In situ acoustic methods to estimate the physical and mechanical aging of oriented strand board

Following the success achieved in previous research projects usin non-destructive methods to estimate the physical and mechanical aging of particle and fibre boards, this paper studies the relationships between aging, physical and mechanical changes, using non-destructive measurements of oriented strand board (OSB). 184 pieces of OSB board from a French source were tested to analyze its actual physical and mechanical properties. The same properties were estimated using acoustic non-destructive methods (ultrasound and stress wave velocity) during a physical laboratory aging test. Measurements were recorded of propagation wave velocity with the sensors aligned, edge to edge, and forming an angle of 45 degrees, with both sensors on the same face of the board. This is because aligned measures are not possible on site. The velocity results are always higher in 45 degree measurements. Given the results of statistical analysis, it can be concluded that there is a strong relationship between acoustic measurements and the decline in physical and mechanical properties of the panels due to aging. The authors propose several models to estimate the physical and mechanical properties of board, as well as their degree of aging. The best results are obtained using ultrasound, although the difference in comparison with the stress wave method is not very significant. A reliable prediction of the degree of deterioration (aging) of board is presented.

Characterization of Amorphous Tantalum Oxide for Insulating Acoustic Mirrors

This work describes the assessment of the acoustic properties of sputtered tantalum oxide films intended as high impedance films for the acoustic isolation of bulk acoustic wave devices operating in the GHz frequency range. The films are grown by sputtering a metallic tantalum target under different oxygen and argon gas mixtures, total pressures, pulsed DC powers and substrate bias. The structural properties of the films are assessed through infrared absorption spectroscopy and X-ray diffraction measurements. Their acoustic impedance is obtained after estimating the mass density by X-ray reflectometry measurements and the longitudinal acoustic velocity by analyzing the longitudinal λ/2 resonance induced in a tantalum oxide film inserted between an acoustic reflector and an AlN-based resonator. A second measurement of the sound velocity is achieved through picosecond acoustic spectroscopy.

Ta2O5/SiO2 insulating acoustic mirrors for AlN-based X-band BAW resonators

This work describes the performance of AlN-based bulk acoustic wave resonators built on top of insulating acoustic reflectors and operating at around 8 GHz. The acoustic reflectors are composed of alternate layers of amorphous Ta2O5and SiO2 deposited at room temperature by pulsed-DC reactive sputtering in Ar/O2 atmospheres. SiO2 layers have a porous structure that provides a low acoustic impedance of only 9.5 MRayl. Ta2O5 films exhibit an acoustic impedance of around 39.5 MRayl that was assessed by the picoseconds acoustic technique These values allow to design acoustic mirrors with transmission coefficients in the centre of the band lower than -40 dB (99.998 % of reflectance) with only seven layers. The resonators were fabricated by depositing a very thin AlN film onto an iridium bottom electrode 180 nm-thick and by using Ir or Mo layers as top electrode. Resonators with effective electromechanical coupling factors of 5.7% and quality factors at the antiresonant frequency around 600 are achieved.

Acoustic displacement triangle based on the individual element test

A three node, displacement based, acoustic element is developed. In order to avoid spurious rotational modes, a higher order stiffness is introduced. The higher order stiffness is developed from an incompatible strain field which computes element volume changes under nodal rotational displacements fields. The higher order strain satisfies the IET requirements, non affecting convergence. The higher order stiffness is modulated, element by element, with a factor. Thus, the displacement based formulation is capable of placing the spurious rotational modes over the range of physical compressional modes that can be accurately captured by the mesh.

The effect of acoustic screens on orchestra musicians

La Directiva 2003/10/CE del Parlamento Europeo y del Consejo, del 6 de febrero de 2003, específica con arreglo al apartado 1 del artículo 16 de la Directiva 89/391/CEE las disposiciones mínimas de seguridad y de salud relativas a la exposición de los trabajadores a los riesgos derivados de los agentes físicos (ruido). En la industria musical, y en concreto en los músicos de orquesta, una exposición de más de ocho horas al día a un nivel de presión sonora de 80dB(A) o más es algo muy común. Esta situación puede causar a los trabajadores daños auditivos como la hiperacusia, hipoacusia, tinitus o ruptura de la membrana basilar entre otros. Esto significa que deben tomarse medidas para implementar las regulaciones de la forma más razonable posible para que la interpretación del músico, la dinámica y el concepto musical que se quiere transmitir al público se vea lo menos afectada posible. Para reducir la carga auditiva de los músicos de orquesta frente a fuertes impactos sonoros provenientes de los instrumentos vecinos, se está investigando sobre el uso de unos paneles acústicos que colocados en puntos estratégicos de la orquesta pueden llegar a reducir el impacto sonoro sobre el oído hasta 20dB. Los instrumentos de viento metal y de percusión son los responsables de la mayor emisión de presión sonora. Para proteger el oído de los músicos frente a estos impactos, se colocan los paneles en forma de barrera entre dichos instrumentos y los músicos colocados frente a ellos. De esta forma se protege el oído de los músicos más afectados. Para ver el efecto práctico que producen estos paneles en un conjunto orquestal, se realizan varias grabaciones en los ensayos y conciertos de varias orquestas. Los micrófonos se sitúan a la altura del oído y a una distancia de no más de 10cm de la oreja de varios de los músicos más afectados y de los músicos responsables de la fuerte emisión sonora. De este modo se puede hacer una comparación de los niveles de presión sonora que percibe cada músico y evaluar las diferencias de nivel existentes entre ambos. Así mismo se utilizan configuraciones variables de los paneles para comparar las diferencias de presión sonora que existen entre las distintas posibilidades de colocarlos y decidir así sobre la mejor ubicación y configuración de los mismos. A continuación, una vez obtenidos las muestras de audio y los diferentes archivos de datos medidos con un analizador de audio en distintas posiciones de la orquesta, todo ello se calibra y analiza utilizando un programa desarrollado en Matlab, para evaluar el efecto de los paneles sobre la percepción auditiva de los músicos, haciendo especial hincapié en el análisis de las diferencias de nivel de presión sonora (SPL). Mediante el cálculo de la envolvente de las diferencias de nivel, se evalúa de un modo estadístico el efecto de atenuación de los paneles acústicos en los músicos de orquesta. El método está basado en la probabilidad estadística de varias muestras musicales ya que al tratarse de música tocada en directo, la dinámica y la sincronización entre los músicos varía según el momento en que se toque. Estos factores junto con el hecho de que la partitura de cada músico es diferente dificulta la comparación entre dos señales grabadas en diferentes puntos de la orquesta. Se necesita por lo tanto de varias muestras musicales para evaluar el efecto de atenuación de los paneles en las distintas configuraciones mencionadas anteriormente. El estudio completo del efecto de los paneles como entorno que influye en los músicos de orquesta cuando están sobre el escenario, tiene como objetivo la mejora de sus condiciones de trabajo. Abstract For several years, the European Union has been adopting many laws and regulations to protect and give more security to people who are exposed to some risk in their job. Being exposed to a loud sound pressure level during many hours in the job runs the risk of hearing damage. Particularly in the field of music, the ear is the most important working tool. Not taking care of the ear can cause some damage such as hearing loss, tinnitus, hyperacusis, diplacusis, etc. This could have an impact on the efficiency and satisfaction of the musicians when they are playing, which could also cause stress problems. Orchestra musicians, as many other workers in this sector, are usually exposed to a sound level of 80dB(A) or more during more than eight hours per day. It means that they must satisfy the law and their legal obligations to avoid health problems proceeding from their job. Putting into practice the new regulations is a challenge for orchestras. They must make sure that the repertoire, with its dynamic, balance and feeling, is not affected by the reduction of sound levels imposed by the law. This study tries to investigate the benefits and disadvantages of using shields as a hearing protector during rehearsals and orchestral concerts.

Acoustic properties of microperforated panels and their optimizatión by simulated annealing

This thesis investigates the acoustic properties of microperforated panels as an alternative to passive noise control. The first chapters are devoted to the review of analytical models to obtain the acoustic impedance and absorption coefficient of perforated panels. The use of panels perforated with circular holes or with slits is discussed. The theoretical models are presented and some modifications are proposed to improve the modeling of the physical phenomena occurring at the perforations of the panels. The absorption band is widened through the use of multiple layer microperforated panels and/or the combination of a millimetric panel with a porous layer that can be a fibrous material or a nylon mesh. A commercial micrometric mesh downstream a millimetric panel is proposed as a very efficient and low cost solution for controlling noise in reduced spaces. The simulated annealing algorithm is used in order to optimize the panel construction to provide a maximum of absorption in a determined wide band frequency range. Experiments are carried out at normal sound incidence and plane waves. One example is shown for a double layer microperforated panel subjected to grazing flow. A good agreement is achieved between the theory and the experiments. RESUMEN En esta tesis se investigan las propiedades acústicas de paneles micro perforados como una alternativa al control pasivo del ruido. Los primeros capítulos están dedicados a la revisión de los modelos de análisis para obtener la impedancia acústica y el coeficiente de absorción de los paneles perforados. El uso de paneles perforados con agujeros circulares o con ranuras es discutido. Se presentan diferentes modelos y se proponen algunas modificaciones para mejorar la modelización de los fenómenos físicos que ocurren en las perforaciones. La banda de absorción se ensancha a través del uso de capas múltiples de paneles micro perforados y/o la combinación de un panel de perforaciones milimétricas combinado con una capa porosa que puede ser un material fibroso o una malla de nylon. Se propone el uso de una malla micrométrica detrás de un panel milimétrico como una solución económica y eficiente para el control del ruido en espacios reducidos. El algoritmo de recocido simulado se utiliza con el fin de optimizar la construcción de paneles micro perforados para proporcionar un máximo de absorción en una banda determinada frecuencias. Los experimentos se llevan a cabo en la incidencia normal de sonido y ondas planas. Se muestra un ejemplo de panel micro perforado de doble capa sometido a flujo rasante. Se consigue un buen acuerdo entre la teoría y los experimentos.

High-Acoustic-Impedance Tantalum Oxide Layers for Insulating Acoustic Reflectors

This work describes the assessment of the acoustic properties of sputtered tantalum oxide films intended for use as high-impedance films of acoustic reflectors for solidly mounted resonators operating in the gigahertz frequency range. The films are grown by sputtering a metallic tantalum target under different oxygen and argon gas mixtures, total pressures, pulsed dc powers, and substrate biases. The structural properties of the films are assessed through infrared absorption spectroscopy and X-ray diffraction measurements. Their acoustic impedance is assessed by deriving the mass density from X-ray reflectometry measurements and the acoustic velocity from picosecond acoustic spectroscopy and the analysis of the frequency response of the test resonators.

Influence of Crystal Quality on the Excitation and Propagation of Surface and Bulk Acoustic Waves in Polycrystalline AlN Films

We investigate the excitation and propagation of acoustic waves in polycrystalline aluminum nitride films along the directions parallel and normal to the c-axis. Longitudinal and transverse propagations are assessed through the frequency response of surface acoustic wave and bulk acoustic wave devices fabricated on films of different crystal qualities. The crystalline properties significantly affect the electromechanical coupling factors and acoustic properties of the piezoelectric layers. The presence of misoriented grains produces an overall decrease of the piezoelectric activity, degrading more severely the excitation and propagation of waves traveling transversally to the c-axis. It is suggested that the presence of such crystalline defects in c-axis-oriented films reduces the mechanical coherence between grains and hinders the transverse deformation of the film when the electric field is applied parallel to the surface.

Calculus of the uncertainty in acoustic field measurements: comparative study between the uncertainty propagation method and the distribution propagation method

The new Spanish Regulation in Building Acoustic establishes values and limits for the different acoustic magnitudes whose fulfillment can be verify by means field measurements. In this sense, an essential aspect of a field measurement is to give the measured magnitude and the uncertainty associated to such a magnitude. In the calculus of the uncertainty it is very usual to follow the uncertainty propagation method as described in the Guide to the expression of Uncertainty in Measurements (GUM). Other option is the numerical calculus based on the distribution propagation method by means of Monte Carlo simulation. In fact, at this stage, it is possible to find several publications developing this last method by using different software programs. In the present work, we used Excel for the Monte Carlo simulation for the calculus of the uncertainty associated to the different magnitudes derived from the field measurements following ISO 140-4, 140-5 and 140-7. We compare the results with the ones obtained by the uncertainty propagation method. Although both methods give similar values, some small differences have been observed. Some arguments to explain such differences are the asymmetry of the probability distributions associated to the entry magnitudes,the overestimation of the uncertainty following the GUM

Influence of loudspeaker directivity on the measurement uncertainty of the acoustic testing of facades.

One of the most significant aspects of a building?s acoustic behavior is the airborne sound insulation of the room façades, since this determines the protection of its inhabitants against environmental noise. For this reason, authorities in most countries have established in their acoustic regulations for buildings the minimum value of sound insulation that must be respected for façades. In order to verify compliance with legal requirements it is usual to perform acoustic measurements in the finished buildings and then compare the measurement results with the established limits. Since there is always a certain measurement uncertainty, this uncertainty must be calculated and taken into account in order to ensure compliance with specifications. The most commonly used method for measuring sound insulation on façades is the so-called Global Loudspeaker Method, specified in ISO 140-5:1998. This method uses a loudspeaker placed outside the building as a sound source. The loudspeaker directivity has a significant influence on the measurement results, and these results may change noticeably by choosing different loudspeakers, even though they all fulfill the directivity requirements of ISO 140-5. This work analyzes the influence of the loudspeaker directivity on the results of façade sound insulation measurement, and determines its contribution to measurement uncertainty. The theoretical analysis is experimentally validated by means of an intermediate precision test according to ISO 5725-3:1994, which compares the values of sound insulation obtained for a façade using various loudspeakers with different directivities. Keywords: Uncertainty, Façade, Insulation

Simulation, construction and characterization of a piezoelectric transducer using rexolite as acoustic matching

This article describes the simulation and characterization of an ultrasonic transducer using a new material called Rexolite to be used as a matching element. This transducer was simulated using a commercial piezoelectric ceramic PIC255 at 8 MHz. Rexolite, the new material, presents an excellent acoustic matching, specially in terms of the acoustic impedance of water. Finite elements simulations were used in this work. Rexolite was considered as a suitable material in the construction of the transducer due to its malleability and acoustic properties, to validate the simulations a prototype transducer was constructed. Experimental measurements were used to determine the resonance frequency of the prototype transducer. Simulated and experimental results were very similar showing that Rexolite may be an excellent matching, particularly for medical applications.

Transient acoustic response in car cabins with localization of reflections

Due to its small size and the restrictions on source and listener positions, the design of sound reproduction systems for car cabins is particularly cumbersome. In the present project the measurement of the impulse response between a single loudspeaker and a listener position, with special emphasis on the directional characteristics, will be examined. The propagation paths inside a car are very short, meaning that it is very difficult for the existing commercial measurement systems to resolve the different reflections arriving to the listener. This paper propose a first approach of an algorithm based on time difference of arrival along a measurement technique aiming at finding the reflections and their direction of arrival to the listener. To this end a circular microphone array at a known position is employed, along with Maximum-Length Sequences (MLS) measurement technique. The results are processed so as to extract the directional properties, demonstrate the physical limitations that can influence or prevent this detection in practice. Measurements were carried out in a free-field environment (anechoic chamber) making use of different panels closer around the microphone array. RESUMEN. El diseño de sistemas de reproducción de audio para cabinas de coche es especialmente complicado debido al reducido tamaño del espacio y las restricciones de los altavoces y posiciones de escucha de los ocupantes. En el presente proyecto, se examinan mediciones de la respuesta al impulso entre un altavoz y una posición de escucha con especial énfasis en las características direccionales. Los caminos de propagación de las ondas sonoras dentro de un coche son muy cortos, lo que hace difícil para los instrumentos de medida existentes en el mercado determinar las direcciones de llegada de las diferentes reflexiones que llegan a una posición de escucha. Este trabajo propone una primera aproximación de un algoritmo, basado en las diferencias temporales de llegada de una onda a diferentes puntos de medida, y una particular técnica de medida de la respuesta al impulso para obtener las direcciones de llegada de reflexiones a una posición de escucha. Para ello, se emplea una matriz circular de micrófonos en una posición conocida junto con la técnica de medida MLS (Maximum Length Sequence). Los resultados obtenidos son procesados para extraer la dirección de llegada de las reflexiones acústicas y encontrar las limitaciones que influyan en la detección de dichas reflexiones. Las mediciones se llevan a cabo en un entorno de campo libre y utilizando diferentes superficies reflectantes alrededor de la matriz de micrófonos.

Acoustic characterisation of cinema screens

As a consequence of cinema screens being placed in front of screen-speakers, a reduction in sound quality has been noticed. Cinema screens not only let the sound go through them, but also absorb a small amount of it and reflect the sound which impacts on the screen to the back, coming forward again in case it impacts on the loudspeaker. This backwards reflection in addition to the signal coming from the loudspeaker can lead to constructive or destructive interference at certain frequencies which usually results in comb filtering. In this project, this effect has been studied through researching amongst various data sheet provided by different manufacturers, acoustical measurements completed in the large anechoic chamber of the ISVR and some theoretical models developed with MatLab software. If results obtained with MatLab are accurate enough in comparison to the real measurements taken in the anechoic chamber this would lead to a good way to predict which would be the attenuation added to the system at each frequency, given that not all manufacturers provide an attenuation curve, but only an average attenuation. This average attenuation might be useless as sound waves have different wavelengths and its propagation through partitions varies. In fact, sound is composed by high and low frequencies, where high frequencies are characterised by a small wavelength which is usually easier to attenuate than low frequencies that characterised by bigger wavelengths. Furthermore, this information would be of great value to both screen manufacturers, who could offer a much more precise data in their data sheets; and customers, who would have a great amount of information to their disposal before purchasing and installing anything in their cinemas, being able to know by themselves which screen or loudspeaker should be best to meet their expectative. RESUMEN. La aparición de la digitalización de las bandas sonoras para las películas hace posible la mejora en la calidad de sonido de los cines. Sin embargo, un aspecto a tener en cuenta en esta calidad del sonido es la transmisión de éste a través de la pantalla, ya que normalmente tras ella se encuentran situados los altavoces. Las propiedades acústicas varían dependiendo del tipo de pantalla que se utilice, además de haber poca información a la que acceder para poder valorar su comportamiento. A lo largo de este proyecto, se analizan tres muestras de pantallas distintas donadas por distintos fabricantes para poder llegar a la conclusión de dependiendo del tipo de pantalla cuál es la distancia óptima a la que localizar la pantalla respecto al altavoz y con qué inclinación. Dicho análisis se realizó en la cámara anecoica del ISVR (University of Southampton) mediante la construcción de un marco de madera de 2x2 m en el que tensar las pantallas de cine, y un altavoz cuyo comportamiento sea el más similar al de los altavoces de pantalla reales. Los datos se captaron mediante cuatro micrófonos colocados en posiciones distintas y conectados al software Pulse de Brüel & Kjær, a través del cual se obtuvieron las respuestas en frecuencia del altavoz sin pantalla y con ella a diferentes distancias del altavoz. Posteriormente, los datos se analizaron con MatLab donde se calculó la atenuación, el factor de transmisión de la presión (PTF) y el análisis cepstrum. Finalmente, se realizó un modelo teórico del comportamiento de las pantallas perforadas basado en las placas perforadas utilizadas para atenuar el sonido entre distintas habitaciones. Como conclusión se llegó a que las pantallas curvadas son acústicamente más transparentes que las pantallas perforadas que a partir de 6 kHz son más acústicamente opacas. En las pantallas perforadas la atenuación depende del número de perforaciones por unidad de área y el diámetro de éstas. Dicha atenuación se reducirá si se reduce el diámetro de las perforaciones de la pantalla, o si se incrementa la cantidad de perforaciones. Acerca del efecto filtro peine, para obtener la mínima amplitud de éste la pantalla se deberá situar a una distancia entre 15 y 30 cm del altavoz, encontrando a la distancia de 30 cm que la última reflexión analizada a través de Cepstrum llega 5 ms más tarde que la señal directa, por lo cual no debería dañar el sonido ni la claridad del habla.

3-dimensional binaural sound rendering using acoustic measurements stored in the SOFA format

Several groups all over the world are researching in several ways to render 3D sounds. One way to achieve this is to use Head Related Transfer Functions (HRTFs). These measurements contain the Frequency Response of the human head and torso for each angle. Some years ago, was only possible to measure these Frequency Responses only in the horizontal plane. Nowadays, several improvements have made possible to measure and use 3D data for this purpose. The problem was that the groups didn't have a standard format file to store the data. That was a problem when a third part wanted to use some different HRTFs for 3D audio rendering. Every of them have different ways to store the data. The Spatially Oriented Format for Acoustics or SOFA was created to provide a solution to this problem. It is a format definition to unify all the previous different ways of storing any kind of acoustics data. At the moment of this project they have defined some basis for the format and some recommendations to store HRTFs. It is actually under development, so several changes could come. The SOFA[1] file format uses a numeric container called netCDF[2], specifically the Enhaced data model described in netCDF 4 that is based on HDF5[3]. The SoundScape Renderer (SSR) is a tool for real-time spatial audio reproduction providing a variety of rendering algorithms. The SSR was developed at the Quality and Usability Lab at TU Berlin and is now further developed at the Institut für Nachrichtentechnik at Universität Rostock [4]. This project is intended to be an introduction to the use of SOFA files, providing a C++ API to manipulate them and adapt the binaural renderer of the SSR for working with the SOFA format. RESUMEN. El SSR (SoundScape Renderer) es un programa que está siendo desarrollado actualmente por la Universität Rostock, y previamente por la Technische Universität Berlin. El SSR es una herramienta diseñada para la reproducción y renderización de audio 2D en tiempo real. Para ello utiliza diversos algoritmos, algunos orientados a sistemas formados por arrays de altavoces en diferentes configuraciones y otros algoritmos diseñados para cascos. El principal objetivo de este proyecto es dotar al SSR de la capacidad de renderizar sonidos binaurales en 3D. Este proyecto está centrado en el binaural renderer del SSR. Este algoritmo se basa en el uso de HRTFs (Head Related Transfer Function). Las HRTFs representan la función de transferencia del sistema formado por la cabeza y el torso del oyente. Esta función es medida desde diferentes ángulos. Con estos datos el binaural renderer puede generar audio en tiempo real simulando la posición de diferentes fuentes. Para poder incluir una base de datos con HRTFs en 3D se ha hecho uso del nuevo formato SOFA (Spatially Oriented Format for Acoustics). Este nuevo formato se encuentra en una fase bastante temprana de su desarrollo. Está pensado para servir como formato estándar para almacenar HRTFs y cualquier otro tipo de medidas acústicas, ya que actualmente cada laboratorio cuenta con su propio formato de almacenamiento y esto hace bastante difícil usar varias bases de datos diferentes en un mismo proyecto. El formato SOFA hace uso del contenedor numérico netCDF, que a su vez esta basado en un contenedor más básico llamado HRTF-5. Para poder incluir el formato SOFA en el binaural renderer del SSR se ha desarrollado una API en C++ para poder crear y leer archivos SOFA con el fin de utilizar los datos contenidos en ellos dentro del SSR.

Influence of loudspeaker directivity and measurement geometry on direct acoustic levels over façades for acoustic insulation tests with the International Standard ISO 140-5

The International Standard ISO 140-5 on field measurements of airborne sound insulation of façades establishes that the directivity of the measurement loudspeaker should be such that the variation in the local direct sound pressure level (ΔSPL) on the sample is ΔSPL < 5 dB (or ΔSPL < 10 dB for large façades). This condition is usually not very easy to accomplish nor is it easy to verify whether the loudspeaker produces such a uniform level. Direct sound pressure levels on the ISO standard façade essentially depend on the distance and directivity of the loudspeaker used. This paper presents a comprehensive analysis of the test geometry for measuring sound insulation and explains how the loudspeaker directivity, combined with distance, affects the acoustic level distribution on the façade. The first sections of the paper are focused on analysing the measurement geometry and its influence on the direct acoustic level variations on the façade. The most favourable and least favourable positions to minimise these direct acoustic level differences are found, and the angles covered by the façade in the reference system of the loudspeaker are also determined. Then, the maximum dimensions of the façade that meet the conditions of the ISO 140-5 standard are obtained for the ideal omnidirectional sound source and the piston radiating in an infinite baffle, which is chosen as the typical radiation pattern for loudspeakers. Finally, a complete study of the behaviour of different loudspeaker radiation models (such as those usually utilised in the ISO 140-5 measurements) is performed, comparing their radiation maps on the façade for searching their maximum dimensions and the most appropriate radiation configurations.