Dynamic analysis using finite elements to calculate the critical wear section of the contact wire in suburban railway overhead conductor rails

The purpose of this study is to determine the critical wear levels of the contact wire of the catenary on metropolitan lines. The study has focussed on the zones of contact wire where localised wear is produced, normally associated with the appearance of electric arcs. To this end, a finite element model has been developed to study the dynamics of pantograph-catenary interaction. The model includes a zone of localised wear and a singularity in the contact wire in order to simulate the worst case scenario from the point of view of stresses. In order to consider the different stages in the wire wear process, different depths and widths of the localised wear zone were defined. The results of the dynamic simulations performed for each stage of wear let the area of the minimum resistant section of the contact wire be determined for which stresses are greater than the allowable stress. The maximum tensile stress reached in the contact wire shows a clear sensitivity to the size of the local wear zone, defined by its width and depth. In this way, if the wear measurements taken with an overhead line recording vehicle are analysed, it will be possible to calculate the potential breakage risk of the wire. A strong dependence of the tensile forces of the contact wire has also been observed. These results will allow priorities to be set for replacing the most critical sections of wire, thereby making maintenance much more efficient. The results obtained show that the wire replacement criteria currently borne in mind have turned out to be appropriate, although in some wear scenarios these criteria could be adjusted even more, and so prolong the life cycle of the contact wire.

Safety assessment of underground vehicles passing over highly resilient straight tracks in the presence of a broken rail

In this paper, vehicle-track interaction for a new slab track design, conceived to reduce noise and vibration levels has been analyzed, assessing the derailment risk for trains running on curved track when encountering a broken rail. Two different types of rail fastening systems with different elasticities have been analysed and compared. Numerical methods were used in order to simulate the dynamic behaviour of the train-track interaction. Multibody system (MBS) modelling techniques were combined with techniques based on the finite element method (FEM). MBS modelling was used for modelling the vehicle and FEM for simulating the elastic track. The simulation model was validated by comparing simulated results to experimental data obtained in field testing. During the simulations various safety indices, characteristic of derailment risk, were analysed. The simulations realised at the maximum running velocity of 110 km/h showed a similar behaviour for several track types. When reducing the running speed, the safety indices worsened for both cases. Although the worst behaviour was observed for the track with a greater elasticity, in none of the simulations did a derailment occur when running over the broken rail.

Effectiveness of resilient wheels in reducing noise and vibrations

This study focuses on the effectiveness of resilient wheels in reducing railway noise and vibrations, and compares the effectiveness of three types of wheels. The finite elements method has been used to characterise the vibratory behaviour of these wheels. The model has been excited with a realistic spectrum of vertical track irregularities, and a spectral analysis has been carried out. Results have been post-processed in order to estimate the sound power emitted. These calculations have been used to assess the effectiveness of the resilient wheel designs in reducing noise emitted to the environment and in propagating structural vibrations.

Metro de Madrid rolling stock models and comparative studies relating to comfort

This paper presents the work carried out by Metro de Madrid and the Railway Technology Research Centre (Polytechnic University of Madrid), aimed at setting up rolling stock simulation models with a high level of detail. To do this, the features of the SIMPACK simulation tool used to create models have been briefly outlined, explaining the main features of models in two of the series modelled: 7000 and 8000. Finally, the results obtained from comparing comfort in the 7000 and 8000 series are presented.

Atlas visual de cincuenta y siete años de arquitectura

En 1929 aparece el primer número de AA (L’architecture d’aujourd’hui), en 1932 existe un número-Monografía sobre los hermanos Perret, escrita por Pierre Vago, en 1946 se consolida como revista mensual y bajo la fundación de Andre Bloc. El primer número de AA que tengo en mi biblioteca es el número 34 (febrero-Marzo) de 1951. Mediante la lectura observada de una colección como AA, la determinación de unos capítulos representativos y la elección de imágenes de su tiempo se explican estos 57 años de arquitectura, cuyos resultados de un proceso temporal disfrutamos desde hace aproximadamente veinte años. A principio de los años cincuenta un grupo de jóvenes arquitectos, denso e intercomunicado en los congresos CIAM se propone situar la realidad de la arquitectura en los principios y realidades de su tiempo y de los que se intuyen futuro. Resultados de la Segunda Gran Guerra no son solo tragedias humanas sino gran investigación y desarrollo concretada industrialmente, enormes movimientos de personas en Europa y una sociedad enormemente optimista en USA, todo esto producirá las grandes transformaciones sociales de los 60’ y sus concreciones tecnológicas, políticas y desarrollo. Muchos arquitectos, publicaciones, concursos o decisiones políticas o privadas han producido el catalogo de arquitecturas de estos años, desde el CIAM IX hasta el POMPIDOU, desde la casa GEHRY hasta el KUNSTHAL, desde BRASILIA hasta SIDNEY, desde COPLEJIDAD Y CONTRADICCIÓN hasta DELIRIOS DE NY, desde OSAKA hasta MUNICH. En todas han existido un esfuerzo enorme por concretar la realidad de nuestras aspiraciones desde las puramente ideológicas de introspección social, hasta las concreciones de imagen directa. Varias líneas he abierto en mi proceso de investigación, las he llamado “anillos” porque todas estas líneas tienen similitud con los “anillos de crecimiento” de los árboles en cuanto a como se presentan en la estructura de formación y ha la cantidad de información no solo interna sino externa que aportan sobre la estructura árbol, su medio y la historia. Igual que podemos saber las temperaturas o las pluviometría que cubrieron Europa en la edad media solo estudiando los anillos de crecimiento de nuestro árboles (su grosor), de igual forma repasando LOS CONCURSOS y sus resultados que existieron en los últimos cincuenta años, podemos entender las aspiraciones y concreciones de las sociedades y sus arquitectos en este tiempo. Cuatro capítulos, los mas determinantes son los elegidos para dar cuerpo a una TESIS de tamaño capaz: Las ideas, el futuro, las referencias y el presente son los capítulos que de forma visual intentan explicar el fruto arquitectónico, sus aspiraciones y sus concreciones. Las ideas sin ninguna duda, pertenecen a los padres de nuestro tiempo, son las del Team X, la reflexión sobre lo perecedero, las realidades programáticas, densidades o lo publico-privado son solo planetas en el universo de sus ideas. El futuro lo trazaron aquellos que empezaron a investigar, concretar o reflexionar sobre la incidencia tanto de los procesos industriales con sus nuevos materiales como de las nuevas concreciones urbanas que los movimientos migratorios producirían en las ciudades. Las referencias son las bibliotecas de carácter informativo-visual que han generado nuestro inventario icónico. El presente son las imágenes de referencia de nuestro tiempo-mediático, no solo las produce un arquitecto (en este caso R.Koolhas), pero si que es verdad que en las imágenes arquitectónicas de OMA se concreta todo el catalogo de arquitecturas del presente. ENGLISH SUMMARY The fisrt AA (l´Architecture d´Aujourd´hui) issue was published in 1929, three years later, in 1932, a monographic issue on Perret brothers was written by Pierre Vago and in 1946 the magazine was strongly established as a monthly publication under the direction of André Bloc. The oldest copy I own on my bookshelves is nº 34 printed in February-March 1951. While carefully reading a collection such as AA we are able to extract representative chapters and images that can explain a linear process lasting 57 years of fruitful architectural production of which consequences we have been enjoying the past twenty years. In the early fifties a compact group of young architects linked by the CIAM congress decided to encompass architectural reality to the needs and principles of their time. Not only big human tragedies arose from the Second World War but also some of the fastest industrial inventions due to a powerful will to development, that altogether with european migrations and a high standard of optimism in the United States headed to the peak transformations of the sixties and their technological and political development. A bunch of architects, magazines and architectural competitions sided by political and private decisions produced the architectural catalogue of those years, from CIAM IX to the Pompidou art centre, from Gerhy´s house to the Kunsthal museum, from Brasilia to Sidney, from “Complexity and Contradiction“ to “Delirious NY” and from Osaka all the way to Munich. All of them carried a vast effort towards the concretion of will, from social introspection to a more effective development of images. Several paths run across my investigation, namely “the rings”, as they tend to behave as a growing structure like a tree trunk, providing internal and external information not only of the vegetal element but also of the environment and events crossing its time. In the same direction as we are able to predict the weather in the Middle Age by means of studying our forests, we can use the architectural competitions ant their results for the past fifty years to understand the will and ambitions of these developing societies and their architects. To give shape to a sizeable thesis the selected information has been packed in four chapters: Ideas, Future, References and Present, each of them structured as an Image bank visualizing the architectural product, its will and specific ambition. The first group, Ideas, is devoted entirely to the step-fathers of present architecture, with ideas that belong to TEAM X and embrace the reflection about the transitory, the programmatic reality, density or the public-private debate as wandering planets of their ideal universe. The second group is dedicated to a Future that was traced by those engaged on industrial processes and new material investigation together with some others exploring new urban concretions brought to existence by the pressure of the after war migrations. The third group, References, have been shaped as a stock-list containing all our iconic cross-references. The last group, Present, brings together the icons of this media-time we live in and not only those produced by one single architect (Rem Koolhaas) even if his production embodies all architectural references at the moment.

Digital Control Implementation to Reduce the Cost and Improve the Performance of the Control Stage of an Industrial Switched-Mode Power Supply

The main objective of this work is the design and implementation of the digital control stage of a 280W AC/DC industrial power supply in a single low-cost microcontroller to replace the analog control stage. The switch-mode power supply (SMPS) consists of a PFC boost converter with fixed frequency operation and a variable frequency LLC series resonant DC/DC converter. Input voltage range is 85VRMS-550VRMS and the output voltage range is 24V-28V. A digital controller is especially suitable for this kind of SMPS to implement its multiple functionalities and to keep the efficiency and the performance high over the wide range of input voltages. Additional advantages of the digital control are reliability and size. The optimized design and implementation of the digital control stage it is presented. Experimental results show the stable operation of the controlled system and an estimation of the cost reduction achieved with the digital control stage.

Multiphase transformer-coupled converter: two different strategies for energy conversion

The operation of a multiphase topology, ideally, without energy storage presents the advantage of achieving very high efficiency over a wide load range as well as a fast dynamic response. However, ideal no-energy storage operation also implies a limitation in the regulation capability of the topology, the output voltage can only take discrete values. These features (high efficiency and discrete regulation capability) of the proposed energy conversion strategy enable the topology as a candidate for `DC-DC transformer' applications. The advantages, drawbacks and the operating principle of this concept, implemented with a `closed chain' magnetic structure have been already presented. In this work, the minimum energy storage operation, is applied to two different magnetic structures. These magnetic structures are called `closed chain' and `pyramidal' the main advantage of the `pyramidal' coupling structure is to improve the size of the converter without increasing the operating frequency. Both magnetic structures are analyzed, compared and experimentally implemented.

Nueva terminal de pasajeros para el aeropuerto Federico García Lorca, Granada - Jaén

El presente proyecto de construcción define las actuaciones para la ejecución de la Nueva Terminal de pasajeros para el aeropuerto Federico García Lorca, Granada – Jaén, situado entre los términos municipales de Chauchina y Santa Fe, en la provincia de Granada. Estudios realizados por AENA, en colaboración con el Ministerio de Fomento, dejan constancia de los déficits en cuanto a capacidad de las instalaciones del aeropuerto se refiere, en múltiples facetas. En el caso de la terminal de pasajeros, sus principales elementos de servicio han sido sometidos a estudio, revelando claras faltas en numerosos puntos. El más relevante son las carencias en cuanto a capacidad, respecto a la demanda existente, y especialmente la demanda prevista para un cierto horizonte de estudio. Además, las nuevas normativas de aplicación en aeropuertos internacionales publicadas por la International Air Transport Association (IATA) entran en conflicto con ciertos parámetros de diseño de las instalaciones actuales. Se requiere una remodelación del conjunto para adaptarse a estas exigencias de validez internacional.

Morphological and germination response variability in seeds of wild yellow gentian (Gentiana lutea L.) accessions from northwest Spain

Gentiana lutea L. (yellow gentian, Gentianaceae) is an important medicinal plant under protection as endangered species in most European countries. The aim of this work was to evaluate variation in seed mass, seed water content, and seed germination among 56 wild accessions of G. lutea. The effect of gibberellic acid (GA3), putrescine, moist chilling, and level of ripeness of seeds on subsequent germination was also investigated. Seeds of G. lutea showed physiological dormancy (final germination percentages ranged from 0% to 11%, depending on the accession) and GA3 enhanced seed germination drastically in all the accessions. The highest germination (99%) of GA3-treated seeds was reached at 15 °C. Final germination percentage and germination rate (as expressed by mean germination time), as well as seed mass and seed water content, varied significantly among accessions. In general, 1 year moist chilling did not significantly enhance G. lutea seed germination. For most accessions, no significant differences were found between fully ripe seeds and less ripe seeds for seed water content, seed mass, and seed germination. Applications of GA3 were always most effective than those of putrescine for increasing seed germination.

Ferromagnetic resonance and magnetooptic study of submicron epitaxial Fe(001) stripes

We present a combined magnetooptic and ferromagnetic resonance study of a series of arrays of single-crystalline Fe stripes fabricated by electron beam lithography on epitaxial Au(001)/Fe(001)/MgO(001) films grown by pulsed laser deposition. The analysis of the films revealed a clear fourfold magnetocrystalline anisotropy, with no significant presence of other anisotropy sources. The use of a large series of arrays, with stripe widths between 140 and 1000 nm and separation between them of either 200 nm or 500 nm, allowed studying their magnetization processes and resonance modes as well as the effects of the dipolar interactions on both. The magnetization processes of the stripes were interpreted in terms of a macrospin approximation, with a good agreement between experiments and calculations and negligible influence of the dipolar interactions. The ferromagnetic resonance spectra evidenced two types of resonances linked to bulk oscillation modes, essentially insensitive to the dipolar interactions, and a third one associated with edge-localized oscillations, whose resonance field is strongly dependent on the dipolar interactions. The ability to produce a high quality, controlled series of stripes provided a good opportunity to achieve an agreement between the experiments and calculations, carried out by taking into account just the Fe intrinsic properties and the morphology of the arrays, thus evidencing the relatively small role of other extrinsic factors.

Detailed damage mechanisms assessment in composite materials by means of X-ray tomography

This research focused on the evaluation of damage formation on ±45º carbon fiber laminates subjected to tensile tests. The damage was evaluated by means of X-ray tomography. A high density of cracks developed during the plateau of the stress-strain curve and were qualitatively analyzed, showing that the inner plies eventually developed a higher crack concentration than the outer plies. Delamination started to occur in the outermost ply interface when the slope after the plateau of the stress-strain curve began to increase.

Scaling of the coercivity with the geometrical parameters in epitaxial Fe antidot arrays

We studied a series of square lattice antidot arrays, with diameter and lattice parameter from hundreds of nanometers to some microns, fabricated using two lithography techniques in epitaxial Fe(001) films. The coercivity increase of each array with respect to its base film can be scaled to a simple geometric parameter, irrespective of the lithography technique employed. Magnetic transmission x-ray microscopy studies, in arrays fabricated on polycrystalline Fe films deposited on silicon nitride membranes, evidenced the propagation of reversed domains from the edges of the arrays, in agreement with the coercivity analysis of the epitaxial arrays and with micromagnetic models.

Monitorización y seguimiento del esfuerzo realizado por los estudiantes y de su asistencia a actividades presenciales

Este artículo documenta el planteamiento, la metodología y los primeros resultados de un plan de monitorización detallada del esfuerzo y de asistencia a actividades presenciales por parte de los estudiantes de las titulaciones ofertadas por la Escuela Técnica Superior de Ingenieros Navales de la Universidad Politécnica de Madrid durante el segundo cuatrimestre del curso 2011-2012. Se ha establecido un sistema mecánico de recogida de datos de esfuerzo por parte de los estudiantes utilizando una hoja tipo test especialmente configurada al efecto. Se pasa una hoja en todas y cada una de las actividades presenciales realizadas y en la hoja se solicita información sobre el trabajo "fuera de clase". Se documenta en este artículo cómo se ha estructurado esa hoja, qué tipo de datos se recogen, cómo se tratan mediante una base de datos creada al efecto, qué tipo de análisis se puede realizar y qué resultados preliminares obtenemos de dichos análisis.

Development and implementation of a virtual laboratory for training process improvement in the mechanics of continuous media

The project arises from the need to develop improved teaching methodologies in field of the mechanics of continuous media. The objective is to offer the student a learning process to acquire the necessary theoretical knowledge, cognitive skills and the responsibility and autonomy to professional development in this area. Traditionally the teaching of the concepts of these subjects was performed through lectures and laboratory practice. During these lessons the students attitude was usually passive, and therefore their effectiveness was poor. The proposed methodology has already been successfully employed in universities like University Bochum, Germany, University the South Australia and aims to improve the effectiveness of knowledge acquisition through use by the student of a virtual laboratory. This laboratory allows to adapt the curricula and learning techniques to the European Higher Education and improve current learning processes in the University School of Public Works Engineers -EUITOP- of the Technical University of Madrid -UPM-, due there are not laboratories in this specialization. The virtual space is created using a software platform built on OpenSim, manages 3D virtual worlds, and, language LSL -Linden Scripting Language-, which imprints specific powers to objects. The student or user can access this virtual world through their avatar -your character in the virtual world- and can perform practices within the space created for the purpose, at any time, just with computer with internet access and viewfinder. The virtual laboratory has three partitions. The virtual meeting rooms, where the avatar can interact with peers, solve problems and exchange existing documentation in the virtual library. The interactive game room, where the avatar is has to resolve a number of issues in time. And the video room where students can watch instructional videos and receive group lessons. Each audiovisual interactive element is accompanied by explanations framing it within the area of knowledge and enables students to begin to acquire a vocabulary and practice of the profession for which they are being formed. Plane elasticity concepts are introduced from the tension and compression testing of test pieces of steel and concrete. The behavior of reticulated and articulated structures is reinforced by some interactive games and concepts of tension, compression, local and global buckling will by tests to break articulated structures. Pure bending concepts, simple and composite torsion will be studied by observing a flexible specimen. Earthquake resistant design of buildings will be checked by a laboratory test video.

Optimization of curing cycle in carbon fiber-reinforced laminates: Void distribution and mechanical properties

A strategy is presented to optimize out-of-autoclave processing of quasi-isotropic carbon fiber-reinforced laminates. Square panels of 4.6 mm nominal thickness with very low porosity ð6 0:2%Þ were manufactured by compression molding at low pressure (0.2 MPa) by careful design of the temperature cycle to maximize the processing window. The mechanisms of void migration during processing were ascertained by means of X-ray microtomography and the effect of ply clustering on porosity and on void shape was explained. Finally, the effect of porosity and ply clustering on the compressive strength before and after impact was studied.