Co2 capture in power plants-using the oxy-combustion principle

In the C02 capture from power generation, the energy penalties for the capture are one of the main challenges. Nowadays, the post-combustion methods have energy penalties 10wer than the oxy combustion and pre-combustion technologies. One of the main disadvantages of the post combustion method is the fact that the capture ofC02at atmospheric pressure requires quite big equipment for the high flow rates of flue gas, and the 10w partial pressure of the CO2generates an important 10ss of energy. The A1lam cyc1e presented for NETPOWER gives high efficiencies in the power production and 10w energy penalties. A simulation of this cyc1e is made together with a simulation of power plants with pre-combustion and post-combustion capture and without capture for natural gas and forcoa1. The simulations give 10wer efficiencies than the proposed for NETPOWER For natural gas the efficiency is 52% instead of the 59% presented, and 33% instead of51% in the case of using coal as fuel. Are brought to light problems in the CO2compressor due the high flow ofC02that is compressed unti1300 bar to be recyc1ed into the combustor.

An extended electron beam for auroral studies

An electrically floating metallic bare tether in a low Earth orbit would be highly negative with respect to the ambient plasma over most of its length, and would be bombarded by ambient ions. This would liberate secondary electrons, which, after acceleration through the same voltage, would form a magnetically guided two-sided planar e-beam. Upon impact on the atmospheric E-layer, at about 120-140 Km altitude auroral effects (ionization and light emission) can be expected. This paper examines in a preliminary way the feasibility of using this effect as an upper atmospheric probe. It is concluded that significant perturbations can be produced along the illuminated planar sheet of the atmosphere, with ionization rates of several thousand cm-3 sec1. Observation of the induced optical emission is made difficult by the narrowness and high moving speed of the illuminated zone, but it is shown that vertical resolution of single spectral lines is possible, as is wider spectral coverage with no vertical resolution.

Interband absorption of photons by extended states in intermediate band solar cells

This paper considers sub-bandgap photon absorption in an InAs/GaAs quantum dot matrix. Absorption coefficients are calculated for transitions from the extended states in the valence band to confined states in the conduction band. This completes a previous body of work in which transitions between bound states were calculated. The calculations are based on the empirical k·p Hamiltonian considering the quantum dots as parallelepipeds. The extended states may be only partially extended?in one or two dimensions?or extended in all three dimensions. It is found that extended-to-bound transitions are, in general, weaker than bound-to-bound transitions, and that the former are weaker when the initial state is extended in more coordinates. This study is of direct application to the research of intermediate band solar cells and other semiconductor devices based on light absorption in semiconductors nanostructured with quantum dots.

Oxygen extended sooting index of FAME blends with aviation kerosene

The use of biofuels in the aviation sector has economic and environmental benefits. Among the options for the production of renewable jet fuels, hydroprocessed esters and fatty acids (HEFA) have received predominant attention in comparison with fatty acid methyl esters (FAME), which are not approved as additives for jet fuels. However, the presence of oxygen in methyl esters tends to reduce soot emissions and therefore particulate matter emissions. This sooting tendency is quantified in this work with an oxygen-extended sooting index, based on smoke point measurements. Results have shown considerable reduction in the sooting tendency for all biokerosenes (produced by transesterification and eventually distillation) with respect to fossil kerosenes. Among the tested biokerosenes, that made from palm kernel oil was the most effective one, and nondistilled methyl esters (from camelina and linseed oils) showed lower effectiveness than distilled biokerosenes to reduce the sooting tendency. These results may constitute an additional argument for the use of FAME’s as blend components of jet fuels. Other arguments were pointed out in previous publications, but some controversy has aroused over the use of these components. Some of the criticism was based on the fact that the methods used in our previous work are not approved for jet fuels in the standard methods and concluded that the use of FAME in any amount is, thus, inappropriate. However, some of the standard methods are not updated for considering oxygenated components (like the method for obtaining the lower heating value), and others are not precise enough (like the methods for measuring the freezing point), whereas some alternative methods may provide better reproducibility for oxygenated fuels.

Hoshin Kanri. Principle Centered Leadership

The purpose of this paper is to sketch the outlines of what will, hopefully become my PhD thesis: the proposal of an evolutional leadership behavioral pattern, Hoshin Kanri, that enables process owners in organizations attain alignment by achieving their goals while increasing trust. ! I intend to develop such a behavioral pattern or “proper way” 善道 1 by adopting a network perspective over two organizational dimensions: process dimension and process owner dimension. In both dimensions I will propose measures of their topological structure and functionality. From there I will propose quantifiable characteristics that will help me enunciate several hypothesis about their dynamical and evolutional characteristics. I intend to test these hypothesis in the field and report the results to enable others to challenge this research.

On the harmonic analysis of cup anemometer rotation speed: A principle to monitor performance and maintenance status of rotating meteorological sensors

The calibration results of one anemometer equipped with several rotors, varying their size, were analyzed. In each case, the 30-pulses pert turn output signal of the anemometer was studied using Fourier series decomposition and correlated with the anemometer factor (i.e., the anemometer transfer function). Also, a 3-cup analytical model was correlated to the data resulting from the wind tunnel measurements. Results indicate good correlation between the post-processed output signal and the working condition of the cup anemometer. This correlation was also reflected in the results from the proposed analytical model. With the present work the possibility of remotely checking cup anemometer status, indicating the presence of anomalies and, therefore, a decrease on the wind sensor reliability is revealed.

Design and optimization of optical, fiber based PSK demodulators for high-bit-rate optical networks

El objetivo principal de esta tesis ha sido el diseño y la optimización de receptores implementados con fibra óptica, para ser usados en redes ópticas de alta velocidad que empleen formatos de modulación de fase. En los últimos años, los formatos de modulación de fase (Phase Shift keying, PSK) han captado gran atención debido a la mejora de sus prestaciones respecto a los formatos de modulación convencionales. Principalmente, presentan una mejora de la eficiencia espectral y una mayor tolerancia a la degradación de la señal causada por la dispersión cromática, la dispersión por modo de polarización y los efectos no-lineales en la fibra óptica. En este trabajo, se analizan en detalle los formatos PSK, incluyendo sus variantes de modulación de fase diferencial (Differential Phase Shift Keying, DPSK), en cuadratura (Differential Quadrature Phase Shift Keying, DQPSK) y multiplexación en polarización (Polarization Multiplexing Differential Quadrature Phase Shift Keying, PM-DQPSK), con la finalidad de diseñar y optimizar los receptores que permita su demodulación. Para ello, se han analizado y desarrollado nuevas estructuras que ofrecen una mejora en las prestaciones del receptor y una reducción de coste comparadas con las actualmente disponibles. Para la demodulación de señales DPSK, en esta tesis, se proponen dos nuevos receptores basados en un interferómetro en línea Mach-Zehnder (MZI) implementado con tecnología todo-fibra. El principio de funcionamiento de los MZI todo-fibra propuestos se asienta en la interferencia modal que se produce en una fibra multimodo (MMF) cuando se situada entre dos monomodo (SMF). Este tipo de configuración (monomodo-multimodo-monomodo, SMS) presenta un buen ratio de extinción interferente si la potencia acoplada en la fibra multimodo se reparte, principal y equitativamente, entre dos modos dominantes. Con este objetivo, se han estudiado y demostrado tanto teórica como experimentalmente dos nuevas estructuras SMS que mejoran el ratio de extinción. Una de las propuestas se basa en emplear una fibra multimodo de índice gradual cuyo perfil del índice de refracción presenta un hundimiento en su zona central. La otra consiste en una estructura SMS con las fibras desalineadas y donde la fibra multimodo es una fibra de índice gradual convencional. Para las dos estructuras, mediante el análisis teórico desarrollado, se ha demostrado que el 80 – 90% de la potencia de entrada se acopla a los dos modos dominantes de la fibra multimodo y se consigue una diferencia inferior al 10% entre ellos. También se ha demostrado experimentalmente que se puede obtener un ratio de extinción de al menos 12 dB. Con el objeto de demostrar la capacidad de estas estructuras para ser empleadas como demoduladores de señales DPSK, se han realizado numerosas simulaciones de un sistema de transmisión óptico completo y se ha analizado la calidad del receptor bajo diferentes perspectivas, tales como la sensibilidad, la tolerancia a un filtrado óptico severo o la tolerancia a las dispersiones cromática y por modo de polarización. En todos los casos se ha concluido que los receptores propuestos presentan rendimientos comparables a los obtenidos con receptores convencionales. En esta tesis, también se presenta un diseño alternativo para la implementación de un receptor DQPSK, basado en el uso de una fibra mantenedora de la polarización (PMF). A través del análisi teórico y del desarrollo de simulaciones numéricas, se ha demostrado que el receptor DQPSK propuesto presenta prestaciones similares a los convencionales. Para complementar el trabajo realizado sobre el receptor DQPSK basado en PMF, se ha extendido el estudio de su principio de demodulación con el objeto de demodular señales PM-DQPSK, obteniendo como resultado la propuesta de una nueva estructura de demodulación. El receptor PM-DQPSK propuesto se basa en la estructura conjunta de una única línea de retardo junto con un rotador de polarización. Se ha analizado la calidad de los receptores DQPSK y PM-DQPSK bajo diferentes perspectivas, tales como la sensibilidad, la tolerancia a un filtrado óptico severo, la tolerancia a las dispersiones cromática y por modo de polarización o su comportamiento bajo condiciones no-ideales. En comparación con los receptores convencionales, nuestra propuesta exhibe prestaciones similares y además permite un diseño más simple que redunda en un coste potencialmente menor. En las redes de comunicaciones ópticas actuales se utiliza la tecnología de multimplexación en longitud de onda (WDM) que obliga al uso de filtros ópticos con bandas de paso lo más estrechas posibles y a emplear una serie de dispositivos que incorporan filtros en su arquitectura, tales como los multiplexores, demultiplexores, ROADMs, conmutadores y OXCs. Todos estos dispositivos conectados entre sí son equivalentes a una cadena de filtros cuyo ancho de banda se va haciendo cada vez más estrecho, llegando a distorsionar la forma de onda de las señales. Por esto, además de analizar el impacto del filtrado óptico en las señales de 40 Gbps DQPSK y 100 Gbps PM-DQPSK, este trabajo de tesis se completa estudiando qué tipo de filtro óptico minimiza las degradaciones causadas en la señal y analizando el número máximo de filtros concatenados que permiten mantener la calidad requerida al sistema. Se han estudiado y simulado cuatro tipos de filtros ópticos;Butterworth, Bessel, FBG y F-P. ABSTRACT The objective of this thesis is the design and optimization of optical fiber-based phase shift keying (PSK) demodulators for high-bit-rate optical networks. PSK modulation formats have attracted significant attention in recent years, because of the better performance with respect to conventional modulation formats. Principally, PSK signals can improve spectrum efficiency and tolerate more signal degradation caused by chromatic dispersion, polarization mode dispersion and nonlinearities in the fiber. In this work, many PSK formats were analyzed in detail, including the variants of differential phase modulation (Differential Phase Shift Keying, DPSK), in quadrature (Differential Quadrature Phase Shift Keying, DQPSK) and polarization multiplexing (Polarization Multiplexing Differential Quadrature Phase Shift Keying, PM-DQPSK), in order to design and optimize receivers enabling demodulations. Therefore, novel structures, which offer good receiver performances and a reduction in cost compared to the current structures, have been analyzed and developed. Two novel receivers based on an all-fiber in-line Mach-Zehnder interferometer (MZI) were proposed for DPSK signal demodulation in this thesis. The operating principle of the all-fiber MZI is based on the modal interference that occurs in a multimode fiber (MMF) when it is located between two single-mode fibers (SMFs). This type of configuration (Single-mode-multimode-single-mode, SMS) can provide a good extinction ratio if the incoming power from the SMF could be coupled equally into two dominant modes excited in the MMF. In order to improve the interference extinction ratio, two novel SMS structures have been studied and demonstrated, theoretically and experimentally. One of the two proposed MZIs is based on a graded-index multimode fiber (MMF) with a central dip in the index profile, located between two single-mode fibers (SMFs). The other one is based on a conventional graded-index MMF mismatch spliced between two SMFs. Theoretical analysis has shown that, in these two schemes, 80 – 90% of the incoming power can be coupled into the two dominant modes exited in the MMF, and the power difference between them is only ~10%. Experimental results show that interference extinction ratio of 12 dB could be obtained. In order to demonstrate the capacity of these two structures for use as DPSK signal demodulators, numerical simulations in a completed optical transmission system have been carried out, and the receiver quality has been analyzed under different perspectives, such as sensitivity, tolerance to severe optical filtering or tolerance to chromatic and polarization mode dispersion. In all cases, from the simulation results we can conclude that the two proposed receivers can provide performances comparable to conventional ones. In this thesis, an alternative design for the implementation of a DQPSK receiver, which is based on a polarization maintaining fiber (PMF), was also presented. To complement the work made for the PMF-based DQPSK receiver, the study of the demodulation principle has been extended to demodulate PM-DQPSK signals, resulting in the proposal of a novel demodulation structure. The proposed PM-DQPSK receiver is based on only one delay line and a polarization rotator. The quality of the proposed DQPSK and PM-DQPSK receivers under different perspectives, such as sensitivity, tolerance to severe optical filtering, tolerance to chromatic dispersion and polarization mode dispersion, or behavior under non-ideal conditions. Compared with the conventional receivers, our proposals exhibit similar performances but allow a simpler design which can potentially reduce the cost. The wavelength division multiplexing (WDM) technology used in current optical communications networks requires the use of optical filters with a passband as narrow as possible, and the use of a series of devices that incorporate filters in their architecture, such as multiplexers, demultiplexers, switches, reconfigurable add-drop multiplexers (ROADMs) and optical cross-connects (OXCs). All these devices connected together are equivalent to a chain of filters whose bandwidth becomes increasingly narrow, resulting in distortion to the waveform of the signals. Therefore, in addition to analyzing the impact of optical filtering on signal of 40 Gbps DQPSK and 100 Gbps PM-DQPSK, we study which kind of optical filter minimizes the signal degradation and analyze the maximum number of concatenated filters for maintaining the required quality of the system. Four types of optical filters, including Butterworth, Bessel, FBG and FP, have studied and simulated.

Extended phone log-likelihood ratio features and acoustic-based I-vectors for language recognition

This paper presents new techniques with relevant improvements added to the primary system presented by our group to the Albayzin 2012 LRE competition, where the use of any additional corpora for training or optimizing the models was forbidden. In this work, we present the incorporation of an additional phonotactic subsystem based on the use of phone log-likelihood ratio features (PLLR) extracted from different phonotactic recognizers that contributes to improve the accuracy of the system in a 21.4% in terms of Cavg (we also present results for the official metric during the evaluation, Fact). We will present how using these features at the phone state level provides significant improvements, when used together with dimensionality reduction techniques, especially PCA. We have also experimented with applying alternative SDC-like configurations on these PLLR features with additional improvements. Also, we will describe some modifications to the MFCC-based acoustic i-vector system which have also contributed to additional improvements. The final fused system outperformed the baseline in 27.4% in Cavg.

Persuasive system design methods to deliver a cardio-rehabilitation program of post mi outpatients

Las enfermedades no transmisibles provocan cada ano 38 millones de fallecimientos en el mundo. Entre ellas, tan solo cuatro enfermedades son responsables del 82% de estas muertes: las enfermedades cardiovasculares, las enfermedades crónicas respiratorias, la diabetes, y el cáncer. Se prevé que estas cifras aumenten en los próximos anos, ya que las tendencias indican que en el año 2030 las muertes por esta causa ascenderán a 53 millones de personas. La Organización Mundial de la Salud (OMS) considera importante buscar soluciones para afrontar esta situación y ha solicitado a los gobiernos del mundo la implementación de intervenciones para mejorar los hábitos de vida de las personas y reducir así el riesgo de desarrollo de enfermedades no trasmisibles. Cada año se producen 32 millones de infartos de miocardio y derrames celebrales, de los cuales 12.5 son mortales. En el mundo entre el 40% y 75% de la víctimas de un infarto de miocardio mueren antes de su ingreso en el hospital. En los casos que sobreviven, la adopción de un estilo de vida saludable puede evitar infartos sucesivo, y supone un ahorro potencial de 6 billones de euros al año. La rehabilitación cardiaca es un programa individualizado que aplica un método multidisciplinar para ayudar al paciente a recuperar su condición física, a gestionar la enfermedad cardiovascular y sus comorbilidades, a adoptar hábitos de vida saludables, y a promover su salud mental. La rehabilitación cardiaca requiere la total involucración y motivación del paciente, solo de esta manera se podrán promover hábitos saludables y mejorar la gestión y prevención de su enfermedad. Aunque la participación en los programas de rehabilitación cardiaca es baja, hoy en día existen programas de rehabilitación cardiaca que el paciente puede realizar en su casa. Estos suponen una solución prometedora para aumentar la participación. La rehabilitación cardiaca se considera una intervención integral donde los modelos de psicología de la salud son aplicados para promover un cambio en el estilo de vida de las personas así como para ayudarles a afrontar su propia enfermedad. Existen métodos para implementar cambios de hábitos y de aptitud, y también se considera muy relevante promover no solo el bienestar físico sino también el mental. Existen tecnologías que promueven los cambios de comportamientos en los seres humanos. En concreto, las tecnologías persuasivas y los sistemas de apoyo al cambio de comportamientos modelan las características, las estrategias y los métodos de diseño para promover cambios usando la tecnología. Pero estos modelos tienen algunas limitaciones: todavía no se ha definido que rol tienen las emociones en el cambio de comportamientos y como traducir los métodos de la psicología de la salud en la tecnología. Esta tesis se centra en tres elementos que tienen un rol clave en los cambios de hábitos y actitud: el estado físico, el estado mental, y la tecnología. -Estado de salud: un estado de salud critico puede modificar la actitud del ser humano respecto al cambio. A la vez un buen estado de salud hace que la necesidad del cambio sea menos percibida. -Estado emocional: la actitud tiene un componente afectivo. Los estados emocionales negativos pueden reducir la habilidad de una persona para adoptar nuevos comportamientos. La salud mental es la situación ideal donde los individuos tienen predisposición a los cambios. La tecnología puede ayudar a las personas a adoptar nuevos hábitos, así como a mantener una salud física y mental. Este trabajo de investigación se centra en el diseño de tecnologías para la mejora del estado físico y emocional de las personas. Se ha propuesto un marco de diseño llamado “Well.Be.Sign”. El marco se basa en tres aspectos: El marco teórico: representa los elementos que se tienen que definir para diseñar tecnologías para promover el bienestar de las personas. -El diagrama de influencia: presenta las fuerzas de ‘persuasión’ en el contexto de la salud. El rol de las tecnologías persuasivas ha sido contextualizado en una dimensión donde otros elementos influencian el usuario.  El proceso de diseño: describe el proceso de diseño utilizando una metodología iterativa e incremental que aplica una combinación de métodos de diseño existentes (Diseño Orientado a Objetivos, Diseño de Sistemas Persuasivos) así como elementos originales de este trabajo de investigación. Los métodos se han aplicados para diseñar un sistema que ofrezca un programa de tele-rehabilitación cardiaca. Inicialmente se ha diseñado un prototipo de acuerdo con las necesidades del usuario. En segundo lugar, el prototipo se ha extendido especificando la intervención requerida para al programa de rehabilitación cardiaca. Finalmente el sistema se ha desarrollado y validado en un ensayo clínico con grupo control, donde se observaron las variaciones del estado cardiovascular, el nivel de conocimiento acerca de la enfermedad, la percepción de la enfermedad, la persistencia de hábitos saludables, y la aceptabilidad del sistema. Los resultados muestran que el grupo de intervención tiene una superior capacidad cardiovascular, mejor conocimiento acerca de la enfermedad, y más percepción de control de la enfermedad. Asimismo, en algunos casos se ha registrado persistencia de los hábitos de ejercicios 6 meses después del uso del sistema. Otros dos estudios se han presentado para demonstrar la relevancia del estado emocional del usuario en el diseño de aplicaciones para la promoción del bienestar.  En personas con una grave enfermedad crónica como la insuficiencia cardiaca, donde se ha presentado las conexiones entre estado de salud y estado emocional. En el estudio se ensena la relaciones que tienen los síntomas y las emociones negativas y como un estado negativo emocional puede empeorar la condición física del paciente. -Personas con trastornos del humor: el estudio muestra como las emociones pueden tener un impacto en la percepción de la tecnología por parte del usuario. ABSTRACT Noncommunicable diseases (NCDs) cause the death of 38 million people every year. Four major NCDs are responsible for 82% of these deaths: cardio vascular disease, chronic respiratory disease, diabetes and cancer. These pandemic numbers are projected to raise to 53 million deaths in 2030, and for this reason the assembly of the World Health Organization (WHO) considers communicable diseases as an urgent need to be addressed. It is also a trend to advocate the adoption of mobile technology to deliver health services and to promote healthy behaviours among citizens, but adopting healthS promoting lifestyle is still a difficult task facing human tendencies. Within this context, there is a promising opportunity: persuasive technologies. These technologies are intentionally designed to change a person’s attitudes or behaviours; when applied in this context, than can be used to change health-related attitudes, beliefs, and behaviours. Each year there are 32 million heart attacks and strokes globally, of which about 12.5 million are fatal. Worldwide between 40 and 75% of all heart-attack victims die before reaching hospital. Avoiding a second heart attack by improving adherence to lifestyle and medication regimens has a cost saving potential of around €6 billion per year. In most of the cases the cardiovascular event has been provoked by unhealthy lifestyle. Furthermore, after an MI event the patient's decision to adopt or not healthier behaviour will influence the progress of the disease. Cardio-rehabilitation is an individualized program that follows a multidisciplinary approach to support the user to recover from the Myocardial Infarction, manage the Cardio Vascular Disease and the comorbidities, adopt healthy habits, and cope with any emotional distress. Cardio- rehabilitation requires patient participation and willingness to perform behavioral modifications and change the attitude toward the management and prevention of the disease. Participation in the Cardio Rehabilitation program is not high; the home-based rehabilitation program is a promising solution to increase participation. Nowadays cardio rehabilitation is considered a comprehensive intervention in which models of health psychology are applied to promote the behaviour change of the individuals. Relevant methods that have been successfully applied to foster healthy habits include the Health Belief Model and the Trans Theoretical Model. Studies also demonstrate the importance to promote not only the physical but also the mental well being of the individuals. The idea of also promoting behaviour change using technologies has been defined by the literature as persuasive technologies or behaviour change support systems, in which the features, the strategies and the design method have been modelled to foster the behaviour change using technology. Limitations have been found in this model: there is still research to be done on the role of the emotions and how psychological health intervention can be translated into computer methods. This research focuses on three elements that could foster behaviour change in individuals: the physical and emotional status of the person, and the technology. Every component can influence the user's attitude and behaviour in the following ways: ' Physical status: bad physical status could change human attitude toward the necessity to adopt health behaviours; at the same time, good health status reduces the need to adopt healthy habits. ' Emotional status: the attitude has an affective component, negative emotional state can reduce the ability of a person to adopt new behaviours, and mental well being is the ideal situation in which individuals have a predisposition to adopt healthy behaviours. ' Technology: it can help users to adopt new behaviours and can also be support to promote physical and emotional status. Following this approach the idea driven in this research is that technology that is designed to improve the physical status and the emotional status of the individual could better foster behaviour change. According to this principle, the Well.Be.Sign framework has been proposed. The framework is based on three views: ' The theoretical framework: it represents the patterns that have to be defined to design the technologies to promote well being. ' The influence diagram: it shows the persuasive forces in the context of health care. The role of the persuasive technologies is contextualized in a wider universe where other factors and persuasive forces influence a patient. ' The design process: it shows the process of design using an iterative, incremental methodology that applies a combination of existing methodologies (Goal Directed Design and Persuasive System Design) and others that are original to this research. The methods have been applied to design a system to deliver cardio rehabilitation at home: first a prototype has been defined according to the user’s needs, then it has been extended with the specific intervention required for the cardio–rehabilitation, finally the system has been developed and validated in a controlled clinical study in which the cardiovascular fitness, the level of knowledge, the perception of the illness, the persistence of healthy habits and the system acceptance (only the intervention group) were measured. The results show that the intervention group increased cardiovascular capacity, knowledge, feeling of control of illness and perceived benefits of exercise at the end of the study. After six months of the study, a followSup of the exercise habits was performed. Some individuals of the intervention group continued to be engaged in the running exercise sessions promoted in the designed system. Two other cases have been presented to demonstrate the foundations of the Well.Be.Sign’s approach to promote both physical and emotional status: ' People affected by Heart Failure, in which a bidirectional connection between health status and emotions has been discussed with patients. Two correlations were demonstrated: the relationship between symptoms and negative emotional response, and that negative emotional status is correlated with worsening of chronic conditions. ' People with mood disorders: the study shows that emotions could also impact how the user perceives the technology.

The extended Betz–Lanchester limit

A proposal for an extended formulation of the power coefficient of a wind turbine is presented. This new formulation is a generalization of the Betz–Lanchester expression for the power coefficient as function of the axial deceleration of the wind speed provoked by the wind turbine in operation. The extended power coefficient takes into account the benefits of the power produced and the cost associated to the production of this energy. By the simple model proposed is evidenced that the purely energetic optimum operation condition giving rise to the Betz–Lanchester limit (maximum energy produced) does not coincide with the global optimum operational condition (maximum benefit generated) if cost of energy and degradation of the wind turbine during operation is considered. The new extended power coefficient is a general parameter useful to define global optimum operation conditions for wind turbines, considering not only the energy production but also the maintenance cost and the economic cost associated to the life reduction of the machine.

Hidrodinamica de planeadores submarinos y su impacto en la funcionalidad de sensores CTD

Los recientes desarrollos tecnológicos permiten la transición de la oceanografía observacional desde un concepto basado en buques a uno basado en sistemas autónomos en red. Este último, propone que la forma más eficiente y efectiva de observar el océano es con una red de plataformas autónomas distribuidas espacialmente y complementadas con sistemas de medición remota. Debido a su maniobrabilidad y autonomía, los planeadores submarinos están jugando un papel relevante en este concepto de observaciones en red. Los planeadores submarinos fueron específicamente diseñados para muestrear vastas zonas del océano. Estos son robots con forma de torpedo que hacen uso de su forma hidrodinámica, alas y cambios de flotabilidad para generar movimientos horizontales y verticales en la columna de agua. Un sensor que mide conductividad, temperatura y profundidad (CTD) constituye un equipamiento estándar en la plataforma. Esto se debe a que ciertas variables dinámicas del Océano se pueden derivar de la temperatura, profundidad y salinidad. Esta última se puede estimar a partir de las medidas de temperatura y conductividad. La integración de sensores CTD en planeadores submarinos no esta exenta de desafíos. Uno de ellos está relacionado con la precisión de los valores de salinidad derivados de las muestras de temperatura y conductividad. Específicamente, las estimaciones de salinidad están significativamente degradadas por el retardo térmico existente, entre la temperatura medida y la temperatura real dentro de la celda de conductividad del sensor. Esta deficiencia depende de las particularidades del flujo de entrada al sensor, su geometría y, también se ha postulado, del calor acumulado en las capas de aislamiento externo del sensor. Los efectos del retardo térmico se suelen mitigar mediante el control del flujo de entrada al sensor. Esto se obtiene generalmente mediante el bombeo de agua a través del sensor o manteniendo constante y conocida su velocidad. Aunque recientemente se han incorporado sistemas de bombeo en los CTDs a bordo de los planeadores submarinos, todavía existen plataformas equipadas con CTDs sin dichos sistemas. En estos casos, la estimación de la salinidad supone condiciones de flujo de entrada al sensor, razonablemente controladas e imperturbadas. Esta Tesis investiga el impacto, si existe, que la hidrodinámica de los planeadores submarinos pudiera tener en la eficiencia de los sensores CTD. Específicamente, se investiga primero la localización del sensor CTD (externo al fuselaje) relativa a la capa límite desarrollada a lo largo del cuerpo del planeador. Esto se lleva a cabo mediante la utilización de un modelo acoplado de fluido no viscoso con un modelo de capa límite implementado por el autor, así como mediante un programa comercial de dinámica de fluidos computacional (CFD). Los resultados indican, en ambos casos, que el sensor CTD se encuentra fuera de la capa límite, siendo las condiciones del flujo de entrada las mismas que las del flujo sin perturbar. Todavía, la velocidad del flujo de entrada al sensor CTD es la velocidad de la plataforma, la cual depende de su hidrodinámica. Por tal motivo, la investigación se ha extendido para averiguar el efecto que la velocidad de la plataforma tiene en la eficiencia del sensor CTD. Con este propósito, se ha desarrollado un modelo en elementos finitos del comportamiento hidrodinámico y térmico del flujo dentro del CTD. Los resultados numéricos indican que el retardo térmico, atribuidos originalmente a la acumulación de calor en la estructura del sensor, se debe fundamentalmente a la interacción del flujo que atraviesa la celda de conductividad con la geometría interna de la misma. Esta interacción es distinta a distintas velocidades del planeador submarino. Específicamente, a velocidades bajas del planeador (0.2 m/s), la mezcla del flujo entrante con las masas de agua remanentes en el interior de la celda, se ralentiza debido a la generación de remolinos. Se obtienen entonces desviaciones significantes entre la salinidad real y aquella estimada. En cambio, a velocidades más altas del planeador (0.4 m/s) los procesos de mezcla se incrementan debido a la turbulencia e inestabilidades. En consecuencia, la respuesta del sensor CTD es mas rápida y las estimaciones de la salinidad mas precisas que en el caso anterior. Para completar el trabajo, los resultados numéricos se han validado con pruebas experimentales. Específicamente, se ha construido un modelo a escala del sensor CTD para obtener la confirmación experimental de los modelos numéricos. Haciendo uso del principio de similaridad de la dinámica que gobierna los fluidos incompresibles, los experimentos se han realizado con flujos de aire. Esto simplifica significativamente la puesta experimental y facilita su realización en condiciones con medios limitados. Las pruebas experimentales han confirmado cualitativamente los resultados numéricos. Más aun, se sugiere en esta Tesis que la respuesta del sensor CTD mejoraría significativamente añadiendo un generador de turbulencia en localizaciones adecuadas al interno de la celda de conductividad. ABSTRACT Recent technological developments allow the transition of observational oceanography from a ship-based to a networking concept. The latter suggests that the most efficient and effective way to observe the Ocean is through a fleet of spatially distributed autonomous platforms complemented by remote sensing. Due to their maneuverability, autonomy and endurance at sea, underwater gliders are already playing a significant role in this networking observational approach. Underwater gliders were specifically designed to sample vast areas of the Ocean. These are robots with a torpedo shape that make use of their hydrodynamic shape, wings and buoyancy changes to induce horizontal and vertical motions through the water column. A sensor to measure the conductivity, temperature and depth (CTD) is a standard payload of this platform. This is because certain ocean dynamic variables can be derived from temperature, depth and salinity. The latter can be inferred from measurements of temperature and conductivity. Integrating CTD sensors in glider platforms is not exempted of challenges. One of them, concerns to the accuracy of the salinity values derived from the sampled conductivity and temperature. Specifically, salinity estimates are significantly degraded by the thermal lag response existing between the measured temperature and the real temperature inside the conductivity cell of the sensor. This deficiency depends on the particularities of the inflow to the sensor, its geometry and, it has also been hypothesized, on the heat accumulated by the sensor coating layers. The effects of thermal lag are usually mitigated by controlling the inflow conditions through the sensor. Controlling inflow conditions is usually achieved by pumping the water through the sensor or by keeping constant and known its diving speed. Although pumping systems have been recently implemented in CTD sensors on board gliders, there are still platforms with unpumped CTDs. In the latter case, salinity estimates rely on assuming reasonable controlled and unperturbed flow conditions at the CTD sensor. This Thesis investigates the impact, if any, that glider hydrodynamics may have on the performance of onboard CTDs. Specifically, the location of the CTD sensor (external to the hull) relative to the boundary layer developed along the glider fuselage, is first investigated. This is done, initially, by applying a coupled inviscid-boundary layer model developed by the author, and later by using a commercial software for computational fluid dynamics (CFD). Results indicate, in both cases, that the CTD sensor is out of the boundary layer, being its inflow conditions those of the free stream. Still, the inflow speed to the CTD sensor is the speed of the platform, which largely depends on its hydrodynamic setup. For this reason, the research has been further extended to investigate the effect of the platform speed on the performance of the CTD sensor. A finite element model of the hydrodynamic and thermal behavior of the flow inside the CTD sensor, is developed for this purpose. Numerical results suggest that the thermal lag effect is mostly due to the interaction of the flow through the conductivity cell and its geometry. This interaction is different at different speeds of the glider. Specifically, at low glider speeds (0.2 m/s), the mixing of recent and old waters inside the conductivity cell is slowed down by the generation of coherent eddy structures. Significant departures between real and estimated values of the salinity are found. Instead, mixing is enhanced by turbulence and instabilities for high glider speeds (0.4 m/s). As a result, the thermal response of the CTD sensor is faster and the salinity estimates more accurate than for the low speed case. For completeness, numerical results have been validated against model tests. Specifically, a scaled model of the CTD sensor was built to obtain experimental confirmation of the numerical results. Making use of the similarity principle of the dynamics governing incompressible fluids, experiments are carried out with air flows. This significantly simplifies the experimental setup and facilitates its realization in a limited resource condition. Model tests qualitatively confirm the numerical findings. Moreover, it is suggested in this Thesis that the response of the CTD sensor would be significantly improved by adding small turbulators at adequate locations inside the conductivity cell.