Relationship among slurry characteristics and gaseous emissions at different types of commercial Spanish pig farms

This study aimed to analyse several factors of variation of slurry composition and to establish prediction equations for potential methane (CH4) and ammonia (NH3) emissions. Seventy-nine feed and slurry samples were collected at two seasons (summer and winter) from commercial pig farms sited at two Spanish regions (Centre and Mediterranean). Nursery, growing-fattening, gestating and lactating facilities were sampled. Feed and slurry composition were determined, and potential CH4 and NH3 emissions measured at laboratory. Feed nutrient contents were used as covariates in the analysis. Near infrared reflectance spectroscopy (NIRS) was evaluated as a predicting tool for slurry composition and potential gaseous emissions. A wide variability was found both in feed and slurry composition. Mediterranean farms had a higher pH (p<0.001) and ash (p=0.02) concentration than those located at the Centre of Spain. Also, type of farm affected ether extract content of the slurry (p=0.02), with highest values obtained for the youngest animal facilities. Results suggested a buffer effect of dietary fibre on slurry pH and a direct relationship (p<0.05) with fibre constituents of manure. Dietary protein content did not affect slurry nitrogen content but decreased (p=0.003) total and volatile solids concentration. Prediction models of potential NH3 emissions (R2=0.89) and CH4 yield (R2=0.61) were obtained from slurry composition. Predictions from NIRS showed a high accuracy for most slurry constituents (R2>0.90) and similar accuracy of prediction of potential NH3 and CH4 emissions (R2=0.84 and 0.68, respectively) to models using slurry characteristics, which can be of interest to estimate emissions from commercial farms and establish mitigation strategies or optimize biogas production.

Effects of nutrition on digestión efficicency and gaseous emissions from slurry in growing-finishing pigs. I. Influence of the inclusión of two levels of orange pulp and carb meal in isofibrous diets

An experiment was conducted to investigate the effects of increasing the level of two sources of fibrous by-products, orange pulp (OP) and carob meal (CM), in iso-NDF growing-finishing pig diets on nutrient balance, slurry composition and potential ammonia (NH3) and methane (CH4) emissions. Thirty pigs (85.4 ± 12.3 kg) were fed five iso-nutritive diets: a commercial control wheat/barley (C) and four experimental diets including two sources of fibrous by-products (OP and CM) and two dietary levels (75 and 150 g/kg) in a 2 × 2 factorial arrangement. After a 14-day adaptation period, faeces and urine were collected separately for 7 days to measure nutrient digestibility and the excretory patterns of N from pigs (6 replicates per diet) housed individually in metabolic pens. For each animal, the derived NH3 and CH4 emissions were measured in samples of slurry over an 11- and 100-day storage periods, respectively. Source and level of the fibrous by-products affected digestion efficiency in a different way as the coefficients of total tract apparent digestibility (CTTAD) for dry matter (DM), organic matter (OM), fibre fractions and gross energy increased with OP but decreased with CM (P < 0.05). Crude protein CTTAD decreased with the inclusion of both sources of fibre, being lower at the highest dietary level. Faecal concentration of fibre fractions increased (P < 0.05) with the level of inclusion of CM but decreased with that of OP (P < 0.01). High dietary level for both sources of fibre increased (P < 0.02) CP faecal content but urine N content decreased (from 205 to 168 g/kg DM, P < 0.05) in all the fibre-supplemented compared to C diet. Additionally, the proportions of undigested dietary, water soluble, and bacterial and endogenous debris of faecal N excretion were not affected by treatments. The initial slurry characteristics did not differ among different fibre sources and dietary levels, except pH, which decreased at the highest by-product inclusion levels. Ammonia emission per kg of slurry was lower in all the fibre-supplemented diets than in C diet (from 2.44 to 1.81 g, P < 0.05). Additionally, slurries from the highest dietary level of by-products tended (P < 0.06) to emit less NH3 per kg of initial total Kjeldahl N and showed a lower B0, independently of the fibre source. Thus, the fibre sources and their dietary levels affected pig nutrient digestion and composition of urine and faeces, showing potential to decrease NH3 and CH4 emissions at high levels of inclusion, independently of type of fibre.

Effects of nutrition on digestión efficiency and gaseous emissions from slurry in growing pigs: III. Influence of varying the dietary level of calcium soap of palm fatty acids distillate with or without orange pulp supplemention

The aim of this study was to establish the relationships between faecal fat concentration and gaseous emissions from pig slurry. Five diets were designed to meet essential nutrient requirements: a control and four experimental feeds including two levels (35 or 70 g/kg) of calcium soap fatty acids distillate (CSP) and 0 or 200 g/kg of orange pulp (OP) combined in a 2 × 2 factorial structure. Thirty growing pigs (six per treatment) were used to measure dry matter (DM) and N balance, coefficients of total tract apparent digestibility (CTTAD) of nutrients, faecal and urine composition and potential emissions of ammonia (NH3) and methane (CH4). Increasing dietary CSP level decreased DM, ether extract (EE) and crude protein (CP) CTTAD (by 4.0, 11.1 and 3.5%, respectively, P < 0.05), but did not influence those of fibrous constituents. It also led to a decrease (from 475 to 412 g/kg DM, P < 0.001) of faecal concentration of neutral detergent fibre (aNDFom) and to an increment (from 138 to 204 g/kg, P < 0.001) of EE in faecal DM that was related to greater CH4 emissions, both per gram of organic matter (P = 0.021) or on a daily basis (P < 0.001). Level of CSP did not affect N content in faeces or urine, but increased daily DM (P < 0.001), and N (P = 0.031) faecal excretion with no effect on urine N excretion. This resulted in lesser (P = 0.036) NH3 potential emission per kg of slurry. Addition of OP decreased CTTAD of EE (by 7.9%, P = 0.044), but increased (P < 0.05) that of all the fibrous fractions. As a consequence, faecal EE content increased (from 165 to 177 g/kg DM; P = 0.012), and aNDFom decreased greatly (from 483 to 404 g/kg DM, P < 0.001), which in all resulted in a lack of effect of OP on CH4 potential emission. Inclusion of OP in the diet also led to a significant decrease of CP CTTAD (by 6.85%, P < 0.001), and to an increase of faecal CP concentration (from 174 to 226 g/kg DM, P < 0.001), with no significant influence on urine N content. These effects resulted in higher N faecal losses, especially those of the undigested dietary origin, without significant effects on potential NH3 emission. No significant interactions between CSP and OP supplementation were observed for the gaseous emissions measured.

Effects of nutrition on digestión efficicency and gaseous emissions from slurry in growing-finishing pigs. II. Effect of protein source in practical diets.

Uso de diferentes fuentes de proteína en la alimentación de cerdos en fase de cebo y su relación con las emisiones de gases amoniaco y metano.

Ammonia and methane gas emissions from pig slurry: variability induced through feeding strategies

Esta Tesis doctoral fue desarrollada para estudiar las emisiones de amoniaco (NH3) y metano (CH4) en purines de cerdos, y los efectos ocasionados por cambios en la formulación de la dieta. Con este propósito, fueron llevados a cabo tres estudios. El experimento 1 fue realizado con el objetivo de analizar los factores de variación de la composición de purines y establecer ecuaciones de predicción para emisiones potenciales de NH3 y CH4. Fueron recogidas setenta y nueve muestras de piensos y purines durante dos estaciones del año (verano y invierno) de granjas comerciales situadas en dos regiones de España (Centro y Mediterráneo). Se muestrearon granjas de gestación, maternidad, lactación y cebo. Se determinó la composición de piensos y purines, y la emisión potencial de NH3 y CH4. El contenido de nutrientes de los piensos fue usado como covariable en el análisis. La espectroscopia de reflectancia del infrarrojo cercano (NIRS) se evaluó como herramienta de predicción de la composición y potencial emisión de gases del purín. Se encontró una amplia variabilidad en la composición de piensos y purines. Las granjas del Mediterráneo tenían mayor pH (P<0,001) y concentración de cenizas (P =0,02) en el purín que las del Centro. El tipo de granja también afectó al contenido de extracto etéreo (EE) del purín (P =0,02), observando los valores más elevados en las instalaciones de animales jóvenes. Los resultados sugieren un efecto tampón de la fibra de la dieta en el pH del purín y una relación directa (P<0,05) con el contenido de fibra fecal. El contenido de proteína del pienso no afectó al contenido de nitrógeno del purín, pero disminuyó (P=0,003) la concentración de sólidos totales (ST) y de sólidos volátiles (SV). Se obtuvieron modelos de predicción de la emisión potencial de NH3 (R2=0,89) y CH4 (R2=0,61) partir de la composición del purín. Los espectros NIRS mostraron una buena precisión para la estimación de la mayor parte de los constituyentes, con coeficientes de determinación de validación cruzada (R2cv) superiores a 0,90, así como para la predicción del potencial de emisiones de NH3 y CH4 (R2cv=0,84 y 0,68, respectivamente). El experimento 2 fue realizado para investigar los efectos del nivel de inclusión de dos fuentes de sub-productos fibrosos: pulpa de naranja (PN) y pulpa de algarroba (PA), en dietas iso-fibrosas de cerdos de cebo, sobre la composición del purín y las emisiones potenciales de NH3 y CH4. Treinta cerdos (85,4±12,3 kg) fueron alimentados con cinco dietas iso-nutritivas: control comercial trigo/cebada (C) y cuatro dietas experimentales incluyendo las dos fuentes de sub-productos a dos niveles (75 y 150 g/kg) en una estructura 2 × 2 factorial. Después de 14 días de periodo de adaptación, heces y orina fueron recogidas separadamente durante 7 días para medir la digestibilidad de los nutrientes y el nitrógeno (N) excretado (6 réplicas por dieta) en cerdos alojados individualmente en jaulas metabólicas. Las emisiones de NH3 y CH4 fueron medidas después de la recogida de los purínes durante 11 y 100 días respectivamente. La fuente y el nivel de subproductos fibrosos afectó a la eficiencia digestiva de diferentes formas, ya que los coeficientes de digestibilidad total aparente (CDTA) para la materia seca (MS), materia orgánica (MO), fracciones fibrosas y energía bruta (EB) aumentaron con la PN pero disminuyeron con la inclusión de PA (P<0,05). El CDTA de proteína bruta (PB) disminuyó con la inclusión de las dos fuentes de fibra, siendo más bajo al mayor nivel de inclusión. La concentración fecal de fracciones fibrosas aumentó (P<0,05) con el nivel de inclusión de PA pero disminuyó con el de PN (P<0,01). El nivel más alto de las dos fuentes de fibra en el pienso aumentó (P<0,02) el contenido de PB fecal pero disminuyó el contenido de N de la orina (de 205 para 168 g/kg MS, P<0,05) en todas las dietas suplementadas comparadas con la dieta C. Adicionalmente, las proporciones de nitrógeno indigerido, nitrógeno soluble en agua, nitrógeno bacteriano y endógeno excretado en heces no fueron afectados por los tratamientos. Las características iniciales del purín no difirieron entre las diferentes fuentes y niveles de fibra, excepto para el pH que disminuyó con la inclusión de altos niveles de sub-productos. La emisión de NH3 por kg de purín fue más baja en todas las dietas suplementadas con fibras que en la dieta C (2,44 vs.1,81g de promedio, P<0,05). Además, purines de dietas suplementadas con alto nivel de sub-productos tendieron (P<0,06) a emitir menos NH3 por kg de nitrógeno total y mostraron un potencial más bajo para emitir CH4, independientemente de la fuente de fibra. El experimento 3 investigó los efectos de la fuente de proteína en dietas prácticas. Tres piensos experimentales fueron diseñados para sustituir una mescla de harina y cascarilla de soja (SOJ) por harina de girasol (GIR) o por DDGS del trigo (DDGST). La proporción de otros ingredientes fue modificada para mantener los contenidos de nutrientes similares a través de las dietas. El cambio en la fuente de proteína dio lugar a diferencias en el contenido de fibra neutro detergente ligada a proteína bruta (FNDPB), fibra soluble (FS) y lignina ácido detergente (LAD) en la dieta. Veinticuatro cerdos (ocho por dieta), con 52,3 o 60,8 kg en la primera y segunda tanda respectivamente, fueron alojados individualmente en jaulas metabólicas. Durante un periodo de 7 días fue determinado el balance de MS, el CDTA de los nutrientes y la composición de heces y orina. Se realizó el mismo procedimiento del experimento 2 para medir las emisiones de NH3 y CH4 de los purines de cada animal. Ni la ingestión de MS ni el CDTA de la MS o de la energía fueron diferentes entre las dietas experimentales, pero el tipo de pienso afectó (P<0.001) la digestibilidad de la PB, que fue mayor para GIR (0,846) que para SOJ (0,775), mientras que la dieta DDGST mostró un valor intermedio (0,794). La concentración fecal de PB fue por tanto influenciada (P<0,001) por el tratamiento, observándose la menor concentración de PB en la dieta GIR y la mayor en la dieta SOJ. La proporción de N excretado en orina o heces disminuyó de 1,63 en la dieta GIR hasta 0,650 en la dieta SOJ, como consecuencia de perdidas más bajas en orina y más altas en heces, con todas las fracciones de nitrógeno fecales creciendo en paralelo a la excreción total. Este resultado fue paralelo a una disminución de la emisión potencial de NH3 (g/kg purín) en la dieta SOJ con respecto a la dieta GIR (desde 1,82 a 1,12, P<0,05), dando valores intermedios (1,58) para los purines de la dieta DDGST. Por otro lado, el CDTA de la FS y de la fibra neutro detergente (FND) fueron afectados (P<0,001 y 0,002, respectivamente) por el tipo de dieta, siendo más bajas en la dieta GIR que en la dieta SOJ; además, se observó un contenido más alto de FND (491 vs. 361g/kg) en la MS fecal para la dieta GIR que en la dieta SOJ, presentando la dieta DDGST valores intermedios. El grado de lignificación de la FND (FAD/FND x 100) de las heces disminuyó en el orden GIR>DDGST>SOJ (desde 0,171 hasta 0,109 y 0,086, respectivamente) en paralelo a la disminución del potencial de emisión de CH4 por g de SV del purín (desde 301 a 269 y 256 mL, respectivamente). Todos los purines obtenidos en estos tres experimentos y Antezana et al. (2015) fueron usados para desarrollar nuevas calibraciones con la tecnología NIRS, para predecir la composición del purín y el potencial de las emisiones de gases. Se observó una buena precisión (R2cv superior a 0,92) de las calibraciones cuando muestras de los ensayos controlados (2, 3 y Antezana et al., 2015) fueron añadidas, aumentando el rango de variación. Una menor exactitud fue observada para TAN y emisiones de NH3 y CH4, lo que podría explicarse por una menor homogeneidad en la distribución de las muestras cuando se amplía el rango de variación del estudio. ABSTRACT This PhD thesis was developed to study the emissions of ammonia (NH3) and methane (CH4) from pig slurry and the effects caused by changes on diet formulation. For these proposes three studies were conducted. Experiment 1 aimed to analyse several factors of variation of slurry composition and to establish prediction equations for potential CH4 and NH3 emissions. Seventy-nine feed and slurry samples were collected at two seasons (summer and winter) from commercial pig farms sited at two Spanish regions (Centre and Mediterranean). Nursery, growing-fattening, gestating and lactating facilities were sampled. Feed and slurry composition were determined, and potential CH4 and NH3 emissions measured. Feed nutrient contents were used as covariates in the analysis. Near infrared reflectance spectroscopy (NIRS) was evaluated as a predicting tool for slurry composition and potential gaseous emissions. A wide variability was found both in feed and slurry composition. Mediterranean farms had a higher pH (P<0.001) and ash (P=0.02) concentration than those located at the centre of Spain. Also, type of farm affected ether extract (EE) content of the slurry (P=0.02), with highest values obtained for the youngest animal facilities. Results suggested a buffer effect of dietary fibre on slurry pH and a direct relationship (P<0.05) with fibre constituents of manure. Dietary protein content did not affect slurry nitrogen content (N) but decreased (P=0.003) in total solid (TS) and volatile solids (VS) concentration. Prediction models of potential NH3 emissions (R2=0.89) and biochemical CH4 potential (B0) (R2=0.61) were obtained from slurry composition. Predictions from NIRS showed a high accuracy for most slurry constituents with coefficient of determination of cross validation (R2cv) above 0.90 and a similar accuracy of prediction of potential NH3 and CH4 emissions (R2cv=0.84 and 0.68, respectively) thus models based on slurry composition from commercial farms. Experiment 2 was conducted to investigate the effects of increasing the level of two sources of fibrous by-products, orange pulp (OP) and carob meal (CM), in iso-fibrous diets for growing-finishing pig, slurry composition and potential NH3 and CH4 emissions. Thirty pigs (85.4±12.3 kg) were fed five iso-nutritive diets: a commercial control wheat/barley (C) and four experimental diets including two sources of fibrous by-products OP and CM and two dietary levels (75 and 150 g/kg) in a 2 × 2 factorial arrangement. After a 14-day adaptation period, faeces and urine were collected separately for 7 days to measure nutrient digestibility and the excretory patterns of N from pigs (6 replicates per diet) housed individually in metabolic pens. For each animal, the derived NH3 and CH4 emissions were measured in samples of slurry over an 11 and 100-day storage periods, respectively. Source and level of the fibrous by-products affected digestion efficiency in a different way as the coefficients of total tract apparent digestibility (CTTAD) for dry matter (DM), organic matter (OM), fibre fractions and gross energy (GE) increased with OP but decreased with CM (P<0.05). Crude protein CTTAD decreased with the inclusion of both sources of fibre, being lower at the highest dietary level. Faecal concentration of fibre fractions increased (P<0.05) with the level of inclusion of CM but decreased with that of OP (P<0.01). High dietary level for both sources of fibre increased (P<0.02) CP faecal content but urine N content decreased (from 205 to 168 g/kg DM, P<0.05) in all the fibre-supplemented compared to C diet. Additionally, the proportions of undigested dietary, water soluble, and bacterial and endogenous debris of faecal N excretion were not affected by treatments. The initial slurry characteristics did not differ among different fibre sources and dietary levels, except pH, which decreased at the highest by-product inclusion levels. Ammonia emission per kg of slurry was lower in all the fibre-supplemented diets than in C diet (2.44 vs. 1.81g as average, P<0.05). Additionally, slurries from the highest dietary level of by-products tended (P<0.06) to emit less NH3 per kg of initial total Kjeldahl nitrogen (TKN) and showed a lower biochemical CH4 potential , independently of the fibre source. Experiment 3 investigated the effects of protein source in practical diets. Three experimental feeds were designed to substitute a mixture of soybean meal and soybean hulls (SB diet) with sunflower meal (SFM) or wheat DDGS (WDDGS). The proportion of other ingredients was also modified in order to maintain similar nutrient contents across diets. Changes in protein source led to differences in dietary content of neutral detergent insoluble crude protein (NDICP), soluble fibre (SF) and acid detergent lignin (ADL). Twenty-four pigs (eight per diet), weighing 52.3 or 60.8 kg at the first and second batch respectively, were housed individually in metabolic pens to determine during a 7-day period DM balance, CTTAD of nutrients, and faecal and urine composition. Representative slurry samples from each animal were used to measure NH3 and CH4 emissions over an 11 and or 100-day storage period, respectively. Neither DM intake, nor DM or energy CTTAD differed among experimental diets, but type of feed affected (P<0.001) CP digestibility, which was highest for SFM (0.846) than for SB (0.775) diet, with WDDGS-based diet giving an intermediate value (0.794). Faecal DM composition was influenced (P<0.001) accordingly, with the lowest CP concentration found for diet SFM and the highest for SB. The ratio of N excreted in urine or faeces decreased from SFM (1.63) to SB diet (0.650), as a consequence of both lower urine and higher faecal losses, with all the faecal N fractions increasing in parallel to total excretion. This result was parallel to a decrease of potential NH3 emission (g/kg slurry) in diet SB with respect to diet SFM (from 1.82 to 1.12, P<0.05), giving slurry from WDDGS-based diet an intermediate value (1.58). Otherwise, SF and insoluble neutral detergent fibre (NDF) CTTAD were affected (P<0.001 and P=0.002, respectively) by type of diet, being lower for SFM than in SB-diet; besides, a higher content of NDF (491 vs. 361 g/kg) in faecal DM was observed for SFM with respect to SB based diet, with WDDGS diet being intermediate. Degree of lignification of NDF (ADL/NDF x 100) of faeces decreased in the order SFM>WDDGS>SB (from 0.171 to 0.109 and 0.086, respectively) in parallel to a decrease of biochemical CH4 potential per g of VS of slurry (from 301 to 269 and 256 ml, respectively). All slurry samples obtained from these three experiments and Antezana et al. (2015) were used to develop new calibrations with NIRS technology, to predict the slurry composition and potential gaseous emissions of samples with greater variability in comparison to experiment 1. Better accuracy (R2cv above 0.92) was observed for calibrations when samples from controlled trials experiments (2, 3 and Antezana et al., 2015) were included, increasing the range of variation. A lower accuracy was observed for TAN, NH3 and CH4 gaseous emissions, which might be explained by the less homogeneous distribution with a wider range of data.

Composition, potential emissions and agricultural value of pig slurry from Spanish commercial farms

Pig slurry is a valuable fertilizer for crop production but at the same time its management may pose environmental risks. Slurry samples were collected from 77 commercial farms of four animal categories (gestating and lactating sows, nursery piglets and growing pigs) and analyzed for macronutrients, micronutrients, heavy metals and volatile fatty acids. Emissions of ammonia (NH3) and biochemical methane potential (BMP) were quantified. Slurry electrical conductivity, pH, dry matter content and ash content were also determined. Data analysis included an analysis of correlations among variables, the development of prediction models for gaseous emissions and the analysis of nutritional content of slurries for crop production. Descriptive information is provided in this work and shows a wide range of variability in all studied variables. Animal category affected some physicochemical parameters, probably as a consequence of different slurry management and use of cleaning water. Slurries from gestating sows and growing pigs tended to be more concentrated in nutrients, whereas the slurry from lactating sows and nursery piglets tended to be more diluted. Relevant relationships were found among slurry characteristics expressed in fresh basis and gas emissions. Predictive models using on-farm measurable parameters were obtained for NH3 (R2 = 0.51) and CH4

Evaluation of the influence of toll systems on energy consumption and CO2 emissions: A case study of a Spanish highway

This paper studies the energy consumption and subsequent CO2 emissions of road highway transportation under three toll systems in Spain for four categories of vehicles: cars, vans, buses and articulated trucks. The influence of toll systems is tested for a section of AP-41 highway between Toledo and Madrid. One system is free flow, other is traditional stop and go and the last toll system operates with an electronic toll collection (ETC) technology. Energy consumption and CO2 emissions were found to be closely related to vehicle mass, wind exposure, engine efficiency and acceleration rate. These parameters affect, directly or indirectly, the external forces which determine the energy consumption. Reducing the magnitude of these forces through an appropriate toll management is an important way of improving the energy performance of vehicles. The type of toll system used can have a major influence on the energy efficiency of highway transportation and therefore it is necessary to consider free flow.

Environmental analysis of residential building facades through energy consumption, GHG emissions and costs

This paper provides some results on the potential to minimize environmental impacts in residential buildings life cycle, through façade design strategies, analyzing also their impact on costs from a lifecycle perspective. On one hand, it assesses the environmental damage produced by the materials of the building envelope, and on the other, the benefits they offer in terms of habitability and liveability in the use phase. The analysis includes several design parameters used both for rehabilitation of existing facades, as for new facades, trying to cover various determinants and proposing project alternatives. With this study we intended to contribute to address the energy challenges for the coming years, trying also to propose pathways for innovative solutions for the building envelope.

Influence of driving style on fuel consumption and Emissions in diesel-powered passenger car

This paper presents the main results of a study on the influence of driving style on fuel consumption and pollutant emissions of diesel passenger car in urban traffic. Driving styles (eco, normal or aggressive) patterns were based on the “eco-driving” criteria. The methodology is based on on-board emission measurements in real urban traffic in the city of Madrid. Five diesel passenger cars, have been tested. Through a statistical analysis, a Dynamic Performance Index was defined for diesel passenger cars. Likewise, the CO, NOX and HC emissions were compared for each driving style for the tested vehicles. Eco-driving reduces by 14% fuel consumption and CO2 emissions, but aggressive driving increase consumption by 40%. Aggressive driving increases NOX emission by more than 40%. CO and HC, show different trends, but being increased in eco-driving style.

Proposal of a dynamic performance index to analyze driving pattern effect on car emissions

The contributions of driver behaviour as well as surrounding infrastructure are decisive on pollutant emissions from vehicles in real traffic situations. This article deals with the preliminary study of the interaction between the dynamic variables recorded in a vehicle (driving pattern) and pollutant emissions produced over a given urban route. It has been established a “dynamic performance index”-DPI, which is calculated from some driving pattern parameters, which in turn depends on traffic congestion level and route characteristics, in order to determine whether the driving has been aggressive, normal or calm. Two passenger cars instrumented with a portable activity measurement system -to record dynamic variables- and on-board emission measurement equipment have been used. This study has shown that smooth driving patterns can reduce up to 80% NOX emissions and up to 20% of fuel in the same route

Quantity of CO2 Emissions in the Life Cycle of a Highway Infrastructure

There is strong evidence to indicate that carbon dioxide and other greenhouse gases are accumulating at unprecedented concentrations in out atmosphere contributing to global climate change. Evidence is equally strong that human activities, mainly the burning of fossil fuels, are driving force in this process (IPCC 2007). While different industries contribute varying amounts to total anthropogenic greenhouse gases, it is incumbent upon each to understand its contribution and search for sensible ways to reduce overall greenhouse gas production. The aim of this paper is the development of a methodology to determine the amount of CO2 emissions of a highway, allowing providing solutions that can improve the energy footprint and reduce its emissions

Emissions and economic costs of cycling compact fluorescent lamps with integrated ballasts

This paper proposes a way to quantify the emissions of mercury (Hg) and CO2 associated with the manufacture and operation of compact fluorescent lamps with integrated ballasts (CFLis), as well as the economic cost of using them under different operating cycles. The main purpose of this paper is to find simple criteria for reducing the polluting emissions under consideration and the economic cost of CFLi to a minimum. A lifetime model is proposed that allows the emissions and costs to be described as a function of degradation from turning CFLi on and their continuous operation. An idealized model of a CFLi is defined that combines characteristics stated by different manufacturers. In addition, two CFLi models representing poor-quality products are analyzed. It was found that the emissions and costs per unit of time of operation of the CFLi depend linearly on the number of times per unit of time it is turned on and the time of continuous operation. The optimal conditions (lowest emissions and costs) depend on the place of manufacture, the place of operation and the quality of the components of the lamp/ballast. Finally, it was also found that for each lamp, there are intervals when it is turned off during which emissions of pollutants and costs are identical regardless of how often the lamp is turned on or the time it remains on. For CO2 emissions, the lamp must be off up to 5 minutes; for the cost, up to 7 minutes and for Hg emissions, up to 43 minutes. It is advisable not to turn on a CFLi sooner than 43 minutes from the last time it was turned off.

Influence of the composition of natural gas-hydrogen blends (HCNG) on performance an CO2 emissions of a spark ignition engine

Addition of hydrogen to natural gas could be a short-term alternative to nowadays fossil fuels as the emissions of greenhouse gases may be reduced. The aim of this study is to evaluate the performance and emissions of a park ignition engine fuelled with pure natural gas, pure hydrogen and different blends of hydrogen and natural gas (HCNG). The increase of the hydrogen fraction leads to variations in the cylinder pressure and CO2 emissions. In this work, a combustion model based on thermodynamic equations is used considering separated zones for the burned and unburned gases. The results show that the maximum cylinder pressure gets higher as the fraction of hydrogen in the blend increases. The presence of hydrogen in the blend leads to a drecrease in the CO2 emissions. Due to hydrogen properties, leaner fuel-air mixtures can be used along with the appropiate spark timing, leading to an engine emissions improvement without a performance worsening.

Development of a methodology and tool to evaluate the impact of ICT measures on road transport emissions

The paper presents the main elements of a project entitled ICT-Emissions that aims at developing a novel methodology to evaluate the impact of ICT-related measures on mobility, vehicle energy consumption and CO2 emissions of vehicle fleets at the local scale, in order to promote the wider application of the most appropriate ICT measures. The proposed methodology combines traffic and emission modelling at micro and macro scales. These will be linked with interfaces and submodules which will be specifically designed and developed. A number of sources are available to the consortium to obtain the necessary input data. Also, experimental campaigns are offered to fill in gaps of information in traffic and emission patterns. The application of the methodology will be demonstrated using commercially available software. However, the methodology is developed in such a way as to enable its implementation by a variety of emission and traffic models. Particular emphasis is given to (a) the correct estimation of driver behaviour, as a result of traffic-related ICT measures, (b) the coverage of a large number of current vehicle technologies, including ICT systems, and (c) near future technologies such as hybrid, plug-in hybrids, and electric vehicles. The innovative combination of traffic, driver, and emission models produces a versatile toolbox that can simulate the impact on energy and CO2 of infrastructure measures (traffic management, dynamic traffic signs, etc.), driver assistance systems and ecosolutions (speed/cruise control, start/stop systems, etc.) or a combination of measures (cooperative systems).The methodology is validated by application in the Turin area and its capacity is further demonstrated by application in real world conditions in Madrid and Rome.

Energy consumption and carbon dioxide emissions in rail and road freight transport in Spain: a case study of car carriers and bulk petrochemicals

This article provides a new methodology for estimating fuel consumption and emissions by enabling a correct comparison between freight transportation modes. The approach is developed and integrated as a part of an intelligent transportation system dealing with goods movement. A key issue is related to energy consumption ratios and consequent CO2 emissions. Energy consumption ratios are often used based on transport demand. However, including other ratios based on transport supply can be useful. Furthermore, it is important to indicate which factors are associated with variations in energy consumption and emissions; especially of interest are parameters that have a higher incidence and order of magnitude, in order to fairly compare and understand the difference between transport modes and sub-modes. The study finds that the use of an energy consumption equation can improve the quality of the estimates. The study proposes that coefficients that define the energy consumption equation should be tested to determine market niches and sources of improvement in energy consumption according to the category of vehicles, fuel types used, and classes of products transported.