Risk of nitrate pollution in agricultural systems

Se propone una metodología que nos permita evaluar un óptimo manejo de la fertirrigación integrando aspectos agronómicos y medioambientales.

Methodology to assess economic and environmental impacts of nitrogen in fertirrigation systems.

To determine the risk of nitrate pollution in agricultural systems have identified several indexes and efficiencies that may lead an effective N fertilizer management for obtain the maximum yield with minimum environmental impact and health

Design methodology in multiphase buck converter based on minimum time control for high efficiency RF amplifiers

This paper proposes an interleaved multiphase buck converter with minimum time control strategy for envelope amplifiers in high efficiency RF power amplifiers. The solution of the envelope amplifier is to combine the proposed converter with a linear regulator in series. High system efficiency can be obtained through modulating the supply voltage of the envelope amplifier with the fast output voltage variation of the converter working with several particular duty cycles that achieve total ripple cancellation. The transient model for minimum time control is explained, and the calculation of transient times that are pre-calculated and inserted into a look-up table is presented. The filter design trade-off that limits capability of envelope modulation is also discussed. The experimental results verify the fast voltage transient obtained with a 4-phase buck prototype.

Design of envelope amplifier based on interleaved multiphase buck converter with minimum time control for RF application

In this paper, an interleaved multiphase buck converter with minimum time control strategy for envelope amplifiers in high efficiency RF power amplifiers is proposed. The solution for the envelope amplifier is to combine the proposed converter with a linear regulator in series. High efficiency of envelope amplifier can be obtained through modulating the supply voltage of the linear regulator. Instead of tracking the envelope, the buck converter has discrete output voltage that corresponding to particular duty cycles which achieve total ripple cancellation. The transient model for minimum time control is explained, and the calculation of transient times that are pre-calculated and inserted into a lookup table is presented. The filter design trade-off that limits capability of envelope modulation is also discussed. The experimental results verify the fast voltage transient obtained with a 4-phase buck prototype.

Multiphase Buck Converter with Minimum Time Control Strategy for RF Envelope Modulation

Power amplifier supplied with constant supply voltage has very low efficiency in the transmitter. A DC-DC converter in series with a linear regulator can be used to obtain voltage modulation. Since this converter should be able to change the output voltage very fast, a multiphase buck converter with a minimum time control strategy is proposed. To modulate supply voltage of the envelope amplifier, the multiphase converter works with some particular duty cycle (i/n, i=1, 2 ... n, n is the number of phase) to generate discrete output voltages, and in these duty cycles the output current ripple can be completely cancelled. The transition times for the minimum time are pre-calculated and inserted in a look-up table. The theoretical background, the system model that is necessary in order to calculate the transition times and the experimental results obtained with a 4-phase buck prototype are given

Estudio sobre la influencia de la inoculación de las rizobacterias Azospirillum brasilense y Pseudomonas fluorescens sobre el desarrollo morfológico y el contenido de aceites esenciales en las especies aromáticas Ocimum basilicum var. genovesse, Ocimum basilicum var. minimum, Petroselinum sativum var. lisa y Salvia officinalis.

En el presente estudio se analiza la influencia de la inoculación con Azospirillum brasilense, con Pseudomonas fluorescens y la inoculación conjunta con ambas rizobacterias en las especies de plantas aromáticas Ocimum basilicum var. genovesse, Ocimum basilicum var. minimum, Petroselinum sativum var. lisa y Salvia officinalis. Se evaluará su desarrollo morfológico, atendiendo a tres parámetros: la longitud del tallo, el peso fresco y la superficie foliar. Así como el posible incremento en el contenido de aceite esencial que pueda tener la planta tratada. El cultivo se llevó a cabo en alveolos de ForestPot® 300, sobre mezcla de turba y vermiculita 3:1, con riego diario y sin adición de fertilizantes. Los resultados indican que en todas las especies y en todos los apartados estudiados, la inoculación de las rizobacterias produjo un incremento del desarrollo y del contenido de aceite esencial en comparación con el tratamiento Control, excepto en el caso de la longitud de las dos variedades de O. basilicum al inocularlas con P. fluorescens, en las que produjo una ligera disminución respecto al Control. En el caso de P. sativum var. lisa, solo las plantas que fueron inoculadas sobrevivieron. A partir de estos resultados, puede decirse que la inoculación con estas rizobacteras promotoras del crecimiento puede tener una gran importancia como sustitución de fertilizantes minerales, obteniéndose de este modo una producción más ecológica y respetuosa con el medio.

Unsupervised system to classify SO2 pollutant concentrations in Salamanca, Mexico

Salamanca is cataloged as one of the most polluted cities in Mexico. In order to observe the behavior and clarify the influence of wind parameters on the Sulphur Dioxide (SO2) concentrations a Self-Organizing Maps (SOM) Neural Network have been implemented at three monitoring locations for the period from January 1 to December 31, 2006. The maximum and minimum daily values of SO2 concentrations measured during the year of 2006 were correlated with the wind parameters of the same period. The main advantages of the SOM Neural Network is that it allows to integrate data from different sensors and provide readily interpretation results. Especially, it is powerful mapping and classification tool, which others information in an easier way and facilitates the task of establishing an order of priority between the distinguished groups of concentrations depending on their need for further research or remediation actions in subsequent management steps. For each monitoring location, SOM classifications were evaluated with respect to pollution levels established by Health Authorities. The classification system can help to establish a better air quality monitoring methodology that is essential for assessing the effectiveness of imposed pollution controls, strategies, and facilitate the pollutants reduction.

The Minimum Number of Points Taking Part in k-Sets in Sets of Unaligned Points

En este trabajo se da un ejemplo de un conjunto de n puntos situados en posición general, en el que se alcanza el mínimo número de puntos que pueden formar parte de algún k-set para todo k con 1menor que=kmenor quen/2. Se generaliza también, a puntos en posición no general, el resultado de Erdõs et al., 1973, sobre el mínimo número de puntos que pueden formar parte de algún k-set. The study of k- sets is a very relevant topic in the research area of computational geometry. The study of the maximum and minimum number of k-sets in sets of points of the plane in general position, specifically, has been developed at great length in the literature. With respect to the maximum number of k-sets, lower bounds for this maximum have been provided by Erdõs et al., Edelsbrunner and Welzl, and later by Toth. Dey also stated an upper bound for this maximum number of k-sets. With respect to the minimum number of k-set, this has been stated by Erdos el al. and, independently, by Lovasz et al. In this paper the authors give an example of a set of n points in the plane in general position (no three collinear), in which the minimum number of points that can take part in, at least, a k-set is attained for every k with 1 ≤ k < n/2. The authors also extend Erdos’s result about the minimum number of points in general position which can take part in a k-set to a set of n points not necessarily in general position. That is why this work complements the classic works we have mentioned before.

Recuperación de energía de la salmuera

Como consecuencia del proceso de desalación, se produce el vertido al mar de un agua de rechazo hipersalino o salmuera. La salinidad de este vertido es variable, dependiendo del origen de la captación y del proceso de tratamiento. Muchos de los hábitats y biocenosis de los ecosistemas marinos se encuentran adaptados a ambientes de salinidad casi constante y son muy susceptibles a los incrementos de salinidad originados por estos vertidos. Junto con el vertido de salmuera otro de los principales inconvenientes que plantean las plantas desaladoras es el alto consumo energético, con todas las desventajas que esto supone: alto coste del agua desalada para los consumidores, contaminación del medio... El desarrollo de los métodos de vertido, herramientas de gestión de la salmuera, estudios del comportamiento de la pluma salina… ha buscado la mitigación de estos efectos sobre los ecosistemas marinos. El desarrollo en membranas de ósmosis inversa, diseño de bombas y sistemas de recuperación de energía ha permitido también la reducción del consumo energético en las plantas de desalación. Sin embargo, estos campos parecen haber encontrado un techo tecnológico difícil de rebasar en los últimos tiempos. La energía osmótica se plantea como uno de los caminos a investigar aplicado al campo de la reducción del consumo energético en desalación de agua de mar, a través del aprovechamiento energético de la salmuera. Con esta tesis se pretende cumplir principalmente con los siguientes objetivos: reducción del consumo energético en desalación, mitigar el impacto del vertido sobre el medio y ser una nueva herramienta en la gestión de la salmuera. En el presente documento se plantea el desarrollo de un nuevo proceso que utiliza el fenómeno de la ósmosis directa a través de membranas semipermeables, y busca la sinergia desalación depuración, integrando ambos, en un único proceso de tratamiento dentro del ciclo integral del agua. Para verificar los valores de producción, calidad y rendimiento del proceso, se proyecta y construye una planta piloto ubicada en la Planta Desaladora de Alicante II, escalada de tal manera que permite la realización de los ensayos con equipos comerciales de tamaño mínimo. El objetivo es que el resultado final sea extrapolable a tamaños superiores sin que el escalado afecte a la certeza y fiabilidad de las conclusiones obtenidas. La planta se proyecta de forma que el vertido de una desaladora de ósmosis inversa junto con el vertido de un terciario convencional, se pasan por una ósmosis directa y a continuación por una ósmosis inversa otra vez, ésta última con el objeto de abrir la posibilidad de incrementar la producción de agua potable. Ambas ósmosis están provistas de un sistema de pretratamiento físico-químico (para adecuar la calidad del agua de entrada a las condiciones requeridas por las membranas en ambos casos), y un sistema de limpieza química. En todos los ensayos se usa como fuente de disolución concentrada (agua salada), el rechazo de un bastidor de ósmosis inversa de una desaladora convencional de agua de mar. La fuente de agua dulce marca la distinción entre dos tipos de ensayos: ensayos con el efluente del tratamiento terciario de una depuradora convencional, con lo que se estudia el comportamiento de la membrana ante el ensuciamiento; y ensayos con agua permeada, que permiten estudiar el comportamiento ideal de la membrana. Los resultados de los ensayos con agua salobre ponen de manifiesto problemas de ensuciamiento de la membrana, el caudal de paso a través de la misma disminuye con el tiempo y este efecto se ve incrementado con el aumento de la temperatura del agua. Este fenómeno deriva en una modificación del pretratamiento de la ósmosis directa añadiendo un sistema de ultrafiltración que ha permitido que la membrana presente un comportamiento estable en el tiempo. Los ensayos con agua permeada han hecho posible estudiar el comportamiento “ideal” de la membrana y se han obtenido las condiciones óptimas de operación y a las que se debe tender, consiguiendo tasas de recuperación de energía de 1,6; lo que supone pasar de un consumo de 2,44 kWh/m3 de un tren convencional de ósmosis a 2,28 kWh/m3 al añadir un sistema de ósmosis directa. El objetivo de futuras investigaciones es llegar a tasas de recuperación de 1,9, lo que supondría alcanzar consumos inferiores a 2 kWh/m3. Con esta tesis se concluye que el proceso propuesto permite dar un paso más en la reducción del consumo energético en desalación, además de mitigar los efectos del vertido de salmuera en el medio marino puesto que se reduce tanto el caudal como la salinidad del vertido, siendo además aplicable a plantas ya existentes y planteando importantes ventajas económicas a plantas nuevas, concebidas con este diseño. As a consequence of the desalination process, a discharge of a hypersaline water or brine in the sea is produced. The salinity of these discharges varies, depending on the type of intake and the treatment process. Many of the habitats and biocenosis of marine ecosystems are adapted to an almost constant salinity environment and they are very susceptible to salinity increases caused by these discharges. Besides the brine discharge, another problem posed by desalination plants, is the high energy consumption, with all the disadvantages that this involves: high cost of desalinated water for consumers, environmental pollution ... The development of methods of disposal, brine management tools, studies of saline plume ... has sought the mitigation of these effects on marine ecosystems. The development of reverse osmosis membranes, pump design and energy recovery systems have also enabled the reduction of energy consumption in desalination plants. However, these fields seem to have reached a technological ceiling which is difficult to exceed in recent times. Osmotic power is proposed as a new way to achieve the reduction of energy consumption in seawater desalination, through the energy recovery from the brine. This thesis mainly tries to achieve the following objectives: reduction of energy consumption in desalination, mitigation of the brine discharge impact on the environment and become a new tool in the management of the brine. This paper proposes the development of a new process, that uses the phenomenon of forward osmosis through semipermeable membranes and seeks the synergy desalination-wastewater reuse, combining both into a single treatment process within the integral water cycle. To verify the production, quality and performance of the process we have created a pilot plant. This pilot plant, located in Alicante II desalination plant, has been designed and built in a scale that allows to carry out the tests with minimum size commercial equipment. The aim is that the results can be extrapolated to larger sizes, preventing that the scale affects the accuracy and reliability of the results. In the projected plant, the discharge of a reverse osmosis desalination plant and the effluent of a convencional tertiary treatment of a wastewater plant, go through a forward osmosis module, and then through a reverse osmosis, in order to open the possibility of increasing potable water production. Both osmosis systems are provided with a physicochemical pretreatment (in order to obtain the required conditions for the membranes in both cases), and a chemical cleaning system. In all tests, it is used as a source of concentrated solution (salt water), the rejection of a rack of a conventional reverse osmosis seawater desalination. The source of fresh water makes the difference between two types of tests: test with the effluent from a tertiary treatment of a conventional wastewater treatment plant (these tests study the behavior of the membrane facing the fouling) and tests with permeate, which allow us to study the ideal behavior of the membrane. The results of the tests with brackish water show fouling problems, the flow rate through the membrane decreases with the time and this effect is increased with water temperature. This phenomenon causes the need for a modification of the pretreatment of the direct osmosis module. An ultrafiltration system is added to enable the membrane to present a stable behavior . The tests with permeate have made possible the study of the ideal behavior of the membrane and we have obtained the optimum operating conditions. We have achieved energy recovery rates of 1.6, which allows to move from a consumption of 2.44 kWh/m3 in a conventional train of reverse osmosis to 2.28 kWh / m3 if it is added the direct osmosis system. The goal of future researches is to achieve recovery rates of 1.9, which would allow to reach a consumption lower than 2 kWh/m3. This thesis concludes that the proposed process allows us to take a further step in the reduction of the energy consumption in desalination. We must also add the mitigation of the brine discharge effects on the marine environment, due to the reduction of the flow and salinity of the discharge. This is also applicable to existing plants, and it suggests important economic benefits to new plants that will be built with this design.

Use of calculus of variations to determine the shape of hovering rotors of minimum power and its application to micro air vehicles

In this paper, calculus of variations and combined blade element and momentum theory (BEMT) are used to demonstrate that, in hover, when neither root nor tip losses are considered; the rotor, which minimizes the total power (MPR), generates an induced velocity that varies linearly along the blade span. The angle of attack of every blade element is constant and equal to its optimum value. The traditional ideal twist (ITR) and optimum (OR) rotors are revisited in the context of this variational framework. Two more optimum rotors are obtained considering root and tip losses, the ORL, and the MPRL. A comparison between these five rotors is presented and discussed. The MPR and MPRL present a remarkable saving of power for low values of both thrust coefficient and maximum aerodynamic efficiency. The result obtained can be exploited to improve the aerodynamic behaviour of rotary wing micro air vehicles (MAV). A comparison with experimental results obtained from the literature is presented.

Levels, sources and seasonality of coarse particles (PM10-PM2.5) in three European capitals e implications for particulate pollution control

Coarse particles of aerodynamic diameter between 2.5 and 10 mm (PMc) are produced by a range of natural (windblown dust and sea sprays) and anthropogenic processes (non-exhaust vehicle emissions, industrial, agriculture, construction and quarrying activities). Although current ambient air quality regulations focus on PM2.5 and PM10, coarse particles are of interest from a public health point of view as they have been associated with certain mortality and morbidity outcomes. In this paper, an analysis of coarse particle levels in three European capitals (London, Madrid and Athens) is presented and discussed. For all three cities we analysed data from both traffic and urban background monitoring sites. The results showed that the levels of coarse particles present significant seasonal, weekly and daily variability. Their wind driven and non-wind driven resuspension as well as their roadside increment due to traffic were estimated. Both the local meteorological conditions and the air mass history indicating long-range atmospheric transport of particles of natural origin are significant parameters that influence the levels of coarse particles in the three cities especially during episodic events.

Solving the minimum vertex floodlight problem with hybrid metaheuristics

In this paper we propose four approximation algorithms (metaheuristic based), for the Minimum Vertex Floodlight Set problem. Urrutia et al. [9] solved the combinatorial problem, although it is strongly believed that the algorithmic problem is NP-hard. We conclude that, on average, the minimum number of vertex floodlights needed to illuminate a orthogonal polygon with n vertices is n/4,29.

Approaching minimum area polygonization

The problem of finding a minimum area polygonization for a given set of points in the plane, Minimum Area Polygonization (MAP) is NP-hard. Due to the complexity of the problem we aim at the development of algorithms to obtain approximate solutions. In this work, we suggest di?erent strategies in order to minimize the polygonization area.We propose algorithms to search for approximate solutions for MAP problem. We present an experimental study for a set of instances for MAP problem.

Approximations on minimum weight pseudo-triangulation problem using ant colony optimization

In this work, we consider the Minimum Weight Pseudo-Triangulation (MWPT) problem of a given set of n points in the plane. Globally optimal pseudo-triangulations with respect to the weight, as optimization criteria, are difficult to be found by deterministic methods, since no polynomial algorithm is known. We show how the Ant Colony Optimization (ACO) metaheuristic can be used to find high quality pseudo-triangulations of minimum weight. We present the experimental and statistical study based on our own set of instances since no reference to benchmarks for these problems were found in the literature. Throughout the experimental evaluation, we appraise the ACO metaheuristic performance for MWPT problem.

Air pollution data classification by SOM Neural Network

Over the last ten years, Salamanca has been considered among the most polluted cities in México. This paper presents a Self-Organizing Maps (SOM) Neural Network application to classify pollution data and automatize the air pollution level determination for Sulphur Dioxide (SO2) in Salamanca. Meteorological parameters are well known to be important factors contributing to air quality estimation and prediction. In order to observe the behavior and clarify the influence of wind parameters on the SO2 concentrations a SOM Neural Network have been implemented along a year. The main advantages of the SOM is that it allows to integrate data from different sensors and provide readily interpretation results. Especially, it is powerful mapping and classification tool, which others information in an easier way and facilitates the task of establishing an order of priority between the distinguished groups of concentrations depending on their need for further research or remediation actions in subsequent management steps. The results show a significative correlation between pollutant concentrations and some environmental variables.