Electronic Steering antenna onboard for satellite communications in X band.

The antenna presented in this article will be developed for satellite communications onboard systems based on the recommendations ITU-R S.580-6 and ITU-R S.465-5. The antenna consists of printed elements grouped in an array, this terminal works in a frequency band from 7.25 up to 8.4 GHz (14.7% of bandwidth), where both bands, reception (7.25 - 7.75 GHz) and transmission (7.9 - 8.4 GHz), are included simultaneously. The antenna reaches a gain about 31 dBi, and it has a radiation pattern with a beamwidth smaller than 10° and a dual circular polarization. The antenna has the capability to steer in elevation from 90° to 40° electronically and 360° in azimuth with a motorized junction.

Mutual Coupling Reduction Techniques in Electronic Steering Antennas in X Band

This work provides the development of an antenna for satellite communications onboard systems based on the recommendations ITU-R S.580-6 [1] and ITU-R S.465-5 [2]. The antenna consists of printed elements grouped in an array, working in a frequency band from 7.25 up to 8.4 GHz (15% of bandwidth). In this working band, transmission and reception are included simultaneously. The antenna reaches a gain about 31 dBi, has a radiation pattern with a beam width smaller than 10oand dual circular polarization. It has the capability to steer in elevation through a Butler matrix to 45

Low-Profile Dual Circularly Polarized Antenna Array for Satellite Communications in the X Band

A planar antenna is introduced that works as a portable system for X-band satellite communications. This antenna is low-profile and modular with dimensions of 40 × 40 × 2.5 × cm. It is composed of a square array of 144 printed circuit elements that cover a wide bandwidth (14.7%) for transmission and reception along with dual and interchangeable circular polarization. A radiation efficiency above 50% is achieved by a low-loss stripline feeding network. This printed antenna has a 3 dB beamwidth of 5°, a maximum gain of 26 dBi and an axial ratio under 1.9 dB over the entire frequency band. The complete design of the antenna is shown, and the measurements are compared with simulations to reveal very good agreement.

Ta2O5/SiO2 insulating acoustic mirrors for AlN-based X-band BAW resonators

This work describes the performance of AlN-based bulk acoustic wave resonators built on top of insulating acoustic reflectors and operating at around 8 GHz. The acoustic reflectors are composed of alternate layers of amorphous Ta2O5and SiO2 deposited at room temperature by pulsed-DC reactive sputtering in Ar/O2 atmospheres. SiO2 layers have a porous structure that provides a low acoustic impedance of only 9.5 MRayl. Ta2O5 films exhibit an acoustic impedance of around 39.5 MRayl that was assessed by the picoseconds acoustic technique These values allow to design acoustic mirrors with transmission coefficients in the centre of the band lower than -40 dB (99.998 % of reflectance) with only seven layers. The resonators were fabricated by depositing a very thin AlN film onto an iridium bottom electrode 180 nm-thick and by using Ir or Mo layers as top electrode. Resonators with effective electromechanical coupling factors of 5.7% and quality factors at the antiresonant frequency around 600 are achieved.

Modular Planar Antenna at X-band for satellite communications

An antenna which has been conceived as a portable system for satellite communications based on the recommendations ITU-R S.580-6 [1] and ITU-R S.465-5 [2] for small antennas, i.e., with a diameter lower than 50 wavelengths, is introduced. It is a planar and a compact structure with a size of 40×40×2 cm. The antenna is formed by an array of 256 printed elements covering a large bandwidth (14.7%) at X-Band. The specification includes transmission (Tx) and reception (Rx) bands simultaneously. The printed antenna has a radiation pattern with a 3dB beamwidth of 5°, over a 31dBi gain, and a dual and an interchangeable circular polarization

Portable low profile antenna at X-band

An antenna which has been conceived as a portable system for satellite communications based on the recommendations ITU-R S.580-6 and ITU-R S.465-5 for small antennas, i.e., with a diameter lower than 50 wavelengths, is introduced. It is a planar and a compact structure with a size of 40×40×2 cm. The antenna is formed by an array of 256 printed elements covering a large bandwidth (14.7%) at X-Band with a VSWR of 1.4:1. The specification includes transmission (Tx) and reception (Rx) bands simultaneously. The printed antenna has a radiation pattern with a 3dB beamwidth of 5°, over a 31dBi gain, and a dual and an interchangeable circular polarization.

Dual circular polarized steering antenna for satellite communications in X band

In this work, a dual circular polarized steering antenna for satellite communications in X band is presented. The antenna consists of printed elements grouped in an array. This terminal works in a frequency band from 7.25 GHz up to 8.4 GHz (15% of bandwidth), where both bands, reception (RX) and transmission (TX) are included simultaneously and Left Handed Circular Polarization (LHCP) and Right Handed Circular Polarization (RHCP) are interchangeable. The antenna is compact, narrow bandwidth and reaches a gain of 16 dBi. It has the capability to steer in elevation to 45±, 75±, 105± and 135± electronically with a Butler matrix and 360± in azimuth with a motorized junction.

Low losses power distribution network at X band in stripline

An asymmetric stripline is proposed in this paper. The main aim of this line is to distribute the power among subarrays in an array with minimum losses. Several vertical transitions to subarrays are shown besides some network designs at X band for a square array for satellite communications.

Man-pack antenna at X-band

In this paper a low cost man-pack antenna for satellite communications at X band is presented. The antenna has dual circular polarization in Tx and Rx.

Matriz de Butler de Banda Ancha en Banda X para Antenas Reconfigurables

The work presented in this document shows the complete simulation of a Butler matrix. This circuit will be used in the feeding of a steerable on board antenna in X band. The antenna consists of printed elements grouped in an array. This terminal works in a frequency band from 7.25 up to 8.4 GHz (15% of bandwidth), where both bands, reception (7.25 – 7.75 GHz) and transmission (7.9–8.4 GHz), are included simultaneously. The whole antenna reaches 31 dBi, with a beam width smaller than 10º and a dual circular polarization. This antenna also includes the capability of electronic steering in elevation ±45º and mechanically motorized junction 360º in azimuth.

Conformación de Superficies Reflectoras de Sistemas Dobles de Tipo Offset con Alimentadores descritos en Campo Próximo

This work discusses an iterative procedure of shaping offset dual-reflector antennas based on geometrical optics considering both far-field and near-field measurements of amplitude and phase from the feed horn. The surfaces synthesized will transform a known radiation field of a feed to a desired aperture distribution. This technique is applied for both circular and elliptical apertures and has the advantage to simplify the problem compared with existing techniques based on solving nonlinear differential equations. A MATLAB tool has been developed to implement the shaping algorithms. This procedure is applied for the design of a 1.1 m high-gain antenna for the ESA’s Solar Orbiter spacecraft. This antenna operating at X-band will manage high data rate and high efficiency communications with Earth stations.

Contribution to the design of waveguide-fed compound-slot arrays by means of equivalent circuit modelling

Los arrays de ranuras son sistemas de antennas conocidos desde los años 40, principalmente destinados a formar parte de sistemas rádar de navíos de combate y grandes estaciones terrenas donde el tamaño y el peso no eran altamente restrictivos. Con el paso de los años y debido sobre todo a importantes avances en materiales y métodos de fabricación, el rango de aplicaciones de este tipo de sistemas radiantes creció en gran medida. Desde nuevas tecnologías biomédicas, sistemas anticolisión en automóviles y navegación en aviones, enlaces de comunicaciones de alta tasa binaria y corta distancia e incluso sistemas embarcados en satélites para la transmisión de señal de televisión. Dentro de esta familia de antennas, existen dos grupos que destacan por ser los más utilizados: las antennas de placas paralelas con las ranuras distribuidas de forma circular o espiral y las agrupaciones de arrays lineales construidos sobre guia de onda. Continuando con las tareas de investigación desarrolladas durante los últimos años en el Instituto de Tecnología de Tokyo y en el Grupo de Radiación de la Universidad Politécnica de Madrid, la totalidad de esta tesis se centra en este último grupo, aunque como se verá se separa en gran medida de las técnicas de diseño y metodologías convencionales. Los arrays de ranuras rectas y paralelas al eje de la guía rectangular que las alimenta son, sin ninguna duda, los modelos más empleados debido a la fiabilidad que presentan a altas frecuencias, su capacidad para gestionar grandes cantidades de potencia y la sencillez de su diseño y fabricación. Sin embargo, también presentan desventajas como estrecho ancho de banda en pérdidas de retorno y rápida degradación del diagrama de radiación con la frecuencia. Éstas son debidas a la naturaleza resonante de sus elementos radiantes: al perder la resonancia, el sistema global se desajusta y sus prestaciones degeneran. En arrays bidimensionales de slots rectos, el campo eléctrico queda polarizado sobre el plano transversal a las ranuras, correspondiéndose con el plano de altos lóbulos secundarios. Esta tesis tiene como objetivo el desarrollo de un método sistemático de diseño de arrays de ranuras inclinadas y desplazadas del centro (en lo sucesivo “ranuras compuestas”), definido en 1971 como uno de los desafíos a superar dentro del mundo del diseño de antennas. La técnica empleada se basa en el Método de los Momentos, la Teoría de Circuitos y la Teoría de Conexión Aleatoria de Matrices de Dispersión. Al tratarse de un método circuital, la primera parte de la tesis se corresponde con el estudio de la aplicabilidad de las redes equivalentes fundamentales, su capacidad para recrear fenómenos físicos de la ranura, las limitaciones y ventajas que presentan para caracterizar las diferentes configuraciones de slot compuesto. Se profundiza en las diferencias entre las redes en T y en ! y se condiciona la selección de una u otra dependiendo del tipo de elemento radiante. Una vez seleccionado el tipo de red a emplear en el diseño del sistema, se ha desarrollado un algoritmo de cascadeo progresivo desde el puerto alimentador hacia el cortocircuito que termina el modelo. Este algoritmo es independiente del número de elementos, la frecuencia central de funcionamiento, del ángulo de inclinación de las ranuras y de la red equivalente seleccionada (en T o en !). Se basa en definir el diseño del array como un Problema de Satisfacción de Condiciones (en inglés, Constraint Satisfaction Problem) que se resuelve por un método de Búsqueda en Retroceso (Backtracking algorithm). Como resultado devuelve un circuito equivalente del array completo adaptado a su entrada y cuyos elementos consumen una potencia acorde a una distribución de amplitud dada para el array. En toda agrupación de antennas, el acoplo mutuo entre elementos a través del campo radiado representa uno de los principales problemas para el ingeniero y sus efectos perjudican a las prestaciones globales del sistema, tanto en adaptación como en capacidad de radiación. El empleo de circuito equivalente se descartó por la dificultad que suponía la caracterización de estos efectos y su inclusión en la etapa de diseño. En esta tesis doctoral el acoplo también se ha modelado como una red equivalente cuyos elementos son transformadores ideales y admitancias, conectada al conjunto de redes equivalentes que representa el array. Al comparar los resultados estimados en términos de pérdidas de retorno y radiación con aquellos obtenidos a partir de programas comerciales populares como CST Microwave Studio se confirma la validez del método aquí propuesto, el primer método de diseño sistemático de arrays de ranuras compuestos alimentados por guía de onda rectangular. Al tratarse de ranuras no resonantes, el ancho de banda en pérdidas de retorno es mucho mas amplio que el que presentan arrays de slots rectos. Para arrays bidimensionales, el ángulo de inclinación puede ajustarse de manera que el campo quede polarizado en los planos de bajos lóbulos secundarios. Además de simulaciones se han diseñado, construido y medido dos prototipos centrados en la frecuencia de 12GHz, de seis y diez elementos. Las medidas de pérdidas de retorno y diagrama de radiación revelan excelentes resultados, certificando la bondad del método genuino Method of Moments - Forward Matching Procedure desarrollado a lo largo de esta tésis. Abstract The slot antenna arrays are well known systems from the decade of 40s, mainly intended to be part of radar systems of large warships and terrestrial stations where size and weight were not highly restrictive. Over the years, mainly due to significant advances in materials and manufacturing methods, the range of applications of this type of radiating systems grew significantly. From new biomedical technologies, collision avoidance systems in cars and aircraft navigation, short communication links with high bit transfer rate and even embedded systems in satellites for television broadcast. Within this family of antennas, two groups stand out as being the most frequent in the literature: parallel plate antennas with slots placed in a circular or spiral distribution and clusters of waveguide linear arrays. To continue the vast research work carried out during the last decades in the Tokyo Institute of Technology and in the Radiation Group at the Universidad Politécnica de Madrid, this thesis focuses on the latter group, although it represents a technique that drastically breaks with traditional design methodologies. The arrays of slots straight and parallel to the axis of the feeding rectangular waveguide are without a doubt the most used models because of the reliability that they present at high frequencies, its ability to handle large amounts of power and their simplicity of design and manufacturing. However, there also exist disadvantages as narrow bandwidth in return loss and rapid degradation of the radiation pattern with frequency. These are due to the resonant nature of radiating elements: away from the resonance status, the overall system performance and radiation pattern diminish. For two-dimensional arrays of straight slots, the electric field is polarized transverse to the radiators, corresponding to the plane of high side-lobe level. This thesis aims to develop a systematic method of designing arrays of angled and displaced slots (hereinafter "compound slots"), defined in 1971 as one of the challenges to overcome in the world of antenna design. The used technique is based on the Method of Moments, Circuit Theory and the Theory of Scattering Matrices Connection. Being a circuitry-based method, the first part of this dissertation corresponds to the study of the applicability of the basic equivalent networks, their ability to recreate the slot physical phenomena, their limitations and advantages presented to characterize different compound slot configurations. It delves into the differences of T and ! and determines the selection of the most suitable one depending on the type of radiating element. Once the type of network to be used in the system design is selected, a progressive algorithm called Forward Matching Procedure has been developed to connect the proper equivalent networks from the feeder port to shorted ending. This algorithm is independent of the number of elements, the central operating frequency, the angle of inclination of the slots and selected equivalent network (T or ! networks). It is based on the definition of the array design as a Constraint Satisfaction Problem, solved by means of a Backtracking Algorithm. As a result, the method returns an equivalent circuit of the whole array which is matched at its input port and whose elements consume a power according to a given amplitude distribution for the array. In any group of antennas, the mutual coupling between elements through the radiated field represents one of the biggest problems that the engineer faces and its effects are detrimental to the overall performance of the system, both in radiation capabilities and return loss. The employment of an equivalent circuit for the array design was discarded by some authors because of the difficulty involved in the characterization of the coupling effects and their inclusion in the design stage. In this thesis the coupling has also been modeled as an equivalent network whose elements are ideal transformers and admittances connected to the set of equivalent networks that represent the antennas of the array. By comparing the estimated results in terms of return loss and radiation with those obtained from popular commercial software as CST Microwave Studio, the validity of the proposed method is fully confirmed, representing the first method of systematic design of compound-slot arrays fed by rectangular waveguide. Since these slots do not work under the resonant status, the bandwidth in return loss is much wider than the longitudinal-slot arrays. For the case of two-dimensional arrays, the angle of inclination can be adjusted so that the field is polarized at the low side-lobe level plane. Besides the performed full-wave simulations two prototypes of six and ten elements for the X-band have been designed, built and measured, revealing excellent results and agreement with the expected results. These facts certify that the genuine technique Method of Moments - Matching Forward Procedure developed along this thesis is valid and trustable.

Mutual coupling reduction using EBG in steering antennas

In this letter, a dual circular polarized steering antenna for satellite communications in X-band is presented. This antenna consists of printed elements grouped in an array, able to work from 7.25 up to 8.4 GHz in both polarizations: left-handed circular polarization (LHCP) and right-handed circular polarization (RHCP). The module antenna is compact, with narrow beamwidth, and reaches a gain of 16 dBi. It has the capability to steer in elevation to and electronically with a Butler matrix. In order to reduce the mutual coupling between adjacent patches, electromagnetic band-gap (EBG) structures are introduced. These EBGs combine double-layer and edge location via in order to reduce the size, without changing the low-permittivity substrate, and therefore maintaining the high radiation efficiency of the antenna.

Contribución a los arrays de antenas activos en microondas = Contribution to active array antennas at microwave bands

Esta tesis que tiene por título "Contribución a los arrays de antenas activos en banda X", ha sido desarrollada por el estudiante de doctorado Gonzalo Expósito Domínguez, ingeniero de telecomunicación en el Grupo de Radiación del Departamento de Señales, Sistemas y Radiocomunicaciones de la ETSI de Telecomunicación de la Universidad Politécnica de Madrid bajo la dirección de los doctores Manuel Sierra Castañer y José Manuel Fernández González. Esta tesis contiene un profundo estudio del arte en materia de antenas activas en el campo de apuntamiento electrónico. Este estudio comprende desde los fundamentos de este tipo de antenas, problemas de operación y limitaciones hasta los sistemas actuales más avanzados. En ella se identifican las partes críticas en el diseño y posteriormente se llevan a la práctica con el diseño, simulación y construcción de un subarray de una antena integrada en el fuselaje de un avión para comunicaciones multimedia por satélite que funciona en banda X. El prototipo consta de una red de distribución multihaz de banda ancha y una antena planar. El objetivo de esta tesis es el de aplicar nuevas técnicas al diseño de antenas de apuntamiento electrónico. Es por eso que las contribuciones originales son la aplicación de barreras electromagnéticas entre elementos radiantes para reducir los acoplamientos mutuos en arrays de exploración electrónica y el diseño de redes desfasadoras sencillas en las que no son necesarios complejos desfasadores para antenas multihaz. Hasta la fecha, las barreras electromagnéticas, Electronic Band Gap (EBG), se construyen en sustratos de permitividad alta con el fin de aumentar el espacio disponible entre elementos radiantes y reducir el tamaño de estas estructuras. Sin embargo, la utilización de sustratos de alta permitividad aumenta la propagación por ondas de superficie y con ellas el acoplo mutuo. Utilizando sustratos multicapa y colocando la vía de las estructuras en su borde, en vez de en su centro, se consigue reducir el tamaño sin necesidad de usar sustratos de alta permitividad, reducir la eficiencia de radiación de la antena o aumentar la propagación por ondas de superficie. La última parte de la tesis se dedica a las redes conmutadoras y desfasadoras para antenas multihaz. El diseño de las redes de distribución para antenas son una parte crítica ya que se comportan como un atenuador a la entrada de la cadena receptora, modificando en gran medida la figura de ruido del sistema. Las pérdidas de un desfasador digital varían con el desfase introducido, por ese motivo es necesario caracterizar y calibrar los dispositivos correctamente. Los trabajos presentados en este manuscrito constan de un desfasador reflectivo con un conmutador doble serie paralelo para igualar las pérdidas de inserción en los dos estados y también un conmutador de una entrada y dos salidas cuyos puertos están adaptados en todo momento independientemente del camino del conmutador para evitar las reflexiones y fugas entre redes o elementos radiantes. El tomo finaliza con un resumen de las publicaciones en revistas científicas y ponencias en congresos, nacionales e internacionales, el marco de trabajo en el que se ha desarrollado, las colaboraciones que se han realizado y las líneas de investigación futuras. ABSTRACT This thesis was carried out in the Radiation Group of the Signals, Systems and Radiocomunications department of ETSI de Telecomunicación from Technical University of Madrid. Its title is "Contribution to active array antennas at X band" and it is developed by Gonzalo Expósito Domínguez, Electrical Engineer MsC. under the supervision of Prof. Dr. Manuel Sierra Castañer and Dr. José Manuel Fernández González. This thesis is focused on active antennas, specifically multibeam and electronic steering antenas. In the first part of the thesis a thorough description of the state of the art is presented. This study compiles the fundamentals of this antennas, operation problems and limits, up to the breakthrough applications. The critical design problems are described to use them eventually in the design, simulation and prototyping of an airborne steering array antenna for satellite communication at X band. The main objective of this thesis is to apply new techniques to the design of electronically steering antennas. Therefore the new original contributions are the application of Electromagnetic Band Gap materials (EBG) between radiating elements to reduce the mutual coupling when phase shift between elements exist and phase shifting networks where special characteristics are required. So far, the EBG structures have been constructed with high permitivity substrates in order to increase the available space between radiating elements and reduce the size of the structures. However, the surface wave propagation modes are enhanced and therefore the mutual coupling increases when high permitivity substrates are used. By using multilayered substrates and edge location via, the size is reduced meanwhile low permitivity substrates are used without reducing the radiation efficiency or enhancing the surface propagation modes. The last part of the thesis is focused on the phase shifting distribution networks for multibeam antennas. This is a critical part in the antenna design because the insertion loss in the distribution network behaves as an attenuator located in the first place in a receiver chain. The insertion loss will affect directly to the receiver noise figure and the insertion loss in a phase shifter vary with the phase shift. Therefore the devices must be well characterized and calibrated in order to obtain a properly operation. The work developed in this thesis are a reflective phase shifter with a series-shunt switch in order to make symmetrical the insertion loss for the two states and a complex Single Pole Double Through (SPDT) with matched ports in order to reduce the reflections and leakage between feeding networks and radiating elements. The end of this Ph D. dissertation concludes with a summary of the publications in national and international conferences and scientific journals, the collaborations carried out along the thesis and the future research lines.

Luminescence from two-dimensional electron gases in InAlN/GaN heterostructures with different In content

The luminescence properties of InxAl1−xN/GaN heterostructures are investigated systematically as a function of the In content (x = 0.067 − 0.208). The recombination between electrons confined in the two-dimensional electron gas and free holes in the GaN template is identified and analyzed. We find a systematic shift of the recombination with increasing In content from about 80 meV to only few meV below the GaN exciton emission. These results are compared with model calculations and can be attributed to the changing band profile and originating from the polarization gradient between InAlN and GaN.