Oxygen extended sooting index of FAME blends with aviation kerosene

The use of biofuels in the aviation sector has economic and environmental benefits. Among the options for the production of renewable jet fuels, hydroprocessed esters and fatty acids (HEFA) have received predominant attention in comparison with fatty acid methyl esters (FAME), which are not approved as additives for jet fuels. However, the presence of oxygen in methyl esters tends to reduce soot emissions and therefore particulate matter emissions. This sooting tendency is quantified in this work with an oxygen-extended sooting index, based on smoke point measurements. Results have shown considerable reduction in the sooting tendency for all biokerosenes (produced by transesterification and eventually distillation) with respect to fossil kerosenes. Among the tested biokerosenes, that made from palm kernel oil was the most effective one, and nondistilled methyl esters (from camelina and linseed oils) showed lower effectiveness than distilled biokerosenes to reduce the sooting tendency. These results may constitute an additional argument for the use of FAME’s as blend components of jet fuels. Other arguments were pointed out in previous publications, but some controversy has aroused over the use of these components. Some of the criticism was based on the fact that the methods used in our previous work are not approved for jet fuels in the standard methods and concluded that the use of FAME in any amount is, thus, inappropriate. However, some of the standard methods are not updated for considering oxygenated components (like the method for obtaining the lower heating value), and others are not precise enough (like the methods for measuring the freezing point), whereas some alternative methods may provide better reproducibility for oxygenated fuels.

A Dynamically Adaptable Bus Architecture for Trading-Off Among Performance, Consumption and Dependability in Cyber-Physical Systems

Cyber-Physical Systems need to handle increasingly complex tasks, which additionally, may have variable operating conditions over time. Therefore, dynamic resource management to adapt the system to different needs is required. In this paper, a new bus-based architecture, called ARTICo3, which by means of Dynamic Partial Reconfiguration, allows the replication of hardware tasks to support module redundancy, multi-thread operation or dual-rail solutions for enhanced side-channel attack protection is presented. A configuration-aware data transaction unit permits data dispatching to more than one module in parallel, or provide coalesced data dispatching among different units to maximize the advantages of burst transactions. The selection of a given configuration is application independent but context-aware, which may be achieved by the combination of a multi-thread model similar to the CUDA kernel model specification, combined with a dynamic thread/task/kernel scheduler. A multi-kernel application for face recognition is used as an application example to show one scenario of the ARTICo3 architecture.

A Dynamically Adaptable Image Processing Application Trading Off Between High Performance, Consumption and Dependability in Real Time

As embedded systems evolve, problems inherent to technology become important limitations. In less than ten years, chips will exceed the maximum allowed power consumption affecting performance, since, even though the resources available per chip are increasing, frequency of operation has stalled. Besides, as the level of integration is increased, it is difficult to keep defect density under control, so new fault tolerant techniques are required. In this demo work, a new dynamically adaptable virtual architecture (ARTICo3) to allow dynamic and context-aware use of resources is implemented in a high performance Wireless Sensor node (HiReCookie) to perform an image processing application.

Evaluación de la seguridad al deslizamiento de una presa de fábrica en un cimiento con una familia de discontinuidades y con un criterio de rotura con ley de fluencia no asociada

En España existen del orden de 1,300 grandes presas, de las cuales un 20% fueron construidas antes de los años 60. El hecho de que existan actualmente una gran cantidad de presas antiguas aún en operación, ha producido un creciente interés en reevaluar su seguridad empleando herramientas nuevas o modificadas que incorporan modelos de fallo teóricos más completos, conceptos geotécnicos más complejos y nuevas técnicas de evaluación de la seguridad. Una manera muy común de abordar el análisis de estabilidad de presas de gravedad es, por ejemplo, considerar el deslizamiento a través de la interfase presa-cimiento empleando el criterio de rotura lineal de Mohr-Coulomb, en donde la cohesión y el ángulo de rozamiento son los parámetros que definen la resistencia al corte de la superficie de contacto. Sin embargo la influencia de aspectos como la presencia de planos de debilidad en el macizo rocoso de cimentación; la influencia de otros criterios de rotura para la junta y para el macizo rocoso (ej. el criterio de rotura de Hoek-Brown); las deformaciones volumétricas que ocurren durante la deformación plástica en el fallo del macizo rocoso (i.e., influencia de la dilatancia) no son usualmente consideradas durante el diseño original de la presa. En este contexto, en la presente tesis doctoral se propone una metodología analítica para el análisis de la estabilidad al deslizamiento de presas de hormigón, considerando un mecanismo de fallo en la cimentación caracterizado por la presencia de una familia de discontinuidades. En particular, se considera la posibilidad de que exista una junta sub-horizontal, preexistente y persistente en el macizo rocoso de la cimentación, con una superficie potencial de fallo que se extiende a través del macizo rocoso. El coeficiente de seguridad es entonces estimado usando una combinación de las resistencias a lo largo de los planos de rotura, cuyas resistencias son evaluadas empleando los criterios de rotura no lineales de Barton y Choubey (1977) y Barton y Bandis (1990), a lo largo del plano de deslizamiento de la junta; y el criterio de rotura de Hoek y Brown (1980) en su versión generalizada (Hoek et al. 2002), a lo largo del macizo rocoso. La metodología propuesta también considera la influencia del comportamiento del macizo rocoso cuando este sigue una ley de flujo no asociada con ángulo de dilatancia constante (Hoek y Brown 1997). La nueva metodología analítica propuesta es usada para evaluar las condiciones de estabilidad empleando dos modelos: un modelo determinista y un modelo probabilista, cuyos resultados son el valor del coeficiente de seguridad y la probabilidad de fallo al deslizamiento, respectivamente. El modelo determinista, implementado en MATLAB, es validado usando soluciones numéricas calculadas mediante el método de las diferencias finitas, empleando el código FLAC 6.0. El modelo propuesto proporciona resultados que son bastante similares a aquellos calculados con FLAC; sin embargo, los costos computacionales de la formulación propuesta son significativamente menores, facilitando el análisis de sensibilidad de la influencia de los diferentes parámetros de entrada sobre la seguridad de la presa, de cuyos resultados se obtienen los parámetros que más peso tienen en la estabilidad al deslizamiento de la estructura, manifestándose además la influencia de la ley de flujo en la rotura del macizo rocoso. La probabilidad de fallo es obtenida empleando el método de fiabilidad de primer orden (First Order Reliability Method; FORM), y los resultados de FORM son posteriormente validados mediante simulaciones de Monte Carlo. Los resultados obtenidos mediante ambas metodologías demuestran que, para el caso no asociado, los valores de probabilidad de fallo se ajustan de manera satisfactoria a los obtenidos mediante las simulaciones de Monte Carlo. Los resultados del caso asociado no son tan buenos, ya que producen resultados con errores del 0.7% al 66%, en los que no obstante se obtiene una buena concordancia cuando los casos se encuentran en, o cerca de, la situación de equilibrio límite. La eficiencia computacional es la principal ventaja que ofrece el método FORM para el análisis de la estabilidad de presas de hormigón, a diferencia de las simulaciones de Monte Carlo (que requiere de al menos 4 horas por cada ejecución) FORM requiere tan solo de 1 a 3 minutos en cada ejecución. There are 1,300 large dams in Spain, 20% of which were built before 1960. The fact that there are still many old dams in operation has produced an interest of reevaluate their safety using new or updated tools that incorporate state-of-the-art failure modes, geotechnical concepts and new safety assessment techniques. For instance, for gravity dams one common design approach considers the sliding through the dam-foundation interface, using a simple linear Mohr-Coulomb failure criterion with constant friction angle and cohesion parameters. But the influence of aspects such as the persistence of joint sets in the rock mass below the dam foundation; of the influence of others failure criteria proposed for rock joint and rock masses (e.g. the Hoek-Brown criterion); or the volumetric strains that occur during plastic failure of rock masses (i.e., the influence of dilatancy) are often no considered during the original dam design. In this context, an analytical methodology is proposed herein to assess the sliding stability of concrete dams, considering an extended failure mechanism in its rock foundation, which is characterized by the presence of an inclined, and impersistent joint set. In particular, the possibility of a preexisting sub-horizontal and impersistent joint set is considered, with a potential failure surface that could extend through the rock mass; the safety factor is therefore computed using a combination of strength along the rock joint (using the nonlinear Barton and Choubey (1977) and Barton and Bandis (1990) failure criteria) and along the rock mass (using the nonlinear failure criterion of Hoek and Brown (1980) in its generalized expression from Hoek et al. (2002)). The proposed methodology also considers the influence of a non-associative flow rule that has been incorporated using a (constant) dilation angle (Hoek and Brown 1997). The newly proposed analytical methodology is used to assess the dam stability conditions, employing for this purpose the deterministic and probabilistic models, resulting in the sliding safety factor and the probability of failure respectively. The deterministic model, implemented in MATLAB, is validated using numerical solution computed with the finite difference code FLAC 6.0. The proposed deterministic model provides results that are very similar to those computed with FLAC; however, since the new formulation can be implemented in a spreadsheet, the computational cost of the proposed model is significantly smaller, hence allowing to more easily conduct parametric analyses of the influence of the different input parameters on the dam’s safety. Once the model is validated, parametric analyses are conducting using the main parameters that describe the dam’s foundation. From this study, the impact of the more influential parameters on the sliding stability analysis is obtained and the error of considering the flow rule is assessed. The probability of failure is obtained employing the First Order Reliability Method (FORM). The probabilistic model is then validated using the Monte Carlo simulation method. Results obtained using both methodologies show good agreement for cases in which the rock mass has a nonassociate flow rule. For cases with an associated flow rule errors between 0.70% and 66% are obtained, so that the better adjustments are obtained for cases with, or close to, limit equilibrium conditions. The main advantage of FORM on sliding stability analyses of gravity dams is its computational efficiency, so that Monte Carlo simulations require at least 4 hours on each execution, whereas FORM requires only 1 to 3 minutes on each execution.

Extended phone log-likelihood ratio features and acoustic-based I-vectors for language recognition

This paper presents new techniques with relevant improvements added to the primary system presented by our group to the Albayzin 2012 LRE competition, where the use of any additional corpora for training or optimizing the models was forbidden. In this work, we present the incorporation of an additional phonotactic subsystem based on the use of phone log-likelihood ratio features (PLLR) extracted from different phonotactic recognizers that contributes to improve the accuracy of the system in a 21.4% in terms of Cavg (we also present results for the official metric during the evaluation, Fact). We will present how using these features at the phone state level provides significant improvements, when used together with dimensionality reduction techniques, especially PCA. We have also experimented with applying alternative SDC-like configurations on these PLLR features with additional improvements. Also, we will describe some modifications to the MFCC-based acoustic i-vector system which have also contributed to additional improvements. The final fused system outperformed the baseline in 27.4% in Cavg.

The extended Betz–Lanchester limit

A proposal for an extended formulation of the power coefficient of a wind turbine is presented. This new formulation is a generalization of the Betz–Lanchester expression for the power coefficient as function of the axial deceleration of the wind speed provoked by the wind turbine in operation. The extended power coefficient takes into account the benefits of the power produced and the cost associated to the production of this energy. By the simple model proposed is evidenced that the purely energetic optimum operation condition giving rise to the Betz–Lanchester limit (maximum energy produced) does not coincide with the global optimum operational condition (maximum benefit generated) if cost of energy and degradation of the wind turbine during operation is considered. The new extended power coefficient is a general parameter useful to define global optimum operation conditions for wind turbines, considering not only the energy production but also the maintenance cost and the economic cost associated to the life reduction of the machine.

Compatibilidad de Eretmocerus mundus Mercet (Hymenoptera: Aphelinidae) y Amblyseius swirskii Athias-Henriot (Acari: Phytoseiidae), importantes enemigos naturales de la mosca blanca Bemisia tabaci (Gennadius) (Hemiptera: Aleyrodidae) en cultivos hortícolas, con nuevas barreras físicas selectivas y modernos plaguicidas

Los programas de Gestión Integrada de Plagas (GIP) promueven el uso de estrategias de control que sean respetuosas con el medio ambiente, sin embargo el uso de insecticidas en los cultivos hortícolas sigue siendo necesario para el control de determinadas plagas, como es el caso de la mosca blanca Bemisia tabaci (Gennadius). Por ello, el objetivo de esta tesis es el estudio de la integración de las tres estrategias de control más empleadas hoy en día para el control de plagas: el control biológico, el físico y el químico. Una primera parte de este trabajo ha consistido en el estudio de los efectos letales y subletales de once insecticidas, aplicados a la dosis máxima de campo, sobre los enemigos naturales Eretmocerus mundus Mercet y Amblyseius swirskii Athias-Henriot, mediante ensayos de laboratorio y persistencia (laboratorio extendido). Para la evaluación de la toxicidad de los insecticidas sobre los estados de vida más protegidos de estos enemigos naturales, se trataron bajo la Torre de Potter las pupas de E. mundus y los huevos de A. swirskii. Además, se llevaron a cabo ensayos de contacto residual para determinar los efectos letales y subletales de estos insecticidas sobre el estado adulto de ambas especies de enemigos naturales. Para ello, los pesticidas se aplicaron sobre placas de cristal (laboratorio) o sobre plantas (laboratorio extendido: persistencia). Los resultados mostraron que los insecticidas flonicamida, flubendiamida, metaflumizona, metoxifenocida, spiromesifen y spirotetramat eran compatibles con el estado de pupa de E. mundus (OILB 1: Inocuos). Sin embargo, abamectina, deltametrina y emamectina fueron categorizadas como ligeramente tóxicas (OILB 2) al causar efectos deletéreos. Los dos pesticidas más tóxicos fueron spinosad y sulfoxaflor, los cuales redujeron significativamente la emergencia de las pupas tratadas (OILB 4: Tóxicos). Flonicamida, flubendiamida, metoxifenocida y spiromesifen fueron compatibles con el estado adulto de E. mundus (OILB 1: Inocuos). Abamectina, deltametrina, emamectina, metaflumizona y spiromesifen pueden ser recomendados para su uso en programas de GIP, si se usan los plazos de seguridad apropiados, de acuerdo con la persistencia de cada uno de estos insecticidas, antes de la liberación del enemigo natural. Al contrario, spinosad y sulfoxaflor no resultaron ser compatibles (OILB D: Persistentes), aunque la realización de ensayos adicionales es necesaria para ver los efectos de los mismos en campo. Todos los insecticidas estudiados, excepto el spirotetramat (OILB 2: Ligeramente tóxico), fueron selectivos para el estado de huevo de A. swirskii (OILB 1: Inocuos). Flonicamida, flubendiamida, metaflumizona, metoxifenocida, spiromesifen, spirotetramat y sulfoxaflor, fueron compatibles con el estado adulto de A. swirskii (OILB 1: Inocuos). Abamectina, deltametrina, emamectina y spinosad pueden ser recomendados para su uso en programas de GIP, si se usan los plazos de seguridad apropiados, de acuerdo con la persistencia de cada uno de estos insecticidas, antes de la liberación del enemigo natural. Entre las nuevas estrategias de la GIP, los plásticos y mallas fotoselectivas han demostrado ser una herramienta importante para el control de plagas y enfermedades en cultivos hortícolas protegidos. Por ello, en una segunda parte de este trabajo, se estudiaron tanto los efectos directos, como la combinación de efectos directos y mediados por planta y plaga de ambientes pobres en luz UV, en presencia o ausencia del Virus del rizado amarillo del tomate (TYLCV), sobre E. mundus. En primer lugar, se realizó un ensayo al aire libre para la evaluación de la capacidad de vuelo de E. mundus en cajas tipo túnel (1 x 0,6 x 0,6 m) cubiertas con distintas barreras absorbentes de luz UV. Se detectó un efecto directo en la capacidad de orientación de E. mundus, debido a que este parasitoide utiliza estímulos visuales para localizar a sus huéspedes, únicamente en las barreras que bloqueaban más del 65% de la luz UV (malla G). En segundo lugar, bajo condiciones de invernadero, se evaluó la combinación de efectos directos y mediados por planta y plaga sobre E. mundus, usando plantas de tomate sanas o infectadas con el TYLCV y cajas (30 x 30 x 60 cm) cubiertas con los distintos plásticos fotoselectivos. En este caso, no se observó ningún efecto en la capacidad benéfica del parasitoide cuando este estaba en contacto con plantas de tomate infestadas con ninfas de B. tabaci, lo que demuestra que este insecto usa estímulos táctiles para encontrar a sus huéspedes a cortas distancias. Además, las diferentes condiciones de radiación UV estudiadas tuvieron cierto impacto en la morfología, fisiología y bioquímica de las plantas de tomate, infestadas o no con el virus de la cuchara, detectándose pequeñas alteraciones en alguno de los parámetros estudiados, como el peso fresco y seco, el contenido en H y el espesor de las cutículas y de las paredes celulares de la epidermis foliar. Por último, no se observaron efectos de la radiación UV mediados por planta, ni en B. tabaci ni en su parasitoide, E. mundus. En una tercera parte, se evaluaron los efectos de una malla tratada con bifentrin sobre ambos enemigos naturales, en ensayos de laboratorio, semicampo y campo. Las mallas tratadas fueron diseñadas originariamente para el control de mosquitos vectores de la malaria, y actualmente se está trabajando para su uso en agricultura, como una nueva estrategia de control de plagas. En ensayos de laboratorio, cuando adultos de E. mundus y A. swirskii se expusieron por contacto durante 72 horas con la malla tratada (cajas de 6 cm diámetro), se registró una alta mortalidad. Sin embargo, en el ensayo de preferencia, estos enemigos naturales no fueron capaces de detectar la presencia de bifentrin y, en aquellos individuos forzados a atravesar la malla tratada, no se observó mortalidad a corto plazo (72 horas). En estudios de semicampo, llevados a cabo bajo condiciones de invernadero en cajas de 25 x 25 x 60 cm de altura, la capacidad benéfica de E. mundus no se vio afectada. Finalmente, en ensayos de campo llevados a cabo en invernaderos comerciales (4000m2) en Almería, A. swirskii no se vio afectado por la presencia en el cultivo de la malla tratada con bifentrin y los niveles de infestación de B. tabaci y F. occidentalis detectados bajo dicha malla, fueron inferiores a los del control. Por último, se ha evaluado la composición de la microflora bacteriana de tres especies de parasitoides, E. mundus, Eretmocerus eremicus Rose & Zolnerowich y Encarsia formosa Gahan, y la influencia de la misma en su susceptibilidad a insecticidas. Se llevó a cabo una extracción total de ADN de los insectos y la región variable V4 del ARNr se amplificó usando cebadores universales bacterianos. Para identificar las secuencias de los géneros bacterianos presentes en los parasitoides, se realizó una Next Generation sequencing (Illumina sequencing). Una vez identificados los géneros bacterianos, el gen ADNr 16S de las Actinobacterias se amplificó del ADN extraído de los insectos, usando cebadores universales bacterianos y específicos de Actinobacterias, y los productos de la Nested PCR fueron clonados para identificar todas las especies del género Arthrobacter. Tres bacterias (A. aurescens Phillips, A. nicotinovarans Kodama, Yamamoto, Amano and Amichi y A. uratoxydans Stackebrandt, Fowler, Fiedler and Seiler), próximas a las especies de Arthrobacter presentes en los parasitoides, se obtuvieron de la colección bacteriana del BCCMTM/LMG y se midió su actividad esterasa. Finalmente, se realizaron ensayos con antibióticos (tetraciclina) y de contacto residual con insecticidas (abamectina) para determinar la influencia de las especies de Arthrobacter en la susceptibilidad de E. mundus a insecticidas. Los resultados muestran que este género bacteriano puede afectar a la toxicidad de E. mundus a abamectina, mostrando la importancia de la comunidad microbiana en enemigos naturales, factor que debe ser considerado en los estudios de evaluación de los riesgos de los insecticidas. ABSTRACT Integrated Pest Management (IPM) programs promote the use of control strategies more respectful with the environment; however the use of insecticides in vegetable crops is still needed to control certain pests, such as the whitefly Bemisia tabaci (Gennadius). Therefore, the objective of this work is to study the integration of the three most commonly used pest control strategies nowadays: biological, physical and chemical control. Firstly, the lethal and sublethal effects of eleven insecticides, applied at their maximum field recommended concentration, on the parasitic wasp Eretmocerus mundus Mercet and the predator Amblyseius swirskii Athias-Henriot has been assessed in the laboratory and in persistence tests (extended laboratory). To test the effects of pesticides on the most protected life stage of these natural enemies, E. mundus pupae and A. swirskii eggs were sprayed under a Potter precision spray tower. Laboratory contact tests were therefore conducted to determine the lethal and sublethal effects of these pesticides on the adult stage of these natural enemies. In the residual contact tests the pesticides were applied on glass plates (laboratory) or plants (extended laboratory: persistence). The study showed that the insecticides flonicamid, flubendiamide, metaflumizone, methoxyfenozide, spiromesifen and spirotetramat were selective for E. mundus pupae (IOBC 1: Harmless). Nevertheless, abamectin, deltamethrin and emamectin were categorized as slightly harmful (IOBC 2) due to the deleterious effects caused. The two most harmful pesticides were spinosad and sulfoxaflor, which significantly reduced the adult emergence from treated pupae (IOBC 4: Harmful). Flonicamid, flubendiamide, methoxyfenozide and spiromesifen were compatible with E. mundus adults (IOBC 1: Harmless). Base on the duration of the harmful activity, abamectin, deltamethrin, emamectin, metaflumizone and spirotetramat could be recommended for use in IPM programs if appropriate safety deadlines are used before the natural enemy release. On the contrary, spinosad and sulfoxaflor were not compatible (IOBC D: persistent), although additional studies are required to determine their effects under field conditions. All the pesticides tested, except spirotetramat (IOBC 2: Slightly harmful), were selective for A. swirskii eggs (IOBC 1: Harmless). Flonicamid, flubendiamide, metaflumizone, methoxyfenozide, spiromesifen, spirotetramat and sulfoxaflor were compatible with A. swirskii adults (IOBC 1: Harmless). However, abamectin, deltamethrin, emamectin and spinosad could be recommended for use in IPM programs if appropriate safety deadlines are used before the natural enemy release. Among new IPM strategies, UV-absorbing photoselective plastic films and nets have been shown to be an important tool for the control of pests and diseases in horticultural protected crops. Because of that, we secondly studied the plant and pest insect-mediated and/or the direct effects on E. mundus under different UV radiation conditions, in presence or absence of the Tomato Yellow Leaf Curl Virus (TYLCV). In the first experiment, performed outdoors, the flight activity of E. mundus was studied in one-chamber tunnels (1 x 0.6 x 0.6 m) covered with different photoselective barriers. Because E. mundus uses visual cues for host location at a long distance, a direct effect on its host location ability was detected, but only in the UV-absorbing barriers blocking more than 65% of the UV light (G net). In a second experiment, the direct and plant and pest insect-mediated effects of different UV radiation conditions on E. mundus were studied, inside cages (30 x 30 x 60 cm) covered with the different UVplastic films and under greenhouse conditions, using healthy or TYLCV-virus infected tomato plants. In this case, not any effect on the beneficial capacity of this parasitoid was detected, proving that he uses tactile cues at a short distance of the host. Moreover, the different UV radiation conditions studied had a certain direct impact in the morphology, physiology and biochemistry of tomato plants infested or not with the TYLCV, and small alterations in some parameters such as fresh and dry weight, H percentage and cuticle and cell wall thickness of epidermal cells of the leaves, were detected. Finally, none plant-mediated UV effects neither in the whitefly B. tabaci nor in their parasitic wasp were found. Thirdly, the effects of a bifenthrin treated net were evaluated in different laboratory, semi-field and field experiments on the natural enemies studied. Treated nets were developed long time ago aiming at the control of the mosquitoes vectors of malaria, and nowadays, there is a great interest on assessing the possibility of their use in agriculture. In laboratory assays, a high mortality was recorded when E. mundus and A. swirskii adults were exposed by contact to the bifenthrin treated net for 72 hours in small cages (12 cm diameter). However, these natural enemies were not able to detect the presence of bifenthrin in a dual-choice test and no short-term mortality (72 hours) was recorded in those individuals that went through the treated net. In semi-field assays, performed under greenhouse conditions with cages of 25 x 25 x 60 cm high, the beneficial capacity of E. mundus was not affected. Finally, in field assays carried out in commercial multispan greenhouses (4000 m2) in Almería, A. swirskii was not affected by the presence of the bifenthrin treated net in the crop and the B. tabaci and F. occidentalis infestation levels were significantly lower than in the control. Finally, the composition of the microflora present in three species of parasitoids, E. mundus, Eretmocerus eremicus Rose & Zolnerowich and Encarsia formosa Gahan, and its influence in their susceptibility to insecticides, have been assessed. A total DNA extraction was performed on insects and universal bacterial primers were used to amplify the variable V4 region of the rRNA. A Next Generation sequencing (Illumina sequencing) was performed to identify the sequences of the bacterial genera present in the parasitic wasps. Once, the bacterial genera were identified, 16S rDNA gene of Actinobacteria were amplified from insects DNA extracts using the universal bacterial and actinobacterial primers, and the nested PCR products, were cloned to identify the Arthrobacter species. Three bacteria (A. aurescens Phillips, A. nicotinovarans Kodama, Yamamoto, Amano and Amichi and A. uratoxydans Stackebrandt, Fowler, Fiedler and Seiler), having the closest match with the Arthrobacter species present in the parasitic wasps, were obtained from the BCCMTM/LMG bacteria collection and its esterase activity was measured. Finally, antibiotic and residual contact tests were done to determine the influence of Arthrobacter species in the susceptibility of E. mundus to pesticides (abamectin). The results suggest that this bacterial genus can affect the toxicity of E. mundus to abamectin, which in turn supports the importance of the microbial community in natural enemies that it should be considered as a factor in risk assessment tests of pesticides.