Proposal of an Alternative Model for Speed-Flow Relationship in Two-Lane Highways

A research has been carried out in two-lanehighways in the Madrid Region to propose an alternativemodel for the speed-flowrelationship using regular loop data. The model is different in shape and, in some cases, slopes with respect to the contents of Highway Capacity Manual (HCM). A model is proposed for a mountainous area road, something for which the HCM does not provide explicitly a solution. The problem of a mountain road with high flows to access a popular recreational area is discussed, and some solutions are proposed. Up to 7 one-way sections of two-lanehighways have been selected, aiming at covering a significant number of different characteristics, to verify the proposed method the different classes of highways on which the Manual classifies them. In order to enunciate the model and to verify the basic variables of these types of roads a high number of data have been used. The counts were collected in the same way that the Madrid Region Highway Agency performs their counts. A total of 1.471 hours have been collected, in periods of 5 minutes. The models have been verified by means of specific statistical test (R2, T-Student, Durbin-Watson, ANOVA, etc.) and with the diagnostics of the contrast of assumptions (normality, linearity, homoscedasticity and independence). The model proposed for this type of highways with base conditions, can explain the different behaviors as traffic volumes increase, and follows a polynomial multiple regression model of order 3, S shaped. As secondary results of this research, the levels of service and the capacities of this road have been measured with the 2000 HCM methodology, and the results discussed. © 2011 Published by Elsevier Ltd.

Control by ATR-FTIR of surface treatment of cork stoppers and its effect on their mechanical performance

Fourier transform infrared (FTIR) spectroscopy was applied to determine the type of surface treatment and dose used on cork stoppers and to predict the friction between stopper and bottleneck. Agglomerated cork stoppers were finished with two different doses and using two surface treatments: P (paraffin and silicone), 15 and 25 mg/stopper, and S (only silicone), 10 and 15 mg/stopper. FTIR spectra were recorded at five points for each stopper by attenuated total reflectance (ATR). Absorbances at 1,010, 2,916, and 2,963 cm -1 were obtained in each spectrum. Discriminant analysis techniques allowed the treatment, and dose applied to each stopper to be identified from the absorbance values. 91.2% success rates were obtained from individual values and 96.0% from the mean values of each stopper. Spectrometric data also allowed treatment homogeneity to be determined on the stopper surface, and a multiple regression model was used to predict the friction index (If = Fe/Fc) (R 2 = 0.93)

Modelo del sistema de gestión de la calidad y el desempeño organizacional en la producción de petróleo

El proceso de cambio de una sociedad industrial a una sociedad del conocimiento, que experimenta el mundo globalizado en el siglo XXI, induce a las empresas y organizaciones a desarrollar ventajas competitivas y sostenibles basadas en sus activos intangibles, entre los cuales destacan los sistemas de gestión en general y los sistemas de gestión de la calidad (SGC) en particular. Las organizaciones dedicadas a la producción de petróleo están influenciadas por dicha tendencia. El petróleo es un recurso natural con reservas limitadas, cuya producción y consumo ha crecido progresivamente, aportando la mayor cuota (35 %) del total de la energía que se consume en el mundo contemporáneo, aporte que se mantendrá hasta el año 2035, según las previsiones más conservadoras. Por tanto, se hace necesario desarrollar modelos de producción innovadores, que contribuyan a la mejora del factor de recobro de los yacimientos y de la vida útil de los mismos, al tiempo que satisfagan los requerimientos de producción y consumo diarios de los exigentes mercados globales. El objeto de esta investigación es el desarrollo de un modelo de gestión de la calidad y su efecto en el desempeño organizacional, a través del efecto mediador de los constructos satisfacción del cliente interno y gestión del conocimiento en la producción de petróleo. Esta investigación de carácter explicativo, no experimental, transeccional y ex-postfacto, se realizó en la región petrolífera del lago de Maracaibo, al occidente de Venezuela, la cual tiene más de 70 años en producción y cuenta con yacimientos maduros. La población objeto de estudio fue de 369 trabajadores petroleros, quienes participaron en las mesas técnicas de la calidad, durante los meses de mayo y julio del año 2012, los cuales en su mayoría están en proceso de formación como analistas, asesores y auditores de los SGC. La técnica de muestreo aplicada fue de tipo aleatorio simple, con una muestra de 252 individuos. A la misma se le aplicó un cuestionario diseñado ad hoc, el cual fue validado por las técnicas de juicio de expertos y prueba piloto. El procedimiento de investigación se realizó a través de una secuencia, que incluyó la elaboración de un modelo teórico, basado en la revisión del estado del arte; un modelo factorial, sobre la base del análisis factorial de los datos de la encuesta; un modelo de regresión lineal, elaborado a través del método de regresión lineal simple y múltiple; un modelo de análisis de sendero, realizado con el software Amos 20 SPSS y finalmente, un modelo informático, realizado con el simulador Vensim PLE v.6.2. Los resultados obtenidos indican que el modelo teórico se transformó en un modelo empírico, en el cual, la variable independiente fue el SGC, la variable mediadora fue la integración de las dimensiones eliminación de la no conformidad, satisfacción del cliente interno y aprendizaje organizacional (ENCSCIAO) y la variable respuesta la integración de las dimensiones desempeño organizacional y aprendizaje organizacional (DOOA). Se verificó el efecto mediador del ENSCIAO sobre la relación SGC-DOOA con una bondad del ajuste, del 42,65%. En el modelo de regresión múltiple se encontró que las variables determinantes son eliminación de la no conformidad (ENC), conocimiento adquirido (CA) y conocimiento espontáneo (CE), lo cual fue corroborado con el modelo de análisis de sendero. El modelo informático se desarrolló empleando datos aproximados de una unidad de producción tipo, generándose cuatro escenarios; siendo el más favorable, aquel en el cual se aplicaba el SGC y variables relacionadas, reduciendo la desviación de la producción, incrementando el factor de recobro y ampliando la vida útil del yacimiento. Se concluye que la aplicación del SGC y constructos relacionados favorece el desempeño y la producción de las unidades de explotación de yacimientos petrolíferos maduros. Los principales aportes de la tesis son la obtención de un modelo de gestión de la producción de petróleo en yacimientos maduros, basado en los SGC. Asimismo, el desarrollo de un concepto de gestión de la calidad asociado a la reducción de la desviación de la producción petrolífera anual, al incremento del factor de recobro y al aumento de la vida útil del yacimiento. Las futuras líneas de investigación están orientadas a la aplicación del modelo en contextos reales y específicos, para medir su impacto y realizar los ajustes pertinentes. ABSTRACT The process of change from an industrial society to a knowledge-based society, which undergoes the globalized world in the twenty-first century, induces companies and organizations to develop a sustainable and competitive advantages based on its intangible assets, among which are noteworthy the management systems in general and particularly the quality management systems (QMS). Organizations engaged in oil production are influenced by said trend. Oil is a natural resource with limited reserves, where production and consumption has grown progressively, providing the largest share (35%) of the total energy consumed in the contemporary world, a contribution that will remain until the year 2035 according to the more conservative trust estimations. Therefore, it becomes necessary to develop innovative production models which contribute with the improvement of reservoirs´ recovery factor and the lifetime thereof, while meeting the production requirements and daily consumption of demanding global markets. The aim of this research is to develop a model of quality management and its effect on organizational performance through the mediator effect of the constructs, internal customer satisfaction and knowledge management in oil production. This research of explanatory nature, not experimental, transactional and expos-facto was carried out in the oil-region of Maracaibo Lake located to the west of Venezuela, which has more than 70 years in continuous production and has mature reservoirs. The population under study was 369 oil workers who participated in the technical quality workshops, during the months of May and July of 2012, the majority of which were in the process of training as analysts, consultants and auditors of the QMS. The sampling technique applied was simple random type. To a sample of 252 individuals of the population it was applied an ad hoc designed questionnaire, which was validated by the techniques of expert judgment and pilot test. The research procedure was performed through a sequence, which included the elaboration of a theoretical model, based on the review of the state of the art; a factorial model with based on factorial analysis of the survey data; a linear regression model, developed through the method of simple and multiple linear regression; a structural equation model, made with software °Amos 20 SPSS° and finally, a computer model, performed with the simulator Vensim PLE v.6.2. The results indicate that the theoretical model was transformed into an empirical model, in which the independent variable was the QMS, the mediator variable was the integration of the dimensions: elimination of non-conformity, internal customer satisfaction and organizational learning (ENCSCIAO) and the response variable the integration of the dimensions, organizational performance and learning organizational (DOOA). ENSCIAO´s mediator effect on the relation QMS-DOOA was verified with a goodness of fit of 42,65%. In the multiple regression model was found to be the determining variables are elimination of nonconformity (ENC), knowledge acquired (CA) and spontaneous knowledge (EC), which was verified with the structural equation model. The computer model was developed based on approximate data of an oil production unit type, creating four (04) scenarios; being the most favorable, that one which it was applied the QMS and related variables, reducing the production deviation, increasing the recovery factor and extending the lifetime of the reservoir. It is concluded that QMS implementation powered with the related constructs, favors performance and production of mature oilfield of exploitation reservoirs units. The main contributions of this thesis are obtaining a management model for oil production in mature oilfields, based on QMS. In addition, development of a concept of quality associated to reduce the annual oil production deviation, increase the recovery factor and increase oilfield lifetime. Future lines of research are oriented to the implementation of this model in real and specific contexts to measure its impact and make the necessary adjustments that might take place.

Una aproximación a la predicción del valor de acciones en la bolsa de valores aplicando técnicas de Data Mining

La predicción del valor de las acciones en la bolsa de valores ha sido un tema importante en el campo de inversiones, que por varios años ha atraído tanto a académicos como a inversionistas. Esto supone que la información disponible en el pasado de la compañía que cotiza en bolsa tiene alguna implicación en el futuro del valor de la misma. Este trabajo está enfocado en ayudar a un persona u organismo que decida invertir en la bolsa de valores a través de gestión de compra o venta de acciones de una compañía a tomar decisiones respecto al tiempo de comprar o vender basado en el conocimiento obtenido de los valores históricos de las acciones de una compañía en la bolsa de valores. Esta decisión será inferida a partir de un modelo de regresión múltiple que es una de las técnicas de datamining. Para llevar conseguir esto se emplea una metodología conocida como CRISP-DM aplicada a los datos históricos de la compañía con mayor valor actual del NASDAQ.---ABSTRACT---The prediction of the value of shares in the stock market has been a major issue in the field of investments, which for several years has attracted both academics and investors. This means that the information available in the company last traded have any involvement in the future of the value of it. This work is focused on helping an investor decides to invest in the stock market through management buy or sell shares of a company to make decisions with respect to time to buy or sell based on the knowledge gained from the historic values of the shares of a company in the stock market. This decision will be inferred from a multiple regression model which is one of the techniques of data mining. To get this out a methodology known as CRISP-DM applied to historical data of the company with the highest current value of NASDAQ is used.

Estimating the modal parameters from multiple measurement setups using a joint state space model

Computing the modal parameters of structural systems often requires processing data from multiple non-simultaneously recorded setups of sensors. These setups share some sensors in common, the so-called reference sensors, which are fixed for all measurements, while the other sensors change their position from one setup to the next. One possibility is to process the setups separately resulting in different modal parameter estimates for each setup. Then, the reference sensors are used to merge or glue the different parts of the mode shapes to obtain global mode shapes, while the natural frequencies and damping ratios are usually averaged. In this paper we present a new state space model that processes all setups at once. The result is that the global mode shapes are obtained automatically, and only a value for the natural frequency and damping ratio of each mode is estimated. We also investigate the estimation of this model using maximum likelihood and the Expectation Maximization algorithm, and apply this technique to simulated and measured data corresponding to different structures.

Multiple solutions and numerical analysis to the dynamic and stationary models coupling a delayed energy balance model involving latent heat and discontinuous albedo with a deep ocean

We study a climatologically important interaction of two of the main components of the geophysical system by adding an energy balance model for the averaged atmospheric temperature as dynamic boundary condition to a diagnostic ocean model having an additional spatial dimension. In this work, we give deeper insight than previous papers in the literature, mainly with respect to the 1990 pioneering model by Watts and Morantine. We are taking into consideration the latent heat for the two phase ocean as well as a possible delayed term. Non-uniqueness for the initial boundary value problem, uniqueness under a non-degeneracy condition and the existence of multiple stationary solutions are proved here. These multiplicity results suggest that an S-shaped bifurcation diagram should be expected to occur in this class of models generalizing previous energy balance models. The numerical method applied to the model is based on a finite volume scheme with nonlinear weighted essentially non-oscillatory reconstruction and Runge–Kutta total variation diminishing for time integration.

An Efficient Multiple Object Detection and Tracking Framework for Automatic Counting and Video Surveillance Applications

Automatic visual object counting and video surveillance have important applications for home and business environments, such as security and management of access points. However, in order to obtain a satisfactory performance these technologies need professional and expensive hardware, complex installations and setups, and the supervision of qualified workers. In this paper, an efficient visual detection and tracking framework is proposed for the tasks of object counting and surveillance, which meets the requirements of the consumer electronics: off-the-shelf equipment, easy installation and configuration, and unsupervised working conditions. This is accomplished by a novel Bayesian tracking model that can manage multimodal distributions without explicitly computing the association between tracked objects and detections. In addition, it is robust to erroneous, distorted and missing detections. The proposed algorithm is compared with a recent work, also focused on consumer electronics, proving its superior performance.

Two-layer particle filter for multiple target detection and tracking

This paper deals with the detection and tracking of an unknown number of targets using a Bayesian hierarchical model with target labels. To approximate the posterior probability density function, we develop a two-layer particle filter. One deals with track initiation, and the other with track maintenance. In addition, the parallel partition method is proposed to sample the states of the surviving targets.

Energy/power consumption model for an embedded processor board

This dissertation, whose research has been conducted at the Group of Electronic and Microelectronic Design (GDEM) within the framework of the project Power Consumption Control in Multimedia Terminals (PCCMUTE), focuses on the development of an energy estimation model for the battery-powered embedded processor board. The main objectives and contributions of the work are summarized as follows: A model is proposed to obtain the accurate energy estimation results based on the linear correlation between the performance monitoring counters (PMCs) and energy consumption. the uniqueness of the appropriate PMCs for each different system, the modeling methodology is improved to obtain stable accuracies with slight variations among multiple scenarios and to be repeatable in other systems. It includes two steps: the former, the PMC-filter, to identify the most proper set among the available PMCs of a system and the latter, the k-fold cross validation method, to avoid the bias during the model training stage. The methodology is implemented on a commercial embedded board running the 2.6.34 Linux kernel and the PAPI, a cross-platform interface to configure and access PMCs. The results show that the methodology is able to keep a good stability in different scenarios and provide robust estimation results with the average relative error being less than 5%. Este trabajo fin de máster, cuya investigación se ha desarrollado en el Grupo de Diseño Electrónico y Microelectrónico (GDEM) en el marco del proyecto PccMuTe, se centra en el desarrollo de un modelo de estimación de energía para un sistema empotrado alimentado por batería. Los objetivos principales y las contribuciones de esta tesis se resumen como sigue: Se propone un modelo para obtener estimaciones precisas del consumo de energía de un sistema empotrado. El modelo se basa en la correlación lineal entre los valores de los contadores de prestaciones y el consumo de energía. Considerando la particularidad de los contadores de prestaciones en cada sistema, la metodología de modelado se ha mejorado para obtener precisiones estables, con ligeras variaciones entre escenarios múltiples y para replicar los resultados en diferentes sistemas. La metodología incluye dos etapas: la primera, filtrado-PMC, que consiste en identificar el conjunto más apropiado de contadores de prestaciones de entre los disponibles en un sistema y la segunda, el método de validación cruzada de K iteraciones, cuyo fin es evitar los sesgos durante la fase de entrenamiento. La metodología se implementa en un sistema empotrado que ejecuta el kernel 2.6.34 de Linux y PAPI, un interfaz multiplataforma para configurar y acceder a los contadores. Los resultados muestran que esta metodología consigue una buena estabilidad en diferentes escenarios y proporciona unos resultados robustos de estimación con un error medio relativo inferior al 5%.

Molecular basis of salt tolerance in Physcomitrella Patens model plant: potassium homeostasis and physiological roles of chx transporters

El suelo salino impone un estrés abiótico importante que causa graves problemas en la agricultura ya que la mayoría de los cultivos se ven afectados por la salinidad debido a efectos osmóticos y tóxicos. Por ello, la contaminación y la escasez de agua dulce, la salinización progresiva de tierras y el aumento exponencial de la población humana representan un grave problema que amenaza la seguridad alimentaria mundial para las generaciones futuras. Por lo tanto, aumentar la tolerancia a la salinidad de los cultivos es un objetivo estratégico e ineludible para garantizar el suministro de alimentos en el futuro. Mantener una óptima homeostasis de K+ en plantas que sufren estrés salino es un objetivo importante en el proceso de obtención de plantas tolerantes a la salinidad. Aunque el modelo de la homeostasis de K+ en las plantas está razonablemente bien descrito en términos de entrada de K+, muy poco se sabe acerca de los genes implicados en la salida de K+ o de su liberación desde la vacuola. En este trabajo se pretende aclarar algunos de los mecanismos implicados en la homeostasis de K+ en plantas. Para ello se eligió la briofita Physcomitrella patens, una planta no vascular de estructura simple y de fase haploide dominante que, entre muchas otras cualidades, hacen que sea un modelo ideal. Lo más importante es que no sólo P. patens es muy tolerante a altas concentraciones de Na+, sino que también su posición filogenética en la evolución de las plantas abre la posibilidad de estudiar los cambios claves que, durante el curso de la evolución, se produjeron en las diversas familias de los transportadores de K+. Se han propuesto varios transportadores de cationes como candidatos que podrían tener un papel en la salida de K+ o su liberación desde la vacuola, especialmente miembros de la familia CPA2 que contienen las familias de transportadores KEA y CHX. En este estudio se intenta aumentar nuestra comprensión de las funciones de los transportadores de CHX en las células de las plantas usando P. patens, como ya se ha dicho. En esta especie, se han identificado cuatro genes CHX, PpCHX1-4. Dos de estos genes, PpCHX1 y PpCHX2, se expresan aproximadamente al mismo nivel que el gen PpACT5, y los otros dos genes muestran una expresión muy baja. La expresión de PpCHX1 y PpCHX2 en mutantes de Escherichia coli defectivos en el transporte de K+ restauraron el crecimiento de esta cepa en medios con bajo contenido de K+, lo que viii sugiere que la entrada de K+ es energizada por un mecanismo de simporte con H+. Por otra parte, estos transportadores suprimieron el defecto asociado a la mutación kha1 en Saccharomyces cerevisiae, lo que sugiere que podrían mediar un antiporte en K+/H+. La proteína PpCHX1-GFP expresada transitoriamente en protoplastos de P. patens co-localizó con un marcador de Golgi. En experimentos similares, la proteína PpCHX2-GFP localizó aparentemente en la membrana plasmática y tonoplasto. Se construyeron las líneas mutantes simples de P. patens ΔPpchx1 y ΔPpchx2, y también el mutante doble ΔPpchx2 ΔPphak1. Los mutantes simples crecieron normalmente en todas las condiciones ensayadas y mostraron flujos de entrada normales de K+ y Rb+; la mutación ΔPpchx2 no aumentó el defecto de las plantas ΔPphak1. En experimentos a largo plazo, las plantas ΔPpchx2 mostraron una retención de Rb+ ligeramente superior que las plantas silvestres, lo que sugiere que PpCHX2 promueve la transferencia de Rb+ desde la vacuola al citosol o desde el citosol al medio externo, actuando en paralelo con otros transportadores. Sugerimos que transportadores de K+ de varias familias están involucrados en la homeostasis de pH de orgánulos ya sea mediante antiporte K+/H+ o simporte K+-H+.ix ABSTRACT Soil salinity is a major abiotic stress causing serious problems in agriculture as most crops are affected by it. Moreover, the contamination and shortage of freshwater, progressive land salinization and exponential increase of human population aggravates the problem implying that world food security may not be ensured for the next generations. Thus, a strategic and an unavoidable goal would be increasing salinity tolerance of plant crops to secure future food supply. Maintaining an optimum K+ homeostasis in plants under salinity stress is an important trait to pursue in the process of engineering salt tolerant plants. Although the model of K+ homeostasis in plants is reasonably well described in terms of K+ influx, very little is known about the genes implicated in K+ efflux or release from the vacuole. In this work, we aim to clarify some of the mechanisms involved in K+ homeostasis in plants. For this purpose, we chose the bryophyte plant Physcomitrella patens, a nonvascular plant of simple structure and dominant haploid phase that, among many other characteristics, makes it an ideal model. Most importantly, not only P. patens is very tolerant to high concentrations of Na+, but also its phylogenetic position in land plant evolution opens the possibility to study the key changes that occurred in K+ transporter families during the course of evolution. Several cation transporter candidates have been proposed to have a role in K+ efflux or release from the vacuole especially members of the CPA2 family which contains the KEA and CHX transporter families. We intended in this study to increase our understanding of the functions of CHX transporters in plant cells using P. patens, in which four CHX genes have been identified, PpCHX1-4. Two of these genes, PpCHX1 and PpCHX2, are expressed at approximately the same level as the PpACT5 gene, but the other two genes show an extremely low expression. PpCHX1 and PpCHX2 restored growth of Escherichia coli mutants on low K+-containing media, suggesting they mediated K+ uptake that may be energized by symport with H+. In contrast, these genes suppressed the defect associated to the kha1 mutation in Saccharomyces cerevisiae, which suggest that they might mediate K+/H+ antiport. PpCHX1-GFP protein transiently expressed in P. patens protoplasts co-localized with a Golgi marker. In similar experiments, the PpCHX2-GFP protein appeared to localize to tonoplast and plasma x membrane. We constructed the ΔPpchx1 and ΔPpchx2 single mutant lines, and the ΔPpchx2 ΔPphak1 double mutant. Single mutant plants grew normally under all the conditions tested and exhibited normal K+ and Rb+ influxes; the ΔPpchx2 mutation did not increase the defect of ΔPphak1 plants. In long-term experiments, ΔPpchx2 plants showed a slightly higher Rb+ retention than wild type plants, which suggests that PpCHX2 mediates the transfer of Rb+ from either the vacuole to the cytosol or from the cytosol to the external medium in parallel with other transporters. We suggest that K+ transporters of several families are involved in the pH homeostasis of organelles by mediating either K+/H+ antiport or K+-H+ symport.

A model for integrating learning object repository resources into web videoconference services

Reusing Learning Objects saves time and reduce development costs. Hence, achieving their interoperability in multiple contexts is essential when creating a Learning Object Repository. On the other hand, novel web videoconference services are available due to technological advancements. Several benefits can be gained by integrating Learning Objects into these services. For instance, they can allow sharing, co-viewing and synchronized co-browsing of these resources at the same time that provide real time communication. However, several efforts need to be undertaken to achieve the interoperability with these systems. In this paper, we propose a model to integrate the resources of the Learning Object Repositories into web videoconference services. The experience of applying this model in a real e-Learning scenario achieving interoperability with two different web videoconference services is also described.

Massively parallelizable list-mode reconstruction using a Monte Carlo-based elliptical Gaussian model

Purpose: A fully three-dimensional (3D) massively parallelizable list-mode ordered-subsets expectation-maximization (LM-OSEM) reconstruction algorithm has been developed for high-resolution PET cameras. System response probabilities are calculated online from a set of parameters derived from Monte Carlo simulations. The shape of a system response for a given line of response (LOR) has been shown to be asymmetrical around the LOR. This work has been focused on the development of efficient region-search techniques to sample the system response probabilities, which are suitable for asymmetric kernel models, including elliptical Gaussian models that allow for high accuracy and high parallelization efficiency. The novel region-search scheme using variable kernel models is applied in the proposed PET reconstruction algorithm. Methods: A novel region-search technique has been used to sample the probability density function in correspondence with a small dynamic subset of the field of view that constitutes the region of response (ROR). The ROR is identified around the LOR by searching for any voxel within a dynamically calculated contour. The contour condition is currently defined as a fixed threshold over the posterior probability, and arbitrary kernel models can be applied using a numerical approach. The processing of the LORs is distributed in batches among the available computing devices, then, individual LORs are processed within different processing units. In this way, both multicore and multiple many-core processing units can be efficiently exploited. Tests have been conducted with probability models that take into account the noncolinearity, positron range, and crystal penetration effects, that produced tubes of response with varying elliptical sections whose axes were a function of the crystal's thickness and angle of incidence of the given LOR. The algorithm treats the probability model as a 3D scalar field defined within a reference system aligned with the ideal LOR. Results: This new technique provides superior image quality in terms of signal-to-noise ratio as compared with the histogram-mode method based on precomputed system matrices available for a commercial small animal scanner. Reconstruction times can be kept low with the use of multicore, many-core architectures, including multiple graphic processing units. Conclusions: A highly parallelizable LM reconstruction method has been proposed based on Monte Carlo simulations and new parallelization techniques aimed at improving the reconstruction speed and the image signal-to-noise of a given OSEM algorithm. The method has been validated using simulated and real phantoms. A special advantage of the new method is the possibility of defining dynamically the cut-off threshold over the calculated probabilities thus allowing for a direct control on the trade-off between speed and quality during the reconstruction.

Joint statistical analysis of multiple measurement setups for the estimation of vibrational modes

Computing the modal parameters of large structures in Operational Modal Analysis often requires to process data from multiple non simultaneously recorded setups of sensors. These setups share some sensors in common, the so-called reference sensors that are fixed for all the measurements, while the other sensors are moved from one setup to the next. One possibility is to process the setups separately what result in different modal parameter estimates for each setup. Then the reference sensors are used to merge or glue the different parts of the mode shapes to obtain global modes, while the natural frequencies and damping ratios are usually averaged. In this paper we present a state space model that can be used to process all setups at once so the global mode shapes are obtained automatically and subsequently only a value for the natural frequency and damping ratio of each mode is computed. We also present how this model can be estimated using maximum likelihood and the Expectation Maximization algorithm. We apply this technique to real data measured at a footbridge.

Toward a planning model for the peruvian university system as a competitive strategy.

University education in Peru is based on models of teacher-centered teaching and a conception of knowledge which is closed and static and under the dominance of an information model now overwhelmed by multiple factors hastened by international change. The worlds most prestigious universities have chosen cultural diversity as a sign of quality and are hence interested in the mobility of teachers and students through exchange and cooperation with foreign educational institutions. These universities respond more effectively to pressure from the international business sector, better satisfy training demands, introduce new information and communication technologies into education and research and have improved administration and management structures. While there is progress, the university system in Peru is a planning model defined "as a discipline that seeks to respond to the needs of an organization defined by new cultural and social models" (A. Cazorla, et al 2007).This paper studies the non-Euclidean thinking of planning and development of John Friedmann (2001). Based on the four domains of social practice, it proposes a planning model for Peruvian universities that meets international requirements.

A general framework to testing the effect of transport policy measures to achieve a modal shift: a sequental hybrid model

In order to achieve to minimize car-based trips, transport planners have been particularly interested in understanding the factors that explain modal choices. In the transport modelling literature there has been an increasing awareness that socioeconomic attributes and quantitative variables are not sufficient to characterize travelers and forecast their travel behavior. Recent studies have also recognized that users? social interactions and land use patterns influence travel behavior, especially when changes to transport systems are introduced, but links between international and Spanish perspectives are rarely deal. In this paper, factorial and path analyses through a Multiple-Indicator Multiple-Cause (MIMIC) model are used to understand and describe the relationship between the different psychological and environmental constructs with social influence and socioeconomic variables. The MIMIC model generates Latent Variables (LVs) to be incorporated sequentially into Discrete Choice Models (DCM) where the levels of service and cost attributes of travel modes are also included directly to measure the effect of the transport policies that have been introduced in Madrid during the last three years in the context of the economic crisis. The data used for this paper are collected from a two panel smartphone-based survey (n=255 and 190 respondents, respectively) of Madrid.