Wheel-Rail Contact Forces in High-Speed Simply Supported Bridges at Resonance

The response of high-speed bridges at resonance, particularly under flexural vibrations, constitutes a subject of research for many scientists and engineers at the moment. The topic is of great interest because, as a matter of fact, such kind of behaviour is not unlikely to happen due to the elevated operating speeds of modern rains, which in many cases are equal to or even exceed 300 km/h ( [1,2]). The present paper addresses the subject of the evolution of the wheel-rail contact forces during resonance situations in simply supported bridges. Based on a dimensionless formulation of the equations of motion presented in [4], very similar to the one introduced by Klasztorny and Langer in [3], a parametric study is conducted and the contact forces in realistic situations analysed in detail. The effects of rail and wheel irregularities are not included in the model. The bridge is idealised as an Euler-Bernoulli beam, while the train is simulated by a system consisting of rigid bodies, springs and dampers. The situations such that a severe reduction of the contact force could take place are identified and compared with typical situations in actual bridges. To this end, the simply supported bridge is excited at resonace by means of a theoretical train consisting of 15 equidistant axles. The mechanical characteristics of all axles (unsprung mass, semi-sprung mass, and primary suspension system) are identical. This theoretical train permits the identification of the key parameters having an influence on the wheel-rail contact forces. In addition, a real case of a 17.5 m bridges traversed by the Eurostar train is analysed and checked against the theoretical results. The influence of three fundamental parameters is investigated in great detail: a) the ratio of the fundamental frequency of the bridge and natural frequency of the primary suspension of the vehicle; b) the ratio of the total mass of the bridge and the semi-sprung mass of the vehicle and c) the ratio between the length of the bridge and the characteristic distance between consecutive axles. The main conclusions derived from the investigation are: The wheel-rail contact forces undergo oscillations during the passage of the axles over the bridge. During resonance, these oscillations are more severe for the rear wheels than for the front ones. If denotes the span of a simply supported bridge, and the characteristic distance between consecutive groups of loads, the lower the value of , the greater the oscillations of the contact forces at resonance. For or greater, no likelihood of loss of wheel-rail contact has been detected. The ratio between the frequency of the primary suspension of the vehicle and the fundamental frequency of the bridge is denoted by (frequency ratio), and the ratio of the semi-sprung mass of the vehicle (mass of the bogie) and the total mass of the bridge is denoted by (mass ratio). For any given frequency ratio, the greater the mass ratio, the greater the oscillations of the contact forces at resonance. The oscillations of the contact forces at resonance, and therefore the likelihood of loss of wheel-rail contact, present a minimum for approximately between 0.5 and 1. For lower or higher values of the frequency ratio the oscillations of the contact forces increase. Neglecting the possible effects of torsional vibrations, the metal or composite bridges with a low linear mass have been found to be the ones where the contact forces may suffer the most severe oscillations. If single-track, simply supported, composite or metal bridges were used in high-speed lines, and damping ratios below 1% were expected, the minimum contact forces at resonance could drop to dangerous values. Nevertheless, this kind of structures is very unusual in modern high-speed railway lines.

Influence of the Second Flexural Mode on the Response of High-Speed Bridges

This paper deals with the assessment of the contribution of the second flexural mode to the dynamic behaviour of simply supported railway bridges. Alluding to the works of other authors, it is suggested in some references that the dynamic behaviour of simply supported bridges could be adequately represented taking into account only the contribution of the fundamental flexural mode. On the other hand, the European Rail Research Institute (ERRI) proposes that the second mode should also be included whenever the associated natural frequency is lower than 30 Hz]. This investigation endeavours to clarify the question as much as possible by establishing whether the maximum response of the bridge, in terms of displacements, accelerations and bending moments, can be computed accurately not taking account of the contribution of the second mode. To this end, a dimensionless formulation of the equations of motion of a simply supported beam traversed by a series of equally spaced moving loads is presented. This formulation brings to light the fundamental parameters governing the behaviour of the beam: damping ratio, dimensionless speed $ \alpha$=VT/L, and L/d ratio (L stands for the span of the beam, V for the speed of the train, T represents the fundamental period of the bridge and d symbolises the distance between consecutive loads). Assuming a damping ratio equal to 1%, which is a usual value for prestressed high-speed bridges, a parametric analysis is conducted over realistic ranges of values of $ \alpha$ and L/d. The results can be extended to any simply supported bridge subjected to a train of equally spaced loads in virtue of the so-called Similarity Formulae. The validity of these formulae can be derived from the dimensionless formulation mentioned above. In the parametric analysis the maximum response of the bridge is obtained for one thousand values of speed that cover the range from the fourth resonance of the first mode to the first resonance of the second mode. The response at twenty-one different locations along the span of the beam is compared in order to decide if the maximum can be accurately computed with the sole contribution of the fundamental mode.

Coupled models for the dynamics of bridges under high-speed rail traffic

The dynamic effects of high-speed trains on viaducts are important issues for the design of the structures, as well as for determining safe running conditions of trains. In this work we start by reviewing the relevance of some basic moving load models for the dynamic action of vertical traffic loads. The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require 3D coupled vehicle-bridge models and consideration of wheel to rail contact. We describe here a fully nonlinear coupled model, formulated in absolute coordinates and incorporated into a commercial finite element framework. An application example is presented for a vehicle subject to a strong wind gust traversing a bridge, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Application of the Boundary Element Method to the Analysis of Bridge Abutments

The B.E. technique is applied to an interesting dynamic problem: the interaction between bridges and their abutments. Several two-dimensional cases have been tested in relation with previously published analytical results. A three-dimensional case is also shown and different considerations in relation with the accuracy of the method are described.

Bridge for the airbus A-380 in Barajas airport (Spain)

During the years 2004 and 2005 is has been constructed in Barajas airport of Madrid a special bridge for the new plane AIRBUS A380. This new airplane has a weight of 1,500,000 pounds and 18 wheels with a reaction of 39.2 tonnes per each one and the braking force is about 600 tonnes. The enormous loads transmitted for the airplane made this bridge a special structure. The present article exposes the most important characteristics of project and construction, of one of the special bridges in the airport Brajas of Madri. This bridge was constructed for the access to the hangar of airplanes in Barajas, known "La Muñoza". The structure has a width of 48m, two spans of 13 m each one and a vertical clearance of 5.50 m to allow passing vehicles under it, along thhe new motorway in Brajas (Madrid).

Vibrations of Short Span Railway Bridges for High Speed Lines

The physical model based on moving constant loads is widely used for the analysis of railway bridges. Nevertheless, this model is not well-suited for the study of short span bridges (L<=15-20 m), and the results it produces (displacements and accelerations) are much greater than those obtained experimentally. In this paper two factors are analysed which are believed to have an influence in the dynamic behaviour of short bridges. These two factors are not accounted for by the moving loads model and are the following: the distribution of the loads due to the presence of the sleepers and ballast layer, and the train-bridge interaction. Several numerical simulations have been performed in order to decide on their influence, and the results are presented and discussed herein.

Moving loads on railway bridges: The Spanish Code approach

This paper presents the results of part of the research carried out by a committee in charge of the elaboration of the new Spanish Code of Actions in Railway Bridges. Following the work developed by the European Rail Research Institute (ERRI), the dynamic effects caused by the Spanish high-speed train TALGO have been studied and compared with other European trains. A simplified envelope of the impact coefficient is also presented. Finally, the train-bridge interactions has been analysed and the results compared with those obtained from simple models based on moving loads.

Discussion of "Bibliography and Data on Cable-Stayed Bridges", by the Subcommittee on Cable-Stayed Bridges of the Committee on Long-Span Steel Bridges of the Committee on Metals of the Structural Division (Oct., 1977)

The writer would like to point out the existence of a very remarkable Spanish cable-stayed bridge built in 1925, wich is thus older than the first one recorded by the authors (and probably the pioneer in concrete-deck type). The Tempul Aqueduct was designed by the famous Professor Educardo Torroja. The deck is a concrete box girder sustained by two planes of 3 mm diam 37-wire double cables working at 27 kg/mm2.

A computer program for bridge retrofitting

This paper summarizes the work developed in order to establish a framework for seismic retrofitting of bridges. In this context, the first objetive is to find a numerical model to evaluate the damage induced in a structure, under seismic action, as an index of its vulnerability. The model used has the adventage that is based on concepts of fracture mechanics and concentrated plasticity. As a result, the work is based on basic principles. The performance of this model is being evaluated. Some results of the computer program developed for this purpose are shown.

Dynamic Soil-Structure Interaction in Bridge Abutments

Strong motion obtained in instrumental short-span bridges show the importance of the abutments in the dynamic response of the whole structure. Many models have been used in order to take into account the influence of pier foundations although no reliable ones have been used to analyse the abutment performance. In this work three-dimensional Boundary Element models in frequency domain have been proposed and dimensionless dynamic stiffness of standard bridge abutments have been obtained.

Simplified Procedure for the Nonlinear Seismic Analysis of Bridges

The severe accidents suffered by bridges during recent earthquake show that more careful analysis are needed to guarantee their behaviour. In particular simplified non-linear analysis could be useful to bridge the gap between theoretical research and practical applications. This paper presents one of those simplified methods that can be applied for first designs or to retrofitting of groups of bridges.

Seismic modelling of bridges with semirigid connections

The need to modal semi-rigid behaviour of joints to analyze the seismic response of bridges arises when retrofitting devices such as cables or bolts are introduced in otherwise free joints or when the design takes advantage of the plastification of structural sections to impose energy dissipation though their ductile behaviour. The paper presents some preliminary results of a parametric study carried out using s1mplified computational models. Two instances where semirigid connection play a role in the seismic response of bridges have been discussed. The ongoing research from which this paper is extracted is intended to enhance understanding on the effectivness of various bridge retrofitting measures and to provide information that may be used to calibrate some ECS-2 rules. Finally, it is hoped that the development of reliable simplified techniques for nonlinear analysis will provide designers with useful tools to examine behavior and ultimately improve seismic safety in actual bridges.

The influence of the section shape of box-girder decks on the steady aerodynamic yawing moment of double cantilever bridges under construction

The yawing moment acting on the box-girder deck of reinforced concrete bridges constructed using the balanced cantilever method during the erection stage has been experimentally analyzed by testing different types of bridge cross-sections. Experimental results show that the yawing moment coefficient decreases as the bridge decks become streamlined, and that the yawing moment coefficient reaches a maximum when the bridge deck length is nearly twice the deck width.

Wind-induced loads over double cantilever bridges under construction

Within the last century the interest in wind-induced loads over civil engineering structures has become more and more important, the reason being that the development of new construction techniques and materials has allowed engineers and architects to design new structures far from the traditional concepts, and in many cases wind actions over these singular structures are not included in the existing codes of practice. In this paper the windinduced static loads over bridges constructed by the double cantilever method during erection stages are considered. The aerodynamic load over a double cantilever bridge under a yawing-angled wind produces a yawing (torsional) moment on the bridge deck, which can lead to undesirable rotation of the deck about the supporting pier. The effects of the wind yaw angle and the length of the deck are analysed. The wind action caused by the presence of sliding concrete forms at the ends of the deck is also studied.

An integrated approach to conceptual design of arch bridges with curved deck

El concepto de funicularidad se puede extender a estructuras lineales espaciales como, por ejemplo, los puentes arco con tablero curvo. Estas estructuras, especialmente pasarelas peatonales, son consecuencia de la necesidad de encajar trazados exigentes y de dar respuesta a nuevas demandas arquitectónicas. En las estructuras curvas el diseño conceptual juega un papel absolutamente esencial. Siempre ha sido así, pero en el caso presente, cabe resaltar que una errónea elección de la geometría conlleva una serie de problemas que se irán acumulando a lo largo del proceso de proyecto, de la construcción y de la vida de la estructura. En este trabajo se presenta SOFIA (Shaping Optimal Form with an Interactive Approach), una herramienta capaz de, conocida la geometría del tablero, de buscar automáticamente la forma del arco antifunicular correspondiente. El planteamiento seguido es conceptualmente el mismo que el utilizado en la búsqueda de formas óptimas en estructuras en dos dimensiones: el arco antifunicular es el que representa, para unas cargas dadas, el lugar geométrico de los puntos con momento flector nulo. La herramienta ha sido desarrollada en un entorno integrado, interactivo y paramético. Su implementación está ilustrada y unos ejemplos de análisis paramétricos están desarrollados. La posición transversal relativa entre tablero y arco ha sido investigada para obtener la configuración del puente estructuralmente más eficiente. Las pasarelas curvas se han convertido en un problema de ingeniería más común de lo habitual en el contexto de los desarrollos urbanos cuando el cliente está buscando un fuerte componente estético: un diseño conceptual adecuado permite obtener una estructura eficiente y elegante. Spatial arch bridges represent an innovative answer to demands on functionality, structural optimization and aesthetics for curved decks, popular in urban contexts. This thesis presents SOFIA (Shaping Optimal Form with an Interactive Approach), a methodology for conceptual designing of antifunicular spatial arch bridges with curved deck in a parametric, interactive and integrated environment. The approach and its implementation are in-depth described and detailed examples of parametric analyses are illustrated. The optimal deck-arch relative transversal position has been investigated for obtaining the most cost-effective bridge. Curved footbridges have become a more common engineering problem in the context of urban developments when the client is looking for a strong aesthetics component: an appropriate conceptual design allows to obtain an efficient and elegant structure.