Development of a novel autonomous robot for navigation and inspect in oil wells

This paper proposes a novel robotic system that is able to move along the outside of the oil pipelines used in Electric Submersible Pumps (ESP) and Progressive Cavity Pumps (PCP) applications. This novel design, called RETOV, proposes a light weight structure robot that can be equipped with sensors to measure environmental variables avoiding damage in pumps and wells. In this paper, the main considerations and methodology of design and implementation are discussed. Finally, the first experimental results that show RETOV moving in vertical pipelines are analyzed.

Dynamics of thermal ignition of spray flames in mixing layers

Conditions are identified under which analyses of laminar mixing layers can shed light on aspects of turbulent spray combustion. With this in mind, laminar spray-combustion models are formulated for both non-premixed and partially premixed systems. The laminar mixing layer separating a hot-air stream from a monodisperse spray carried by either an inert gas or air is investigated numerically and analytically in an effort to increase understanding of the ignition process leading to stabilization of high-speed spray combustion. The problem is formulated in an Eulerian framework, with the conservation equations written in the boundary-layer approximation and with a one-step Arrhenius model adopted for the chemistry description. The numerical integrations unveil two different types of ignition behaviour depending on the fuel availability in the reaction kernel, which in turn depends on the rates of droplet vaporization and fuel-vapour diffusion. When sufficient fuel is available near the hot boundary, as occurs when the thermochemical properties of heptane are employed for the fuel in the integrations, combustion is established through a precipitous temperature increase at a well-defined thermal-runaway location, a phenomenon that is amenable to a theoretical analysis based on activation-energy asymptotics, presented here, following earlier ideas developed in describing unsteady gaseous ignition in mixing layers. By way of contrast, when the amount of fuel vapour reaching the hot boundary is small, as is observed in the computations employing the thermochemical properties of methanol, the incipient chemical reaction gives rise to a slowly developing lean deflagration that consumes the available fuel as it propagates across the mixing layer towards the spray. The flame structure that develops downstream from the ignition point depends on the fuel considered and also on the spray carrier gas, with fuel sprays carried by air displaying either a lean deflagration bounding a region of distributed reaction or a distinct double-flame structure with a rich premixed flame on the spray side and a diffusion flame on the air side. Results are calculated for the distributions of mixture fraction and scalar dissipation rate across the mixing layer that reveal complexities that serve to identify differences between spray-flamelet and gaseous-flamelet problems.

Characteristics of the turbulent/nonturbulent interface in boundary layers, jets and shear-free turbulence

The characteristics of turbulent/nonturbulent interfaces (TNTI) from boundary layers, jets and shear-free turbulence are compared using direct numerical simulations. The TNTI location is detected by assessing the volume of turbulent flow as function of the vorticity magnitude and is shown to be equivalent to other procedures using a scalar field. Vorticity maps show that the boundary layer contains a larger range of scales at the interface than in jets and shear-free turbulence where the change in vorticity characteristics across the TNTI is much more dramatic. The intermittency parameter shows that the extent of the intermittency region for jets and boundary layers is similar and is much bigger than in shear-free turbulence, and can be used to compute the vorticity threshold defining the TNTI location. The statistics of the vorticity jump across the TNTI exhibit the imprint of a large range of scales, from the Kolmogorov micro-scale to scales much bigger than the Taylor scale. Finally, it is shown that contrary to the classical view, the low-vorticity spots inside the jet are statistically similar to isotropic turbulence, suggesting that engulfing pockets simply do not exist in jets

Soil compaction and vegetation cover in a Scots pine stand at the Mediterranean rangelands

Right development of ROOT SYSTEMS is essential to ensure seedling survival in the initial stages of natural regeneration processes. Soil compaction determines this development both because of its influence on soil Tª & moisture dynamics and for its direct effect on soil mechanical impedance to root growth. All this effects can be assessed as a whole through soil penetration resistance (Soil Strength) measurements. SOIL STRENGTH has been usually evaluated in forest research in connection with severe disturbances derived from heavy machinery works during forest operations. Nevertheless, undisturbed soils are also expected to show different levels of compaction for root development. Organic matter modifies soil structure and so on porosity, compaction and resultant soil resistance to penetration. Its concentration in surface layers is rather related to vegetation cover composition and density. So within forest stands, a relationship is expected to be found between VEGETATION COVER density and compaction measured as resistance to penetration (soil strength)

Summer deficit irrigation strategies in hedgerow olive orchard cv. ‘Arbequina’: Effect on fruit characteristics and yield.

Maximum production in hedgerow olive orchards is likely not achieved with maximum evapotranspiration over the long-term. Thus, regulated deficit irrigation (RDI) should be considered as a management option. Four irrigation treatments were evaluated during the summer when olive is most drought resistant. Control (CON) was irrigated to maintain the rootzone close to field capacity. Severe water deficit was applied by irrigating 30% CON from end of fruit drop to end July (DI-J) and from end July until beginning of oil synthesis (DI-A). Less severe water deficit was applied during July and August (DI-JA) by irrigating 50% CON. Flowering, fruiting, abscission, fruit development, fresh and dry weight of fruits, and oil production were evaluated. There were not significant differences in number of buds initiated, number of fruits per inflorescence and fruit drop. Oil production was significantly different between irrigation treatments in all experimental years. CON produced more oil and fruit with higher oil% than DI-A and DI-JA. Oil production of DI-J was not significantly reduced compared to CON and oil% was greater. DI-J was the most effective RDI strategy; with 16% less applied water relative to CON average loss in oil production of 8% was not significantly different to CON. While DI-JA saved most water (27%), oil production was reduced by 15%. Greatest loss in oil production (21%) was observed in DI-A with water saving of 22%.

Interstitial Ti for intermediate band formation in Ti-supersaturated silicon

We have analyzed by means of Rutherford backscattering spectrometry (RBS) the Ti lattice location and the degree of crystalline lattice recovery in heavily Ti implanted silicon layers subsequently pulsed laser melted (PLM). Theoretical studies have predicted that Ti should occupy interstitial sites in silicon for a metallic-intermediate band (IB) formation. The analysis of Ti lattice location after PLM processes is a crucial point to evaluate the IB formation that can be clarifyied by means of RBS measurements. After PLM, time-of-flight secondary ion mass spectrometry measurements show that the Ti concentration in the layers is well above the theoretical limit for IB formation. RBS measurements have shown a significant improvement of the lattice quality at the highest PLM energy density studied. The RBS channeling spectra reveals clearly that after PLM processes Ti impurities are mostly occupying interstitial lattice sites.

High reynolds numbers turbulent boundary layers

Esta tesis estudia las similitudes y diferencias entre los flujos turbulentos de pared de tipo externo e interno, en régimen incompresible, y a números de Reynolds moderada¬mente altos. Para ello consideramos tanto simulaciones numéricas como experimentos de capas límites con gradiente de presiones nulo y de flujos de canal, ambos a números de Reynolds en el rango δ+ ~ 500 - 2000. Estos flujos de cortadura son objeto de numerosas investigaciones debido a la gran importancia que tienen tanto a nivel tecnológico como a nivel de física fundamental. No obstante, todavía existen muchos interrogantes sobre aspectos básicos tales como la universalidad de los perfiles medios y de fluctuación de las velocidades o de la presión, tanto en la zona cercana a la pared como en la zona logarítmica, el escalado y el efecto del número de Reynolds, o las diferencias entre los flujos internos y externos en la zona exterior. En éste estudio hemos utilizado simulaciones numéricas ya existentes de canales y capas límites a números de Reynolds δ+ ~ 2000 y δ+ ~ 700, respectivamente. Para poder comparar ambos flujos a igual número de Reynolds hemos realizado una nueva simulación directa de capa límite en el rango δ+ ~ 1000-2000. Los resultados de la misma son presentados y analizados en detalle. Los datos sin postprocesar y las estadísticas ya postprocesadas están públicamente disponibles en nuestro sitio web.162 El análisis de las estadísticas usando un único punto confirma la existencia de perfiles logarítmicos para las fluctuaciones de la velocidad transversal w'2+ y de la presión p'2+ en ambos tipos de flujos, pero no para la velocidad normal v'2+ o la velocidad longitudinal u'2+. Para aceptar o rechazar la existencia de un rango logarítmico en u'2+ se requieren números de Reynolds más altos que los considerados en éste trabajo. Una de las conse¬cuencias más importantes de poseer tales perfiles es que el valor máximo de la intensidad, que se alcanza cerca de la pared, depende explícitamente del número de Reynolds. Esto ha sido confirmado tras analizar un gran número de datos experimentales y numéricos, cor¬roborando que el máximo de u'2+, p/2+, y w'2+ aumenta proporcionalmente con el log(δ+). Por otro lado, éste máximo es más intenso en los flujos externos que en los internos. La máxima diferencia ocurre en torno a y/δ ~ 0.3-0.5, siendo esta altura prácticamente independiente del número de Reynolds considerado. Estas diferencias se originan como consecuencia del carácter intermitente de las capas límites, que es inexistente en los flujos internos. La estructura de las fluctuaciones de velocidad y de presión, junto con la de los esfuer¬zos de Reynolds, se han investigado por medio de correlaciones espaciales tridimensionales considerando dos puntos de medida. Hemos obtenido que el tamaño de las mismas es gen¬eralmente mayor en canales que en capas límites, especialmente en el caso de la correlación longitudinal Cuu en la dirección del flujo. Para esta correlación se demuestra que las es¬tructuras débilmente correladas presentan longitudes de hasta 0(75), en el caso de capas límites, y de hasta 0(185) en el caso de canales. Estas longitudes se obtienen respecti-vamente en la zona logarítmica y en la zona exterior. Las longitudes correspondientes en la dirección transversal son significativamente menores en ambos flujos, 0(5 — 25). La organización espacial de las correlaciones es compatible con la de una pareja de rollos casi paralelos con dimensiones que escalan en unidades exteriores. Esta organización se mantiene al menos hasta y ~ 0.65, altura a la cual las capas límites comienzan a organi¬zarse en rollos transversales. Este comportamiento es sin embargo más débil en canales, pudiéndose observar parcialmente a partir de y ~ 0.85. Para estudiar si estas estructuras están onduladas a lo largo de la dirección transver¬sal, hemos calculado las correlaciones condicionadas a eventos intensos de la velocidad transversal w'. Estas correlaciones revelan que la ondulación de la velocidad longitudinal aumenta conforme nos alejamos de la pared, sugiriendo que las estructuras están más alineadas en la zona cercana a la pared que en la zona lejana a ella. El por qué de esta ondulación se encuentra posiblemente en la configuración a lo largo de diagonales que presenta w'. Estas estructuras no sólo están onduladas, sino que también están inclinadas respecto a la pared con ángulos que dependen de la variable considerada, de la altura, y de el contorno de correlación seleccionado. Por encima de la zona tampón e independien¬temente del número de Reynolds y tipo de flujo, Cuu presenta una inclinación máxima de unos 10°, las correlaciones Cvv y Cm son esencialmente verticales, y Cww está inclinada a unos 35°. Summary This thesis studies the similitudes and differences between external and internal in¬compressible wall-bounded turbulent flows at moderately-high Reynolds numbers. We consider numerical and experimental zero-pressure-gradient boundary layers and chan¬nels in the range of δ+ ~ 500 — 2000. These shear flows are subjects of intensive research because of their technological importance and fundamental physical interest. However, there are still open questions regarding basic aspects such as the universality of the mean and fluctuating velocity and pressure profiles at the near-wall and logarithmic regions, their scaling and the effect of the Reynolds numbers, or the differences between internal and external flows at the outer layer, to name but a few. For this study, we made use of available direct numerical simulations of channel and boundary layers reaching δ+ ~ 2000 and δ+ ~ 700, respectively. To fill the gap in the Reynolds number, a new boundary layer simulation in the range δ+ ~ 1000-2000 is presented and discussed. The original raw data and the post-processed statistics are publicly available on our website.162 The analysis of the one-point statistic confirms the existence of logarithmic profiles for the spanwise w'2+ and pressure p'2+ fluctuations for both type of flows, but not for the wall-normal v'2+ or the streamwise u'2+ velocities. To accept or reject the existence of a logarithmic range in u'2+ requires higher Reynolds numbers than the ones considered in this work. An important consequence of having such profiles is that the maximum value of the intensities, reached near the wall, depends on the Reynolds number. This was confirmed after surveying a wide number of experimental and numerical datasets, corrob¬orating that the maximum of ul2+, p'2+, and w'2+ increases proportionally to log(δ+). On the other hand, that maximum is more intense in external flows than in internal ones, differing the most around y/δ ~ 0.3-0.5, and essentially independent of the Reynolds number. We discuss that those differences are originated as a consequence of the inter¬mittent character of boundary layers that is absent in internal flows. The structure of the velocity and pressure fluctuations, together with those of the Reynolds shear stress, were investigated using three-dimensional two-point spatial correlations. We find that the correlations extend over longer distances in channels than in boundary layers, especially in the case of the streamwise correlation Cuu in the flow direc-tion. For weakly correlated structures, the maximum streamwise length of Cuu is O(78) for boundary layers and O(188) for channels, attained at the logarithmic and outer regions respectively. The corresponding lengths for the transverse velocities and for the pressure are shorter, 0(8 — 28), and of the same order for both flows. The spatial organization of the velocity correlations is shown to be consistent with a pair of quasi-streamwise rollers that scales in outer units. That organization is observed until y ~ 0.68, from which boundary layers start to organize into spanwise rollers. This effect is weaker in channels, and it appears at y ~ 0.88. We present correlations conditioned to intense events of the transversal velocity, w', to study if these structures meander along the spanwise direction. The results indicate that the streamwise velocity streaks increase their meandering proportionally to the distance to the wall, suggesting that the structures are more aligned close to the wall than far from it. The reason behind this meandering is probably due to the characteristic organization along diagonals of w'. These structures not only meander along the spanwise direction, but they are also inclined to the wall at angles that depend on the distance from the wall, on the variable being considered, and on the correlation level used to define them. Above the buffer layer and independent of the Reynolds numbers and type of flow, the maximum inclination of Cuu is about 10°, Cvv and Cpp are roughly vertical, and Cww is inclined by 35°.

Simulating potential growth and yield of oil palm (Elaeis guineensis) with PALMSIM: Model description, evaluation and application.

Reducing the gap between water-limited potential yield and actual yield in oil palm production systems through intensification is seen as an important option for sustainably increasing palm oil production. Simulation models can play an important role in quantifying water-limited potential yield, and therefore the scope for intensification, but no oil palm model exists that is both simple enough and at the same time incorporates sufficient plant physiological knowledge to be generally applicable across sites with different growing conditions. The objectives of this study therefore were to develop a model (PALMSIM) that simulates, on a monthly time step, the potential growth of oil palm as determined by solar radiation and to evaluate model performance against measured oil palm yields under optimal water and nutrient management for a range of sites across Indonesia and Malaysia. The maximum observed yield in the field matches the corresponding simulated yield for dry bunch weight with a RMSE of 1.7 Mg ha?1 year?1 against an observed yield of 18.8 Mg ha?1. Sensitivity analysis showed that PALMSIM is robust: simulated changes in yield caused by modifying the parameters by 10% are comparable to other tree crop model evaluations. While we acknowledge that, depending on the soils and climatic environment, yields may be often water limited, we suggest a relatively simple physiological approach to simulate potential yield, which can be usefully applied to high rainfall environments and is considered as a first step in developing an oil palm model that also simulates water-limited potential yield. To illustrate the application possibil- ities of the model, PALMSIM was used to create a potential yield map for Indonesia and Malaysia by sim- ulating the growth and yield at a resolution of 0.1?. This map of potential yield is considered as a first step towards a decision support tool that can identify potentially productive, but at the moment degraded sites in Indonesia and Malaysia. ?

Flamelet structures in spray ignition

In typical liquid-fueled burners the fuel is injected as a high-velocity liquid jet that breaks up to form the spray. The initial heating and vaporization of the liquid fuel rely on the relatively large temperatures of the sourrounding gas, which may include hot combustion products and preheated air. The heat exchange between the liquid and the gas phases is enhanced by droplet dispersion arising from the turbulent motion. Chemical reaction takes place once molecular mixing between the fuel vapor and the oxidizer has occurred in mixing layers separating the spray flow from the hot air stream. Since in most applications the injection velocities are much larger than the premixed-flame propagation velocity, combustion stabilization relies on autoignition of the fuel-oxygen mixture, with the combustion stand-off distance being controlled by the interaction of turbulent transport, droplet heating and vaporization, and gas-phase chemical reactions. In this study, conditions are identified under which analyses of laminar flamelets canshed light on aspects of turbulent spray ignition. This study extends earlier fundamental work by Liñan & Crespo (1976) on ignition in gaseous mixing layers to ignition of sprays. Studies of laminar mixing layers have been found to be instrumental in developing un-derstanding of turbulent combustion (Peters 2000), including the ignition of turbulent gaseous diffusion flames (Mastorakos 2009). For the spray problem at hand, the configuration selected, shown in Figure 1, involves a coflow mixing layer formed between a stream of hot air moving at velocity UA and a monodisperse spray moving at velocity USUA. The boundary-layer approximation will be used below to describe the resulting sl ender flow, which exhibits different igniting behaviors depending on the characteristics of t he fuel. In this approximation, consideration of the case U A = U S enables laminar ignition distances to be related to ignition times of unstrained spray flamelets, thereby pro viding quantitative information of direct applicability in regions of low scala r dissipation-rate in turbulent reactive flows (see the discussion in pp. 181–186 of Peters (2000)) . This report is organized as follows. Effects of droplet dispersion dynamics on ignition of sprays in turbulent mixing layers are discussed in Section 2. The formulation f or ignition in laminar mixing layers is outlined in Sections 3 and 4. The results are presented in Section 5. In Section 6, the mixture-fraction field and associated scalar dissipat ion rates for spray ignition are discussed. Finally, some brief conclusions are drawn in Section 7.

Respuesta fisiológica y agronómica del olivar en seto (cv. Arbequina) a la orientación de filas y al ancho de calle: relación entre la producción y calidad del aceite y la radiación interceptada

En las últimas dos décadas, los productores han plantado olivares en seto para lograr la mecanización de la poda y en especial de la cosecha, reducir los costes de mano de obra y permitir intervenciones de manejo rápidas y oportunas. Los olivares se desarrollaron en ausencia del conocimiento científico, sobre el diseño óptimo de la estructura de la copa, necesario para incrementar la producción y calidad del aceite. En contraste, con los árboles muy espaciados y distribuidos uniformemente de las plantaciones tradicionales, en el olivar en seto hay una marcada variabilidad espacial y temporal de la radiación disponible en función del diseño de la plantación. Así, conocer la respuesta fisiológica y productiva del olivo a la radiación resulta fundamental en el olivar en seto. La orientación de las filas y el ancho de calle son aspectos que se deciden en el diseño de las plantaciones en seto. Ambos aspectos modifican la radiación interceptada por la canopia y, por lo tanto, pueden incidir en la productividad y calidad del aceite. Una vez realizada la plantación no pueden ser modificados, y así las ventajas o desventajas permanecerán fijas durante toda la vida productiva del olivar. A pesar de esto, el impacto de la orientación de las filas y el ancho de calle han recibido poca atención en olivos y en la mayoría de los frutales conducidos en seto. Por todo ello, los objetivos principales de esta tesis fueron, (i) evaluar el efecto de la orientación del seto y del ancho de calle, sobre la productividad y calidad del aceite, (ii) evaluar un modelo que estime la radiación dentro de la canopia. Este modelo permitirá cuantificar las relaciones entre la radiación y los componentes del rendimiento y calidad del aceite de olivares en setos con un amplio rango de estructuras y (iii) conocer la variabilidad en las características de las hojas (morfológicas y fisiológicas) y de los tejidos del fruto (tamaño y composición) en diferentes posiciones de la copa de los setos. Para ello, se dispuso de 3 ensayos de olivar en seto (cv. Arbequina) implantados en 2008 en el municipio de La Puebla de Montalbán, Toledo. La primera cosecha fue en 2010 y a partir del 2012 los setos formaron una copa continua. A partir de ese año, los setos se mantuvieron mediante poda, con similar ancho (~1 m) y altura (~2,5 m), acordes a las dimensiones de la cosechadora vendimiadora. En los años 2012 y 2013 se estudió en profundidad la respuesta de las plantas de estos ensayos. En el ensayo 1, los setos fueron plantados con cuatro orientaciones de filas: N–S, NE–SO, NO–SE y E–O y el mismo ancho de calle (4 m). En los otros dos ensayos, los setos fueron plantados con tres anchos de calle (5,0, 4,0 y 2,5 m), y con filas orientadas N–S (ensayo 2) y E–O (ensayo 3). La respuesta de la orientación de las filas se evaluó a nivel de seto y de estratos del seto (alturas y caras), a través de mediciones del crecimiento de brotes, componentes reproductivos, características y temperatura del fruto, estado hídrico del suelo y de las plantas, fotosíntesis neta de las hojas y contenido de ácidos grasos. Los setos orientados NE–SO (2,7 t/ha) lograron la mayor producción de aceite, que fue significativamente más alta que la de los setos E–O (2,3 t/ha). La producción de aceite de los setos E–O no se diferenció estadísticamente de los setos N–S (2,5 t/ha). Las diferencias productivas entre orientaciones fueron explicadas por el número de frutos en cosecha, a su vez la variación en el número de frutos estuvo asociada al efecto de la orientación de las filas sobre el número de yemas desarrolladas y el porcentaje de inflorescencias fértiles. Las hojas en las caras iluminadas de los setos NE–SO y N–S presentaron mayor tasa fotosintética a la mañana (~10.0 h) que los setos E–O, en el año 2012, pero no en 2013. La orientación de las filas no tuvo un efecto significativo en el contenido de ácidos grasos de los aceites extraídos, esto ocurrió a pesar de variaciones en la temperatura interna de los frutos (3 °C) y de la radiación (40%) entre las distintas caras de los setos. La orientación del seto afectó significativamente al contenido relativo de agua del suelo, donde setos E–O presentaron valores más altos (12%) que setos N–S durante el verano y otoño. Sin embargo, el potencial hídrico de tallo fue similar entre orientaciones. En los ensayos 2 y 3, se evaluó el efecto que produce, a nivel de seto y de estratos (caras y alturas), reducir el ancho de calle de 5,0 a 4,0 y 2,5 m, en un seto orientado N–S y otro E–O, respectivamente. La relación entre altura/ancho de calle libre aumentó 0,6 a 0,8 y 1,6, al reducir 5,0, 4,0 y 2,5 m el ancho de calle, mientras la longitud de seto y el volumen de copa por hectárea incrementó 100% al reducir de 5,0 a 2,5 m, el ancho de calle. En los setos orientados N–S, la producción de aceite por ha acumulada en 4 campañas, incrementó significativamente un 52 %, al reducir de 5,0 a 2,5 m el ancho de calle. Los setos N–S con calle más estrecha (2,5 m) tuvieron un 19% menos frutos que los setos con calle más ancha (5,0 m) y a su vez el 60% de los mismos se localizaron los estratos altos de la canopia de los setos con calles estrecha en comparación al 40% en setos con calle de 5,0 m. En los estratos más bajos de los setos con calles de 2,5m hubo menor crecimiento de los brotes y los frutos tuvieron menor peso seco, contenido de aceite y madurez, que los frutos en los estratos bajos de los setos a 5,0 m. Los componentes del rendimiento y características de los frutos (agua y madurez) fueron similares entre la caras E y O, independientemente del ancho de calle. En los setos orientados E–O, la producción de aceite por ha acumulada en 4 campañas, no respondió significativamente al ancho de calle, debido a una disminución significativa en el número de frutos y producción de aceite por m de seto, al reducir de 5,0 a 2,5 m, el ancho de calle. En los setos orientados E–O, con calles de 5,0 m, los frutos presentaron similar peso seco, contenido de aceite y agua, en las caras S y N, sin embargo, cuando la calle fue reducida a 2,5, los frutos de la cara S fueron más pesado y maduros que en la cara N. Independientemente del ancho de calle y de la orientación del seto, el aceite presentó mayor contenido de ácidos palmitoleico, palmítico, esteárico y linoleico en los frutos del estrato más alto de la canopia disminuyendo hacia la base. En contraste, el contenido de ácido oleico aumentó desde el estrato más alto hacia la base de los setos. Las diferencias en el contenido de ácidos grasos entre la parte alta y baja de los setos, incrementó al reducir el ancho de calle en los setos N–S, pero no en los E-O. En conclusión, en olivares en seto, reducir el ancho de calle permite incrementar la producción de aceite, en setos orientados N–S, pero no en E–O. Un modelo que estima la cantidad y distribución de la radiación en toda la copa del seto, fue utilizado para estimar la radiación interceptada en distintos estratos del seto. El modelo requiere un valor del coeficiente de extinción (k) para estimar la transmisión de radiación a través de la copa, el cual fue obtenido experimentalmente (k=1,2). Utilizando los datos del ensayo 1, un único modelo lineal relacionó el peso seco y el rendimiento graso de setos con la radiación interceptada por los distintos estratos de setos con cuatro orientaciones de filas. La densidad de frutos fue también relacionada con la radiación, pero más débilmente. En los setos orientados N–S, plantados con tres anchos de calles, (ensayo 2) el contenido de ácidos palmitoleico y linoleico del aceite incrementó linealmente con el incremento de la radiación interceptada, mientras el contenido ácido oleico disminuyó linealmente con el incremento de la radiación. El contenido de ácidos grasos del aceite no estuvo relacionado con la radiación interceptada en setos orientados E–O (Ensayo 3). En los setos N–S y E–O, plantados con anchos de calle de 2,5 m, se estudiaron las interacciones entre la radiación y características de las hojas, número de fruto, tamaño y composición de los frutos a nivel de órgano, tejido y células. Independientemente de la orientación del seto, el área y el contenido de clorofila de las hojas incrementaron significativamente en los estratos más bajos de los setos. Mientras, las hojas de los estratos medios del seto presentaron mayor capacidad fotosintética que en los estratos bajos y alto de los setos. Los estratos del seto que interceptaron más radiación produjeron frutos con mayor tamaño y contenido de aceite en el mesocarpo, sin efectos sobre el tamaño y composición del endocarpo. A nivel celular, los frutos expuestos a mayor nivel de radiación desarrollaron en el mesocarpo células de mayor tamaño en comparación a frutos menos expuestos, mientras el número de células no fue afectado. Adicionalmente, el número y tamaño de las células estuvo relacionado con la composición del mesocarpo en términos de aceite, agua y peso seco menos aceite. Esta tesis, contribuye, desde una perspectiva integral del cultivo del olivo, a cuantificar el impacto de la orientación y ancho de calle sobre la producción y calidad del aceite en olivares conducidos en setos. El análisis y discusión de la relación entre la radiación y los componentes del rendimiento y calidad del aceite, puede ayudar a diseñar plantaciones en seto con dimensiones óptimas para la intercepción de la radiación. ABSTRACT In the last two decades, olive hedgerow system has been established by commercial growers to allow continuous mechanized pruning and especially harvest, reduce costs of manual labour and allow more rapid and timely management interventions. The adoption of hedgerow was done in the absence of adequate scientific knowledge of the impact of this orchard structure and associated mechanization on tree response, yield and quality, after centuries in low-density orchards and open-formed trees. The row orientation and width alley are fundamental aspects in the hedgerow design and have been scarcely studied in olive. Both aspects modify the radiation intercepted by the canopy, and consequently the productivity and oil quality, and once defined in orchard planting cannot be changed, so advantages and disadvantages remain fixed for the lifespan of the orchard. The main objectives of this thesis were to (i) evaluate the impact of the row orientation and width alley on productivity and oil quality by the measurements of profile of the determining processes of shoot growth, fruit temperature, yield components and fruit and oil characteristics on opposite sides of olive hedgerows. Additionally, the effect of row orientation on the plant water status was also evaluated; (ii) evaluate a mathematical model for estimating the radiation within the canopy and quantify the relationships between the radiation estimated and yield components and oil quality in olive hedgerows under wide range of structures and; (iii) determine the variability in the characteristics of the leaves (morphological and physiological) and fruit tissues (size and composition) in different positions of the hedgerows canopy. Three plots of olive hedgerows (cv. Arbequina) planted in 2008 in La Puebla de Montalbán, Toledo were evaluated during the 2012 and 2013 seasons. The hedgerows were maintained by lateral pruning and topping with the same width (1 m) and height (2.5 m) compatible with the intended harvester. In a plot (experiment 1), the hedgerows were planted with the same width alley (4 m) and four row orientations: N–S, NE–SW, NW–SE and E–W. Other two plots (Experiments 2 and 3) separated by approximately 100 m were planted with N–S and E–O oriented rows and three alley widths in each orientation: 5.0, 4.0 and 2.5 m. In the exp. 1, maximum fruit yield were achieved by NE–SW and NW–SW (15.7 t/ha). Of these, NE–SW achieved the highest oil yield (2.7 t/ha). There were no differences in fruit or oil yield between N–S (2.5 t oil/ha) and E–W (2.3 t oil/ha) orientations. Fruit number was the most important component to explain these differences, by previous influence on number of bud developed and percentage of fertile inflorescences. Fruit maturity and oil quality on both sides of the hedgerows were not affected by row orientation. This occurred despite significant variations in the internal fruit temperature, which was closely related to the irradiance received by the canopy and the time of day. Additionally, row orientation significantly affected the relative water content of the soil, where E–W oriented hedgerows showed consistently higher values than N–S during summer-autumn season. The stem water potential at midday, however, was similar between orientations, revealing possible lower water consumption of E–W than N–S oriented hedgerows. In the exp. 2, regardless of row orientation, reduction of row spacing from 5.0 to 4.0 and 2.5 m increases the ratio of canopy depth to free alley width (Al/An) from 0.6 to 0.8 and 1.6, respectively, and ads 25 and 100 % more hedgerow length per ha. In N–S oriented hedgerows, oil production per ha increased significantly by 14 and 52 % in 4.0 m and 2.5 m relative to 5.0 m row spacing, the effect being proportionally less than the increase in hedgerow length per ha. Hedgerows spaced 2.5 m with Al/An = 1.6 produced relatively fewer fruits per unit length than did wider spacings and were preferentially distributed in upper layers. Fruits located at the bottom of the canopy were smaller, with lower oil content and were less mature. In E–W oriented hedgerows, oil production per ha did not respond significantly to row spacing, despite the doubling of row length from the 5.0 to the 2.5 m row spacing. The explanation was found in fewer fruit per unit length of hedgerow and smaller oil content at 2.5 m than 5.0 m row spacing, averaged over the experimental period. In E–W hedgerows spaced at 5.0 m with Al/An = 0.6, the vertical profiles of fruit characteristics (mass, oil and water contents, and maturity) were similar between opposing sides, but at 4.0 m (Al/An= 0.8) and 2.5 m (Al/An=1.6) spacings, fruits on the S side were heavier and more mature than on N side. The oil extracted from fruits harvested at different heights of N–S and E–W oriented hedgerows showed higher palmitoleic, palmitic, stearic and linoleic contents at the canopy top decreasing toward base. The oleic content was reverse, increased from top to base. In N–S hedgerows, vertical gradients increased by reducing the alley width, but not in the E–W oriented hedgerows. The simulation of internal canopy irradiance was related in a single relationship (R2 = 0.63) to the vertical profiles of fruit weight and oil content of olive hedgerows with wide range of structures. The density of fruits was also associated with the irradiance but more weakly (R2 = 0.27), and revealed a more complex response involving changes in the vegetative structure by canopy management (topping) and the effect of radiation on the previous sequence that defines the number of fruits. The vertical profiles of oil quality traits were closely associated to canopy irradiance, but only when the N–S oriented hedgerows were considered. The contents of palmitoleic and linoleic acid in the oil increased linearly when intercepted irradiance increased from 9 to 19 mol PAR/m2. In contrast, oleic content decreased linearly in this irradiance range. Additionally, we advanced knowledge regarding the interactions among irradiance and leaf, fruit number, size and composition at organ-, tissue- and cellular- levels. The irradiance received at different positions in the canopy strongly affected the leaf area and chlorophyll content, and mesocarp size and composition (water and oil), without effects on endocarp size and composition. At the cellular level, light-exposed fruit developed larger mesocarp cells than shaded fruits, but cell number was not affected. Our results indicate that cell number and size are related to mesocarp composition in term of oil, water, and dry weight menus oil, although the specific manner in which they interact remains to be determined. This research contributes from an integral perspective of olive growing to quantify the impact of row orientation and width alley on productivity and oil quality in hedgerows systems. The analysis and discussion of the relationships between radiation and yield components and oil quality can help understand the impact of design olive hedgerows in general and in a wide range of environmental conditions.

Availability and uptake of trace elements in a forage rotation under conservation and plough tillage

After 14 years under conventional plough tillage (CT) or conservation minimum tillage (MT), the soil available Al, Fe, Mn, Cu and Zn (0-5, 5-15 and 15-30 cm layers) and their plant uptake were evaluated during two years in a ryegrass-maize forage rotation in NW Spain (t emperate-humid region). The three-way ANOVA showed that trace element concentrations in soil were mainly influenced by sampling date, followed by soil depth and tillage system (35-73 %, 7-58 % and 3- 11 % of variance explained, respectively). Excepting for Fe (CT) and Al (CT and MT), the elemental concentrations decreased with depth, the stratification being stronger under MT. For soil available Al, Fe, Mn and Cu, the concentrations were higher in CT than in MT (5-15 and 15-30 cm layers) or were not affected by tillage system (0-5 cm). In contrast, the available Zn contents were higher in MT than CT at the soil surface and did not differ in deeper layers. The concentration of Al, Fe and Cu in crops were not influenced by tillage system, which explain 22 % of Mn variance in maize (CT > MT in the more humid year) and 18 % of Zn variance in ryegrass (MT > CT in both years). However, in the summer crop (maize) the concentrations of Fe, Mn and Zn tended to be higher in MT than in CT under drought conditions, while the opposite was true in the year without water limitation. Therefore, under the studied conditions of climate, soil, tillage and crop rotation, little influence of tillage system on crop nutritive value would be expected. To minimize the potential deficiency of Zn (maize) and Cu (maize and ryegrass) on crop yields the inclusion of these micro-nutrients in fertilization schedule is reco mmended, as well as liming to alleviate Al toxicity on maize crops.

Induction of through-thickness compressive residual stress fields in thin Al2024-T351 plates by laser shock processing

Laser Shock Processing (LSP) has been demonstrated as an emerging technique for the induction of RS’s fields in subsurface layers of relatively thick specimens. However, the LSP treatment of relatively thin specimens brings, as an additional consequence, the possible bending in a process of laser shock forming. This effect poses a new class of problems regarding the attainment of specified RS’s depth profiles in the mentioned type of sheets, and, what can be more critical, an overall deformation of the treated component. The analysis of the problem of LSP treatment for induction of tentatively through-thickness RS’s fields for fatigue life enhancement in relatively thin sheets in a way compatible with reduced overall workpiece deformation due to spring-back self-equilibration is envisaged in this paper. The coupled theoretical-experimental predictive approach developed by the authors has been applied to the specification of LSP treatments for achievement of RS's fields tentatively able to retard crack propagation on normalized specimens. A convergence between numerical code results and experimental results coming from direct RS's measurement is presented as a first step for the treatment of the normalized specimens under optimized conditions and verification of the crack retardation properties virtually induced.

Identificación de los riesgos ambientales y sanitarios de la producción de gas mediante fracturación hidráulica y bases para una propuesta metodológica de vulnerabilidad de las aguas subterráneas

Hasta ahora, la gran mayoría de los recursos explotados de gas natural procedían de acumulaciones convencionales de gas aislado y de gas asociado y disuelto en el petróleo. Sin embargo, el gas natural se encuentra también en yacimientos que, debido a su baja porosidad y permeabilidad, tienen unas características que hacen que hasta muy recientemente no hayan sido económicamente rentables y que sólo puedan ser explotados mediante técnicas no convencionales, dando lugar al denominado gas no convencional. Las técnicas utilizadas para su extracción son la fracturación hidráulica o “fracking” y la perforación horizontal. Entre los diversos tipos de gas no convencional, es de prever que el gas de pizarra sea el que sufra mayor desarrollo a medio plazo en nuestro país, por lo que se están generando grandes debates, debido al riesgo de contaminación de las aguas superficiales y subterráneas del entorno, provocados por la elevada cantidad de agua utilizada, los aditivos empleados, los fluidos de retorno, por la alteración del medio físico, así como por la dificultad de monitorización de estos procesos. En este proyecto se identifican los riesgos ambientales y sanitarios asociados a la extracción de gas no convencional. El trabajo se basa principalmente en experiencias ocurridas en países donde el fracking se ha convertido en una práctica habitual. Se trata además de establecer las bases necesarias para la estimación de la vulnerabilidad de los acuíferos frente a la contaminación inducida por la fracturación hidráulica. Abstract Until now, most of the natural gas resources exploited were from isolated conventional gas accumulations and associated and dissolved gas in oil. However, the natural gas is also in reservoirs that, due to their low porosity and permeability, have characteristics that make until recently not been economically profitable and can be exploited only by unconventional techniques, leading to the so called unconventional gas. The techniques used for extraction are hydraulic fracturing or "fracking" and horizontal drilling. Among the various types of unconventional gas, it is expected that shale gas is the suffering greater medium-term development in our country, so it is generating much debate, due to the risks of contamination in surface waters and subterranean environment, caused by the high amount of water used, the additives used, the return fluid, by altering the physical environment, and the difficulty of monitoring these processes. In this project identifies the environmental and health risks associated with unconventional gas extraction. The work is mainly based on experiences that occurred in countries where fracking has become a common practice. This is for establish the necessary basis for estimating the vulnerability of aquifers from contamination induced by hydraulic fracturing.

Interfaz gráfica y fase de pruebas de software de vídeo forense (Sistema de codificación DV)

El presente proyecto fin de carrera, realizado por el ingeniero técnico en telecomunicaciones Pedro M. Matamala Lucas, es la fase final de desarrollo de un proyecto de mayor magnitud correspondiente al software de vídeo forense SAVID. El propósito del proyecto en su totalidad es la creación de una herramienta informática capacitada para realizar el análisis de ficheros de vídeo, codificados y comprimidos por el sistema DV –Digital Video-. El objetivo del análisis, es aportar información acerca de si la cinta magnética presenta indicios de haber sido manipulada con una edición posterior a su grabación original, además, de mostrar al usuario otros datos de interés como las especificaciones técnicas de la señal de vídeo y audio. Por lo tanto, se facilitará al usuario, analista de vídeo forense, información que le ayude a valorar la originalidad del contenido del soporte que es sujeto del análisis. El objetivo específico de esta fase final, es la creación de la interfaz de usuario del software, que informa tanto del código binario de los sectores significativos, como de su interpretación tras el análisis. También permitirá al usuario el reporte de los resultados, además de otras funcionalidades que le permitan la navegación por los sectores del código que han sido modificados como efecto colateral de la edición de la cinta magnética original. Otro objetivo importante del proyecto ha sido la investigación de metodologías y técnicas de desarrollo de software para su posterior implementación, buscando con esto, una mayor eficiencia en la gestión del tiempo y una mayor calidad de software con el fin de garantizar su evolución y sostenibilidad en el futuro. Se ha hecho hincapié en las metodologías ágiles que han ido ganando relevancia en el sector de las tecnologías de la información en las últimas décadas, sustituyendo a metodologías clásicas como el desarrollo en cascada. Su flexibilidad durante el ciclo de vida del software, permite obtener mejores resultados cuando las especificaciones no están del todo definidas, ajustándose de este modo a las condiciones del proyecto. Resumiendo las especificaciones técnicas del software, C++ es el lenguaje de programación orientado a objetos con el que se ha desarrollado, utilizándose la tecnología MFC -Microsoft Foundation Classes- para la implementación. Es un proyecto MFC de tipo cuadro de dialogo,creado, compilado y publicado, con la herramienta de desarrollo integrado Microsoft Visual Studio 2010. La arquitectura con la que se ha estructurado es la arquetípica de tres capas, compuesta por la interfaz de usuario, capa de negocio y capa de acceso a datos. Se ha visto necesario configurar el proyecto con compatibilidad con CLR –Common Languages Runtime- para poder implementar la funcionalidad de creación de reportes. Acompañando a la aplicación informática, se presenta la memoria del proyecto y sus anexos correspondientes a los documentos EDRF –Especificaciones Detalladas de Requisitos funcionales-, EIU –Especificaciones de Interfaz de Usuario , DT -Diseño Técnico- y Guía de Usuario. SUMMARY. This dissertation, carried out by the telecommunications engineer Pedro M. Matamala Lucas, is in its final stage and is part of a larger project for the software of forensic video called SAVID. The purpose of the entire project is the creation of a software tool capable of analyzing video files that are coded and compressed by the DV -Digital Video- System. The objective of the analysis is to provide information on whether the magnetic tape shows signs of having been tampered with after the editing of the original recording, and also to show the user other relevant data and technical specifications of the video signal and audio. Therefore the user, forensic video analyst, will have information to help assess the originality of the content of the media that is subject to analysis. The specific objective of this final phase is the creation of the user interface of the software that provides information about the binary code of the significant sectors and also its interpretation after analysis. It will also allow the user to report the results, and other features that will allow browsing through the sections of the code that have been modified as a secondary effect of the original magnetic tape being tampered. Another important objective of the project is the investigation of methodologies and software development techniques to be used in deployment, with the aim of greater efficiency in time management and enhanced software quality in order to ensure its development and maintenance in the future. Agile methodologies, which have become important in the field of information technology in recent decades, have been used during the execution of the project, replacing classical methodologies such as Waterfall Development. The flexibility, as the result of using by agile methodologies, during the software life cycle, produces better results when the specifications are not fully defined, thus conforming to the initial conditions of the project. Summarizing the software technical specifications, C + + the programming language – which is object oriented and has been developed using technology MFC- Microsoft Foundation Classes for implementation. It is a project type dialog box, created, compiled and released with the integrated development tool Microsoft Visual Studio 2010. The architecture is structured in three layers: the user interface, business layer and data access layer. It has been necessary to configure the project with the support CLR -Common Languages Runtime – in order to implement the reporting functionality. The software application is submitted with the project report and its annexes to the following documents: Functional Requirements Specifications - Detailed User Interface Specifications, Technical Design and User Guide.

Diseño de los sistemas de comunicación en plantas de exploración y producción de hidrocarburos

Las plantas industriales de exploración y producción de petróleo y gas disponen de numerosos sistemas de comunicación que permiten el correcto funcionamiento de los procesos que tienen lugar en ella así como la seguridad de la propia planta. Para el presente Proyecto Fin de Carrera se ha llevado a cabo el diseño del sistema de megafonía PAGA (Public Address and General Alarm) y del circuito cerrado de televisión (CCTV) en la unidad de procesos Hydrocrcaker encargada del craqueo de hidrógeno. Partiendo de los requisitos definidos por las especificaciones corporativas de los grupos petroleros para ambos sistemas, PAGA y CCTV, se han expuesto los principios teóricos sobre los que se fundamenta cada uno de ellos y las pautas a seguir para el diseño y demostración del buen funcionamiento a partir de software específico. Se ha empleado las siguientes herramientas software: EASE para la simulación acústica, PSpice para la simulación eléctrica de las etapas de amplificación en la megafonía; y JVSG para el diseño de CCTV. La sonorización tanto de las unidades como del resto de instalaciones interiores ha de garantizar la inteligibilidad de los mensajes transmitidos. La realización de una simulación acústica permite conocer cómo va a ser el comportamiento de la megafonía sin necesidad de instalar el sistema, lo cual es muy útil para este tipo de proyectos cuya ingeniería se realiza previamente a la construcción de la planta. Además se comprueba el correcto diseño de las etapas de amplificación basadas en líneas de alta impedancia o de tensión constante (100 V). El circuito cerrado de televisión (CCTV) garantiza la transmisión de señales visuales de todos los accesos a las instalaciones y unidades de la planta así como la visión en tiempo real del correcto funcionamiento de los procesos químicos llevados a cabo en la refinería. El sistema dispone de puestos de control remoto para el manejo y gestión de las cámaras desplegadas; y de un sistema de almacenamiento de las grabaciones en discos duros (RAID-5) a través de una red SAN (Storage Area Network). Se especifican las diferentes fases de un proyecto de ingeniería en el sector de E&P de hidrocarburos entre las que se destaca: propuesta y adquisición, reunión de arranque (KOM, Kick Off Meeting), estudio in situ (Site Survey), plan de proyecto, diseño y documentación, procedimientos de pruebas, instalación, puesta en marcha y aceptaciones del sistema. Se opta por utilizar terminología inglesa dado al ámbito global del sector. En la última parte del proyecto se presenta un presupuesto aproximado de los materiales empleados en el diseño de PAGA y CCTV. ABSTRACT. Integrated communications for Oil and Gas allows reducing risks, improving productivity, reducing costs, and countering threats to safety and security. Both PAGA system (Public Address and General Alarm) and Closed Circuit Television have been designed for this project in order to ensure a reliable security of an oil refinery. Based on the requirements defined by corporate specifications for both systems (PAGA and CCTV), theoretical principles have been presented as well as the guidelines for the design and demonstration of a reliable design. The following software has been used: EASE for acoustic simulation; PSpice for simulation of the megaphony amplification loops; and JVSG tool for CCTV design. Acoustic for both the units and the other indoor facilities must ensure intelligibility of the transmitted messages. An acoustic simulation allows us to know how will be the performance of the PAGA system without installing loudspeakers, which is very useful for this type of project whose engineering is performed prior to the construction of the plant. Furthermore, it has been verified the correct design of the amplifier stages based on high impedance lines or constant voltage (100 V). Closed circuit television (CCTV) ensures the transmission of visual signals of all access to facilities as well as real-time view of the proper functioning of chemical processes carried out at the refinery. The system has remote control stations for the handling and management of deployed cameras. It is also included a storage system of the recordings on hard drives (RAID - 5) through a SAN (Storage Area Network). Phases of an engineering project in Oil and Gas are defined in the current project. It includes: proposal and acquisition, kick-off meeting (KOM), Site Survey, project plan, design and documentation, testing procedures (SAT and FAT), installation, commissioning and acceptance of the systems. Finally, it has been presented an estimate budget of the materials used in the design of PAGA and CCTV.