problemas isostáticos y otro general, aplicable tanto a problemas isostáticos como hiperestáticos. El primero determina de entrada la PLE, realizándose a continuación el cálculo por MEF-SNE de dicha pieza, que ahora está en régimen lineal. El general utiliza una homotopía que transforma de manera iterativa, unas leyes constitutivas lineales en las leyes no lineales del material. Cuando se combina con el MEF, la pieza lineal equivalente y la solución del problema original quedan determinadas al final de todo el proceso. Si bien el método general es un procedimiento próximo al de Newton- Raphson, presenta sobre éste la ventaja de permitir visualizar las deformaciones de la pieza en régimen no lineal, de manera tanto cualitativa como cuantitativa, ya que es posible observar en cada paso del proceso la modificación de rigideces (a flexión y cortante) y asimismo la evolución de las acciones ficticias. Por otra parte, los resultados obtenidos comparados con los publicados en la literatura, indican que el concepto PLE ofrece una forma directa y eficiente para analizar con muy buena precisión los problemas asociados a vigas y vigas-columna en las que por su tipología los efectos del cortante no pueden ser despreciados. ABSTRACT The structural concrete clearly remains the most used material in construction due to its strength, rigidity and structural design flexibility. The calculation of concrete structures using beams and beam-column is complex as consequence of the coupling phenomena between stresses and of its nonlinear behaviour. The models most commonly used for analysis are the Bernoulli-Euler and Timoshenko. The second model is strongly recommended when the relationship thickness/span is not small or in case the elements are heavily reinforced. The main objective of this thesis is to analyse the beam and beam-column elements with shear deformation in nonlinear regime, applying the concept of Equivalent Linear Structural Element (ELSE). This concept is basically to solve the problem of a structural element in nonlinear regime, transforming it into an equivalent linear structural element, so that both elements have the same deformations and the same stresses. Firstly, a comparative study of the various proposals of applying shear deformation, of various constitutive and sectional models of structural concrete, and of the nonlinear calculation methods (using finite element methods) was carried out. Considering that the resolution of nonlinear problem is based on solving the successive linear problem, using homotopy process, the linear problem of Timoshenko beam and beam-columns is resolved by FEM, using the exact nodal solutions (ENS) and equivalent distributed load of any order. Thus, the accurate solution approximation can be obtained with very few finite elements for not only nodes, but also for inside of elements. The concept ELSE is introduced to analyse a bar of nonlinear material, subjected to axial forces. The same bar is then used for other nonlinear beam and beam-column analysis with shear deformation. It is noted that, for the last analyses, the solution of a structural element in nonlinear regime is equal to that of linear regime, in which the piecewise-stiffness is constant, the moments and fictitious point loads need to be added at nodes of each element, as well as the fictitious distributed moment on element. Two methods have been developed for analysis: one for isostatic problem and other more general, applicable for both isostatic and hiperstatic problem. The first method determines the ELSE, and then the calculation of this piece is performed by FEM-ENS that now is in linear regime. The general method uses the homotopy that transforms iteratively linear constitutive laws into nonlinear laws of material. When combined with FEM, the ELSE and the solution of the original problem are determined at the end of the whole process. The general method is well known as a procedure closed to Newton-Raphson procedure but presents an advantage that allows displaying deformations of the piece in nonlinear regime, in both qualitative and quantitative way. Since it is possible to observe the modification of stiffness (flexural and shear) in each step of process and also the evolution of the fictitious actions. Moreover, the results compared with those published in the literature indicate that the ELSE concept offers a direct and efficient way to analyze with very good accuracy the problems associated with beams and beams columns in which, by typology, the effects of shear cannot be neglected.

A methodology to calibrate structural finite element models for reinforced concrete structures subject to blast loads

Civil buildings are not specifically designed to support blast loads, but it is important to take into account these potential scenarios because of their catastrophic effects, on persons and structures. A practical way to consider explosions on reinforced concrete structures is necessary. With this objective we propose a methodology to evaluate blast loads on large concrete buildings, using LS-DYNA code for calculation, with Lagrangian finite elements and explicit time integration. The methodology has three steps. First, individual structural elements of the building like columns and slabs are studied, using continuum 3D elements models subjected to blast loads. In these models reinforced concrete is represented with high precision, using advanced material models such as CSCM_CONCRETE model, and segregated rebars constrained within the continuum mesh. Regrettably this approach cannot be used for large structures because of its excessive computational cost. Second, models based on structural elements are developed, using shells and beam elements. In these models concrete is represented using CONCRETE_EC2 model and segregated rebars with offset formulation, being calibrated with continuum elements models from step one to obtain the same structural response: displacement, velocity, acceleration, damage and erosion. Third, models basedon structural elements are used to develop large models of complete buildings. They are used to study the global response of buildings subjected to blast loads and progressive collapse. This article carries out different techniques needed to calibrate properly the models based on structural elements, using shells and beam elements, in order to provide results of sufficient accuracy that can be used with moderate computational cost.

Use of Headed Reinforcement Bars in Contruction. A Theoretical Approach to Determine the Dimensions of Anchorage Plates and Experimental Tests on Knee Joints Subjected to a Closing Moment

In order to reduce costs and time while improving quality, durability and sustainability in structural concrete constructions, a widely used material nowadays, special care must be taken in some crucial phases of the project and execution, including the structure design and calculation, the dosage, dumping and curing of concrete: another important aspect is the proper design and execution of assembly plans and construction details. The framework, a name designating the whole reinforcement bars cage already assembled as shown in the drawings, can be made up of several components and implies higher or lower industrialization degree. The framework costs constitute about one third of the price per cubic meter placed in concrete works. The best solutions from all points of view are clearly those involving an easier processing to achieve the same goal, and consequently carrying a high degree of industrialization, meaning quality and safety in the work. This thesis aims to provide an indepth analysis of a relatively new type of anchoring by plate known as headed reinforcement bars, which can potentially replace standard or L-shaped hooks, improving the cleaning of construction details and enabling a faster, more flexible, and therefore a more economical assembly. A literature review on the topic and an overview of typical applications is provided, followed by some examples of specific applications in real projects. Since a strict theoretical formulation used to provide the design plate dimensions has not yet been put forward, an equation is proposed for the side-face blowout strength of the anchorage, based on the capacity of concrete to carry concentrated loads in cases in which no transverse reinforcement is provided. The correlation of the calculated ultimate load with experimental results available in the literature is given. Besides, the proposed formulation can be expanded to cases in which a certain development length is available: using a software for nonlinear finite element analysis oriented to the study of reinforced concrete, numerical tests on the bond-bearing interaction are performed. The thesis ends with a testing of eight corner joints subjected to a closing moment, held in the Structures Laboratory of the Polytechnic University of Madrid, aiming to check whether the design of such plates as stated is adequate for these elements and whether an element with plate-anchored reinforcement is equivalent to one with a traditional construction detail.

Lateral Dynamic Models for High-Speed Railway Bridges and Vehicles

The analysis of the running safety of railway vehicles on viaducts subject to strong lateral actions such as cross winds requires coupled nonlinear vehicle-bridge interaction models, capable to study extreme events. In this paper original models developed by the authors are described, based on finite elements for the structure, multibody and finite element models for the vehicle, and specially developed interaction elements for the interface between wheel and rail. The models have been implemented within ABAQUS and have full nonlinear capabilities for the structure, the vehicle and the contact interface. An application is developed for the Ulla Viaduct, a 105 m tall arch in the Spanish high-speed railway network. The dynamic analyses allow obtaining critical wind curves, which define the running safety conditions for a given train in terms of speed of circulation and wind speed

Study of the foundations, bearing soil and stability of the minaret-tower of Cordobas Mosque

This research in Cordoba's mosque tower main objective was to analyze and characterize the foundations and the underlying soil, calculating the stability of the monument as well as the settlement and deformations performed, using traditional calculation methods and also by finite elements, and to determine differences between both, as well as the stability factor of the Minaret Tower. The works done to study the soil, were drill bores and dynamic penetration tests, classification of samples by size, Atterberg limits, physical and chemical analysis, showing the typical geotechnical composition of the Guadalquivir valley: an alluvial material composed by sand, gravels and silt clays. To study the foundations, inclined bore samples were extracted with 10-65º, showing calcarenite stone ashlars and lime concrete alternating with stone and brick masonry.

Influencia de la temperatura en la deflexión de firmes flexibles

En esta investigación se ha estudiado el efecto de la variación de la temperatura en la deflexión de firmes flexibles. En primer lugar se han recopilado los criterios existentes de ajuste de la deflexión por efecto de la temperatura. Posteriormente, se ha llevado a cabo un estudio empírico mediante la auscultación de las deflexiones en cinco tramos de carretera con firme flexible y con diferentes espesores de mezclas bituminosas (entre 10 y 30 cm). Las medidas se han efectuado en dos campañas (verano e invierno), tratando de abarcar un amplio rango de temperaturas. En cada campaña, se han llevado a cabo distintas auscultaciones a diferentes temperaturas. Las medidas de cada campaña se han realizado el mismo día. Se han obtenido los coeficientes empíricos de ajuste por temperatura para cada tramo analizado. Además, se ha realizado un estudio teórico mediante la elaboración de diferentes modelos (multicapa elástico lineal, multicapa visco-elástico lineal y elementos finitos) que reproducen la respuesta estructural de los firmes flexibles auscultados. La caracterización mecánica de las mezclas bituminosas se ha realizado mediante ensayos de módulo complejo en laboratorio, a diferentes temperaturas y frecuencias, sobre testigos extraídos en las carreteras estudiadas. Se han calculado los coeficientes teóricos de ajuste por temperatura para cada modelo elaborado y tramo analizado. Finalmente, se ha realizado un estudio comparativo entre los distintos coeficientes de ajuste (existentes, empíricos y teóricos), que ha puesto de manifiesto que, en todos los casos analizados, los coeficientes obtenidos en el modelo de elementos finitos son los que más se aproximan a los coeficientes empíricos (valor de referencia para los tramos analizados). El modelo desarrollado de elementos finitos permite reproducir el comportamiento visco-elástico de las mezclas bituminosas y el carácter dinámico de las cargas aplicadas. Se han utilizado elementos tipo tetraedro isoparamétrico lineal (C3D8R) para el firme y la parte superior del cimiento, mientras que para la parte inferior se han empleado elementos infinitos (CIN3D8). In this research the effect produced by the temperature change on flexible pavements deflection is analysed. First, the existing criteria of deflection adjustment by temperature were collected. Additionally, an empirical analysis was carried out, consisting on deflection tests in five flexible-pavement road sections with different asphalt mix thickness (from 10 to 30 cm). The measures were taken in two seasons (summer and winter) in an effort to register a wide range of temperatures. Different surveys were carried out at different temperatures in each season. The tests of each season were done at the same day. The empirical temperature adjustment factors for every analysed section were obtained. A theoretical study was carried out by developing different models (linear elastic multilayer, linear visco-elastic multilayer and finite elements) that reproduce the structural response of the tested flexible pavements. The mechanical characterization of the asphalt mixes was achieved through laboratory complex-modulus tests at different temperatures and frequencies, using pavement cores from the surveyed roads. The theoretical temperature adjustment factors for each model developed and each section analysed were calculated. Finally, a comparative study among the different adjustment factors (existing, empirical and theoretical) was carried out. It has shown that, in all analysed cases, the factors obtained with the finite elements model are the closest to the empirical factors (reference value for the analysed sections). The finite elements model developed makes it possible to reproduce the visco-elastic behavior of the asphalt mixes and the dynamic nature of the applied loads. Linear isoparametric tetrahedral elements (C3D8R) have been used for the pavement and the subgrade, while infinite elements (CIN3D8) have been used for the foundations.

Modelos de elementos finitos explícitos para explosiones en estructuras reticuladas de hormigón armado : aplicaciones al estudio del colapso de edificios

La frecuencia con la que se producen explosiones sobre edificios, ya sean accidentales o intencionadas, es reducida, pero sus efectos pueden ser catastróficos. Es deseable poder predecir de forma suficientemente precisa las consecuencias de estas acciones dinámicas sobre edificaciones civiles, entre las cuales las estructuras reticuladas de hormigón armado son una tipología habitual. En esta tesis doctoral se exploran distintas opciones prácticas para el modelado y cálculo numérico por ordenador de estructuras de hormigón armado sometidas a explosiones. Se emplean modelos numéricos de elementos finitos con integración explícita en el tiempo, que demuestran su capacidad efectiva para simular los fenómenos físicos y estructurales de dinámica rápida y altamente no lineales que suceden, pudiendo predecir los daños ocasionados tanto por la propia explosión como por el posible colapso progresivo de la estructura. El trabajo se ha llevado a cabo empleando el código comercial de elementos finitos LS-DYNA (Hallquist, 2006), desarrollando en el mismo distintos tipos de modelos de cálculo que se pueden clasificar en dos tipos principales: 1) modelos basados en elementos finitos de continuo, en los que se discretiza directamente el medio continuo mediante grados de libertad nodales de desplazamientos; 2) modelos basados en elementos finitos estructurales, mediante vigas y láminas, que incluyen hipótesis cinemáticas para elementos lineales o superficiales. Estos modelos se desarrollan y discuten a varios niveles distintos: 1) a nivel del comportamiento de los materiales, 2) a nivel de la respuesta de elementos estructurales tales como columnas, vigas o losas, y 3) a nivel de la respuesta de edificios completos o de partes significativas de los mismos. Se desarrollan modelos de elementos finitos de continuo 3D muy detallados que modelizan el hormigón en masa y el acero de armado de forma segregada. El hormigón se representa con un modelo constitutivo del hormigón CSCM (Murray et al., 2007), que tiene un comportamiento inelástico, con diferente respuesta a tracción y compresión, endurecimiento, daño por fisuración y compresión, y rotura. El acero se representa con un modelo constitutivo elastoplástico bilineal con rotura. Se modeliza la geometría precisa del hormigón mediante elementos finitos de continuo 3D y cada una de las barras de armado mediante elementos finitos tipo viga, con su posición exacta dentro de la masa de hormigón. La malla del modelo se construye mediante la superposición de los elementos de continuo de hormigón y los elementos tipo viga de las armaduras segregadas, que son obligadas a seguir la deformación del sólido en cada punto mediante un algoritmo de penalización, simulando así el comportamiento del hormigón armado. En este trabajo se denominarán a estos modelos simplificadamente como modelos de EF de continuo. Con estos modelos de EF de continuo se analiza la respuesta estructural de elementos constructivos (columnas, losas y pórticos) frente a acciones explosivas. Asimismo se han comparado con resultados experimentales, de ensayos sobre vigas y losas con distintas cargas de explosivo, verificándose una coincidencia aceptable y permitiendo una calibración de los parámetros de cálculo. Sin embargo estos modelos tan detallados no son recomendables para analizar edificios completos, ya que el elevado número de elementos finitos que serían necesarios eleva su coste computacional hasta hacerlos inviables para los recursos de cálculo actuales. Adicionalmente, se desarrollan modelos de elementos finitos estructurales (vigas y láminas) que, con un coste computacional reducido, son capaces de reproducir el comportamiento global de la estructura con una precisión similar. Se modelizan igualmente el hormigón en masa y el acero de armado de forma segregada. El hormigón se representa con el modelo constitutivo del hormigón EC2 (Hallquist et al., 2013), que también presenta un comportamiento inelástico, con diferente respuesta a tracción y compresión, endurecimiento, daño por fisuración y compresión, y rotura, y se usa en elementos finitos tipo lámina. El acero se representa de nuevo con un modelo constitutivo elastoplástico bilineal con rotura, usando elementos finitos tipo viga. Se modeliza una geometría equivalente del hormigón y del armado, y se tiene en cuenta la posición relativa del acero dentro de la masa de hormigón. Las mallas de ambos se unen mediante nodos comunes, produciendo una respuesta conjunta. En este trabajo se denominarán a estos modelos simplificadamente como modelos de EF estructurales. Con estos modelos de EF estructurales se simulan los mismos elementos constructivos que con los modelos de EF de continuo, y comparando sus respuestas estructurales frente a explosión se realiza la calibración de los primeros, de forma que se obtiene un comportamiento estructural similar con un coste computacional reducido. Se comprueba que estos mismos modelos, tanto los modelos de EF de continuo como los modelos de EF estructurales, son precisos también para el análisis del fenómeno de colapso progresivo en una estructura, y que se pueden utilizar para el estudio simultáneo de los daños de una explosión y el posterior colapso. Para ello se incluyen formulaciones que permiten considerar las fuerzas debidas al peso propio, sobrecargas y los contactos de unas partes de la estructura sobre otras. Se validan ambos modelos con un ensayo a escala real en el que un módulo con seis columnas y dos plantas colapsa al eliminar una de sus columnas. El coste computacional del modelo de EF de continuo para la simulación de este ensayo es mucho mayor que el del modelo de EF estructurales, lo cual hace inviable su aplicación en edificios completos, mientras que el modelo de EF estructurales presenta una respuesta global suficientemente precisa con un coste asumible. Por último se utilizan los modelos de EF estructurales para analizar explosiones sobre edificios de varias plantas, y se simulan dos escenarios con cargas explosivas para un edificio completo, con un coste computacional moderado. The frequency of explosions on buildings whether they are intended or accidental is small, but they can have catastrophic effects. Being able to predict in a accurate enough manner the consequences of these dynamic actions on civil buildings, among which frame-type reinforced concrete buildings are a frequent typology is desirable. In this doctoral thesis different practical options for the modeling and computer assisted numerical calculation of reinforced concrete structures submitted to explosions are explored. Numerical finite elements models with explicit time-based integration are employed, demonstrating their effective capacity in the simulation of the occurring fast dynamic and highly nonlinear physical and structural phenomena, allowing to predict the damage caused by the explosion itself as well as by the possible progressive collapse of the structure. The work has been carried out with the commercial finite elements code LS-DYNA (Hallquist, 2006), developing several types of calculation model classified in two main types: 1) Models based in continuum finite elements in which the continuous medium is discretized directly by means of nodal displacement degrees of freedom; 2) Models based on structural finite elements, with beams and shells, including kinematic hypothesis for linear and superficial elements. These models are developed and discussed at different levels: 1) material behaviour, 2) response of structural elements such as columns, beams and slabs, and 3) response of complete buildings or significative parts of them. Very detailed 3D continuum finite element models are developed, modeling mass concrete and reinforcement steel in a segregated manner. Concrete is represented with a constitutive concrete model CSCM (Murray et al., 2007), that has an inelastic behaviour, with different tension and compression response, hardening, cracking and compression damage and failure. The steel is represented with an elastic-plastic bilinear model with failure. The actual geometry of the concrete is modeled with 3D continuum finite elements and every and each of the reinforcing bars with beam-type finite elements, with their exact position in the concrete mass. The mesh of the model is generated by the superposition of the concrete continuum elements and the beam-type elements of the segregated reinforcement, which are made to follow the deformation of the solid in each point by means of a penalty algorithm, reproducing the behaviour of reinforced concrete. In this work these models will be called continuum FE models as a simplification. With these continuum FE models the response of construction elements (columns, slabs and frames) under explosive actions are analysed. They have also been compared with experimental results of tests on beams and slabs with various explosive charges, verifying an acceptable coincidence and allowing a calibration of the calculation parameters. These detailed models are however not advised for the analysis of complete buildings, as the high number of finite elements necessary raises its computational cost, making them unreliable for the current calculation resources. In addition to that, structural finite elements (beams and shells) models are developed, which, while having a reduced computational cost, are able to reproduce the global behaviour of the structure with a similar accuracy. Mass concrete and reinforcing steel are also modeled segregated. Concrete is represented with the concrete constitutive model EC2 (Hallquist et al., 2013), which also presents an inelastic behaviour, with a different tension and compression response, hardening, compression and cracking damage and failure, and is used in shell-type finite elements. Steel is represented once again with an elastic-plastic bilineal with failure constitutive model, using beam-type finite elements. An equivalent geometry of the concrete and the steel is modeled, considering the relative position of the steel inside the concrete mass. The meshes of both sets of elements are bound with common nodes, therefore producing a joint response. These models will be called structural FE models as a simplification. With these structural FE models the same construction elements as with the continuum FE models are simulated, and by comparing their response under explosive actions a calibration of the former is carried out, resulting in a similar response with a reduced computational cost. It is verified that both the continuum FE models and the structural FE models are also accurate for the analysis of the phenomenon of progressive collapse of a structure, and that they can be employed for the simultaneous study of an explosion damage and the resulting collapse. Both models are validated with an experimental full-scale test in which a six column, two floors module collapses after the removal of one of its columns. The computational cost of the continuum FE model for the simulation of this test is a lot higher than that of the structural FE model, making it non-viable for its application to full buildings, while the structural FE model presents a global response accurate enough with an admissible cost. Finally, structural FE models are used to analyze explosions on several story buildings, and two scenarios are simulated with explosive charges for a full building, with a moderate computational cost.

Método computacional para la aceleración de análisis paramétricos de modificaciones locales en estructuras complejas sometidas a cargas dinámicas

Dentro del análisis y diseño estructural surgen frecuentemente problemas de ingeniería donde se requiere el análisis dinámico de grandes modelos de elementos finitos que llegan a millones de grados de libertad y emplean volúmenes de datos de gran tamaño. La complejidad y dimensión de los análisis se dispara cuando se requiere realizar análisis paramétricos. Este problema se ha abordado tradicionalmente desde diversas perspectivas: en primer lugar, aumentando la capacidad tanto de cálculo como de memoria de los sistemas informáticos empleados en los análisis. En segundo lugar, se pueden simplificar los análisis paramétricos reduciendo su número o detalle y por último se puede recurrir a métodos complementarios a los elementos .nitos para la reducción de sus variables y la simplificación de su ejecución manteniendo los resultados obtenidos próximos al comportamiento real de la estructura. Se propone el empleo de un método de reducción que encaja en la tercera de las opciones y consiste en un análisis simplificado que proporciona una solución para la respuesta dinámica de una estructura en el subespacio modal complejo empleando un volumen de datos muy reducido. De este modo se pueden realizar análisis paramétricos variando múltiples parámetros, para obtener una solución muy aproximada al objetivo buscado. Se propone no solo la variación de propiedades locales de masa, rigidez y amortiguamiento sino la adición de grados de libertad a la estructura original para el cálculo de la respuesta tanto permanente como transitoria. Adicionalmente, su facilidad de implementación permite un control exhaustivo sobre las variables del problema y la implementación de mejoras como diferentes formas de obtención de los autovalores o la eliminación de las limitaciones de amortiguamiento en la estructura original. El objetivo del método se puede considerar similar a los que se obtienen al aplicar el método de Guyan u otras técnicas de reducción de modelos empleados en dinámica estructural. Sin embargo, aunque el método permite ser empleado en conjunción con otros para obtener las ventajas de ambos, el presente procedimiento no realiza la condensación del sistema de ecuaciones, sino que emplea la información del sistema de ecuaciones completa estudiando tan solo la respuesta en las variables apropiadas de los puntos de interés para el analista. Dicho interés puede surgir de la necesidad de obtener la respuesta de las grandes estructuras en unos puntos determinados o de la necesidad de modificar la estructura en zonas determinadas para cambiar su comportamiento (respuesta en aceleraciones, velocidades o desplazamientos) ante cargas dinámicas. Por lo tanto, el procedimiento está particularmente indicado para la selección del valor óptimo de varios parámetros en grandes estructuras (del orden de cientos de miles de modos) como pueden ser la localización de elementos introducidos, rigideces, masas o valores de amortiguamientos viscosos en estudios previos en los que diversas soluciones son planteadas y optimizadas, y que en el caso de grandes estructuras, pueden conllevar un número de simulaciones extremadamente elevado para alcanzar la solución óptima. Tras plantear las herramientas necesarias y desarrollar el procedimiento, se propone un caso de estudio para su aplicación al modelo de elementos .nitos del UAV MILANO desarrollado por el Instituto Nacional de Técnica Aeroespacial. A dicha estructura se le imponen ciertos requisitos al incorporar un equipo en aceleraciones en punta de ala izquierda y desplazamientos en punta de ala derecha en presencia de la sustentación producida por una ráfaga continua de viento de forma sinusoidal. La modificación propuesta consiste en la adición de un equipo en la punta de ala izquierda, bien mediante un anclaje rígido, bien unido mediante un sistema de reducción de la respuesta dinámica con propiedades de masa, rigidez y amortiguamiento variables. El estudio de los resultados obtenidos permite determinar la optimización de los parámetros del sistema de atenuación por medio de múltiples análisis dinámicos de forma que se cumplan de la mejor forma posible los requisitos impuestos con la modificación. Se comparan los resultados con los obtenidos mediante el uso de un programa comercial de análisis por el método de los elementos .nitos lográndose soluciones muy aproximadas entre el modelo completo y el reducido. La influencia de diversos factores como son el amortiguamiento modal de la estructura original, el número de modos retenidos en la truncatura o la precisión proporcionada por el barrido en frecuencia se analiza en detalle para, por último, señalar la eficiencia en términos de tiempo y volumen de datos de computación que ofrece el método propuesto en comparación con otras aproximaciones. Por lo tanto, puede concluirse que el método propuesto se considera una opción útil y eficiente para el análisis paramétrico de modificaciones locales en grandes estructuras. ABSTRACT When developing structural design and analysis some projects require dynamic analysis of large finite element models with millions of degrees of freedom which use large size data .les. The analysis complexity and size grow if a parametric analysis is required. This problem has been approached traditionally in several ways: one way is increasing the power and the storage capacity of computer systems involved in the analysis. Other obvious way is reducing the total amount of analyses and their details. Finally, complementary methods to finite element analysis can also be employed in order to limit the number of variables and to reduce the execution time keeping the results as close as possible to the actual behaviour of the structure. Following this third option, we propose a model reduction method that is based in a simplified analysis that supplies a solution for the dynamic response of the structure in the complex modal space using few data. Thereby, parametric analysis can be done varying multiple parameters so as to obtain a solution which complies with the desired objetive. We propose not only mass, stiffness and damping variations, but also addition of degrees of freedom to the original structure in order to calculate the transient and steady-state response. Additionally, the simple implementation of the procedure allows an in-depth control of the problem variables. Furthermore, improvements such as different ways to obtain eigenvectors or to remove damping limitations of the original structure are also possible. The purpose of the procedure is similar to that of using the Guyan or similar model order reduction techniques. However, in our method we do not perform a true model order reduction in the traditional sense. Furthermore, additional gains, which we do not explore herein, can be obtained through the combination of this method with traditional model-order reduction procedures. In our procedure we use the information of the whole system of equations is used but only those nodes of interest to the analyst are processed. That interest comes from the need to obtain the response of the structure at specific locations or from the need to modify the structure at some suitable positions in order to change its behaviour (acceleration, velocity or displacement response) under dynamic loads. Therefore, the procedure is particularly suitable for parametric optimization in large structures with >100000 normal modes such as position of new elements, stiffness, mass and viscous dampings in previous studies where different solutions are devised and optimized, and in the case of large structures, can carry an extremely high number of simulations to get the optimum solution. After the introduction of the required tools and the development of the procedure, a study case is proposed with use the finite element model (FEM) of the MILANO UAV developed by Instituto Nacional de Técnica Aeroespacial. Due to an equipment addition, certain acceleration and displacement requirements on left wing tip and right wing tip, respectively, are imposed. The structure is under a continuous sinusoidal wind gust which produces lift. The proposed modification consists of the addition of an equipment in left wing tip clamped through a rigid attachment or through a dynamic response reduction system with variable properties of mass, stiffness and damping. The analysis of the obtained results allows us to determine the optimized parametric by means of multiple dynamic analyses in a way such that the imposed requirements have been accomplished in the best possible way. The results achieved are compared with results from a commercial finite element analysis software, showing a good correlation. Influence of several factors such as the modal damping of the original structure, the number of modes kept in the modal truncation or the precission given by the frequency sweep is analyzed. Finally, the efficiency of the proposed method is addressed in tems of computational time and data size compared with other approaches. From the analyses performed, we can conclude that the proposed method is a useful and efficient option to perform parametric analysis of possible local modifications in large structures.

A subgrid viscosity Lagrance-Galerkin method for convection-diffusion problems

We present and analyze a subgrid viscosity Lagrange-Galerk in method that combines the subgrid eddy viscosity method proposed in W. Layton, A connection between subgrid scale eddy viscosity and mixed methods. Appl. Math. Comp., 133: 14 7-157, 2002, and a conventional Lagrange-Galerkin method in the framework of P1⊕ cubic bubble finite elements. This results in an efficient and easy to implement stabilized method for convection dominated convection diffusion reaction problems. Numerical experiments support the numerical analysis results and show that the new method is more accurate than the conventional Lagrange-Galerkin one.