Quality assurance systems in the production and marketing of fresh peaches.

Due to the fast rate of peach post-harvest ripening, damage due to mechanical handling, externally appreciated as bruises and soft areas, is a real problem that leads to an early harvesting and poor quality of the fruits, as perceived by the consumers. More and more, the European consumer asks for good taste and freshness of fruits and vegetables, and these quality factors are not included in standards, nor in most of the producers' practices. Fruit processing and marketing centres (co-operatives) are increasingly interested in adopting quality controls in their processes. ISO 9000 procedures are being applied in some food areas, primarily milk and meat processors, but no generalised procedures have been developed until the present time to be applied to fresh product processes. All different peach and nectarine varieties that are harvested and handled in Murcia cooperatives and sold in a large supermarket in Madrid were analysed during the whole 1997 season (early May to late August). A total number of 78 samples of 25 fruits (co-operative) or 10 fruits (market), were tested in the laboratory for mechanical, optical, chemical and tasting quality. The variability and relationships between all these quality parameters are presented and discussed, and sampling unit sizes which would be advisable for quality control are calculated.

Aplicación de la celulosa bacteriana a la restauración del patrimonio bibliográfico y documental en papel

La preservación del patrimonio bibliográfico y documental en papel es uno de los mayores retos a los que se enfrentan bibliotecas y archivos de todo el mundo. La búsqueda de soluciones al problema del papel degradado ha sido abordada históricamente desde dos líneas de trabajo predominantes: la conservación de estos documentos mediante la neutralización de los ácidos presentes en ellos con agentes alcalinos, y su restauración mediante el método de laminación fundamentalmente con papel de origen vegetal. Sin embargo, no se ha explorado con éxito la posibilidad de reforzar la celulosa dañada, y el problema sigue sin encontrar una solución satisfactoria. Hasta el día de hoy, el desarrollo de tratamientos basados en biotecnología en la conservación del patrimonio documental ha sido muy escaso, aunque la capacidad de ciertas bacterias de producir celulosa lleva a plantear su uso en el campo de la conservación y restauración del papel. La celulosa bacteriana (CB) es químicamente idéntica a la celulosa vegetal, pero su organización macroscópica es diferente. Sus propiedades únicas (alto grado de cristalinidad, durabilidad, resistencia y biocompatibilidad) han hecho de este material un excelente recurso en diferentes campos. En el desarrollo de esta tesis se ha estudiado el uso de la celulosa bacteriana, de alta calidad, generada por Gluconacetobacter sucrofermentans CECT 7291, para restaurar documentos deteriorados y consolidar los que puedan estar en peligro de degradación, evitando así su destrucción y proporcionando al papel que se restaura unas buenas propiedades mecánicas, ópticas y estructurales. Se desarrollan asimismo protocolos de trabajo que permitan la aplicación de dicha celulosa. En primer lugar se seleccionó el medio de cultivo que proporcionó una celulosa adecuada para su uso en restauración. Para ello se evaluó el efecto que tienen sobre la celulosa generada las fuentes de carbono y nitrógeno del medio de cultivo, manteniendo como parámetros fijos la temperatura y el pH inicial del medio, y efectuando los ensayos en condiciones estáticas. Se evaluó, también, el efecto que tiene en la CB la adición de un 1% de etanol al medio de cultivo. Las capas de celulosa se recolectaron a cuatro tiempos distintos, caracterizando en cada uno de ellos el medio de cultivo (pH y consumo de fuente de carbono), y las capas de CB (pH, peso seco y propiedades ópticas y mecánicas). La mejor combinación de fuentes de carbono y nitrógeno resultó ser fructosa más extracto de levadura y extracto de maíz, con o sin etanol, que proporcionaban una buena relación entre la producción de celulosa y el consumo de fuente de carbono, y que generaban una capa de celulosa resistente y homogénea. La adición de etanol al medio de cultivo, si bien aumentaba la productividad, causaba un descenso apreciable de pH. Las capas de CB obtenidas con los medios de cultivo optimizados se caracterizaron en términos de sus índices de desgarro y estallido, propiedades ópticas, microscopía electrónica de barrido (SEM), difracción de rayos-X, espectroscopía infrarroja con transformada de Fourier (FTIR), grado de polimerización, ángulos de contacto estáticos y dinámicos, y porosimetría de intrusión de mercurio. Por otro lado hay que tener en cuenta que el material restaurado debe ser estable con el tiempo. Por ello esta misma caracterización se efectuó tras someter a las capas de CB a un proceso de envejecimiento acelerado. Los resultados mostraron que la CB resultante tiene un elevado índice de cristalinidad, baja porosidad interna, buenas propiedades mecánicas, y alta estabilidad en el tiempo. Para desarrollar los protocolos de trabajo que permitan la restauración con esta celulosa optimizada, se comienzó con un proceso de selección de los papeles que van a ser restaurados. Se eligieron tres tipos de papeles modelo, hechos con pasta mecánica, química y filtro (antes y después de ser sometidos a un proceso de envejecimiento acelerado), y tres libros viejos adquiridos en el mercado de segunda mano. Estos ejemplares a restaurar se caracterizaron también en términos de sus propiedades mecánicas y fisicoquímicas. El primer protocolo de restauración con CB que se evaluó fue el denominado laminación. Consiste en aplicar un material de refuerzo al documento mediante el uso de un adhesivo. Se seleccionó para ello la CB producida en el medio de cultivo optimizado con un 1% de etanol. Se aplicó un método de purificación alcalino (1 hora a 90 °C en NaOH al 1%) y como adhesivo se seleccionó almidón de trigo. El proceso de laminación se efectuó también con papel japonés (PJ), un material habitualmente utilizado en conservación, para comparar ambos materiales. Se concluyó que no hay diferencias significativas en las características estudiadas entre los dos tipos de materiales de refuerzo. Se caracterizó el material reforzado y, también, después de sufrir un proceso de envejecimiento acelerado. Los papeles laminados con CB mostraban diferencias más marcadas en las propiedades ópticas que los restaurados con PJ, con respecto a los originales. Sin embargo, el texto era más legible cuando el material de restauración era la CB. La mojabilidad disminuía con ambos tipos de refuerzo, aunque en los papeles laminados con CB de manera más marcada e independiente del material a restaurar. Esto se debe a la estructura cerrada de la CB, que también conduce a una disminución en la permeabilidad al aire. Este estudio sugiere que la CB mejora la calidad del papel deteriorado, sin alterar la información que contiene, y que esta mejora se mantiene a lo largo del tiempo. Por tanto, la CB puede ser utilizada como material de refuerzo para laminar, pudiendo ser más adecuada que el PJ para ciertos tipos de papeles. El otro método de restauración que se estudió fue la generación in situ de la CB sobre el papel a restaurar. Para ello se seleccionó el medio de cultivo sin etanol, ya que el descenso de pH que causaba su presencia podría dañar el documento a restaurar. El método de purificación elegido fue un tratamiento térmico (24 horas a 65 °C), menos agresivo para el material a restaurar que el tratamiento alcalino. Se seleccionó la aplicación del medio de cultivo con la bacteria mediante pincel sobre el material a restaurar. Una vez caracterizado el material restaurado, y éste mismo tras sufrir un proceso de envejecimiento acelerado, se concluyó que no hay modificación apreciable en ninguna característica, salvo en la permeabilidad al aire, que disminuye de manera muy evidente con la generación de CB, dando lugar a un material prácticamente impermeable al aire. En general se puede concluir que ha quedado demostrada la capacidad que tiene la celulosa generada por la bacteria Gluconacetobacter sucrofermentans CECT 7291 para ser utilizada como material de refuerzo en la restauración del patrimonio documental en papel. Asimismo se han desarrollado dos métodos de aplicación, uno ex situ y otro in situ, para efectuar esta tarea de restauración. ABSTRACT The preservation of bibliographic and documentary heritage is one of the biggest challenges that libraries and archives around the world have to face. The search for solutions to the problem of degraded paper has historically been focused from two predominants lines of work: the conservation of these documents by the neutralization of acids in them with alkaline agents, and their restoration by lining them with, basically, cellulose from vegetal sources. However, the possibility of strengthening the damaged cellulose has not been successfully explored, and the problem still persists. Until today, the development of biotechnology-based treatments in documentary heritage conservation has been scarce, although the ability of certain bacteria to produce cellulose takes to propose its use in the field of conservation and restoration of paper. The bacterial cellulose (BC) is chemically identical to the plant cellulose, but its macroscopic organization is different. Its unique properties (high degree of crystallinity, durability, strength and biocompatibility), makes it an excellent resource in different fields. The use of high-quality BC generated by Gluconacetobacter sucrofermentans CECT 7291 to restore damaged documents and to consolidate those that may be at risk of degradation, has been studied in this thesis, trying to prevent the document destruction, and to get reinforced papers with good mechanical, optical and structural properties. Protocols that allow the implementation of the BC as a reinforcing material were also developed. First of all, in order to select the culture medium that provides a cellulose suitable for its use in restoration, it has been evaluated the effect that the carbon and nitrogen sources from the culture medium have on the generated BC, keeping the temperature and the initial pH of the medium as fixed parameters, and performing the culture without shaking. The effect of the addition of 1% ethanol to the culture medium on BC properties was also evaluated. The cellulose layers were collected at four different times, characterizing in all of them the culture medium (pH and carbon source consumption), and the BC sheets (pH, dry weight and optical and mechanical properties). The best combination of carbon and nitrogen sources proved to be fructose plus yeast extract and corn steep liquor, with or without ethanol, which provided a good balance between the cellulose production and the consumption of carbon source, and generating BC sheets homogeneous and resistant. The addition of ethanol to the culture medium increased productivity but caused a noticeable decrement in pH. The BC layers generated with these optimized culture media, have been characterized in terms of tear and burst index, optical properties, scanning electron microscopy (SEM), X-ray diffraction, infrared Fourier transform spectroscopy (FTIR), polymerization degree, static and dynamic contact angles, and mercury intrusion porosimetry. Moreover it must be kept in mind that the restored materials should be stable over time. Therefore, the same characterization was performed after subjecting the layers of BC to an accelerated aging process. The results showed that the BC sheets obtained have a high crystallinity index, low internal porosity, good mechanical properties, and high stability over time. To develop working protocols to use this optimized BC in paper restoration, the first step was to select the samples to restore. Three types of model papers, made from mechanical pulp, chemical pulp and filter paper (before and after an accelerated aging process), and three old books purchased in the second hand market, were chosen. These specimens to be restored were also characterized in terms of its mechanical and physicochemical properties. The first protocol of restoration with BC to be evaluated is called linning. It consists on applying a reinforcing material to the document using an adhesive. The BC produced in the optimized culture medium with 1% ethanol was selected. An alkali purification method (1 hour at 90 °C in 1% NaOH) was applied, and wheat starch was selected as adhesive. The linning process was also carried out with Japanese paper (JP), a material commonly used in conservation, in order to compare both materials. It was concluded that there are no significant differences in the characteristics studied of the two types of reinforcing materials. The reinforced materials were characterized before and after undergoing to an accelerated aging. Papers lined with BC showed more marked differences in the optical properties that papers restored with JP. However, the text was more readable when BC was the reinforcing material. Wettability decreased with both types of reinforcement, although in the papers linned with BC it happened more marked and independently of the sample to restore. This is due to the closed structure of BC, which also leads to a decrement in air permeance. This study suggests that BC improves the deteriorated paper quality, without altering the information on it, and that this improvement is maintained over time. Therefore, the BC may be used as reinforcing material for linning, being more suitable than the JP to restore certain types of papers. The other restoration method to be evaluated was the in situ generation of BC over the paper to restore. For this purpose the culture medium without ethanol was selected, as the pH decrement caused by his presence would damage the document to restore. As purification method a heat treatment (24 hours at 65 °C) was chosen, less aggressive to the material to restore than the alkaline treatment. It was decided to apply the culture medium with the bacteria onto the material to restore with a brush. The reinforced material was characterized before and after an accelerated aging process. It was concluded that there was no substantial change in any characteristic, except for air permeance, which decreases very sharply after the generation of BC, getting a substantially air impermeable material. In general, it can be concluded that the ability of BC produced by Gluconacetobacter sucrofermentans CECT 7291 for its use as a reinforcing material in the restoration of paper documentary heritage, has been demonstrated. Also, two restoration methods, one ex situ and another in situ have been developed.

Thermal and mechanical effects of different excitation modes based on low frequency laser modulation in optical hyperthermia

The low frequency modulation of the laser source (menor que30KHz) allows the generation of a pulsed signal that intermittently excites the gold nanorods. The temperature curves obtained for different frequencies and duty cycles of modulation but with equal average power and identical laser parameters, show that the thermal behavior in continuous wave and modulation modes is the same. However, the cell death experiments suggest that the percentage of death is higher in the cases of modulation. This observation allows us to conclude that there are other effects in addition to temperature that contribute to the cellular death. The mechanical effects like sound or pressure waves are expected to be generated from thermal expansion of gold nanorods. In order to study the behavior and magnitude of these processes we have developed a measure device based on ultrasound piezoelectric receivers (25KHz) and a lock-in amplifier that is able to detect the sound waves generated in samples of gold nanorods during laser irradiation providing us a voltage result proportional to the pressure signal. The first results show that the pressure measurements are directly proportional to the concentration of gold nanorods and the laser power, therefore, our present work is focused on determine the real influence of these effects in the cell death process.

Instrumental quality assessment of fresh peaches: Optical and mechanical parameters.

In developing instrumentation for the measurement of fruit quality, there is the need for fast and non-destructive devices, based on sensors, to be installed on-line. In the case of some fruits, like peaches, post-harvest ripeness, which is closely related to high quality for the consumer, is a priority. During ripening, external appearance (colour) and internal mechanical (firmness) and chemical (sugars and acids) quality are main features that evolve rapidly from and unripe to a ripe (high quality) stage. When considering the evolution of fruit quality in this scheme, external colour and firmness are shown to evolve in a parallel pattern, if monitored from the time of harvest to full consumer ripeness ( Rood, 1957; Crisosto et al, 1995; Kader, 1996). The visible (VIS) reflectance spectrum is a fast and easy reference that can be used to estimate quality of peaches, if we could show it to be reliably correlated with peach ripening rate during postharvest (Genard et al. 1994; Moras, 1995; Delwiche and Baumgartner, 1983; Delwiche et al. 1987; Slaughter, 1995; Lleo et al., 1998). Taste, described as an expert acceptance score, improves with ripeness (firmness and colour evolution), when considering the fruits on the tree, and also post-harvest.

Tunable mechanical resonator with aluminum nitride piezoelectric

The electromechanical response of piezoelectrically-actuated AlN micromachined bridge resonators has been characterized using laser interferometry and electrical admittance measurements. We compare the response of microbridges with different dimensions and buckling (induced by the initial residual stress of the layers). The resonance frequencies are in good agreement with numerical simulations of the electromechanical behavior of the structures. We show that it is possible to perform a rough tuning of the resonance frequencies by allowing a determined amount of builtin stress in the microbridge during its fabrication. Once the resonator is made, a DC bias added to the AC excitation signal allows to fine-tune the frequency. Our microbridges yield a tuning factor of around 88 Hz/V for a 500 ?m-long microbridge.

Curing, defects and mechanical performance of fiber-reinforced composites

Tradicionalmente, la fabricación de materiales compuestos de altas prestaciones se lleva a cabo en autoclave mediante la consolidación de preimpregnados a través de la aplicación simultánea de altas presiones y temperatura. Las elevadas presiones empleadas en autoclave reducen la porosidad de los componentes garantizando unas buenas propiedades mecánicas. Sin embargo, este sistema de fabricación conlleva tiempos de producción largos y grandes inversiones en equipamiento lo que restringe su aplicación a otros sectores alejados del sector aeronáutico. Este hecho ha generado una creciente demanda de sistemas de fabricación alternativos al autoclave. Aunque estos sistemas son capaces de reducir los tiempos de producción y el gasto energético, por lo general, dan lugar a materiales con menores prestaciones mecánicas debido a que se reduce la compactación del material al aplicar presiones mas bajas y, por tanto, la fracción volumétrica de fibras, y disminuye el control de la porosidad durante el proceso. Los modelos numéricos existentes permiten conocer los fundamentos de los mecanismos de crecimiento de poros durante la fabricación de materiales compuestos de matriz polimérica mediante autoclave. Dichos modelos analizan el comportamiento de pequeños poros esféricos embebidos en una resina viscosa. Su validez no ha sido probada, sin embargo, para la morfología típica observada en materiales compuestos fabricados fuera de autoclave, consistente en poros cilíndricos y alargados embebidos en resina y rodeados de fibras continuas. Por otro lado, aunque existe una clara evidencia experimental del efecto pernicioso de la porosidad en las prestaciones mecánicas de los materiales compuestos, no existe información detallada sobre la influencia de las condiciones de procesado en la forma, fracción volumétrica y distribución espacial de los poros en los materiales compuestos. Las técnicas de análisis convencionales para la caracterización microestructural de los materiales compuestos proporcionan información en dos dimensiones (2D) (microscopía óptica y electrónica, radiografía de rayos X, ultrasonidos, emisión acústica) y sólo algunas son adecuadas para el análisis de la porosidad. En esta tesis, se ha analizado el efecto de ciclo de curado en el desarrollo de los poros durante la consolidación de preimpregnados Hexply AS4/8552 a bajas presiones mediante moldeo por compresión, en paneles unidireccionales y multiaxiales utilizando tres ciclos de curado diferentes. Dichos ciclos fueron cuidadosamente diseñados de acuerdo a la caracterización térmica y reológica de los preimpregnados. La fracción volumétrica de poros, su forma y distribución espacial se analizaron en detalle mediante tomografía de rayos X. Esta técnica no destructiva ha demostrado su capacidad para analizar la microestructura de materiales compuestos. Se observó, que la porosidad depende en gran medida de la evolución de la viscosidad dinámica a lo largo del ciclo y que la mayoría de la porosidad inicial procedía del aire atrapado durante el apilamiento de las láminas de preimpregnado. En el caso de los laminados multiaxiales, la porosidad también se vio afectada por la secuencia de apilamiento. En general, los poros tenían forma cilíndrica y se estaban orientados en la dirección de las fibras. Además, la proyección de la población de poros a lo largo de la dirección de la fibra reveló la existencia de una estructura celular de un diámetro aproximado de 1 mm. Las paredes de las celdas correspondían con regiones con mayor densidad de fibra mientras que los poros se concentraban en el interior de las celdas. Esta distribución de la porosidad es el resultado de una consolidación no homogenea. Toda esta información es crítica a la hora de optimizar las condiciones de procesado y proporcionar datos de partida para desarrollar herramientas de simulación de los procesos de fabricación de materiales compuestos fuera de autoclave. Adicionalmente, se determinaron ciertas propiedades mecánicas dependientes de la matriz termoestable con objeto de establecer la relación entre condiciones de procesado y las prestaciones mecánicas. En el caso de los laminados unidireccionales, la resistencia interlaminar depende de la porosidad para fracciones volumétricas de poros superiores 1%. Las mismas tendencias se observaron en el caso de GIIc mientras GIc no se vio afectada por la porosidad. En el caso de los laminados multiaxiales se evaluó la influencia de la porosidad en la resistencia a compresión, la resistencia a impacto a baja velocidad y la resistencia a copresión después de impacto. La resistencia a compresión se redujo con el contenido en poros, pero éste no influyó significativamente en la resistencia a compresión despues de impacto ya que quedó enmascarada por otros factores como la secuencia de apilamiento o la magnitud del daño generado tras el impacto. Finalmente, el efecto de las condiciones de fabricación en el proceso de compactación mediante moldeo por compresión en laminados unidireccionales fue simulado mediante el método de los elementos finitos en una primera aproximación para simular la fabricación de materiales compuestos fuera de autoclave. Los parámetros del modelo se obtuvieron mediante experimentos térmicos y reológicos del preimpregnado Hexply AS4/8552. Los resultados obtenidos en la predicción de la reducción de espesor durante el proceso de consolidación concordaron razonablemente con los resultados experimentales. Manufacturing of high performance polymer-matrix composites is normally carried out by means of autoclave using prepreg tapes stacked and consolidated under the simultaneous application of pressure and temperature. High autoclave pressures reduce the porosity in the laminate and ensure excellent mechanical properties. However, this manufacturing route is expensive in terms of capital investment and processing time, hindering its application in many industrial sectors. This fact has driven the demand of alternative out-of-autoclave processing routes. These techniques claim to produce composite parts faster and at lower cost but the mechanical performance is also reduced due to the lower fiber content and to the higher porosity. Corrient numerical models are able to simulate the mechanisms of void growth in polymer-matrix composites processed in autoclave. However these models are restricted to small spherical voids surrounded by a viscous resin. Their validity is not proved for long cylindrical voids in a viscous matrix surrounded by aligned fibers, the standard morphology observed in out-of-autoclave composites. In addition, there is an experimental evidence of the detrimental effect of voids on the mechanical performance of composites but, there is detailed information regarding the influence of curing conditions on the actual volume fraction, shape and spatial distribution of voids within the laminate. The standard techniques of microstructural characterization of composites (optical or electron microscopy, X-ray radiography, ultrasonics) provide information in two dimensions and are not always suitable to determine the porosity or void population. Moreover, they can not provide 3D information. The effect of curing cycle on the development of voids during consolidation of AS4/8552 prepregs at low pressure by compression molding was studied in unidirectional and multiaxial panels. They were manufactured using three different curing cycles carefully designed following the rheological and thermal analysis of the raw prepregs. The void volume fraction, shape and spatial distribution were analyzed in detail by means of X-ray computed microtomography, which has demonstrated its potential for analyzing the microstructural features of composites. It was demonstrated that the final void volume fraction depended on the evolution of the dynamic viscosity throughout the cycle. Most of the initial voids were the result of air entrapment and wrinkles created during lay-up. Differences in the final void volume fraction depended on the processing conditions for unidirectional and multiaxial panels. Voids were rod-like shaped and were oriented parallel to the fibers and concentrated in channels along the fiber orientation. X-ray computer tomography analysis of voids along the fiber direction showed a cellular structure with an approximate cell diameter of 1 mm. The cell walls were fiber-rich regions and porosity was localized at the center of the cells. This porosity distribution within the laminate was the result of inhomogeneous consolidation. This information is critical to optimize processing parameters and to provide inputs for virtual testing and virtual processing tools. In addition, the matrix-controlled mechanical properties of the panels were measured in order to establish the relationship between processing conditions and mechanical performance. The interlaminar shear strength (ILSS) and the interlaminar toughness (GIc and GIIc) were selected to evaluate the effect of porosity on the mechanical performance of unidirectional panels. The ILSS was strongly affected by the porosity when the void contents was higher than 1%. The same trends were observed in the case of GIIc while GIc was insensitive to the void volume fraction. Additionally, the mechanical performance of multiaxial panels in compression, low velocity impact and compression after impact (CAI) was measured to address the effect of processing conditions. The compressive strength decreased with porosity and ply-clustering. However, the porosity did not influence the impact resistance and the coompression after impact strength because the effect of porosity was masked by other factors as the damage due to impact or the laminate lay-up. Finally, the effect of the processing conditions on the compaction behavior of unidirectional AS4/8552 panels manufactured by compression moulding was simulated using the finite element method, as a first approximation to more complex and accurate models for out-of autoclave curing and consolidation of composite laminates. The model parameters were obtained from rheological and thermo-mechanical experiments carried out in raw prepreg samples. The predictions of the thickness change during consolidation were in reasonable agreement with the experimental results.

Laser shock peening without absorbent coating (LSPwC) effect on 3D surface topography and mechanical properties of 6082-T651 Al alloy

The influence of nanosecond laser pulses applied by laser shock peening without absorbent coating (LSPwC) with a Q-switched Nd:YAG laser operating at a wavelength of λ = 1064 nm on 6082-T651 Al alloy has been investigated. The first portion of the present study assesses laser shock peening effect at two pulse densities on three-dimensional (3D) surface topography characteristics. In the second part of the study, the peening effect on surface texture orientation and micro-structure modification, i.e. the effect of surface craters due to plasma and shock waves, were investigated in both longitudinal (L) and transverse (T) directions of the laser-beam movement. In the final portion of the study, the changes of mechanical properties were evaluated with a residual stress profile and Vickers micro-hardness through depth variation in the near surface layer, whereas factorial design with a response surface methodology (RSM) was applied. The surface topographic and micro-structural effect of laser shock peening were characterised with optical microscopy, InfiniteFocus® microscopy and scanning electron microscopy (SEM). Residual stress evaluation based on a hole-drilling integral method confirmed higher compression at the near surface layer (33 μm) in the transverse direction (σmin) of laser-beam movement, i.e. − 407 ± 81 MPa and − 346 ± 124 MPa, after 900 and 2500 pulses/cm2, respectively. Moreover, RSM analysis of micro-hardness through depth distribution confirmed an increase at both pulse densities, whereas LSPwC-generated shock waves showed the impact effect of up to 800 μm below the surface. Furthermore, ANOVA results confirmed the insignificant influence of LSPwC treatment direction on micro-hardness distribution indicating essentially homogeneous conditions, in both L and T directions.

Crack mechanical failure in lithium niobate crystal under ion irradiation; novel simulation by extended finite elements

Swift heavy ion irradiation (ions with mass heavier than 15 and energy exceeding MeV/amu) transfer their energy mainly to the electronic system with small momentum transfer per collision. Therefore, they produce linear regions (columnar nano-tracks) around the straight ion trajectory, with marked modifications with respect to the virgin material, e.g., phase transition, amorphization, compaction, changes in physical or chemical properties. In the case of crystalline materials the most distinctive feature of swift heavy ion irradiation is the production of amorphous tracks embedded in the crystal. Lithium niobate is a relevant optical material that presents birefringence due to its anysotropic trigonal structure. The amorphous phase is certainly isotropic. In addition, its refractive index exhibits high contrast with those of the crystalline phase. This allows one to fabricate waveguides by swift ion irradiation with important technological relevance. From the mechanical point of view, the inclusion of an amorphous nano-track (with a density 15% lower than that of the crystal) leads to the generation of important stress/strain fields around the track. Eventually these fields are the origin of crack formation with fatal consequences for the integrity of the samples and the viability of the method for nano-track formation. For certain crystal cuts (X and Y), these fields are clearly anisotropic due to the crystal anisotropy. We have used finite element methods to calculate the stress/strain fields that appear around the ion-generated amorphous nano-tracks for a variety of ion energies and doses. A very remarkable feature for X cut-samples is that the maximum shear stress appears on preferential planes that form +/-45º with respect to the crystallographic planes. This leads to the generation of oriented surface cracks when the dose increases. The growth of the cracks along the anisotropic crystal has been studied by means of novel extended finite element methods, which include cracks as discontinuities. In this way we can study how the length and depth of a crack evolves as function of the ion dose. In this work we will show how the simulations compare with experiments and their application in materials modification by ion irradiation.

Crack mechanical failure in ceramic materials under ion irradiation: case of lithium niobate crystal

Swift heavy ion irradiation (ions with mass heavier than 15 and energy exceeding MeV/amu) transfer their energy mainly to the electronic system with small momentum transfer per collision. Therefore, they produce linear regions (columnar nano-tracks) around the straight ion trajectory, with marked modifications with respect to the virgin material, e.g., phase transition, amorphization, compaction, changes in physical or chemical properties. In the case of crystalline materials the most distinctive feature of swift heavy ion irradiation is the production of amorphous tracks embedded in the crystal. Lithium niobate is a relevant optical material that presents birefringence due to its anysotropic trigonal structure. The amorphous phase is certainly isotropic. In addition, its refractive index exhibits high contrast with those of the crystalline phase. This allows one to fabricate waveguides by swift ion irradiation with important technological relevance. From the mechanical point of view, the inclusion of an amorphous nano-track (with a density 15% lower than that of the crystal) leads to the generation of important stress/strain fields around the track. Eventually these fields are the origin of crack formation with fatal consequences for the integrity of the samples and the viability of the method for nano-track formation. For certain crystal cuts (X and Y), these fields are clearly anisotropic due to the crystal anisotropy. We have used finite element methods to calculate the stress/strain fields that appear around the ion- generated amorphous nano-tracks for a variety of ion energies and doses. A very remarkable feature for X cut-samples is that the maximum shear stress appears on preferential planes that form +/-45º with respect to the crystallographic planes. This leads to the generation of oriented surface cracks when the dose increases. The growth of the cracks along the anisotropic crystal has been studied by means of novel extended finite element methods, which include cracks as discontinuities. In this way we can study how the length and depth of a crack evolves as function of the ion dose. In this work we will show how the simulations compare with experiments and their application in materials modification by ion irradiation.

Tailoring the Optical Properties of Silica Irradiated with Swift Heavy Ions

Irradiation with swift heavy ions (SHI), roughly defined as those having atomic masses larger than 15 and energies exceeding 1 MeV/amu, may lead to significant modification of the irradiated material in a nanometric region around the (straight) ion trajectory (i.e., latent tracks). In the case of amorphous silica it has been reported that SHI irradiation originates nano-tracks of either higher density than the virgin material (for low electronic stopping powers, Se < 7 keV/nm) [1] or having a low-density core and a dense shell (Se > 12 keV/nm) [2]. The intermediate region has not been studied in detail but we will show in this work that essentially no changes in density occur in this zone. An interesting effect of the compaction is that the refractive index is increased with respect to that of the surroundings. In the first Se region it is clear that track overlapping leads to continuous amorphous layers that present a significant contrast with respect to the pristine substrate and this has been used to produce optical waveguides. The optical effects of intermediate and high stopping powers, on the other hand, are largely unknown so far. In this work we have studied theoretically (molecular dynamics and optical simulations) and experimentally (irradiation with SHI and optical characterization) the dependence of the macroscopic optical properties (i.e., the refractive index of the effective medium, n_EMA) on the electronic stopping power of the incoming ions. Our results show that the refractive index of the irradiated silica is not increased in the intermediate region, as expected; however, the core-shell tracks of the high-Se region produce a quite effective enhancement of n_EMA that could prove attractive for the fabrication of optical waveguides at ultralow fluences (as low as 1E11 cm^-2). 1. J. Manzano, J. Olivares, F. Agulló-López, M. L. Crespillo, A. Moroño, and E. Hodgson, "Optical waveguides obtained by swift-ion irradiation on silica (a-SiO2)," Nucl. Instrum. Meth. B 268, 3147-3150 (2010). 2. P. Kluth, C. S. Schnohr, O. H. Pakarinen, F. Djurabekova, D. J. Sprouster, R. Giulian, M. C. Ridgway, A. P. Byrne, C. Trautmann, D. J. Cookson, K. Nordlund, and M. Toulemonde, "Fine structure in swift heavy ion tracks in amorphous SiO2," Phys. Rev. Lett. 101, 175503 (2008).

Sensing and modelling mechanical properties of fruits for quality.

Nondestructive techniques are extensively researched for the measurement of physical properties of fruits related to quality. Optical properties can be applied mainly in the detection of those quality features which are related to the chemical composition of the fruit, color (in the VIS region) or chemical constituents (sugar, in the MR region) being the most important. The most relevant mechanical property of fruits is consistency, generally called firmness, and to date only techniques which are able to measure the mechanical properties of the fruit bulk tissue are used for its prediction. Fruits can be modelled as elastic bodies, or at least as partially elastic. Therefore, the measurement of some elastic constants of the fruit can be used for the evaluation of its firmness. The differences in the response to loading are relevant in studying a) fruit firmness and b) bruising susceptibility. Both have been modelled for selected fruit species and varieties.

Mechanical Characterization of Tungsten-Titanium-Lanthana alloy: Influence of Temperature and Atmosphere

The target is to evaluate the mechanical behavior of Ti and La2O3 dispersed W alloy, processed by HIP and compare it with a reference pure-W. Tests were performed in both oxidant (air) and inert (vacuum) atmosphere in a temperature range from -196 to 1200 °C.

High isolation series-shunt photoconductive microwave switch

This article presents a wide band compact high isolation photoconductive switch, which is based on the series-shunt switch design with three photoconductive switches made of diced high-resistivity silicon wafer placed over a microstrip gap and activated by 808-nm near-infrared laser diodes. The switch shows an insertion loss of 1.2 dB and an isolation of 44.8 dB at 2 GHz. It is easy to operate and control by light, high-speed, electromagnetically transparent and it does not require any biasing circuits.

Microstructure-based numerical modeling of the mechanical behavior of Mg alloys

Dentro de los materiales estructurales, el magnesio y sus aleaciones están siendo el foco de una de profunda investigación. Esta investigación está dirigida a comprender la relación existente entre la microestructura de las aleaciones de Mg y su comportamiento mecánico. El objetivo es optimizar las aleaciones actuales de magnesio a partir de su microestructura y diseñar nuevas aleaciones. Sin embargo, el efecto de los factores microestructurales (como la forma, el tamaño, la orientación de los precipitados y la morfología de los granos) en el comportamiento mecánico de estas aleaciones está todavía por descubrir. Para conocer mejor de la relación entre la microestructura y el comportamiento mecánico, es necesaria la combinación de técnicas avanzadas de caracterización experimental como de simulación numérica, a diferentes longitudes de escala. En lo que respecta a las técnicas de simulación numérica, la homogeneización policristalina es una herramienta muy útil para predecir la respuesta macroscópica a partir de la microestructura de un policristal (caracterizada por el tamaño, la forma y la distribución de orientaciones de los granos) y el comportamiento del monocristal. La descripción de la microestructura se lleva a cabo mediante modernas técnicas de caracterización (difracción de rayos X, difracción de electrones retrodispersados, así como con microscopia óptica y electrónica). Sin embargo, el comportamiento del cristal sigue siendo difícil de medir, especialmente en aleaciones de Mg, donde es muy complicado conocer el valor de los parámetros que controlan el comportamiento mecánico de los diferentes modos de deslizamiento y maclado. En la presente tesis se ha desarrollado una estrategia de homogeneización computacional para predecir el comportamiento de aleaciones de magnesio. El comportamiento de los policristales ha sido obtenido mediante la simulación por elementos finitos de un volumen representativo (RVE) de la microestructura, considerando la distribución real de formas y orientaciones de los granos. El comportamiento del cristal se ha simulado mediante un modelo de plasticidad cristalina que tiene en cuenta los diferentes mecanismos físicos de deformación, como el deslizamiento y el maclado. Finalmente, la obtención de los parámetros que controlan el comportamiento del cristal (tensiones críticas resueltas (CRSS) así como las tasas de endurecimiento para todos los modos de maclado y deslizamiento) se ha resuelto mediante la implementación de una metodología de optimización inversa, una de las principales aportaciones originales de este trabajo. La metodología inversa pretende, por medio del algoritmo de optimización de Levenberg-Marquardt, obtener el conjunto de parámetros que definen el comportamiento del monocristal y que mejor ajustan a un conjunto de ensayos macroscópicos independientes. Además de la implementación de la técnica, se han estudiado tanto la objetividad del metodología como la unicidad de la solución en función de la información experimental. La estrategia de optimización inversa se usó inicialmente para obtener el comportamiento cristalino de la aleación AZ31 de Mg, obtenida por laminado. Esta aleación tiene una marcada textura basal y una gran anisotropía plástica. El comportamiento de cada grano incluyó cuatro mecanismos de deformación diferentes: deslizamiento en los planos basal, prismático, piramidal hc+ai, junto con el maclado en tracción. La validez de los parámetros resultantes se validó mediante la capacidad del modelo policristalino para predecir ensayos macroscópicos independientes en diferentes direcciones. En segundo lugar se estudió mediante la misma estrategia, la influencia del contenido de Neodimio (Nd) en las propiedades de una aleación de Mg-Mn-Nd, obtenida por extrusión. Se encontró que la adición de Nd produce una progresiva isotropización del comportamiento macroscópico. El modelo mostró que este incremento de la isotropía macroscópica era debido tanto a la aleatoriedad de la textura inicial como al incremento de la isotropía del comportamiento del cristal, con valores similares de las CRSSs de los diferentes modos de deformación. Finalmente, el modelo se empleó para analizar el efecto de la temperatura en el comportamiento del cristal de la aleación de Mg-Mn-Nd. La introducción en el modelo de los efectos non-Schmid sobre el modo de deslizamiento piramidal hc+ai permitió capturar el comportamiento mecánico a temperaturas superiores a 150_C. Esta es la primera vez, de acuerdo con el conocimiento del autor, que los efectos non-Schmid han sido observados en una aleación de Magnesio. The study of Magnesium and its alloys is a hot research topic in structural materials. In particular, special attention is being paid in understanding the relationship between microstructure and mechanical behavior in order to optimize the current alloy microstructures and guide the design of new alloys. However, the particular effect of several microstructural factors (precipitate shape, size and orientation, grain morphology distribution, etc.) in the mechanical performance of a Mg alloy is still under study. The combination of advanced characterization techniques and modeling at several length scales is necessary to improve the understanding of the relation microstructure and mechanical behavior. Respect to the simulation techniques, polycrystalline homogenization is a very useful tool to predict the macroscopic response from polycrystalline microstructure (grain size, shape and orientation distributions) and crystal behavior. The microstructure description is fully covered with modern characterization techniques (X-ray diffraction, EBSD, optical and electronic microscopy). However, the mechanical behaviour of single crystals is not well-known, especially in Mg alloys where the correct parameterization of the mechanical behavior of the different slip/twin modes is a very difficult task. A computational homogenization framework for predicting the behavior of Magnesium alloys has been developed in this thesis. The polycrystalline behavior was obtained by means of the finite element simulation of a representative volume element (RVE) of the microstructure including the actual grain shape and orientation distributions. The crystal behavior for the grains was accounted for a crystal plasticity model which took into account the physical deformation mechanisms, e.g. slip and twinning. Finally, the problem of the parametrization of the crystal behavior (critical resolved shear stresses (CRSS) and strain hardening rates of all the slip and twinning modes) was obtained by the development of an inverse optimization methodology, one of the main original contributions of this thesis. The inverse methodology aims at finding, by means of the Levenberg-Marquardt optimization algorithm, the set of parameters defining crystal behavior that best fit a set of independent macroscopic tests. The objectivity of the method and the uniqueness of solution as function of the input information has been numerically studied. The inverse optimization strategy was first used to obtain the crystal behavior of a rolled polycrystalline AZ31 Mg alloy that showed a marked basal texture and a strong plastic anisotropy. Four different deformation mechanisms: basal, prismatic and pyramidal hc+ai slip, together with tensile twinning were included to characterize the single crystal behavior. The validity of the resulting parameters was proved by the ability of the polycrystalline model to predict independent macroscopic tests on different directions. Secondly, the influence of Neodymium (Nd) content on an extruded polycrystalline Mg-Mn-Nd alloy was studied using the same homogenization and optimization framework. The effect of Nd addition was a progressive isotropization of the macroscopic behavior. The model showed that this increase in the macroscopic isotropy was due to a randomization of the initial texture and also to an increase of the crystal behavior isotropy (similar values of the CRSSs of the different modes). Finally, the model was used to analyze the effect of temperature on the crystal behaviour of a Mg-Mn-Nd alloy. The introduction in the model of non-Schmid effects on the pyramidal hc+ai slip allowed to capture the inverse strength differential that appeared, between the tension and compression, above 150_C. This is the first time, to the author's knowledge, that non-Schmid effects have been reported for Mg alloys.

Microstructural and mechanical characterization of annealed tungsten (W) and potassium-doped tungsten foils

Here we show that potassium-doped tungsten foil should be preferred to pure tungsten foil when considering tungsten laminate pipes for structural divertor applications. Potassium-doped tungsten materials are well known from the bulb industry and show an enhanced creep and recrystallization behaviour that can be explained by the formation of potassium-filled bubbles that are surrounding the elongated grains, leading to an interlocking of the microstructure. In this way, the ultra-fine grained (UFG) microstructure of tungsten foil can be stabilized and with it the extraordinary mechanical properties of the foil in terms of ductility, toughness, brittle-to-ductile transition, and radiation resistance. In this paper we show the results of three-point bending tests performed at room temperature on annealed pure tungsten and potassium-doped tungsten foils (800, 900, 1000, 1100, 1200, 1300, 1400, 1600, 1800, 2000, 2200, and 2400 °C for 1 h in vacuum). The microstructural assessment covers the measurement of the hardness and analyses of fractured surfaces as well as a comparison of the microstructure by optical microscopy. The results show that there is a positive effect of potassium-doped tungsten foils compared to pure tungsten foil and demonstrate the potential of the doped foil