A two-dimensional finite element model of front surface current flow in cells under non-uniform, concentrated illumination

A two-dimensional finite element model of current flow in the front surface of a PV cell is presented. In order to validate this model we perform an experimental test. Later, particular attention is paid to the effects of non-uniform illumination in the finger direction which is typical in a linear concentrator system. Fill factor, open circuit voltage and efficiency are shown to decrease with increasing degree of non-uniform illumination. It is shown that these detrimental effects can be mitigated significantly by reoptimization of the number of front surface metallization fingers to suit the degree of non-uniformity. The behavior of current flow in the front surface of a cell operating at open circuit voltage under non-uniform illumination is discussed in detail.

Influence of Current Pulse Shape on Directly Modulated Systems Performance in Metro Area Optical Networks

Due to the fact that a metro network market is very cost sensitive, direct modulated schemes appear attractive. In this paper a CWDM (Coarse Wavelength Division Multiplexing) system is studied in detail by means of an Optical Communication System Design Software; a detailed study of the modulated current shape (exponential, sine and gaussian) for 2.5 Gb/s CWDM Metropolitan Area Networks is performed to evaluate its tolerance to linear impairments such as signal-to-noise-ratio degradation and dispersion. Point-to-point links are investigated and optimum design parameters are obtained. Through extensive sets of simulation results, it is shown that some of these shape pulses are more tolerant to dispersion when compared with conventional gaussian shape pulses. In order to achieve a low Bit Error Rate (BER), different types of optical transmitters are considered including strongly adiabatic and transient chirp dominated Directly Modulated Lasers (DMLs). We have used fibers with different dispersion characteristics, showing that the system performance depends, strongly, on the chosen DML?fiber couple.

Use of DFOT Heat Pulse Method ForWetting Pattern Determination in Drip Irrigation Emitters

Although there are numerous accurate measuring methods to determine soil moisture content in a spot, until very recently there were no precise in situ and in real time methods that were able to measure soil moisture content along a line. By means of the Distributed Fiber Optic Temperature Measurement method or DFOT, the temperature in 0.12 m intervals and long distances (up to 10,000 m) with a high time frequency and an accuracy of +0.2º C is determined. The principle of temperature measurement along a fiber optic cable is based on the thermal sensitivity of the relative intensities of backscattered photons that arise from collisions with electrons in the core of the glass fiber. A laser pulse, generated by the DTS unit, traversing a fiber optic cable will result in backscatter at two frequencies. The DTS quantifies the intensity of these backscattered photons and elapsed time between the pulse and the observed returned light. The intensity of one of the frequencies is strongly dependent on the temperature at the point where the scattering process occurred. The computed temperature is attributed to the position along the cable from which the light was reflected, computed from the time of travel for the light.

Utilización del "dfot heat pulse method" para el estudio del bulbo mojado en goteros

Aunque se conocen muchos métodos precisos para medidas de humedad puntuales, hasta hace muy poco, no existían métodos in situ para la medida del contenido de humedad a escala de metros o de kilómetros, importantes cuando pensamos a nivel de cuenca hidrográfica. La fibra óptica ha sido muy utilizada en el área de las comunicaciones. Sin embargo, entre sus aplicaciones más recientes, destaca la de su uso para medir la temperatura incluso en grandes distancias (hasta 10 km) y con una alta frecuencia temporal, lo que ha abierto un amplio abanico de posibilidades muy importantes en el seguimiento medioambiental (Selker et al. 2006a; 2006b, Tyler et al. 2008; Westhoff et al., 2007; Freifeld et al., 2008). La precisión en la medida puede alcanzar ± 0,2ºC en una distancia de ± 25 cm. El método utilizado en los ensayos explicados en esta comunicación es el denominado “Distributed Fiber Optic Temperature Measurement” (medida distribuida de la temperatura con fibra óptica) o DFOT, que consiste en emitir un impulso óptico con láser y medir en el tiempo la señal reflejada en diferentes puntos de la fibra. Este método se ha utilizado en el estudio de filtraciones de minas abandonadas (Selker et al. 2006a) y en proyectos relacionados con el cambio climático, como en el estudio del deshielo en glaciares y balances hídricos en pequeñas cuencas (Selker et al. 2006b). Además, en medios porosos, se ha usado, con buenos resultados para la detección de rotura de diques en presas (Perzlmaier et al. 2004a y 2004b) y para la detección de entrada de agua en vertederos urbanos con cubierta vegetal (Weiss, 2003b). Imhoff et al. (2006) en su revisión de técnicas de medidas de contenido de agua en el suelo destaca el uso del “DFOT heat pulse method” (método DFOT del pulso de calor).

Hydrodynamic stability theory of double ablation front structures in inertial confinement fusion.

The aim of inertial confinement fusion is the production of energy by the fusion of thermonuclear fuel (deuterium-tritium) enclosed in a spherical target due to its implosion. In the direct-drive approach, the energy needed to spark fusion reactions is delivered by the irradiation of laser beams that leads to the ablation of the outer shell of the target (the so-called ablator). As a reaction to this ablation process, the target is accelerated inwards, and, provided that this implosion is sufficiently strong a symmetric, the requirements of temperature and pressure in the center of the target are achieved leading to the ignition of the target (fusion). One of the obstacles capable to prevent appropriate target implosions takes place in the ablation region where any perturbation can grow even causing the ablator shell break, due to the ablative Rayleigh-Taylor instability. The ablative Rayleigh-Taylor instability has been extensively studied throughout the last 40 years in the case where the density/temperature profiles in the ablation region present a single front (the ablation front). Single ablation fronts appear when the ablator material has a low atomic number (deuterium/tritium ice, plastic). In this case, the main mechanism of energy transport from the laser energy absorption region (low density plasma) to the ablation region is the electron thermal conduction. However, recently, the use of materials with a moderate atomic number (silica, doped plastic) as ablators, with the aim of reducing the target pre-heating caused by suprathermal electrons generated by the laser-plasma interaction, has demonstrated an ablation region composed of two ablation fronts. This fact appears due to increasing importance of radiative effects in the energy transport. The linear theory describing the Rayleigh-Taylor instability for single ablation fronts cannot be applied for the stability analysis of double ablation front structures. Therefore, the aim of this thesis is to develop, for the first time, a linear stability theory for this type of hydrodynamic structures.

Developing front-end Web 2.0 technologies to access services, content and things in the future Internet

The future Internet is expected to be composed of a mesh of interoperable web services accessible from all over the web. This approach has not yet caught on since global user?service interaction is still an open issue. This paper states one vision with regard to next-generation front-end Web 2.0 technology that will enable integrated access to services, contents and things in the future Internet. In this paper, we illustrate how front-ends that wrap traditional services and resources can be tailored to the needs of end users, converting end users into prosumers (creators and consumers of service-based applications). To do this, we propose an architecture that end users without programming skills can use to create front-ends, consult catalogues of resources tailored to their needs, easily integrate and coordinate front-ends and create composite applications to orchestrate services in their back-end. The paper includes a case study illustrating that current user-centred web development tools are at a very early stage of evolution. We provide statistical data on how the proposed architecture improves these tools. This paper is based on research conducted by the Service Front End (SFE) Open Alliance initiative.

Pulse shortening of gain switched single mode semiconductor lasers using a variable delay interferometer

We propose a pulse shaping and shortening technique for pulses generated from gain switched single mode semiconductor lasers, based on a Mach Zehnder interferometer with variable delay. The spectral and temporal characteristics of the pulses obtained with the proposed technique are investigated with numerical simulations. Experiments are performed with a Distributed Feedback laser and a Vertical Cavity Surface Emitting Laser, emitting at 1.5 µm, obtaining pulse duration reduction of 25-30%. The main asset of the proposed technique is that it can be applied to different devices and pulses, taking advantage of the flexibility of the gain switching technique.

High-peak-power pulse generation from a monolithic master oscillator power amplifier at 1.5 μm

We present an experimental study on the generation of high-peak-power short optical pulses from a fully integrated master-oscillator power-amplifier emitting at 1.5 μm. High-peak-power (2.7 W) optical pulses with short duration (100 ps) have been generated by gain switching the master oscillator under optimized driving conditions. The static and dynamic characteristics of the device have been studied as a function of the driving conditions. The ripples appearing in the power-current characteristics under cw conditions have been attributed to mode hopping between the master oscillator resonant mode and the Fabry-Perot modes of the entire device cavity. Although compound cavity effects have been evidenced to affect the static and dynamic performance of the device, we have demonstrated that trains of single-mode short optical pulses at gigahertz frequencies can be conveniently generated in these devices.

Periodic time-domain modulation for the electrically tunable control of optical pulse train envelope and repetition rate multiplication

An electrically tunable system for the control of optical pulse sequences is proposed and demonstrated. It is based on the use of an electrooptic modulator for periodic phase modulation followed by a dispersive device to obtain the temporal Talbot effect. The proposed configuration allows for repetition rate multiplication with different multiplication factors and with the simultaneous control of the pulse train envelope by simply changing the electrical signal driving the modulator. Simulated and experimental results for an input optical pulse train of 10 GHz are shown for different multiplication factors and envelope shapes.

Application of active heat pulse method with fiber optic temperature sensing for estimation of wetting bulbs and water distribution in drip emitters.

Through the use of the Distributed Fiber Optic Temperature Measurement (DFOT) method, it is possible to measure the temperature in small intervals (on the order of centimeters) for long distances (on the order of kilometers) with a high temporal frequency and great accuracy. The heat pulse method consists of applying a known amount of heat to the soil and monitoring the temperature evolution, which is primarily dependent on the soil moisture content. The use of both methods, which is called the active heat pulse method with fiber optic temperature sensing (AHFO), allows accurate soil moisture content measurements. In order to experimentally study the wetting patterns, i.e. shape, size, and the water distribution, from a drip irrigation emitter, a soil column of 0.5 m of diameter and 0.6 m high was built. Inside the column, a fiber optic cable with a stainless steel sheath was placed forming three concentric helixes of diameters 0.2 m, 0.4 m and 0.6 m, leading to a 148 measurement point network. Before, during, and after the irrigation event, heat pulses were performed supplying electrical power of 20 W/m to the steel. The soil moisture content was measured with a capacitive sensor in one location at depths of 0.1 m, 0.2 m, 0.3 m and 0.4 m during the irrigation. It was also determined by the gravimetric method in several locations and depths before and right after the irrigation. The emitter bulb dimensions and shape evolution was satisfactorily measured during infiltration. Furthermore, some bulb's characteristics difficult to predict (e.g. preferential flow) were detected. The results point out that the AHFO is a useful tool to estimate the wetting pattern of drip irrigation emitters in soil columns and show a high potential for its use in the field.

Application of high-intensity short-pulse lasers to the mechanical and surface properties improvement of high reliability metallic components by shock processing

Outline: • Introduction • Process Experimental Setup • Experimental Procedure • Experimental Results for Al2024-T351 and Ti6Al4V - Residual stresses - Tensile Strength - Fatigue Life • Discussion and Outlook - Prospects for technological applications of LSP

Interconexión monolítica de dispositivos fotovoltaicos basados en a-Si mediante ablación directa con fuentes láser ultravioleta

Resumen En la última década la tecnología láser se ha convertido en una herramienta imprescindible en la fabricación de dispositivos fotovoltaicos, muy especial¬mente en aquellos basados en tecnología de lámina delgada. Independiente¬mente de crisis coyunturales en el sector, la evolución en los próximos años de estas tecnologías seguirá aprovechándose de la flexibilidad y calidad de proceso de la herramienta láser para la consecución de los dos objetivos básicos que harán de la fotovoltaica una opción energética económicamente viable: la reducción de costes de fabricación y el aumento de eficiencia de los dispositivos. Dentro de las tecnologías fotovoltaicas de lámina delgada, la tecnología de dispositivos basados en silicio amorfo ha tenido un gran desarrollo en sistemas estándar en configuración de superestrato, pero su limitada efi¬ciencia hace que su supervivencia futura pase por el desarrollo de formatos en configuración de substrato sobre materiales flexibles de bajo coste. En esta aproximación, las soluciones industriales basadas en láser actualmente disponibles para la interconexión monolítica de dispositivos no son aplica¬bles, y desde hace años se viene investigando en la búsqueda de soluciones apropiadas para el desarrollo de dichos procesos de interconexión de forma que sean transferibles a la industria. En este contexto, esta Tesis propone una aproximación completamente orig¬inal, demostrando la posibilidad de ejecutar una interconexión completa de estos dispositivos irradiando por el lado de la lámina (es decir de forma com¬patible con la opción de configuración de substrato y, valga la redundancia, con el substrato del dispositivo opaco), y con fuentes láser emitiendo en UV. Este resultado, obtenido por primera vez a nivel internacional con este trabajo, aporta un conocimiento revelador del verdadero potencial de estas fuentes en el desarrollo industrial futuro de estas tecnologías. Si bien muy posiblemente la solución industrial final requiera de una solución mixta con el empleo de fuentes en UV y, posiblemente, en otras longitudes de onda, esta Tesis y su planteamiento novedoso aportan un conocimiento de gran valor a la comunidad internacional por la originalidad del planteamiento seguido, los resultados parciales encontrados en su desarrollo (un número importante de los cuales han aparecido en revistas del JCR que recogen en la actualidad un número muy significativo de citas) y porque saca además a la luz, con las consideraciones físicas pertinentes, las limitaciones intrínsecas que el desarrollo de procesos de ablación directa selectiva con láseres UV en parte de los materiales utilizados presenta en el rango temporal de in¬teracción de ns y ps. En este trabajo se han desarrollado y optimizado los tres pasos estándar de interconexión (los habitualmente denominados Pl, P2 y P3 en la industria fotovoltaica) demostrando las ventajas y limitaciones del uso de fuentes en UV tanto con ancho temporal de ns como de ps. En particular destaca, por el éxito en los resultados obtenidos, el estudio de procesos de ablación selectiva de óxidos conductores transparentes (en este trabajo utilizados tanto como contacto frontal así como posterior en los módulos) que ha generado resultados, de excelente acogida científica a nivel internacional, cuya aplicación trasciende el ámbito de las tecnologías de silicio amorfo en lámina delgada. Además en este trabajo de Tesis, en el desarrollo del objetivo citado, se han puesto a punto técnicas de análisis de los procesos láser, basadas en métodos avanzados de caracterización de materiales (como el uso combi¬nado de la espectroscopia dispersiva de rayos X y la microscopía confocal de barrido) que se presentan como auténticos avances en el desarrollo de técnicas específicas de caracterización para el estudio de los procesos con láser de ablación selectiva de materiales en lámina delgada, procesos que no solo tienen impacto en el ámbito de la fotovoltaica, sino también en la microelectrónica, la biotecnología, la microfabricación, etc. Como resultado adicional, parte de los resultados de este trabajo, han sido aplicados exi¬tosamente por el grupo de investigaci´on en la que la autora desarrolla su labor para conseguir desarrollar procesos de enorme inter´es en otras tec-nolog´ıas fotovoltaicas, como las tecnolog´ıas est´andar de silicio amorfo sobre vidrio en configuraci´on de superestrato o el procesado de capas delgadas en tecnolog´ıas convencionales de silicio cristalino. Por u´ltimo decir que este trabajo ha sido posible por una colaboraci´on muy estrecha entre el Centro L´aser de la UPM, en el que la autora de¬sarrolla su labor, y el Grupo de Silicio Depositado del Centro de Inves¬tigaciones Energ´eticas, Medioambientales y Tecnol´ogicas, CIEMAT, que, junto al Grupo de Energ´ıa Fotovoltaica de la Universidad de Barcelona, han preparado la mayor parte de las muestras utilizadas en este estudio. Dichas colaboraciones se han desarrollado en el marco de varios proyectos de investigaci´on aplicada con subvenci´on pu´blica, tales como el proyecto singular estrat´egico PSE-MICROSIL08 (PSE-120000-2006-6), el proyecto INNDISOL (IPT-420000-2010-6), ambos financiados porel Fondo Europeo de Desarrollo Regional FEDER (UE) ”Una manera de hacer Europa y el MICINN, y los proyectos de Plan Nacional AMIC (ENE2010-21384-C04-´ 02) y CLASICO (ENE2007-6772-C04-04), cuya financiaci´on ha permitido en gran parte llevar a t´ermino este trabajo Abstract In the last decade, the laser technology has turned into an indispensable tool in the production of photovoltaic devices, especially of those based on thin film technology. Regardless the current crisis in the sector, the evolution of these technologies in the upcoming years will keep taking advantage of the flexibility and process quality of the laser tool for the accomplishment of the two basic goals that will convert the photovoltaic energy into economically viable: the manufacture cost reduction and the increase in the efficiency of the devices. Amongst the thin film laser technologies, the technology of devices based on amorphous silicon has had a great development in standard systems of superstrate configuration, but its limited efficiency makes its survival de¬pendant on the development of formats in substrate configuration with low cost flexible materials. In this approach, the laser industrial solutions cur¬rently available for the monolithic interconnection are not applicable, and in the last few years the investigations have been focused on the search of appropriate solutions for the development of such interconnection processes in a way that the same are transferable to the industry. In this context, this Thesis proposes a totally original approach, proving the possibility of executing a full interconnection of these devices by means of irradiation from the film side, i.e., compatible with the substrate con¬figuration, and with UV laser sources. This result, obtained for the first time at international level in this work, provides a revealing knowledge of the true potential of these sources in the future industrial development of these technologies. Even though very probably the final industrial solution will require a combination of the use of UV sources along with other wave¬lengths, this Thesis and its novel approach contribute with a high value to the international community because of the originality of the approach, the partial results found throughout its development (out of which, a large number has appeared in JCR journals that currently accumulate a signifi¬cant number of citations) and brings to light, with the pertinent scientific considerations, the intrinsic limitations that the selective direct ablation processes with UV laser present in the temporal range of interaction of ns and ps for part of the materials used in this study. More particularly, the three standard steps of interconnection (usually de¬nominated P1, P2 and P3 in the photovoltaic industry) have been developed and optimized, showing the advantages as well as the limitations of the use of UV sources in both the ns and ps pulse-width ranges. It is highly remark¬able, because of the success in the obtained results, the study of selective ablation processes in transparent conductive oxide (in this work used as a front and back contact), that has generated results, of excellent interna¬tional scientific reception, whose applications go beyond the scope of thin film photovoltaic technologies based on amorphous silicon. Moreover, in this Thesis, with the development of the mentioned goal, differ¬ent techniques of analysis of laser processes have been fine-tuned, basing the same in advanced methods for material characterization (like the combined use of EDX Analysis and Confocal Laser Scanning Microscopy) that can be presented as true breakthroughs in the development of specific techniques for characterization in the study of laser processes of selective ablation of materials in thin film technologies, processes that not only have impact in the photovoltaic field, but also in those of microelectronics, biotechnology, micro-fabrication, etc. As an additional outcome, part of the results of this work has been suc¬cessfully applied, by the investigation group to which the author belongs, to the development of processes of enormous interest within other photo¬voltaic technologies, such as the standard technologies on amorphous silicon over glass in superstrate configuration or the processing of thin layers in conventional technologies using crystalline silicon. Lastly, it is important to mention that this work has been possible thanks to the close cooperation between the Centro L´aser of the UPM, in which the author develops her work, and the Grupo de Silicio Depositado of Centro de Investigaciones Energ´eticas, Medioambientales y Tecnol´ogicas, CIEMAT, which, along with the Grupo de Energ´ıa Fotovoltaica of Univer¬sidad de Barcelona, has prepared the largest part of the samples utilized in this study. Such collaborations have been carried out in the context of several projects of applied investigation with public funding, like Proyecto Singular Estrat´egico PSE-MICROSIL08 (PSE-120000-2006-6), Proyecto IN-NDISOL (IPT-420000-2010-6), both funded by the European Regional De¬velopment Fund (ERDF), ”Una manera de hacer Europa” and MICINN, and the projects of Plan Nacional AMIC (ENE2010-21384-C04-02) and ´ CLASICO (ENE2007-6772-C04-04), whose funds have enabled the devel-opment of large part of this work.

Acoustic characterisation of cinema screens

As a consequence of cinema screens being placed in front of screen-speakers, a reduction in sound quality has been noticed. Cinema screens not only let the sound go through them, but also absorb a small amount of it and reflect the sound which impacts on the screen to the back, coming forward again in case it impacts on the loudspeaker. This backwards reflection in addition to the signal coming from the loudspeaker can lead to constructive or destructive interference at certain frequencies which usually results in comb filtering. In this project, this effect has been studied through researching amongst various data sheet provided by different manufacturers, acoustical measurements completed in the large anechoic chamber of the ISVR and some theoretical models developed with MatLab software. If results obtained with MatLab are accurate enough in comparison to the real measurements taken in the anechoic chamber this would lead to a good way to predict which would be the attenuation added to the system at each frequency, given that not all manufacturers provide an attenuation curve, but only an average attenuation. This average attenuation might be useless as sound waves have different wavelengths and its propagation through partitions varies. In fact, sound is composed by high and low frequencies, where high frequencies are characterised by a small wavelength which is usually easier to attenuate than low frequencies that characterised by bigger wavelengths. Furthermore, this information would be of great value to both screen manufacturers, who could offer a much more precise data in their data sheets; and customers, who would have a great amount of information to their disposal before purchasing and installing anything in their cinemas, being able to know by themselves which screen or loudspeaker should be best to meet their expectative. RESUMEN. La aparición de la digitalización de las bandas sonoras para las películas hace posible la mejora en la calidad de sonido de los cines. Sin embargo, un aspecto a tener en cuenta en esta calidad del sonido es la transmisión de éste a través de la pantalla, ya que normalmente tras ella se encuentran situados los altavoces. Las propiedades acústicas varían dependiendo del tipo de pantalla que se utilice, además de haber poca información a la que acceder para poder valorar su comportamiento. A lo largo de este proyecto, se analizan tres muestras de pantallas distintas donadas por distintos fabricantes para poder llegar a la conclusión de dependiendo del tipo de pantalla cuál es la distancia óptima a la que localizar la pantalla respecto al altavoz y con qué inclinación. Dicho análisis se realizó en la cámara anecoica del ISVR (University of Southampton) mediante la construcción de un marco de madera de 2x2 m en el que tensar las pantallas de cine, y un altavoz cuyo comportamiento sea el más similar al de los altavoces de pantalla reales. Los datos se captaron mediante cuatro micrófonos colocados en posiciones distintas y conectados al software Pulse de Brüel & Kjær, a través del cual se obtuvieron las respuestas en frecuencia del altavoz sin pantalla y con ella a diferentes distancias del altavoz. Posteriormente, los datos se analizaron con MatLab donde se calculó la atenuación, el factor de transmisión de la presión (PTF) y el análisis cepstrum. Finalmente, se realizó un modelo teórico del comportamiento de las pantallas perforadas basado en las placas perforadas utilizadas para atenuar el sonido entre distintas habitaciones. Como conclusión se llegó a que las pantallas curvadas son acústicamente más transparentes que las pantallas perforadas que a partir de 6 kHz son más acústicamente opacas. En las pantallas perforadas la atenuación depende del número de perforaciones por unidad de área y el diámetro de éstas. Dicha atenuación se reducirá si se reduce el diámetro de las perforaciones de la pantalla, o si se incrementa la cantidad de perforaciones. Acerca del efecto filtro peine, para obtener la mínima amplitud de éste la pantalla se deberá situar a una distancia entre 15 y 30 cm del altavoz, encontrando a la distancia de 30 cm que la última reflexión analizada a través de Cepstrum llega 5 ms más tarde que la señal directa, por lo cual no debería dañar el sonido ni la claridad del habla.

Laser pulse shaping with liquid crystals

A method of unpolarized laser pulses shaping is reported. The basis of the method is the use of an hybrid optical bistable device with nematic liquid-crystals, similar to the one previously reported by us. A sample of the input light constrols, by an asymmetrical electronic comparator, a 1 x 2 electro-optical total switch. The output pulses are reshaped and maintain the same polarization properties as the input light. From triangular input light signals, symmetriacl and asymmetrical output pulses have been obtained. The minimum pulse width achieved was 0.1 msec. A representation of the output versus input light signals gives an hysteresys cycle in the asymmetrical case.

Laser pulse shaping with liquid crystals (1982)

In this paper we report a new method of laser pulse shaping by the use of liquid crystals as non linear materials. The basis of this method is similar to the one reported by us for an hybrid optical bistable device, but with a different electronic circuitry and feedback.