Sensitivity of a distributed temperature-radiation index melt model based on AWS observations and surface energy balance fluxes, Hurd Peninsula glaciers, Livingston Island, Antarctica

We use an automatic weather station and surface mass balance dataset spanning four melt seasons collected on Hurd Peninsula Glaciers, South Shetland Islands, to investigate the point surface energy balance, to determine the absolute and relative contribution of the various energy fluxes acting on the glacier surface and to estimate the sensitivity of melt to ambient temperature changes. Long-wave incoming radiation is the main energy source for melt, while short-wave radiation is the most important flux controlling the variation of both seasonal and daily mean surface energy balance. Short-wave and long-wave radiation fluxes do, in general, balance each other, resulting in a high correspondence between daily mean net radiation flux and available melt energy flux. We calibrate a distributed melt model driven by air temperature and an expression for the incoming short-wave radiation. The model is calibrated with the data from one of the melt seasons and validated with the data of the three remaining seasons. The model results deviate at most 140 mm w.e. from the corresponding observations using the glaciological method. The model is very sensitive to changes in ambient temperature: a 0.5 ◦ C increase results in 56 % higher melt rates.

Electrical energy balance contest in Solar Decathlon Europe 2012

Solar Decathlon Europe (SDE) is an international multidisciplinary competition in which 20 universityteams build and operate energy-efficient solar-powered houses. The aim of SDE is not only scientificbut also educational and divulgative, making visitors to understand the problems presented by realengineering applications and architecture. From a research perspective, the energy data gathered dur-ing the competition constitutes a very promising information for the analysis and understanding of thephotovoltaic systems, grid structures, energy balances and energy efficiency of the set of houses. Thisarticle focuses on the electrical energy components of SDE competition, the energy performance of thehouses and the strategies and behaviors followed by the teams. The rules evaluate the houses? electricalenergy self-sufficiency by looking at the electricity autonomy in terms of aggregated electrical energybalance; the temporary generation-consumption profile pattern correlation; and the use of electricityper measurable area. Although the houses are evaluated under the same climatological and consump-tion conditions, production results are very different due to the specific engineering solutions (differentelectrical topologies, presence or absence of batteries, diverse photovoltaic module solutions, etc.)

Multiple solutions and numerical analysis to the dynamic and stationary models coupling a delayed energy balance model involving latent heat and discontinuous albedo with a deep ocean

We study a climatologically important interaction of two of the main components of the geophysical system by adding an energy balance model for the averaged atmospheric temperature as dynamic boundary condition to a diagnostic ocean model having an additional spatial dimension. In this work, we give deeper insight than previous papers in the literature, mainly with respect to the 1990 pioneering model by Watts and Morantine. We are taking into consideration the latent heat for the two phase ocean as well as a possible delayed term. Non-uniqueness for the initial boundary value problem, uniqueness under a non-degeneracy condition and the existence of multiple stationary solutions are proved here. These multiplicity results suggest that an S-shaped bifurcation diagram should be expected to occur in this class of models generalizing previous energy balance models. The numerical method applied to the model is based on a finite volume scheme with nonlinear weighted essentially non-oscillatory reconstruction and Runge–Kutta total variation diminishing for time integration.

A mathematical framework for finite strain elastoplastic consolidation. Part 1: Balance laws, variational formulation, and linearization

A mathematical formulation for finite strain elasto plastic consolidation of fully saturated soil media is presented. Strong and weak forms of the boundary-value problem are derived using both the material and spatial descriptions. The algorithmic treatment of finite strain elastoplasticity for the solid phase is based on multiplicative decomposition and is coupled with the algorithm for fluid flow via the Kirchhoff pore water pressure. Balance laws are written for the soil-water mixture following the motion of the soil matrix alone. It is shown that the motion of the fluid phase only affects the Jacobian of the solid phase motion, and therefore can be characterized completely by the motion of the soil matrix. Furthermore, it is shown from energy balance consideration that the effective, or intergranular, stress is the appropriate measure of stress for describing the constitutive response of the soil skeleton since it absorbs all the strain energy generated in the saturated soil-water mixture. Finally, it is shown that the mathematical model is amenable to consistent linearization, and that explicit expressions for the consistent tangent operators can be derived for use in numerical solutions such as those based on the finite element method.

Energy requirements in pressure irrigation systems

Modernization of irrigation schemes, generally understood as transformation of surface irrigation systems into pressure –sprinkler and trickle- irrigation systems, aims at, among others, improving irrigation efficiency and reduction of operation and maintenance efforts made by the irrigators. However, pressure irrigation systems, in contrast, carry a serious energy cost. Energy requirements depend on decisions taken on management strategies during the operation phase, which are conditioned by previous decisions taken on the design project of the different elements which compose the irrigation system. Most of the countries where irrigation activity is significant bear in mind that modernization irrigation must play a key role in the agricultural infrastructure policies. The objective of this study is to characterize and estimate the mean and variation of the energy consumed by common types of irrigation systems and their management possibilities. The work includes all processes involved from the diversion of water into irrigation specific infrastructure to water discharge by the emitters installed on the crop fields. Simulation taking into account all elements comprising the irrigation system has been used to estimate the energy requirements of typical irrigation systems of several crop production systems. It has been applied to extensive and intensive crop systems, such us extensive winter crops, summer crops and olive trees, fruit trees and vineyards and intensive horticulture in greenhouses. The simulation of various types of irrigation systems and management strategies, in the framework imposed by particular cropping systems, would help to develop criteria for improving the energy balance in relation to the irrigation water supply productivity.

Energy saving potential of semi-transparent photovoltaic elements for building integration

Within the building energy saving strategies, BIPV (building integrated photovoltaic systems) present a promising potential based on the close relationship existing between these multifunctional systems and the overall building energy balance. Building integration of STPV (semi-transparent photovoltaic) elements affects deeply the building energy demand since it influences the heating, cooling and lighting loads as well as the local electricity generation. This work analyses over different window-to-wall ratios the overall energy performance of five STPV elements, each element having a specific degree of transparency, in order to assess the energy saving potential compared to a conventional solar control glass compliant with the local technical standard. The prior optical characterization, focused to measure the spectral properties of the elements, was experimentally undertaken. The obtained data were used to perform simulations based on a reference office building using a package of specific software tools (DesignBuilder, EnergyPlus, PVsyst, and COMFEN) to take proper account of the STPV peculiarities. To evaluate the global energy performance of the STPV elements a new Energy Balance Index was formulated. The results show that for intermediate and large façade openings the energy saving potential provided by the STPV solutions ranges between 18% and 59% compared to the reference glass.

Integral energy behaviour of photovoltaic semi-transparent glazing elements for building integration

La hipótesis general que esta tesis quiere demostrar es que la integración arquitectónica de sistemas fotovoltaicos semitransparentes (STPV) puede contribuir a mejorar la eficiencia energética de los edificios. Por lo tanto, la investigación se centra en el desarrollo de una metodología capaz de cuantificar la reducción de la demanda energética del edificio proporcionada por estas novedosas soluciones constructivas. Al mismo tiempo, los parámetros de diseño de las soluciones STPV se han analizado para establecer cuales presentan el mayor impacto sobre el balance energético global del edificio y por lo tanto tienen que ser cuidadosamente definidos a la hora de optimizar el comportamiento energético del mismo. A la luz de estos objetivos, la metodología de estudio se ha centrado en tres puntos principales:  Caracterizar el comportamiento energético global de sistemas STPV en condiciones de operación realistas, similares a las que se darían en un sistema real;  Caracterizar el comportamiento energético global de sistemas STPV en condiciones controladas, con el objetivo de estudiar la variación del comportamiento del los elementos en función de parámetro de diseño y operación;  Evaluar el potencial de ahorro energético global de los sistemas STPV en comparación con soluciones acristaladas convencionales al variar de las condiciones de contorno constituidas por los parámetros de diseño (como el grado de transparencia), las características arquitectónicas (como el ratio entre superficie acristalada y superficie opaca en la fachada del edificio) y las condiciones climáticas (cubriendo en particular la climatología europea). En síntesis, este trabajo intenta contribuir a comprender la interacción que existe entre los sistemas STPV y el edificio, proporcionando tanto a los fabricantes de los componentes como a los profesionales de la construcción información valiosa sobre el potencial de ahorro energético asociado a estos nuevos sistemas constructivos. Asimismo el estudio define los parámetros de diseño adecuados para lograr soluciones eficientes tanto en proyectos nuevos como de rehabilitación. ABSTRACT The general hypothesis this work seeks to demonstrate is that the architectural integration of Semi-Transparent Photovoltaic (STPV) systems can contribute to improving the energy efficiency of buildings. Accordingly, the research has focused on developing a methodology able to quantify the building energy demand reduction provided by these novel constructive solutions. At the same time, the design parameters of the STPV solution have been analysed to establish which of them have the greatest impact on the global energy balance of the building, and therefore which have to be carefully defined in order to optimize the building operation. In the light of these goals, the study methodology has focused on three main points:  To characterise the global energy behaviour of STPV systems in realistic operating conditions, similar to those in which a real system will operate;  To characterise the global energy behaviour of STPV systems in controlled conditions in order to study how the performance varies depending on the design and operating parameters;  To assess the global energy saving potential of STPV systems in comparison with conventional glazing solutions by varying the boundary conditions, including design parameters (such as the degree of transparency), architectural characteristics (such as the Window to Wall Ratio) and climatic conditions (covering the European climatic conditions). In summary, this work has sought to contribute to the understanding of the interaction between STPV systems and the building, providing both components manufacturers and construction technicians, valuable information on the energy savings potential of these new construction systems and defining the appropriate design parameters to achieve efficient solutions in both new and retrofitting projects.

Integración de sistemas fotovoltaicos en edificios de oficinas en bajas latitudes: estudio del balance energético aplicado a Brasil

La hipótesis que inspiró esta tesis sostiene que la integración de componentes fotovoltaicos en los cerramientos opacos y sombreamientos de huecos acristalados de edificios de oficinas en sitios ubicados en bajas latitudes, tomando como el ejemplo el caso concreto de Brasil, podría incrementar su eficiencia energética. Esta posibilidad se basa en el bloqueo de una parte significativa de la irradiación solar incidente en estos edificios, reduciendo así las cargas térmicas para la climatización y a la vez transformándola en energía eléctrica, a tal punto que se amortizan los costes de inversión en plazos aceptables a través de los ahorros en la demanda de energía. Para verificar esta hipótesis de partida se ha propuesto como objetivo general analizar la integración de elementos fotovoltaicos en cubiertas, muros opacos y sombreamiento de huecos acristalados desde la óptica del balance energético térmico y eléctrico. Inicialmente se presenta y analiza el estado del arte en los temas estudiados y la metodología de investigación, de carácter teórico basada en cálculos y simulaciones. A partir de un modelo tipo de edificio de oficinas situado en Brasil, se definen cuatro casos de estudio y una serie de parámetros, los cuales se analizan para siete latitudes ubicadas entre -1,4° y -30°, separadas las unas de las otras por aproximadamente 5°. Se presentan y discuten los resultados de más de 500 simulaciones para los siguientes conceptos: - recurso solar, desde la perspectiva de la disponibilidad de irradiación solar en distintas superficies de captación apropiadas para la integración de sistemas solares fotovoltaicos en edificaciones en bajas latitudes; - análisis de sombras, con objetivo de identificar los ángulos de sombras vertical (AVS) para protección de huecos acristalados en edificios de oficinas; - balance energético térmico, para identificar el efecto térmico del apantallamiento provocado por componentes fotovoltaicos en cubiertas, muros opacos y parasoles en ventanas en las cargas de refrigeración y consecuentemente en las demandas de energía eléctrica; - balance energético eléctrico, contrastando los resultados del balance térmico con la energía potencialmente generada en las envolventes arquitectónicas bajo estudio; - análisis económico, basado en un escenario de precios de la tecnología fotovoltaica de un mercado maduro y en la política de inyección a la red marcada por la actual normativa brasileña. Se han verificado los potenciales de ahorro económico que los sistemas activos fotovoltaicos podrían aportar, y asimismo se calculan diversos indicadores de rentabilidad financiera. En suma, esta investigación ha permitido extraer conclusiones que contribuyen al avance de la investigación y entender las condiciones que propician la viabilidad de la aplicación de componentes fotovoltaicas en las envolventes de edificios en Brasil, y hasta un cierto punto en otros países en latitudes equivalentes. ABSTRACT The hypothesis that inspired this thesis sustains that integration of photovoltaic components in the opaque envelope and shading elements of office buildings placed at low-latitude countries, using the specific case of Brazil, could increase its energy efficiency. This is possible because those components block a significant part of the incident solar irradiation, reducing its heating effect on the building and transforming its energy into electricity in such a way that the extra investments needed can be paid back in acceptable periods given the electricity bill savings they produce. In order to check this hypothesis, the main goal was to analyze the thermal and electrical performance of photovoltaic components integrated into roofs, opaque façades and window shadings. The first step is an introduction and discussion of the state of the art in the studied subjects, as well as the chosen methodology (which is theoretical), based on calculations and simulations. Starting from an office building located in Brazil, four case studies and their parameters are defined, and then analyzed, for seven cities located between latitudes -1.4° and -30°, with an approximate distance of 5° separating each one. Results of more than 500 simulations are presented and discussed for the following concepts: - Solar resource, from the perspective of irradiation availability on different surfaces for the integration of photovoltaic systems in buildings located at low latitudes; - Shading analysis, in order to determine the vertical shading angles (VSA) for protection of the glazed surfaces on office buildings; - Thermal energy balance, to identify the screening effect caused by photovoltaic components on roofs, opaque façades and window shadings on the cooling loads, and hence electricity demands; - Electric energy balance, comparing thermal energy balance with the energy potentially generated using the active skin of the buildings; - Economic analysis, based on a mature-market scenario and the current net metering rules established by the Brazilian government, to identify the potential savings these photovoltaic systems could deliver, as well as several indicators related to the return on the investment. In short, this research has led to conclusions that contribute to the further development of knowledge in this area and understanding of the conditions that favor the application of photovoltaic components in the envelope of office buildings in Brazil and, to a certain extent, in other countries at similar latitudes.

Flujo de potencia entre estructuras complejas sometidas a excitaciones de alta frecuencia y aplicaciones a la detección de daño estructural

El tema central de investigación en esta Tesis es el estudio del comportamientodinámico de una estructura mediante modelos que describen la distribución deenergía entre los componentes de la misma y la aplicación de estos modelos parala detección de daños incipientes.Los ensayos dinámicos son un modo de extraer información sobre las propiedadesde una estructura. Si tenemos un modelo de la estructura se podría ajustar éstepara que, con determinado grado de precisión, tenga la misma respuesta que elsistema real ensayado. Después de que se produjese un daño en la estructura,la respuesta al mismo ensayo variará en cierta medida; actualizando el modelo alas nuevas condiciones podemos detectar cambios en la configuración del modeloestructural que nos condujeran a la conclusión de que en la estructura se haproducido un daño.De este modo, la detección de un daño incipiente es posible si somos capacesde distinguir una pequeña variación en los parámetros que definen el modelo. Unrégimen muy apropiado para realizar este tipo de detección es a altas frecuencias,ya que la respuesta es muy dependiente de los pequeños detalles geométricos,dado que el tamaño característico en la estructura asociado a la respuesta esdirectamente proporcional a la velocidad de propagación de las ondas acústicas enel sólido, que para una estructura dada es inalterable, e inversamente proporcionala la frecuencia de la excitación. Al mismo tiempo, esta característica de la respuestaa altas frecuencias hace que un modelo de Elementos Finitos no sea aplicable enla práctica, debido al alto coste computacional.Un modelo ampliamente utilizado en el cálculo de la respuesta de estructurasa altas frecuencias en ingeniería es el SEA (Statistical Energy Analysis). El SEAaplica el balance energético a cada componente estructural, relacionando la energíade vibración de estos con la potencia disipada por cada uno de ellos y la potenciatransmitida entre ellos, cuya suma debe ser igual a la potencia inyectada a cadacomponente estructural. Esta relación es lineal y viene caracterizada por los factoresde pérdidas. Las magnitudes que intervienen en la respuesta se consideranpromediadas en la geometría, la frecuencia y el tiempo.Actualizar el modelo SEA a datos de ensayo es, por lo tanto, calcular losfactores de pérdidas que reproduzcan la respuesta obtenida en éste. Esta actualización,si se hace de manera directa, supone la resolución de un problema inversoque tiene la característica de estar mal condicionado. En la Tesis se propone actualizarel modelo SEA, no en término de los factores de pérdidas, sino en términos deparámetros estructurales que tienen sentido físico cuando se trata de la respuestaa altas frecuencias, como son los factores de disipación de cada componente, susdensidades modales y las rigideces características de los elementos de acoplamiento.Los factores de pérdidas se calculan como función de estos parámetros. Estaformulación es desarrollada de manera original en esta Tesis y principalmente sefunda en la hipótesis de alta densidad modal, es decir, que en la respuesta participanun gran número de modos de cada componente estructural.La teoría general del método SEA, establece que el modelo es válido bajounas hipótesis sobre la naturaleza de las excitaciones externas muy restrictivas,como que éstas deben ser de tipo ruido blanco local. Este tipo de carga es difícil dereproducir en condiciones de ensayo. En la Tesis mostramos con casos prácticos queesta restricción se puede relajar y, en particular, los resultados son suficientementebuenos cuando la estructura se somete a una carga armónica en escalón.Bajo estas aproximaciones se desarrolla un algoritmo de optimización por pasosque permite actualizar un modelo SEA a un ensayo transitorio cuando la carga esde tipo armónica en escalón. Este algoritmo actualiza el modelo no solamente parauna banda de frecuencia en particular sino para diversas bandas de frecuencia demanera simultánea, con el objetivo de plantear un problema mejor condicionado.Por último, se define un índice de daño que mide el cambio en la matriz depérdidas cuando se produce un daño estructural en una localización concreta deun componente. Se simula numéricamente la respuesta de una estructura formadapor vigas donde producimos un daño en la sección de una de ellas; como se tratade un cálculo a altas frecuencias, la simulación se hace mediante el Método delos Elementos Espectrales para lo que ha sido necesario desarrollar dentro de laTesis un elemento espectral de tipo viga dañada en una sección determinada. Losresultados obtenidos permiten localizar el componente estructural en que se haproducido el daño y la sección en que éste se encuentra con determinado grado deconfianza.AbstractThe main subject under research in this Thesis is the study of the dynamic behaviourof a structure using models that describe the energy distribution betweenthe components of the structure and the applicability of these models to incipientdamage detection.Dynamic tests are a way to extract information about the properties of astructure. If we have a model of the structure, it can be updated in order toreproduce the same response as in experimental tests, within a certain degree ofaccuracy. After damage occurs, the response will change to some extent; modelupdating to the new test conditions can help to detect changes in the structuralmodel leading to the conclusión that damage has occurred.In this way incipient damage detection is possible if we are able to detect srnallvariations in the model parameters. It turns out that the high frequency regimeis highly relevant for incipient damage detection, because the response is verysensitive to small structural geometric details. The characteristic length associatedwith the response is proportional to the propagation speed of acoustic waves insidethe solid, but inversely proportional to the excitation frequency. At the same time,this fact makes the application of a Finite Element Method impractical due to thehigh computational cost.A widely used model in engineering when dealing with the high frequencyresponse is SEA (Statistical Energy Analysis). SEA applies the energy balance toeach structural component, relating their vibrational energy with the dissipatedpower and the transmitted power between the different components; their summust be equal to the input power to each of them. This relationship is linear andcharacterized by loss factors. The magnitudes considered in the response shouldbe averaged in geometry, frequency and time.SEA model updating to test data is equivalent to calculating the loss factorsthat provide a better fit to the experimental response. This is formulated as an illconditionedinverse problem. In this Thesis a new updating algorithm is proposedfor the study of the high frequency response regime in terms of parameters withphysical meaning such as the internal dissipation factors, modal densities andcharacteristic coupling stiffness. The loss factors are then calculated from theseparameters. The approach is developed entirely in this Thesis and is mainlybased on a high modal density asumption, that is to say, a large number of modescontributes to the response.General SEA theory establishes the validity of the model under the asumptionof very restrictive external excitations. These should behave as a local white noise.This kind of excitation is difficult to reproduce in an experimental environment.In this Thesis we show that in practical cases this assumption can be relaxed, inparticular, results are good enough when the structure is excited with a harmonicstep function.Under these assumptions an optimization algorithm is developed for SEAmodel updating to a transient test when external loads are harmonic step functions.This algorithm considers the response not only in a single frequency band,but also for several of them simultaneously.A damage index is defined that measures the change in the loss factor matrixwhen a damage has occurred at a certain location in the structure. The structuresconsidered in this study are built with damaged beam elements; as we are dealingwith the high frequency response, the numerical simulation is implemented witha Spectral Element Method. It has therefore been necessary to develop a spectralbeam damaged element as well. The reported results show that damage detectionis possible with this algorithm, moreover, damage location is also possible withina certain degree of accuracy.

Evapotranspiration of grapevine trained to a gable trellis system under netting and black plastic mulching

The evapotranspiration (ET c) of a table grape vineyard (Vitis vinifera, cv. Red Globe) trained to a gable trellis under netting and black plastic mulching was determined under semiarid conditions in the central Ebro River Valley during 2007 and 2008. The netting was made of high-density polyethylene (pores of 12 mm2) and was placed just above the ground canopy about 2.2 m above soil surface. Black plastic mulching was used to minimize soil evaporation. The surface renewal method was used to obtain values of sensible heat flux (H) from high-frequency temperature readings. Later, latent heat flux (LE) values were obtained by solving the energy balance equation. For the May–October period, seasonal ET c was about 843 mm in 2007 and 787 mm in 2008. The experimental weekly crop coefficients (K cexp) fluctuated between 0.64 and 1.2. These values represent crop coefficients adjusted to take into account the reduction in ET c caused by the netting and the black plastic mulching. Average K cexp values during mid- and end-season stages were 0.79 and 0.98, respectively. End-season K cexp was higher due to combination of factors related to the precipitation and low ET o conditions that are typical in this region during fall. Estimated crop coefficients using the Allen et al. (1998) approach adjusting for the effects of the netting and black plastic mulching (K cFAO) showed a good agreement with the experimental K cexp values.

Evapotranspiration and crop coefficients of rice (Oryza sativa L.) under sprinkler irrigation in a semiarid climate determined by the surface renewal method

The evapotranspiration (ETc) of sprinkler-irrigated rice was determined for the semiarid conditions of NE Spain during 2001, 2002 and 2003. The surface renewal method, after calibration against the eddy covariance method, was used to obtain values of sensible heat flux (H) from high-frequency temperature readings. Latent heat flux values were obtained by solving the energy balance equation. Finally, lysimeter measurements were used to validate the evapotranspiration values obtained with the surface renewal method. Seasonal rice evapotranspiration was about 750–800 mm. Average daily ETc for mid-season (from 90 to 130 days after sowing) was 5.1, 4.5 and 6.1 mm day−1 for 2001, 2002 and 2003, respectively. The experimental weekly crop coefficients fluctuated in the range of 0.83–1.20 for 2001, 0.81–1.03 for 2002 and 0.84–1.15 for 2003. The total growing season was about 150–160 days. In average, the crop coefficients for the initial (Kcini), mid-season (Kcmid) and late-season stages (Kcend) were 0.92, 1.06 and 1.03, respectively, the length of these stages being about 55, 45 and 25 days, respectively.

Biostimulation methods associated with early weaning and reproductive rhythms in primiparous rabbit does

El objetivo general de esta Tesis Doctoral ha sido tratar de mejorar los parámetros reproductivos de las conejas primíparas lactantes, empleando dos métodos de manejo (destete temprano y extensificación del ritmo reproductivo), que están directamente relacionados con su balance energético. Para ello, se diseñaron 2 experimentos en este tipo de hembras. En el primero, se estudió el efecto del destete a 25 días post-parto (dpp) sobre la actividad ovárica y el metabolismo energético de las conejas una semana más tarde (32 dpp). Un total de 34 primíparas lactantes con 8 gazapos fueron distribuidas en tres grupos: 10 conejas se sacrificaron a los 25 dpp (grupo L25), 13 fueron destetadas a los 25 dpp y sacrificadas a los 32 dpp (grupo NL32), y 11 conejas no se destetaron y fueron sacrificadas a los 32 dpp (grupo L32). No se observaron diferencias significativas entre grupos en el peso corporal, el peso del ovario, ni en las concentraciones séricas de ácidos grasos no esterificados y de proteínas totales. A pesar de que el grupo NL32 presentó un bajo consumo de alimento (122 ± 23,5 g / día, p <0,001), su contenido corporal estimado de lípidos (16,9 ± 1,09%, P <0,008), proteínas (19,7 ± 0,07%, P <0,0001), y energía (1147 ± 42,7 MJ / kg, p <0,006) fueron más elevados y las concentraciones séricas de glucosa (158 ± 24,5 mg/dl, p <0,04) más bajas que en los grupos L25 (11,9 ± 1,3%, 18,5 ± 0,08%, 942 ± 51,3 MJ/kg y 212 ± 27,9 mg/dl) y L32 (13,4 ± 1,03%, 18,5 ± 0,1%, 993 ± 40,4 MJ/kg y 259 ± 29,5 mg/dl), respectivamente. En el grupo L25 se observó un menor número medio de folículos ≥ 1 mm en la superficie ovárica en comparación con los grupos NL32 y L32 (12,7 ± 1,5 vs. 18,0 ± 1,45 y 17,6 ± 1,67, p <0,05). La población folicular ovárica en las secciones histológicas y la inmunolocalización de los receptores de prolactina fueron similares en todos los grupos. En el grupo L25, tanto la maduración nuclear de oocitos, medida en términos de tasas alcanzadas de Metafase II (67,0 vs. 79,7 y 78,3%, P <0.05) y la maduración citoplasmática, medida por el porcentaje de gránulos corticales (GC) total o parcialmente migrados en los oocitos, fueron significativamente menores que en los grupos NL32 y L32 (16,0 vs 38,3 y 60,0%, P <0.05). En conclusión, a pesar de que el destete precoz a 25 dpp pareció mejorar las reservas de energía de las conejas primíparas, este hecho no se reflejó claramente a nivel ovárico a los 32 dpp y fue similar independientemente del destete, por lo que éste último podría llevarse a cabo más tarde. En el segundo experimento, se compararon dos ritmos reproductivos. Se utilizaron un total de 48 conejas primíparas lactantes con 8 gazapos que se asignaron al azar en dos grupos experimentales: a) lactantes sacrificadas a comienzos del post-parto (11 dpp) de acuerdo a un ritmo semi-intensivo (n = 24), y b) lactantes sacrificadas al final del período post-parto (25 dpp) de acuerdo con un ritmo más extensivo (n = 24). En ellas, se estudió el peso vivo, la composición corporal estimada, parámetros metabólicos y endocrinos (estradiol y progesterona) y características ováricas como la población folicular y la tasa de atresia, así como la maduración nuclear y citoplásmica de los oocitos. En este estudio, el peso vivo, el contenido de energía corporal, los depósitos grasos y los ácidos grasos no esterificados disminuyeron a lo largo del post-parto con respecto al momento del parto (P <0,05). Las concentraciones séricas de proteínas y glucosa aumentaron en el mismo periodo post-parto (P <0,05). Se observaron similares niveles de estradiol y progesterona en ambos ritmos, así como una población folicular, tasas de maduración nuclear (tasa de oocitos en metafase II) y citoplasmática (porcentaje de oocitos con gránulos corticales migrados), similares en ambos momentos del post-parto. Sin embargo, el número de folículos preovulatorios en la superficie ovárica fue menor (P <0,05) y la tasa de atresia tendió a ser mayor con un porcentaje también menor de folículos sanos (P <0,1) en los ovarios de las hembras sometidas al ritmo extensivo. En conclusión, al final del post-parto (25 días), las conejas primíparas sin destetar muestran un deterioro de sus reservas corporales, de sus parámetros metabólicos séricos y de la calidad de sus oocitos; incluso se ha observado una ligera influencia negativa en el desarrollo de sus folículos ováricos. Por esta razón, se considera que en las conejas primíparas lactantes el manejo reproductivo extensivo (25 dpp) no presenta ninguna ventaja en comparación con el semi-intensivo (11 dpp). A la vista de los resultados de estos dos experimentos, podemos decir que ni el destete temprano, ni la extensificación del ritmo reproductivo han conseguido una mejora en los parámetros reproductivos de una hembra primípara. Por ello, son necesarios más estudios sobre el estado metabólico de la coneja primípara lactante para conseguir métodos o estrategias que lo mejoren y tengan consecuencias directas sobre la actividad reproductiva y sobre su éxito productivo. The general aim of this Thesis was to study two management methods (early weaning and extensive reproductive rhythm) linked to the energy balance of the primiparous rabbit does to improve their reproductive performance. In this sense, 2 experiments were conducted using this kind of females. In the first experiment, the effect of weaning at 25 days post-partum (dpp) on ovarian activity and energetic metabolism one week later (32 dpp) was studied. A total of 34 primiparous lactating rabbit does were used and distributed among three groups: 10 does euthanized at 25 dpp (group L25), 13 does weaned at 25 dpp and euthanized at 32 dpp (group NL32), and 11 non weaned does euthanized at 32 dpp (group L32). No significant differences were observed in live body weight, ovary weight, serum non esterified fatty acids (NEFA) and total protein concentration among groups. Although NL32 does had a low feed intake (122±23.5 g/Day; P < 0.001), their estimated lipids (16.9±1.09%, P < 0.008), protein (19.7±0.07%, P < 0.0001), and energy (1147±42.7 MJ/kg, P < 0.006) body contents were higher and their serum glucose concentrations (158±24.5 mg/dl, P < 0.04) were lower compared to L25 does (11.9±1.3%, 18.5±0.08%, 942±51.3 MJ/kg and 212±27.9 mg/dl) and L32 does (13.4±1.03%, 18.5±0.1%, 993±40.4 MJ/kg and 259±29.5 mg/dl, respectively). A lower number of follicles ≥1mm was observed compared to NL32 and L32 groups (12.7±1.5 vs. 18.0±1.45 and 17.6 ±1.67; P < 0.05) in the ovarian surface of L25 does. Follicular population in the histological ovarian sections and immunolocalization of prolactin receptor were similar in all groups. In group L25, both nuclear maturation of oocytes in terms of Metaphase II rate (67.0 vs. 79.7 and 78.3%; P < 0.05) and cytoplasmic maturation measured by percentage of cortical granules (CG), totally or partially migrated in oocytes were significantly lower than in groups NL32 and L32 (16.0 vs. 38.3 and 60.0%; P < 0.05). Consequently, a higher rate of oocytes with non-migrated CGs was found in group L25 than in groups NL32 and L32 (76.0 vs. 46.8 and 33.3%; P < 0.05). In conclusion, even though early weaning at 25 dpp seemed to improve body energy stored in primiparous does, this fact was not well reflected on the ovarian status at 32 dpp, which was similar regardless of weaning time. In the second experiment, two reproductive rhythms were compared. A total of 48 primiparous Californian x New Zealand White rabbit does suckling 8 kits were randomly allocated in two experimental groups: a) lactating does euthanized at early post-partum period (11 dpp) according to a semi-intensive rhythm (n = 24), and b) lactating does euthanized on later post-partum period (25 dpp) according to a more extensive rhythm (n = 24). Live weight, estimated body composition, serum metabolic and endocrine parameters (oestradiol and progesterone concentrations) and ovarian features like follicle population and atresia rate, and oocyte maturation were studied. Live weight, body energy content, lipid depots and serum non esterified fatty acids (NEFA) concentrations diminished from parturition time to post-partum period (P < 0.05). In addition, serum protein and glucose concentrations increased along postpartum time (P < 0.05). Similar oestradiol and progesterone levels were shown in rhythms as well as similar follicle population and nuclear and cytoplasmic maturation rates measured as metaphase II and cortical granule migration, respectively in both postpartum times. However, number of preovulatory follicles on the ovarian surface was lower (P < 0.05) and atresia rate tended to be higher with also lower percentage of healthy follicles (P < 0.1) in ovaries of females of extensive group. In conclusion, primiparous non-weaned rabbits does at late post-partum time (25 days), Did no show any improvement regarding body reserves, serum metabolic parameters and oocyte quality; even a slight negative influence has been observed in the development of their ovarian follicles. Thus this reproductive management does not present any advantage compared to earlier post-partum (11 days) reproductive rhythm. In summary, according to the obtained results from these two experiments, we can say that the application of early weaning and the extensive rhythms did not achieve an improvement in the reproductive performance of primiparous does. Thus, it is necessary to conduct more studies about the metabolic status of the primiparous lactating doe to achieve strategies in order to improve it and consequently, to improve the reproductive activity and their productive success.

Estudio energético comparativo de diferentes configuraciones de ciclo combinado

El objetivo del presente proyecto consiste en la modelización y optimización de una planta de gasificación integrada en ciclo combinado de 400 MW de potencia neta, mediante el uso del programa Cycle-Tempo, desarrollado por la Universidad de Delft. Para la modelización de la planta, se ha dividido en sus dos unidades principales: la isla de gasificación y el ciclo combinado. Para la validación del modelo de la isla de gasificación, se ha utilizado una composición de referencia de un combustible gasificable y se ha obtenido la composición del gas de síntesis esperada. Se han modelado y optimizado varias configuraciones de ciclo combinado, variando los parámetros característicos de la caldera de recuperación de calor. Se ha realizado la integración de las dos unidades para maximizar la potencia entregada por la planta. Finalmente, se ha estimado el balance anual de energía del ciclo combinado alimentado con gas natural y con el gas de síntesis, con el fin de comparar las rentabilidades económicas obtenidas. Mediante el estudio realizado, se deduce que la forma más eficiente de producir energía, a partir del uso del carbón, es la tecnología de gasificación integrada en ciclo combinado, pese a que su rendimiento sea inferior al ciclo combinado alimentado con gas natural. ABSTRACT The aim of this project is the modeling and optimization of an integrated gasification combined cycle plant of 400 MW net power, using the Cycle-Tempo program, developed by the University of Delft. For the modeling of the plant, it has been divided into its two main units: the island of gasification and the combined cycle. For the model validation of the gasification island, a reference composition of a gasifiable fuel has been used and the expected synthesis gas composition was obtained. Several configurations of combined cycle have been modeled and optimized by varying the characteristic parameters of the heat recovery steam generator. It has made the integration of the two units to reach maximum optimization of power, which has been delivered by the plant. Finally, it has been estimated the annual energy balance for the combined cycle plant fueled with natural gas and with syngas, in order to compare the profitability obtained with each one. Through the study, it is deduced that the most efficient way to produce energy from the use of coal, is the integrated gasification combined cycle technology, although their performance is lower than that obtained from the combined cycle fueled with natural gas.

Nutrition and physical activity programs for obesity treatment (PRONAF study). methodological approach of the project

Este trabajo aborda la metodología seguida para llevar a cabo el proyecto de investigación PRONAF (Clinical Trials Gov.: number NCT01116856.) Background: At present, scientific consensus exists on the multifactorial etiopatogenia of obesity. Both professionals and researchers agree that treatment must also have a multifactorial approach, including diet, physical activity, pharmacology and/or surgical treatment. These two last ones should be reserved for those cases of morbid obesities or in case of failure of the previous ones. The aim of the PRONAF study is to determine what type of exercise combined with caloric restriction is the most appropriate to be included in overweigth and obesity intervention programs, and the aim of this paper is to describe the design and the evaluation methods used to carry out the PRONAF study. Methods/design: One-hundred nineteen overweight (46 males) and 120 obese (61 males) subjects aged 18–50 years were randomly assigned to a strength training group, an endurance training group, a combined strength + endurance training group or a diet and physical activity recommendations group. The intervention period was 22 weeks (in all cases 3 times/wk of training for 22 weeks and 2 weeks for pre and post evaluation). All subjects followed a hypocaloric diet (25-30% less energy intake than the daily energy expenditure estimated by accelerometry). 29–34% of the total energy intake came from fat, 14–20% from protein, and 50–55% from carbohydrates. The mayor outcome variables assesed were, biochemical and inflamatory markers, body composition, energy balance, physical fitness, nutritional habits, genetic profile and quality of life. 180 (75.3%) subjects finished the study, with a dropout rate of 24.7%. Dropout reasons included: personal reasons 17 (28.8%), low adherence to exercise 3 (5.1%), low adherence to diet 6 (10.2%), job change 6 (10.2%), and lost interest 27 (45.8%). Discussion: Feasibility of the study has been proven, with a low dropout rate which corresponds to the estimated sample size. Transfer of knowledge is foreseen as a spin-off, in order that overweight and obese subjects can benefit from the results. The aim is to transfer it to sports centres. Effectiveness on individual health-related parameter in order to determine the most effective training programme will be analysed in forthcoming publications.

Estudio Energético y de Explotación de diferentes conjuntos de Labranza para el Cultivo de la Yuca (Manihot esculenta, Crantz) en un Fluvisol

El trabajo se desarrolló en tres etapas de investigación, las dos primeras fueron realizadas en la Unidad Básica de Producción Cooperativa “El Palmar” perteneciente a la Empresa de Cultivos Varios "Paquito Rosales Benítez" del municipio de Yara, provincia de Granma, Cuba, el cual se llevó a cabo en el período de abril de 2005 a enero de 2008; y de noviembre de 2012 a febrero de 2013 respectivamente; la tercera se ejecutó de mayo a junio de 2013 en un canal de suelo ubicado en la nave de maquinaria del Departamento de Ingeniería Rural de la Universidad Politécnica de Madrid. En la primera etapa se evaluaron los conjuntos tractor-apero que intervienen en la realización de cuatro sistemas de labranza para el cultivo de la yuca, variedad Enana Rosada. Los sistemas de laboreo fueron: T1, labor de aradura (alzado) con un arado de discos seguidas de un pase de grada de discos un pase cruzado de un escarificador y un pase con una grada de discos (5 labores); T2, laboreo mínimo que comprende una labor profunda con un escarificador con saetas seguido por una labor de grada de discos (2 labores); T3, laboreo mínimo en el que se realizaron dos pases cruzados con escarificador y una labor de fresado con una fresadora de eje horizontal (3 labores) y; T4, dos labores cruzadas con la grada de discos seguidas por otras dos pases cruzados con el escarificador y una última labor con la grada de discos (5 labores). Se realizaron cinco observaciones de la jornada laboral para cada uno de los conjuntos tractorapero de cada sistema de laboreo en tres campañas, evaluando el consumo de combustible, las diferentes productividades, los índices y coeficientes tecnológicos y de explotación, el rendimiento del cultivo el balance energético del mismo, y la emisión de CO2 equivalente. En la segunda etapa se determinó la fuerza de tiro requerida por un órgano de trabajo de un escarificador con saetas en condiciones de campo, en tres profundidades (15, 25 y 35 cm) y a cuatro velocidades de trabajo (1,30; 1,49; 1,65 y 2,32 m s-1). En la tercera etapa se determinaron las fuerzas horizontales y verticales en una maqueta experimental de un órgano de trabajo de un escarificador con saetas (1:5 del tamaño real del apero) en cuatro contenidos de humedad (60, 90, 120 y 150 g kg-1), tres densidades del suelo (1,1; 1,2 y 1,3 Mg m-3) y una velocidad de 40 mm s-1. Se comparan los resultados del apero a tamaño real y la maqueta experimental. Los mejores resultados relacionados con los indicadores evaluados a la maquinaria correspondieron al sistema de laboreo mínimo T2, el cual presenta la mejor productividad por hora de tiempo limpio (1,34 ha h-1) y de tiempo operativo (1,27 ha h-1), con diferencias significativas respecto al resto de los sistemas de labranza evaluados; así como el menor consumo de combustible (32,4 L ha-1) y el mejor comportamiento energético, con diferencias significativas respecto a las demás, resultando inferior en un 63, 30 y 58 % con relación a T1, T3 y T4. La fuerza de tiro del órgano de trabajo del escarificador con saetas se incrementa con la densidad del suelo y con la profundidad, y velocidad de trabajo. Las fuerzas horizontales y verticales de la maqueta se incrementan linealmente con la densidad y humedad del suelo. Existe una relación lineal entre las fuerzas de tiro y horizontales medidas en el apero real y en el apero a escala con el contenido de humedad del suelo. ABSTRACT The work was developed in three stages of research, the first two were conducted in the Basic Unit of Cooperative Production "El Palmar" belonging to the agricultural farm "Paquito Rosales Benitez" in the municipality of Yara, Granma Province, Cuba, the which was conducted in the period from April 2005 to January 2008 and November 2012 and February 2013 respectively, the third from May to June 2013 on a soilbin located in the ship's machinery of Rural Engineering Department of the Technical University of Madrid. In the first stage were evaluated tractor-implement sets involved in the completion of four tillage systems for cassava, Pink Dwarf variety. Tillage systems were: T1, plowing (elevation) with a disk plow followed by a pass of disc harrow, a cross of scarifier and a pass with a disc harrow (5 labours), T2, minimum tillage comprising a deep work with a scarifier with a bolt followed by a disc harrow work (two labours); T3, minimum tillage which two crossed passes performed with scarifier and milling labour with a horizontal axis milling machine (three labours) and, T4, two crossed labours with disc harrow followed by two crossed passes with the scarifier and a final labour with disc harrow (5 labours). Five observations of the working day for each tractor-implement sets of each tillage system in three seasons were performed, evaluating fuel consumption, different productivities, indexes and technological and operational factors, the crop yield energy balance and the emission of CO2 equivalent. In the second stage we determined the draft force required by a working body of a scarifier with bolt under field conditions at three depths (15, 25 and 35 cm) and four operating speeds (1.30, 1.49 , 1.65 and 2.32 m s-1). In the third stage were determined horizontal and vertical forces on an experimental model of a working body of a scarifier with bolt (1:5 real scale of the implement) in four moisture contents (60, 90, 120 and 150 g kg -1), three soil densities (1.1, 1.2, and 1.3 Mg m-3) and a speed of 40 mm s-1.The results of real scale implement the experimental model were compared. The best results related to evaluated machinery indicators corresponded to T2 minimum tillage system, which presents the best productivity per hour clean time (1.34 ha h-1) and operating time (1.27 ha h-1), with significant differences compared to other tillage systems evaluated; as well as lower fuel consumption (32.4 L ha-1) and the best energy performance, with significant differences from the other, resulting lower by 63, 30 and 58% compared to T1, T3 and T4. The draft force of the working body of the scarifier with bolt increases with soil density and depth, and speed of work. The horizontal and vertical forces of the model increase linearly with density and soil moisture. A linear relationship exists between the shot and horizontal forces measured at the real implement and scale implement with the soil moisture content.