Dry cooling with night cool storage to enhance solar power plants performance in extreme conditions areas

Solar thermal power plants are usually installed in locations with high yearly average solar radiation, often deserts. In such conditions, cooling water required for thermodynamic cycles is rarely available. Moreover, when solar radiation is high, ambient temperature is very high as well; this leads to excessive condensation temperature, especially when air-condensers are used, and decreases the plant efficiency. However, temperature variation in deserts is often very high, which drives to relatively low temperatures during the night. This fact can be exploited with the use of a closed cooling system, so that the coolant (water) is chilled during the night and store. Chilled water is then used during peak temperature hours to cool the condenser (dry cooling), thus enhancing power output and efficiency. The present work analyzes the performance improvement achieved by night thermal cool storage, compared to its equivalent air cooled power plant. Dry cooling is proved to be energy-effective for moderately high day–night temperature differences (20 °C), often found in desert locations. The storage volume requirement for different power plant efficiencies has also been studied, resulting on an asymptotic tendency.

Impact assessment of an integrated approach for thermal power generation plants asset management in the current energy market

El sector energético, en España en particular, y de forma similar en los principales países de Europa, cuenta con una significativa sobrecapacidad de generación, debido al rápido y significativo crecimiento de las energías renovables en los últimos diez años y la reducción de la demanda energética, como consecuencia de la crisis económica. Esta situación ha hecho que las centrales térmicas de generación de electricidad, y en concreto los ciclos combinados de gas, operen con un factor de utilización extremadamente bajo, del orden del 10%. Además de la reducción de ingresos, esto supone para las plantas trabajar continuamente fuera del punto de diseño, provocando una significativa pérdida de rendimiento y mayores costes de explotación. En este escenario, cualquier contribución que ayude a mejorar la eficiencia y la condición de los equipos, es positivamente considerada. La gestión de activos está ganando relevancia como un proceso multidisciplinar e integrado, tal y como refleja la reciente publicación de las normas ISO 55000:2014. Como proceso global e integrado, la gestión de activos requiere el manejo de diversos procesos y grandes volúmenes de información, incluso en tiempo real. Para ello es necesario utilizar tecnologías de la información y aplicaciones de software. Esta tesis desarrolla un concepto integrado de gestión de activos (Integrated Plant Management – IPM) aplicado a centrales de ciclo combinado y una metodología para estimar el beneficio aportado por el mismo. Debido a las incertidumbres asociadas a la estimación del beneficio, se ha optado por un análisis probabilístico coste-beneficio. Así mismo, el análisis cuantitativo se ha completado con una validación cualitativa del beneficio aportado por las tecnologías incorporadas al concepto de gestión integrada de activos, mediante una entrevista realizada a expertos del sector de generación de energía. Los resultados del análisis coste-beneficio son positivos, incluso en el desfavorable escenario con un factor de utilización de sólo el 10% y muy prometedores para factores de utilización por encima del 30%. ABSTRACT The energy sector particularly in Spain, and in a similar way in Europe, has a significant overcapacity due to the big growth of the renewable energies in the last ten years, and it is seriously affected by the demand decrease due to the economic crisis. That situation has forced the thermal plants and in particular, the combined cycles to operate with extremely low annual average capacity factors, very close to 10%. Apart from the incomes reduction, working in out-of-design conditions, means getting a worse performance and higher costs than expected. In this scenario, anything that can be done to improve the efficiency and the equipment condition is positively received. Asset Management, as a multidisciplinary and integrated process, is gaining prominence, reflected in the recent publication of the ISO 55000 series in 2014. Dealing Asset Management as a global, integrated process needs to manage several processes and significant volumes of information, also in real time, that requires information technologies and software applications to support it. This thesis proposes an integrated asset management concept (Integrated Plant Management-IPM) applied to combined cycle power plants and develops a methodology to assess the benefit that it can provide. Due to the difficulties in getting deterministic benefit estimation, a statistical approach has been adopted for the cot-benefit analysis. As well, the quantitative analysis has been completed with a qualitative validation of the technologies included in the IPM and their contribution to key power plant challenges by power generation sector experts. The cost- benefit analysis provides positive results even in the negative scenario of annual average capacity factor close to 10% and is promising for capacity factors over 30%.

Absorption and mobility of foliar-applied boron in soybean as affected by plant boron status and application as a polyol complex

In the present study (i) the impact of plant Boron (B) status on foliar B absorption and (ii) the effect of B complexation with polyols (sorbitol or mannitol) on B absorption and translocation was investigated. Soybean (Glycine max (L.) Meer.) plants grown in nutrient solution containing 0 μM, 10 μM, 30 μM or 100 μM 11B labelled boric acid (BA) were treated with 50 mM 10B labelled BA applied to the basal parts of two leaflets of one leaf, either pure or in combination with 500 mM sorbitol or mannitol. After one week, 10B concentrations in different plant parts were determined. In B deficient leaves (0 μM 11B), 10B absorption was significantly lower than in all other treatments (9.7% of the applied dose vs. 26%–32%). The application of BA in combination with polyols increased absorption by 18–25% as compared to pure BA. The absolute amount of applied 10B moving out of the application zone was lowest in plants with 0 μM 11B supply (1.1% of the applied dose) and highest in those grown in 100 μM 11B (2.8%). The presence of sorbitol significantly decreased the share of mobile 10B in relation to the amount absorbed. The results suggest that 11B deficiency reduces the permeability of the leaf surface for BA. The addition of polyols may increase 10B absorption, but did not improve 10B distribution within the plant, which was even hindered when applied a sorbitol complex.

Environmental assay on the effect of poultry manure application on soil organisms in agroecosystems

This paper reports the effects produced on the organisms of the soil (plants, invertebrates and microorganisms), after the application of two types of poultry manure (sawdust and straw bed) on an agricultural land. The test was made using a terrestrial microcosm, Multi-Species Soil System (MS3) developed in INIA. There was no difference in the germination for any of the three species of plants considered in the study. The biomass was increased in the wheat (Triticum aestivum) coming from ground treated with both kinds of poultry manure. Oilseed rape (Brasica rapa) was not affected and regarding vetch (Vicia sativa) only straw poultry manure showed significant difference. For length only Vicia sativa was affected showing a reduction when straw was exposed to poultry manure. When the effect on invertebrates was studied, we observed a reduction in the number of worms during the test, especially from the ground control (13.7%), higher than in the ground with sawdust poultry manure (6.7%), whereas in the ground with straw poultry manure, there was no reduction. The biomass was affected and at the end of the test it was observed that while the reduction of worms in the ground control was about 48%, the number of those that were in the ground with sawdust poultry manure or straw poultry manure decreased by 41% and 22% respectively. Finally, the effects on microorganisms showed that the enzymatic activities: dehydrogenase (DH) and phosphatase and basal respiration rate increased at the beginning of the test, and the differences were statistically significant compared with the values of the control group. During the test, all these parameters decreased (except DH activities) but they were always higher than in the ground control. This is why it is possible to deduce that the contribution of poultry manure caused an improvement in the conditions of fertilization and also for the soil.

Automatic segmentation of relevant textures in agricultural images

One important issue emerging strongly in agriculture is related with the automatization of tasks, where the optical sensors play an important role. They provide images that must be conveniently processed. The most relevantimage processing procedures require the identification of green plants, in our experiments they come from barley and corn crops including weeds, so that some types of action can be carried out, including site-specific treatments with chemical products or mechanical manipulations. Also the identification of textures belonging to the soil could be useful to know some variables, such as humidity, smoothness or any others. Finally, from the point of view of the autonomous robot navigation, where the robot is equipped with the imaging system, some times it is convenient to know not only the soil information and the plants growing in the soil but also additional information supplied by global references based on specific areas. This implies that the images to be processed contain textures of three main types to be identified: green plants, soil and sky if any. This paper proposes a new automatic approach for segmenting these main textures and also to refine the identification of sub-textures inside the main ones. Concerning the green identification, we propose a new approach that exploits the performance of existing strategies by combining them. The combination takes into account the relevance of the information provided by each strategy based on the intensity variability. This makes an important contribution. The combination of thresholding approaches, for segmenting the soil and the sky, makes the second contribution; finally the adjusting of the supervised fuzzy clustering approach for identifying sub-textures automatically, makes the third finding. The performance of the method allows to verify its viability for automatic tasks in agriculture based on image processing

Phytostabilization of metals in mine soils using Brassica juncea in combination with organic amendments

Background and aims The high metal bioavailability and the poor conditions of mine soils yield a low plant biomass, limiting the application of phytoremediation techniques. A greenhouse experiment was performed to evaluate the effects of organic amendments on metal stabilization and the potential of Brassica juncea L. for phytostabilization in mine soils. Methods Plants were grown in pots filled with soils collected from two mine sites located in Central Spain mixed with 0, 30 and 60 tha?1 of pine bark compost and horse- and sheep-manure compost. Plant biomass and metal concentrations in roots and shoots were measured. Metal bioavailability was assessed using a rhizosphere-based method (rhizo), which consists of a mixture of low-molecular-weight organic acids to simulate root exudates. Results Manure reduced metal concentrations in shoots (10?50 % reduction of Cu and 40?80 % of Zn in comparison with non-amended soils), bioconcentration factor (10?50 % of Cu and 40?80 % of Zn) and metal bioavailability in soil (40?50 % of Cu and 10?30 % of Zn) due to the high pH and the contribution of organic matter. Manure improved soil fertility and was also able to increase plant biomass (5?20 times in shoots and 3?30 times in roots), which resulted in a greater amount of metals removed from soil and accumulated in roots (increase of 2?7 times of Cu and Zn). Plants grown in pine bark treatments and in non-amended soils showed a limited biomass and high metal concentrations in shoots. Conclusions The addition of manure could be effective for the stabilization of metals and for enhancing the phytostabilization ability of B. juncea in mine soils. In this study, this species resulted to be a potential candidate for phytostabilization in combination with manure, differing from previous results, in which B. juncea had been recognized as a phytoextraction plant.

Uncovering cold disruption of the circadian clock in poplar

Dormancy is an adaptive mechanism that allows woody plants to survive at low temperatures during the winter. Disruption of circadian clock genes in winter or under low temperatures, both in long days as in short days, were described in our group few years ago (Ramos et al., 2005). Basic mechanisms of the circadian clock function are similar in herbaceous as well as in woody plants although there are differences in their response to low temperatures (Bieniawska et al., 2008). Woody plants growing in daylight conditions should have a specific transcriptional control above the circadian clock genes, which is responsible of their constitutive transcriptional activation observed under low temperatures conditions. In order to understand this regulatory process, we are analyzing the behavior of a circadian clock gene in poplar. To this aim, we have isolated its promoter region and fused to the luciferase reporter gene. This construct has been transformed into Populus tremula x P. alba 717-1B4 INRA clone. Here we present the characterization of these transgenic lines under different conditions of light and temperature.

Habitat management for conservation of pollinators in agro-ecosystems of Central Spain

La gestión de hábitat orientada a la conservación de polinizadores en los agro-ecosistemas requiere una selección de especies vegetales atendiendo fundamentalmente a dos criterios: i) el potencial atractivo de sus flores a los polinizadores; y ii) la simplicidad en su manejo agronómico. Además de estas premisas, es necesario considerar la capacidad invasora de estas especies vegetales, debido a que algunas de las más atractivas pueden resultar invasoras en determinados agro-ecosistemas. Por lo tanto, es preciso determinar qué especies vegetales son las más indicadas para ser implementadas en cada agro-ecosistema. En la presente tesis doctoral se plantea la búsqueda de las especies vegetales adecuadas para atraer polinizadores en los agro-ecosistemas del centro de España. En una primera aproximación, se ha evaluado la atracción y expansión espacial (potencial invasivo) de seis plantas perennes de la familia Lamiaceae (aromáticas), elegidas por ser nativas de la región mediterránea. La elección de las especies vegetales se ha llevado a cabo con el fin de crear márgenes funcionales basados en la mezcla de especies vegetales con distintos periodos de floración, de modo que prolonguen la disponibilidad de recursos florales en el tiempo. Tras un primer año dedicado al establecimiento de las especies aromáticas, en los dos años siguientes se ha estudiado la atracción individual y combinada de las especies vegetales sobre los polinizadores, y como ésta se ve afectada por la densidad y la morfología floral, utilizando para ello un diseño experimental en bloques al azar. Los resultados de este estudio han puesto de manifiesto que la morfología floral no tuvo influencia sobre la atracción de las especies vegetales, pero si la densidad floral, puesto que las especies vegetales con mayor densidad de flores (Nepeta tuberosa e Hyssopus officinalis) han mostrado mayor atracción a polinizadores. Cabe destacar que de las seis especies consideradas, dos especies de verano (Melissa officinalis y Thymbra capitata) no han contribuido de forma efectiva a la atracción de la mezcla hacia los polinizadores, mostrando una reducción significativa de este parámetro respecto a las otras especies aromáticas a lo largo del verano. Se ha observado que ninguna de las especies aromáticas evaluadas ha mostrado tendencia invasora a lo largo del estudio. En base a estos resultados, se puede concluir que entre las especies aromáticas estudiadas, N. tuberosa, H. officinalis y Salvia verbenaca son las que ofrecen mayor potencial para ser utilizadas en la conservación de polinizadores. De forma similar al caso de las plantas aromáticas, se ha llevado a cabo una segunda experimentación que incluía doce plantas anuales con floración de primavera, en la que se evaluó la atracción a polinizadores y su comportamiento agronómico. Este estudio con especies herbáceas se ha prolongado durante dos años, utilizando un diseño experimental de bloques aleatorios. Las variables analizadas fueron: el atractivo de las distintas especies vegetales a los polinizadores, su eficiencia de atracción (calculada como una combinación de la duración de la floración y las visitas de insectos), su respuesta a dos tipos de manejo agronómico (cultivo en mezcla frente a monocultivo; laboreo frente a no-laboreo) y su potencial invasivo. Los resultados de esta segunda experimentación han mostrado que las flores de Borago officinalis, Echium plantagineum, Phacelia tanacetifolia y Diplotaxis tenuifolia son atractivas a las abejas, mientras que las flores de Calendula arvensis, Coriandrum sativum, D. tenuifolia y Lobularia maritima son atractivas a los sírfidos. Con independencia del tipo de polinizadores atraídos por cada especie vegetal, se ha observado una mayor eficiencia de atracción en parcelas con monocultivo de D. tenuifolia respecto a las parcelas donde se cultivó una mezcla de especies herbáceas, si bien en estas últimas se observó mayor eficiencia de atracción que en la mayoría de parcelas mono-específicas. Respecto al potencial invasivo de las especies herbáceas, a pesar de que algunas de las más atractivas a polinizadores (P. tanacetifolia and C. arvensis) mostraron tendencia a un comportamiento invasor, su capacidad de auto-reproducción se vio reducida con el laboreo. En resumen, D. tenuifolia es la única especie que presentó una alta eficiencia de atracción a distintos tipos de polinizadores, conjuntamente con una alta capacidad de auto-reproducción pero sin mostrar carácter invasor. Comparando el atractivo de las especies vegetales utilizadas en este estudio sobre los polinizadores, D. tenuifolia es la especie más recomendable para su cultivo orientado a la atracción de polinizadores en agro-ecosistemas en el centro de España. Esta especie herbácea, conocida como rúcula, tiene la ventaja añadida de ser una especie comercializada para el consumo humano. Además de su atractivo a polinizadores, deben considerarse otros aspectos relacionados con la fisiología y el comportamiento de esta especie vegetal en los agro-ecosistemas antes de recomendar su cultivo. Dado que el cultivo en un campo agrícola de una nueva especie vegetal implica unos costes de producción, por ejemplo debidos a la utilización de agua de riego, es necesario evaluar el incremento en dichos costes en función de demanda hídrica específica de esa especie vegetal. Esta variable es especialmente importante en zonas dónde se presentan sequías recurrentes como es el caso del centro y sur-este de la península Ibérica. Este razonamiento ha motivado un estudio sobre los efectos del estrés hídrico por sequía y el estrés por déficit moderado y severo de riego sobre el crecimiento y floración de la especie D. tenuifolia, así como sobre la atracción a polinizadores. Los resultados muestran que tanto el crecimiento y floración de D. tenuifolia como su atracción a polinizadores no se ven afectados si la falta de riego se produce durante un máximo de 4 días. Sin embargo, si la falta de riego se extiende a lo largo de 8 días o más, se observa una reducción significativa en el crecimiento vegetativo, el número de flores abiertas, el área total y el diámetro de dichas flores, así como en el diámetro y longitud del tubo de la corola. Por otro lado, el estudio pone de manifiesto que un déficit hídrico regulado permite una gestión eficiente del agua, la cual, dependiendo del objetivo final del cultivo de D. tenuifolia (para consumo o solo para atracción de polinizadores), puede reducir su consumo entre un 40 y un 70% sin afectar al crecimiento vegetativo y desarrollo floral, y sin reducir significativamente el atractivo a los polinizadores. Finalmente, esta tesis aborda un estudio para determinar cómo afecta el manejo de hábitat a la producción de los cultivos. En concreto, se ha planteado una experimentación que incluye márgenes mono-específicos y márgenes con una mezcla de especies atractivas a polinizadores, con el fin de determinar su efecto sobre la producción del cultivo de cilantro (C. sativum). La elección del cultivo de cilantro se debe a que requiere la polinización de insectos para su reproducción (aunque, en menor medida, puede polinizarse también por el viento), además de la facilidad para estimar su producción en condiciones semi-controladas de campo. El diseño experimental consistía en la siembra de márgenes mono-específicos de D. tenuifolia y márgenes con mezcla de seis especies anuales situados junto al cultivo de cilantro. Estos cultivos con márgenes florales fueron comparados con controles sin margen floral. Además, un segundo grupo de plantas de cilantro situadas junto a todos los tratamientos, cuyas flores fueron cubiertas para evitar su polinización, sirvió como control para evaluar la influencia de los polinizadores en la producción del cultivo. Los resultados muestran que la presencia de cualquiera de los dos tipos de margen floral mejora el peso y el porcentaje de germinación de las semillas de cilantro frente al control sin margen. Si se comparan los dos tipos de margen, se ha observado un mayor número de semillas de cilantro junto al margen con mezcla de especies florales respecto al margen mono-específico, probablemente debido al mayor número visitas de polinizadores. Puesto que el experimento se realizó en condiciones de campo semi-controladas, esto sugiere que las visitas de polinizadores fueron el factor determinante en los resultados. Por otro lado, los resultados apuntan a que la presencia de un margen floral (ya sea mono-especifico o de mezcla) en cultivos de pequeña escala puede aumentar la producción de cilantro en más de un 200%, al tiempo que contribuyen a la conservación de los polinizadores. ABSTRACT Habitat management, aimed to conserve pollinators in agro-ecosystems, requires selection of the most suitable plant species in terms of their attractiveness to pollinators and simplicity of agronomic management. However, since all flowers are not equally attractive to pollinators and many plant species can be weedy or invasive in the particular habitat, it is important to test which plant species are the most appropriate to be implemented in specific agro-ecosystems. For that reason, this PhD dissertation has been focused on determination of the most appropriate aromatic and herbaceous plants for conservation of pollinators in agro-ecosystems of Central Spain. Therefore, in a first approximation, spatial expansion (i.e. potential weediness) and attractiveness to pollinators of six aromatic perennial plants from the Lamiaceae family, native and frequent in the Mediterranean region, were evaluated. Preliminary plant selection was based on designing a functional mixed margins consisting of plants attractive to pollinators and with different blooming periods, in order to extend the availability of floral resources in the field. After a year of vegetative growth, the next two years the plant species were studied in a randomized block design experiment in order to estimate their attractiveness to pollinators in Central Spain and to investigate whether floral morphology and density affect attractiveness to pollinators. The final aim of the study was to evaluate how their phenology and attractiveness to pollinators can affect the functionality of a flowering mixture of these plants. In addition, the spatial expansion, i.e. potential weediness, of the selected plant species was estimated under field conditions, as the final purpose of the studied plants is to be implemented within agro-ecosystems. The results of the experiment showed that floral morphology did not affect the attractiveness of plants to pollinators, but floral density did, as plant species with higher floral density (i.e. Nepeta tuberosa and Hyssopus officinalis) showed significantly higher attractiveness to pollinators. In addition, of six plant species, two summer species (Melissa officinalis and Thymbra capitata) did not efficiently contribute to the attractiveness of the mixture to pollinators, which reduced its attractiveness during the summer period. Finally, as none of the plants showed weedy behaviour under field conditions, the attractive plant species, i.e. N. tuberosa, H. officinalis and the early spring flowering Salvia verbenaca, showed good potential to conserve the pollinators. Similarly, in a second approximation, the attractiveness to pollinators and agronomic behaviour of twelve herbaceous plants blooming in spring were studied. This experiment was conducted over two years in a randomized block design in order to evaluate attractiveness of preselected plant species to pollinators, as well as their attractiveness efficiency (a combination of duration of flowering and insect visitation), their response to two different agronomic management practices (growing in mixed vs. mono-specific plots; tillage vs. no-tillage), and their potential weediness. The results of this experiment showed that the flowers of Borago officinalis, Echium plantagineum, Phacelia tanacetifolia and Diplotaxis tenuifolia were attractive to bees, while Calendula arvensis, Coriandrum sativum, D. tenuifolia and Lobularia maritima were attractive to hoverflies. In addition, floral mixture resulted in lower attractiveness efficiency to pollinators than mono-specific D. tenuifolia, but higher than most of the mono-specific stands. On the other hand, although some of the most attractive plant species (e.g. P. tanacetifolia and C. arvensis) showed potential weediness, their self-seeding was reduced by tillage. After comparing attractiveness efficiency of various herbaceous species to pollinators and their potential weediness, the results indicated that D. tenuifolia showed the highest attractiveness efficiency to pollinators and efficient self-reproduction, making it highly recommended to attract bees and hoverflies in agro-ecosystems of Central Spain. In addition, this plant, commonly known as wild rocket, has a supplementary economic value as a commercialized crop. The implementation of a new floral margin in agro-ecosystems means increased production costs, especially in regions with frequent and long droughts (as it is Central and South-East area of Iberian Peninsula), where the principal agricultural cost is irrigation. Therefore, before recommending D. tenuifolia for sustainable habitat management within agro-ecosystems, it is necessary to study the effect of drought stress and moderate and severe deficit irrigation on its growth, flower development and attractiveness to pollinators. The results of this experiment showed that in greenhouse conditions, potted D. tenuifolia could be without irrigation for 4 days without affecting its growth, flowering and attractiveness to pollinators. However, lack of irrigation for 8 days or longer significantly reduced the vegetative growth, number of open flowers, total floral area, flower diameter, corolla tube diameter and corolla tube length of D. tenuifolia. This study showed that regulated deficit irrigation can improve water use efficiency, and depending on the purpose of growing D. tenuifolia, as a crop or as a beneficial plant to attract pollinators, it can reduce water consumption by 40% to 70% without affecting its vegetative and floral development and without reducing its attractiveness to pollinators. Finally, the following experiment was developed in order to understand how habitat management can influence on the agricultural production. For this purpose, it was evaluated if the vicinity of mixed and mono-specific field margins, preselected to conserve pollinators within agro-ecosystems, can improve seed production in coriander (C. sativum). The selection of this plant species for the experiment was based on its necessity for insect pollination for production of seeds (even though some pollen can be transmitted from one flower to another by wind) and the fact that under semi-controlled field conditions established in the field it is possible to estimate its total seed production. Since D. tenuifolia is attractive for both bees and hoverflies in Central Spain, the main objective of this experiment was to estimate the impact of two different types of field margins, i.e. mono-specific margin with D. tenuifolia and mixed margin with six herbaceous species, on the seed production of potted coriander. For that reason, it was tested: i) if open pollination (control without proximate field margin and treatments with nearby mono-specific and mixed margin) increases the seed production of coriander when compared with no-pollination (covered inflorescences of coriander) under field conditions; ii) if frequency of pollinator visitation to the flowers of coriander was higher in the presence of field margins than in the control without field margin; and iii) if seed production was higher in the presence of field margins than in control plants of coriander without field margin. The results showed that the proximity of both types of floral margins (mixed and mono-specific) improved the seed quality of coriander plants, as seed weight and germination rate were higher than in control plants without field margin. Furthermore, the number of seeds produced was significantly higher in coriander plants grown near mixed margins than near mono-specific margin, probably due to an increase in pollinator visits. Since the experiment was conducted under semi-controlled field conditions, it can be concluded that pollinator visits was the main factor that biased the results, and that presence of both mixed or mono-specific (D. tenuifolia) margins can improve the production of coriander for more than 200% in small-scale gardens and, in addition, conserve the local pollinators.

`Candidatus Liberibacter asiaticus´ titers in citrus and acquisition rates by Diaphorina citri are decreased by higher temperature

`Candidatus Liberibacter asiaticus´ is the most prevalent Liberibacter sp. associated with huanglongbing (HLB) in Brazil. Within São Paulo state (SP), HLB has spread more rapidly to and reached higher incidence in regions with relatively mild (cooler) summer temperatures. This suggests that climate can influence disease spread and severity. ?Ca. L. asiaticus? titers on soft, immature leaves from infected ?Valencia? sweet orange plants exposed to different temperature regimes and adult Diaphorina citri fed for 48 h on these plants for ?Ca. L. asiaticus? acquisition were determined by quantitative polymerase chain reaction in two experiments. The first experiment included plants with three levels of infection, three incubation periods (IPs), and air temperatures favorable (14.6 to 28°C) and unfavorable (24 to 38°C) to ?Ca. L. asiaticus?. The second included plants with severe late-stage infections, 10 IPs (based on 3-day intervals over 27 days), and three air temperature regimes (12 to 24, 18 to 30, and 24 to 38°C). Overall, ?Ca. L. asiaticus? titers and the percentages of ?Ca. L. asiaticus?-positive psyllids were lower in plants maintained at the warmer temperature regime (24 to 38°C) than in plants maintained in the cooler regimes. The results suggest that the lower incidence and slower spread of ?Ca. L. asiaticus? to warmer regions of SP are related to the influence of ambient temperatures on titers of ?Ca. L. asiaticus? in leaves.

Assessing Creativity In Engineering Students: A Comparative Between Degrees and Sudents In First And Last Year

An online open access test (CREAX self-assessment) has been used in this work so that students from degrees in engineering in the Universidad Polite¿cnica of Madrid (UPM) could self-assess their creative competence after several classroom activities. Different groups from the first year course have been statistically compared using data from their assessment. These first year students had different professors in the subject ?Technical Drawing? and belonged to several degrees in the UPM. They were as well compared regarding sex and a group of first year students was also compared to another last year group of the degree so as to observe possible differences in the achievement of this competence. Only one difference was detected concerning sex in one of the degrees. Among degrees, the higher marks obtained by students who had done specific exercises for the development of creativity in class is highlighted. Finally, a significantly high mark was observed in students during their last year of degree with respect to first year students. The tool CREAX has become very useful in the assessment of this competence in the UPM degrees in which it has been implemented.

Plant β-diversity i in human-altered forest ecosystems: the importance of the structural, spatial, and topographical characteristics of stands in patterning plant species assemblages

An understanding of spatial patterns of plant species diversity and the factors that drive those patterns is critical for the development of appropriate biodiversity management in forest ecosystems. We studied the spatial organization of plants species in human- modified and managed oak forests (primarily, Quercus faginea) in the Central Pre- Pyrenees, Spain. To test whether plant community assemblages varied non-randomly across the spatial scales, we used multiplicative diversity partitioning based on a nested hierarchical design of three increasingly coarser spatial scales (transect, stand, region). To quantify the importance of the structural, spatial, and topographical characteristics of stands in patterning plant species assemblages and identify the determinants of plant diversity patterns, we used canonical ordination. We observed a high contribution of ˟-diversity to total -diversity and found ˟-diversity to be higher and ˞-diversity to be lower than expected by random distributions of individuals at different spatial scales. Results, however, partly depended on the weighting of rare and abundant species. Variables expressing the historical management intensities of the stand such as mean stand age, the abundance of the dominant tree species (Q. faginea), age structure of the stand, and stand size were the main factors that explained the compositional variation in plant communities. The results indicate that (1) the structural, spatial, and topographical characteristics of the forest stands have the greatest effect on diversity patterns, (2) forests in landscapes that have different land use histories are environmentally heterogeneous and, therefore, can experience high levels of compositional differentiation, even at local scales (e.g., within the same stand). Maintaining habitat heterogeneity at multiple spatial scales should be considered in the development of management plans for enhancing plant diversity and related functions in human-altered forests

Native bradyrhizobial symbionts of Lupinus mariae-josephae, a unique endemism thriving in alkaline soils in Eastern Spain

Lupinus mariae-josephae (Lmj) es una especie de lupino endémica de una pequeña y específica área de Comunidad Valenciana (Este de España), donde prospera en suelos alcalinoscalcáreos, un hábitat singular para los altramuces, que crecen preferentemente en suelos ácidos o neutros. Esto hace de Lmj una especie de lupino única. Cuando se inició este trabajo, la extensión conocida de este endemismo abarcaba unos 700 kilómetros cuadrados, confinados en la provincia de Valencia. En esta área, Lmj prospera en pequeñas poblaciones aisladas que contienen un número reducido de plantas por lo que se la consideró una especie en peligro de extinción. Todos los esfuerzos, utilizando estrategias clásicas dirigidas a ampliar el área de crecimiento de Lmj y garantizar su conservación, han tenido un éxito limitado. El trabajo que se presenta está dirigido a mejorar el conocimiento de la ecología de Lmj, en particular la interacción simbiótica que establece con bacterias del suelo denominadas rizobios y se centra en la caracterización fenotípica, filogenética y genómica de esos rizobios. También se investiga la posible contribución de la simbiosis en mejorar la conservación de Lmj. Para este fin, se han estudiado diferentes aspectos que se describen a continuación. El primero objetivo se centró en aislar y estudiar de la diversidad genética de las bacterias endosimbióticas de Lmj. . Se realizó un análisis filogenético de genes esenciales que mostró que las cepas de Lmj pertenecen al género Bradyrhizobium y que presentan una gran diversidad con características fenotípicas y simbióticas diferentes de cepas de Bradyrhizobium que nodulan otras especies de lupinos nativos de España (cepas ISLU). Las cepas estudiadas se dividieron en dos grupos (Clado I y Clado II). El Clado I, incluye a las cepas Lmj, definiendo un nuevo linaje, filogenéticamente relacionado con otras especies de Bradyrhizobium, como B. jicamae y B. elkanii. El Clado II contiene cepas ISLU relacionadas con cepas de B. canariense y B. japonicum que establecen simbiosis con lupinos de suelos ácidos. Otro análisis filogenético basado en genes simbióticos, distribuyó las cepas de Lmj en sólo dos grupos diferentes. La singularidad y gran diversidad de estas cepas en una pequeña área geográfica, hacen de este, un atractivo sistema para el estudio de la evolución y adaptación de las bacterias simbióticas a su respectiva planta huésped. Adicionalmente, se estudio la presencia de bacterias capaces de nodular Lmj en suelos básicos de Chiapas, México. Sorprendentemente, estos suelos contienen bacterias capaces establecer interacciones simbióticas eficientes con Lmj en ensayos de invernadero. A continuación se investigó la taxonomía de los endosimbiontes de Lmj analizando la secuencia de cuatro genes esenciales (16S rRNA, recA, glnII y atpD) y el promedio de identidad de nucleótidos de genomas completos de algunas cepas representativas de la diversidad (ANIm). Se identificaron nuevas especies de Bradyrhizobium dentro del Clado I y se definió una de ellas: 'Bradyrhizobium valentinum' sp. nov (cepa tipo LmjM3T = CECT 8364T, LMG 2761T). También se abordó cómo conservar Lmj en su hábitat natural mediante inoculación con alguna de las cepas aisladas. Se demostró la ausencia de bacterias capaces de nodular Lmj en suelos rojos alcalinos o ‘‘terra rossa’’ de la Península Ibérica y Baleares. Dos cepas, altamente eficientes en cuanto a la fijación de nitrógeno, LmjC y LmjM3T, fueron seleccionadas para ser empleadas como inoculantes. Dos experimentos de campo llevados a cabo en años consecutivos en áreas con características edafoclimáticas similares a las que presentan las poblaciones de Lmj, lograron la reproducción exitosa de la planta. Se concluyó que un ciclo reproductivo exitoso de Lmj es absolutamente dependiente de la inoculación con sus simbiontes naturales y que la simbiosis debe ser considerada un factor esencial en estrategias de conservación de leguminosas en peligro. La obtención de varias secuencias genómicas de cepas aisladas de Lmj y de otras cepas de Bradyrhizobium reveló una alta similitud entre los genomas de las cepas del Clado I, y permitió la identificación de cinco posibles nuevas especies. Además, se estudiaron tres agrupaciones de genes relacionados con la simbiosis (nod, nif y fix) definiendo un nuevo linaje para las cepas de Lmj, diferente del symbiovar “genistearum” de B. canariense y B. japonicum. La baja diversidad encontrada en el análisis filogenético de los genes simbióticos contrasta con la gran diversidad asociada a genes esenciales. La presencia de plásmidos en cepas del género Bradyrhizobium ha sido descrita en muy pocas ocasiones, sin embargo el análisis de la secuencia genómica de la cepa ISLU101, aislada de Lupinus angustifolius, reveló la presencia de un origen de replicación extracromosómico homólogo al operón repABC, presente en el plásmido de Bradyrhizobium sp BTAi1. Gracias a esta secuencia se identificaron genes homólogos en 19 de 72 cepas ISLU. Filogenéticamente, las secuencias de repABC se agruparon en un grupo monofilético con las de pBTAi1 y separadas de los rizobios de crecimiento rápido. Finalmente, se identificaron sistemas de secreción de proteínas de tipo III (T3SS) en nueve genomas de cepas de Lmj. Los T3SS pueden inyectar proteínas efectoras al interior de células vegetales. Su presencia en rizobios se ha relacionado con la gama de hospedador que pueden nodular y puede tener un efecto beneficioso, neutro o perjudicial en la simbiosis. Los T3SS de las cepas de Lmj codifican para una proteína efectora similar a NopE, un efector dependiente de T3SS descrito en B. diazoefficiens USDA 110T. La proteína NopE de la cepa LmjC se ha caracterizado bioquímicamente. ABSTRACT Lupinus mariae-josephae (Lmj) is a lupine species endemic of a unique small area in Valencia region (Eastern Spain) where the lupine plants thrive in alkaline-limed soils, which preferentially grow in acid or neutral soils. This is the type of soils native lupines of Spain. When this work was initiated, the extension of the endemic area of Lmj was of about 700 squared kilometers confined to the Valencia province. In this area, Lmj thrives in small, isolated patches containing a reduced number of plants, and points to an endemism that can easily became endangered or extinct. Consequently, the Valencia Community authorities gave a ‘‘microreserve” status for conservation of the species. All efforts, using classical strategies directed to extend the area of Lmj growth and ensure its conservation have been so far unsuccessful. The work presented here is directed to improve our knowledge of Lmj ecology and it is centered in the characterization of the rhizobial symbiosis by phenotypic, phylogenetic and genomic analysis as well as in investigate the potential contribution of the symbiosis to improve its conservation. To this end, five different topics have been studied, and results are briefly described here. Extensive details can be followed en the attached, published articles. The first topic deals with the indigenous rhizobial symbionts of the Lmj endemism, and its genetic diversity was investigated. The Lmj root symbionts belong to the Bradyrhizobium genus, and phylogenetic analysis based on core genes identified a large diversity of Bradyrhizobium strains with phenotypic and symbiotic characteristics different from rhizobia nodulating other Lupinus spp. native of Spain. The strains were split in two clades. Clade II contained strains close to classical B. canariense and B. japonicum lineages that establish symbioses with lupines in acid soils of the Mediterranean area. Clade I included Lmj strains that define a new lineage, close to other Bradyrhizobium species as B. jicamae and B. elkanii. The phylogenetic analysis based on symbiotic genes identified only two distinct clusters. The singularity and large diversity of these strains in such a small geographical area makes this an attractive system for studying the evolution and adaptation of the rhizobial symbiont to the plant host. Additionally, the presence of bacteria able to nodulate Lmj in basic soils from Chiapas, Mexico was investigated. Surprisingly, these soils contain bacteria able to effectively nodulate and fix nitrogen with Lmj plants in greenhouse assays. In the second topic, the taxonomic status of the endosymbiotic bacteria of Lmj from Valencia endemism and Chiapas was investigated. Results from phylogenetic analysis of core genes and Average Nucleotide Identity (ANIm) using draft genomic sequences identified new Bradyrhizobium species within strains of Clade I of Lmj endosymbiotic bacteria. Only one of these potentially new species has been defined, meanwhile the others are under process of characterization. The name ‘Bradyrhizobium valentinum’ sp. nov. was proposed for the defined species (type strain LmjM3T= CECT 8364T, LMG 2761T). The third topic was directed to conservation of endangered Lmj in its natural habitat. The relevant conclusion of this experimentation is that the symbiosis should be considered as a relevant factor in the conservation strategies for endangered legumes. First, we showed absence of bacteria able to nodulate Lmj in all the inspected ‘‘terra rossa’’ or alkaline red soils of the Iberian Peninsula and Balearic Islands. Then, two efficient nitrogen fixing strains with Lmj plants, LmjC and LmjM3T, were selected as inoculum for seed coating. Two planting experiments were carried out in consecutive years under natural conditions in areas with edapho-climatic characteristics identical to those sustaining natural Lmj populations, and successful reproduction of the plant was achieved. The relevant conclusion from these assays was that the successful reproductive cycle was absolutely dependent on seedling inoculation with effective bradyrhizobia The forth topic deep into the analysis of the genomic of Lmj representative strains. To this end, draft genomic sequences of selected Lmj strains and type strains of Bradyrhizobium spp. were assembled. The comparison analysis of the draft genomic sequences of Lmj strains and related Bradyrhizobium species grouped in Clade I, revealed a high genomic homology among them, and allowed the definition of five potentially new species of Lmj nodulating bacteria. Also, based on the available draft genomic sequences, only three clusters of nod, fix and nif genes from Lmj strains were identified and showed to define a new symbiotic lineage, distant from that of B. canariense and B. japonicum bv. genistearum. The low diversity exhibited by the phylogenetic analysis of symbiotic genes contrast with the large diversity of strains as regards the housekeeping genes analyzed. Besides, the genomic analysis of a Lupinus angustifolius strain ISLU101, revealed the presence of an extrachromosomal replication origin homologous to repABC cluster from plasmid present in Bradyrhizobium spp BTAi1. This repABC cluster gene sequence allowed the identification of extrachromosomic replication origin in 19 out of 72 Bradyrhizobium strains from Lupinus spp., a highly significant result since the absence of plasmids in the Bradyrhizobium genus was traditionally assumed. The repABC gene sequences of these strains grouped them in a unique monophyletic group, related to B. sp. BTAi1 plasmid, but differentiated from the repABC gene cluster of plasmids in fast growing rhizobium strains. The last topic was focused on characterization of type III secreted effectors present in Lmj endosymbiotic bacteria. Type III secretion systems (T3SS) are specialized protein export machineries which can deliver effector proteins into plant cells. The presence of T3SS in rhizobia has frequently been related to the symbiotic nodulation host-range and may have a beneficial or detrimental effect on the symbiosis with legumes. In this context, the presence of T3SS in genomes of nine Lmj strains was investigated, and it was shown the presence of clusters encoding NopE type III-secreted protein similar to the NopE1 and NopE2 of B. diazoefficiens USDA 110T. The putative NopE protein of LmjC strain is at present being characterized regarding its structure and function.

On the testing of large PV arrays

This paper reports on the IES-UPM experience from 2006 to 2010 in the field of the characterization of PV arrays of commercial large PV plants installed in Spain within the framework of the profitable economic scenarios associated to feed-in tariff laws. This experience has extended to 200 MW and has provided valuable lessons to minimize uncertainty, which plays a key role in quality assurance procedures. The paper deals not only with classic I–V measurements but also with watt-metering-based procedures. Particular attention is paid to the selection of irradiance and cell temperature sensors

Assessment of the effects of ozone exposure and plant competition on the reproductive ability of three therophytic clover species from Iberian pastures

Ozone (O3) phytototoxicity has been reported on a wide range of crops and wild Central European plantspecies, however no information has been provided regarding the sensitivity of plantspecies from dehesa Mediterranean therophytic grasslands in spite of their great plantspecies richness and the high O3 levels that are recorded in this area. A study was carried out in open-top chambers (OTCs) to assess the effects of O3 and competition on the reproductiveability of threecloverspecies: Trifolium cherleri, Trifolium subterraneum and Trifolium striatum. A phytometer approach was followed, therefore plants of these species were grown in mesoscosms composed of monocultures of four plants of each species, of threeplants of each species competing against a Briza maxima individual or of a single plant of each cloverspecies competing with threeB. maximaplants. Three O3 treatments were adopted: charcoal filtered air (CFA), non-filtered air (NFA) and non-filtered air supplemented with 40 nl l−1 of O3 (NFA+). The different mesocosms were exposed to the different O3 treatments for 45 days and then they remained in the open. Ozoneexposure caused reductions in the flower biomass of the threecloverspecies assessed. In the case of T. cherleri and T. subterraneum this effect was found following their exposure to the different O3 treatments during their vegetative period. An attenuation of these effects was found when the plants remained in the open. Ozone-induced detrimental effects on the seed output of T. striatum were also observed. The flower biomass of the cloverplants grown in monocultures was greater than when competing with one or threeB. maxima individuals. An increased flower biomass was found in the CFA monoculture mesocosms of T. cherleri when compared with the remaining mesocosms, once the plants were exposed in the open for 60 days. The implications of these effects on the performance of dehesa acid grasslands and for the definition of O3 critical levels is discussed

Self-learning of fault diagnosis identification

A good and early fault detection and isolation system along with efficient alarm management and fine sensor validation systems are very important in today¿s complex process plants, specially in terms of safety enhancement and costs reduction. This paper presents a methodology for fault characterization. This is a self-learning approach developed in two phases. An initial, learning phase, where the simulation of process units, without and with different faults, will let the system (in an automated way) to detect the key variables that characterize the faults. This will be used in a second (on line) phase, where these key variables will be monitored in order to diagnose possible faults. Using this scheme the faults will be diagnosed and isolated in an early stage where the fault still has not turned into a failure.