Temperature controlled light-emitting diode lamp for photovoltaic rural applications

In recent years, interest in light-emitting diode (LED) lighting has been growing because of its high efficacy, lifetime and ruggedness. This paper proposes a better adaptation of LED lamps to the technical requirements of photovoltaic lighting domestic systems, whose main quality criteria are reliability and that behave as voltage power supplies. As the key element of reliability in LED lamps is temperature, a solution is proposed for driving LED lamps using voltage sources, such as photovoltaic system batteries, with a control architecture based on pulse width modulation signal that regulates the current applied according to the LED lamp temperature. A prototype of the LED lamp has been implemented and tested to show its good performance at different temperatures and at different battery voltages.

The scenario of two-dimensional instabilities of the cylinder wake under EHD forcing: A linear stability analysis

We propose to study the stability properties of an air flow wake forced by a dielectric barrier discharge (DBD) actuator, which is a type of electrohydrodynamic (EHD) actuator. These actuators add momentum to the flow around a cylinder in regions close to the wall and, in our case, are symmetrically disposed near the boundary layer separation point. Since the forcing frequencies, typical of DBD, are much higher than the natural shedding frequency of the flow, we will be considering the forcing actuation as stationary. In the first part, the flow around a circular cylinder modified by EHD actuators will be experimentally studied by means of particle image velocimetry (PIV). In the second part, the EHD actuators have been numerically implemented as a boundary condition on the cylinder surface. Using this boundary condition, the computationally obtained base flow is then compared with the experimental one in order to relate the control parameters from both methodologies. After validating the obtained agreement, we study the Hopf bifurcation that appears once the flow starts the vortex shedding through experimental and computational approaches. For the base flow derived from experimentally obtained snapshots, we monitor the evolution of the velocity amplitude oscillations. As to the computationally obtained base flow, its stability is analyzed by solving a global eigenvalue problem obtained from the linearized Navier–Stokes equations. Finally, the critical parameters obtained from both approaches are compared.

VLC-based light-weight portable user interface for in-house applications.

Advances in solid-state lighting have overcome common limitations on optical wireless such as power needs due to light dispersion. It's been recently proposed the modification of lamp's drivers to take advantages of its switching behaviour to include data links maintaining the illumination control they provide. In this paper, a remote access application using visible light communications is presented that provides wireless access to a remote computer using a touchscreen as user interface

Testing of fluorescent DC lamps for Solar Home Systems

With the advent of the Universal Technical Standard for Solar Home Systems, procedures to test the compliance of SHS fluorescent lamps with the standard have been developed. Definition of the laboratory testing procedures is a necessary step in any lamp quality assurance procedure. Particular attention has been paid to test simplicity and to affordability, in order to facilitate local application of the testing procedures, for example by the organisations which carry out electrification programmes. The set of test procedures has been applied to a representative collection of 42 lamps from many different countries, directly acquired in the current photovoltaic rural electrification market. Tests apply to: lamp resistance under normal operating conditions; lamp reliability under extreme conditions; under abnormal conditions; and lamp luminosity. Results are discussed and some recommendations for updating the relevant standard are given. The selected technical standard, together with the proposed testing procedures, form the basis of a complete quality assurance tool that can be applied locally in normal electrical laboratories. Full testing of a lamp requires less than one month, which is very reasonable on the context of quality assurance programmes

Estudio de las formas de aplicación de la fotografía sobre los materiales pétreos para la arquitectura = Study of photography application methods over architectural stony materials

Desde que el Hombre era morador de las cavernas ha sido manifiesto su deseo innato por grabar y reproducir "instantáneas con las que perpetuarse o sobre las que mirarse ". La aparición y desarrollo de la fotografía como medio para poder captar y fijar "la imagen directa de la realidad circundante " pronto se convierte en un nuevo lenguaje estético y poético que permite al artista la interpretación y reflexión de lo observado. Se imprime a la imagen el carácter de la mirada del fotógrafo, estableciendo un diálogo conceptual con el juego de luces. La presente Tesis plantea la creación de una nueva piel de arquitectura mediante la impresión fotográfica sobre materiales pétreos. La búsqueda de la expresividad de los materiales como soporte de expresión artística implica un cambio de escala al trasladar la instantánea fotográfica a la arquitectura y la aplicación de un nuevo soporte al imprimir la fotografía sobre materiales arquitectónicos. Se justifica la elección del dispositivo láser CO2 como sistema de impresión fotográfica sobre los materiales pétreos arquitectónicos, como la técnica que permite la unión física de la imagen y el proyecto arquitectónico, generando un valor añadido a través del arte de la fotografía. Se justifica la elección de los materiales investigados, Silestone® Blanco Zeus y GRC® con TX Active® Aria, de forma que la investigación de esta nueva piel de arquitectura abarca tanto la envolvente del edificio como su volumen interior, permitiendo cerrar el círculo arquitectónico "in&out" y dota al proyecto arquitectónico de un valor añadido al introducir conceptos sostenibles de carácter estético y medioambiental. Se realiza una consulta a las empresas del sector arquitectónico relacionadas directamente con la producción y distribución de los materiales Silestone® y GRC®, así como a las empresas especializadas en sistemas de impresión fotográfica sobre materiales, acerca del estado del arte. Se recorre la Historia de la fotografía desde sus orígenes hasta el desarrollo de la era digital y se analiza su condición artística. Se recopilan los sistemas de impresión fotográfica que han evolucionado en paralelo con los dispositivos de captura de la instantánea fotográfica y se describe en profundidad el sistema de impresión fotográfica mediante dispositivo láser CO2. Se describen los procesos de fabricación, las características técnicas, cualidades y aplicaciones de los materiales pétreos arquitectónicos Silestone® Blanco Zeus y GRC® con TX Active® Aria. Se explica la técnica utilizada para la captación de la imagen fotográfica, su justificación artística y su proceso de impresión mediante dispositivo láser CO2 bajo diferentes parámetros sobre muestras de los materiales arquitectónicos investigados. Se comprueba la viabilidad de desarrollo de la nueva piel de arquitectura sobre Silestone® Blanco Zeus y GRC® con TX Active® Aria sometiendo a las piezas impresas bajo diferentes parámetros a tres ensayos de laboratorio. En cada uno de ellos se concreta el objetivo y procedimiento del ensayo, la enumeración de las muestras ensayadas y los parámetros bajo los que han sido impresas, el análisis de los resultados del ensayo y las conclusiones del ensayo. Ensayo de amplitud térmica. Se determina el grado de afectación de las imágenes impresas bajo la acción de contrastes térmicos. Series de muestras de Silestone® Blanco Zeus y GRC® con TX Active® Aria impresas con láser CO2 se someten a ciclos de contraste frío-calor de 12 horas de duración para una amplitud térmica total de 102°C. Se realiza una toma sistemática de fotografías microscópicas con lupa de aumento de cada pieza antes y después de los ciclos frío-calor y la observación de las transformaciones que experimentan los materiales bajo la acción del láser CO2. Ensayo de exposición a la acción de la radiación ultravioleta (UV). Se determina el grado de afectación de las imágenes impresas al activar la capacidad autolimpiante de partículas orgánicas. Una serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a ciclos de exposición de radiación ultravioleta de 26 horas de duración. Se somete la serie a un procedimiento de activación del aditivo TX Active®. Se simula la contaminación orgánica mediante la aplicación controlada de Rodamina B, tinte orgánico, y se simula la radiación UV mediante el empleo de una bombilla de emisión de rayos ultravioleta. Se realiza una toma sistemática de fotografías macroscópicas de la serie de muestras ensayadas: antes de aplicación de la Rodamina B, momento 00:00h, momento 04:00h y momento 26:00h del ensayo. Se procede a la descarga y análisis del histograma de las fotografías como registro de la actividad fotocatalítica. Ensayo de la capacidad autodescontaminante del GRC® con TX Active® impreso con láser CO2. Se comprueba si la capacidad autodescontaminante del GRC® con TX Active® se ve alterada como consecuencia de la impresión de la imagen fotográfica impresa con láser CO2. Serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a test de capacidad autodescontaminante: atmósfera controlada y contaminada con óxidos de nitrógeno en los que se coloca cada pieza ensayada bajo la acción de una lámpara de emisión de radiación ultravioleta (UV). Se registra la actividad fotocatalítica en base a la variación de concentración de óxido de nitrógeno. Se recopila el análisis e interpretación de los resultados de los ensayos de laboratorio y se elaboran las conclusiones generales de la investigación. Se sintetizan las futuras líneas de investigación que, a partir de las investigaciones realizadas y de sus conclusiones generales, podrían desarrollarse en el ámbito de la impresión fotográfica sobre materiales arquitectónicos. Se describe el rendimiento tecnológico y artístico generado por las investigaciones previas que han dado origen y desarrollo a la Tesis Doctoral. ABSTRACT Since ancient time, humanity has been driven by an innate wish to reproduce and engrave "snapshots that could help to perpetúate or to look at one self". Photography's birth and its development as a mean to capture and fix "the direct image of the surrounding reality" quickly becomes a new aesthetical and poetical language allowing the artist to interpret and think over what has been observed. The photographer's eye is imprinted onto the image, and so the conceptual dialogue between the artist and the light beams begins. The current thesis suggests the creation of a new architectural skin through photography imprinting over stony materials. The search for material's expressiveness as a medium of artistic expression involves a change of scale as it transfers photographic snapshot into architecture and the use of a new photographic printing support over architectural materials. CO2 laser is the chosen printing system for this technique as it allows the physical union of the image and the architectonic project, generating an added value through the art of photography. The researched materials selected were Silestone®, Blanco Zeus and GRC® with TX Active® Aria. This new architectural skin contains the building surrounding as well as its interior volume, closing the architectonic "in & out" circle and adding a value to the project by introducing aesthetical and environmental sustainable concepts. Architecture companies related to the production and distribution of materials like Silestone® and GRC®, as well as companies specialized in photography printing over materials were consulted to obtain a State of the Art. A thorough analysis of photography's History from its origins to the digital era development was made and its artistic condition was studied in this thesis. In this study the author also makes a compilation of several photographic printing systems that evolved together with photographic snapshot devices. The CO2 laser-based photographic printing system is also described in depth. Regarding stony materials of architecture like Silestone®, Blanco Zeus and GRC® with TX Active® Aria, the present study also describes their manufacture processes as well as technical features, quality and application. There is also an explanation about the technique to capture the photographic image, its artistic justification and its CO2 laser-based printing system over the researched materials under different parameters. We also tested the feasibility of this new architectural skin over Silestone® Blanco Zeus and GRC® with TX Active® Aria. The pieces were tested under different parameters in three laboratory trials. Each trial comprises of an explanation of its objective and its process, the samples were numbered and the printing parameters were specified. Finally, with the analysis of the results some conclusions were drawn. In the thermal amplitude trial we tried to determine how printed images were affected as a result of the action of thermal contrasts. Series of samples of Silestone® Blanco Zeus and GRC® with TX Active® Aria printed with CO2 laser were subjected to several 12h warm-cold cycles for thermal total amplitude of 102oc. Each sample was captured systematically with microscopic enhanced lenses before and after cold-warm cycles. The changes experienced by these materials under the effect of CO2 laser were observed and recorded. Trial regarding the Ultraviolet Radiation (UR) effect on images. We determined to which extent printed images were affected once the self-cleaning organic particles were activated. This time GRC® with TX Active® Aria samples printed with CO2 laser were exposed to a 26h UR cycle. The samples were subjected to the activation of TX Active® additive. Through the controlled application of Rodamine B and organic dye we were able to simulate the organic contamination process. UR was simulated using an ultraviolet beam emission bulb. A systematic capture of macroscopic pictures of the tested sample series was performed at different time points: before Rodamine B application, at moment 00:00h, moment 04:00h and moment 26:00h of the trial. Picture's histogram was downloaded and analyzed as a log of photocatalytic activity. Trial regarding the self-decontaminating ability of GRC® with TX Active® printed with CO2 laser. We tested if this self-decontaminating ability is altered as a result of CO2 laser printed image. GRC® with TX Active® Aria samples printed with CO2 laser, were subject to self-decontaminating ability tests with controlled and nitrogen oxide contaminated atmosphere. Each piece was put under the action of an UR emission lamp. Photocatalytic activity was recorded according to the variation in nitrogen oxide concentration. The results of the trial and their interpretation as well as the general conclusions of the research are also compiled in the present study. Study conclusions enable to draw future research lines of potential applications of photographic printing over architecture materials. Previous research generated an artistic and technological outcome that led to the development of this doctoral thesis.

Emissions and economic costs of cycling compact fluorescent lamps with integrated ballasts

This paper proposes a way to quantify the emissions of mercury (Hg) and CO2 associated with the manufacture and operation of compact fluorescent lamps with integrated ballasts (CFLis), as well as the economic cost of using them under different operating cycles. The main purpose of this paper is to find simple criteria for reducing the polluting emissions under consideration and the economic cost of CFLi to a minimum. A lifetime model is proposed that allows the emissions and costs to be described as a function of degradation from turning CFLi on and their continuous operation. An idealized model of a CFLi is defined that combines characteristics stated by different manufacturers. In addition, two CFLi models representing poor-quality products are analyzed. It was found that the emissions and costs per unit of time of operation of the CFLi depend linearly on the number of times per unit of time it is turned on and the time of continuous operation. The optimal conditions (lowest emissions and costs) depend on the place of manufacture, the place of operation and the quality of the components of the lamp/ballast. Finally, it was also found that for each lamp, there are intervals when it is turned off during which emissions of pollutants and costs are identical regardless of how often the lamp is turned on or the time it remains on. For CO2 emissions, the lamp must be off up to 5 minutes; for the cost, up to 7 minutes and for Hg emissions, up to 43 minutes. It is advisable not to turn on a CFLi sooner than 43 minutes from the last time it was turned off.

Indoor characterization at production sccale: 200 kWp of CPV solar simulator measurements

In order to complement ISFOC’s characterization capabilities, a Helios 3198 CPV Solar Simulator was installed in summer 2010. This Solar Simulator, based on a parabolic mirror and a high-intensity, small area Xenon flash lamp was developed by the Instituto de Energía Solar in Madrid [1] and is manufactured and distributed by Soldaduras Avanzadas [2]. This simulator is used not only for R&D purposes, but as a quality control tool for incoming modules that are to be installed in ISFOC’s CPV plants. In this paper we will discuss the results of recent measurements of close to 5000 modules, the entire production of modules corresponding to a small CPV power plant (200 kWp). We scrutinize the resultant data for signs of drift in the measurements, and analyze the light quality before and after, to check for changes in spectrum or spatial uniformity.)

Circuito de disparo de lámparas flash para la iluminación de sistemas fotovoltaicos

La medición y testeo de células fotovoltaicas en el laboratorio o en la industria exige reproducir unas condiciones de iluminación semejantes a las reales. Por eso se utilizan sistemas de iluminación basados en lámparas flash de Xenon que reproducen las condiciones reales en cuanto a nivel de irradiancia y espectro de la luz incidente. El objetivo de este proyecto es realizar los circuitos electrónicos necesarios para el disparo de dichas lámparas. El circuito de alimentación y disparo de una lámpara flash consta de una fuente de alimentación variable, un circuito de disparo para la ionización del gas Xenon y la electrónica de control. Nuestro circuito de disparo pretende producir pulsos adecuados para los dispositivos fotovoltaicos tanto en irradiancia, espectro y en duración, de forma que con un solo disparo consigamos el tiempo, la irradiancia y el espectro suficiente para el testeo de la célula fotovoltaica. La mayoría de estos circuitos exceptuando los específicos que necesita la lámpara, serán diseñados, simulados, montados en PCB y comprobados posteriormente en el laboratorio. ABSTRACT. Measurement and testing of photovoltaic cells in the laboratory or in industry requires reproduce lighting conditions similar to the real ones. So are used based lighting systems xenon flash lamps that reproduce the actual conditions in the level of irradiance and spectrum of the incident light. The objective of this project is to make electronic circuits required for such lamps shot. The power supply circuit and flash lamp shot consists of a variable power supply, a trigger circuit for Xenon gas ionization and the control electronics. Our shot circuit aims to produce pulses suitable for photovoltaic devices both irradiance, spectrum and duration, so that with a single shot get the time, the irradiance and spectrum enough for testing the photovoltaic cell. Most of these circuits except lamp specific requirements will be designed, simulated, and PCB mounted subsequently tested in the laboratory.

Análisis de la aplicación de Soldadura de acero de calidad "A" mediante láser de Neodimio-YAG en construcción naval

El proceso de soldadura por láser desarrollado en los últimos años ha puesto de manifiesto las posibilidades de aplicación de esta tecnología en diferentes sectores productivos, principalmente en la industria automovilística, en la cual se han demostrado sus ventajas en términos de productividad, eficiencia y calidad. El uso de la tecnología láser, ya sea híbrida o pura, reduce el input térmico al limitar la zona afectada por el calor, sin crear deformaciones y, por tanto, disminuye los re-trabajos post-soldadura necesarios para eliminarlas. Asimismo, se aumenta la velocidad de soldadura, incrementando la productividad y calidad de las uniones. En la última década, el uso de láseres híbridos, (láser + arco) de gran potencia de Neodimio YAG, (Nd: YAG) ha sido cada vez más importante. La instalación de este tipo de fuentes de láser sólido de gran potencia ha sido posible en construcción naval debido a sus ventajas con respecto a las instalaciones de láser de C02 existentes en los astilleros que actualmente utilizan esta tecnología. Los láseres de C02 están caracterizados por su gran potencia y la transmisión del haz a través de espejos. En el caso de las fuentes de Nd:YAG, debido a la longitud de onda a la cual se genera el haz láser, su transmisión pueden ser realizada a través de fibra óptica , haciendo posible la utilización del cabezal láser a gran distancia de la fuente, aparte de la alternativa de integrar el cabezal en unidades robotizadas. El proceso láser distribuye el calor aportado de manera uniforme. Las características mecánicas de dichas uniones ponen de manifiesto la adecuación de la soldadura por láser para su uso en construcción naval, cumpliendo los requerimientos exigidos por las Sociedades de Clasificación. La eficiencia energética de los láseres de C02, con porcentajes superiores al 20%, aparte de las ya estudiadas técnicas de su instalación constituyen las razones por las cuales este tipo de láser es el más usado en el ámbito industrial. El láser de gran potencia de Nd: YAG está presente en el mercado desde hace poco tiempo, y por tanto, su precio es relativamente mayor que el de C02, siendo sus costes de mantenimiento, tanto de lámparas como de diodos necesarios para el bombeo del sólido, igualmente mayores que en el caso del C02. En cambio, el efecto de absorción de parte de la energía en el plasma generado durante el proceso no se produce en el caso del láser de Nd: YAG, utilizando parte de esa energía en estabilizar el arco, siendo necesaria menos potencia de la fuente, reduciendo el coste de la inversión. En función de la aplicación industrial, se deberá realizar el análisis de viabilidad económica correspondiente. Dependiendo de la potencia de la fuente y del tipo de láser utilizado, y por tanto de la longitud de onda a la que se propaga la radiación electromagnética, pueden existen riesgos para la salud. El láser de neodimio se propaga en una longitud de onda, relativamente cercana al rango visible, en la cual se pueden producir daños en los ojos de los operadores. Se deberán establecer las medidas preventivas para evitar los riesgos a los que están expuestos dichos operadores en la utilización de este tipo de energía. La utilización del láser de neodimio: YAG ofrece posibilidades de utilización en construcción naval económicamente rentables, debido su productividad y las buenas características mecánicas de las uniones. Abstract The laser welding process development of the last years shows broad application possibilities in many sectors of industry, mostly in automobile production. The advantages of the laser beam process produce higher productivity, increasing the quality and thermal efficiency. Laser technology, arc-hybrid or pure laser welding, reduces thermal input and thus a smaller heat-affected zone at the work piece. This means less weldment distortion which reduces the amount of subsequent post-weld straightening work that needs to be done. A higher welding speed is achieved by use of the arc and the laser beam, increasing productivity and quality of the joining process. In the last decade use of hybrid technology (laser-GMA hybrid method) with high power sources Nd:YAG lasers, gained in importance. The installation of this type of higher power solid state laser is possible in shipbuilding industrial applications due to its advantages compare with the C02 laser sources installed in the shipyards which use this technology. C02 lasers are characterised by high power output and its beam guidance is via inelastic system of mirrors. In the case of Nd:YAG laser, due to its wavelength, the laser beam can be led by means of a flexible optical fibre even across large distances, which allows three dimensional welding jobs by using of robots. Laser beam welding is a process during which the heat is transferred to the welded material uniformly and the features of the process fulfilled the requirements by Classification Societies. So that, its application to the shipbuilding industry should be possible. The high quantum efficiency of C02 laser, which enabled efficiency factors up to 20%, and relative simple technical possibilities of implementation are the reasons for the fact that it is the most important laser in industrial material machining. High power Nd: YAG laser is established on the market since short time, so that its price is relatively high compared with the C02 laser source and its maintenance cost, lamp or diode pumped solid state laser, is also higher than in the case of C02 lasers. Nevertheless effect of plasma shielding does not exist with Nd:YAG lasers, so that for the gas-shielding welding process the optimal gases can be used regarding arc stability, thus power source are saved and the costs can be optimised. Each industrial application carried out needs its cost efficiency analysis. Depending on the power output and laser type, the dangerousness of reflected irradiation, which even in some meters distance, affects for the healthy operators. For the YAG laser process safety arrangements must be set up in order to avoid the laser radiation being absorbed by the human eye. Due to its wavelength of radiation, being relatively close to the visible range, severe damage to the retina of the eye is possible if sufficient precautions are not taken. Safety aspects are of vital importance to be able to shield the operator as well as other personal. The use of Nd:YAG lasers offers interesting and economically attractive applications in shipbuilding industry. Higher joining rates are possible, and very good mechanical/technological parameters can be achieved.

Variable impedance LED matrix control system for lamps in PV applications

The interest in LED lighting has been growing recently due to the high efficacy, lifelime and ruggedness that this technology offers. However the key element to guarantee those parameters with these new electronic devices is to keep under control the working temperature of the semiconductor crystal. This paper propases a LED lamp design that fulfils the requ irements of a PV lighting systems, whose main quality criteria is reliability. It uses directly as a power supply a non·stabilized constant voltage source, as batteries. An electronic control architecture is used to regulate the current applied to the LEO matri)( according to their temperature and the voltage output value of the batteries with two pulse modulation signals (PWM) signals. The first one connects and disconnects the LEOs to the power supply and the second one connects and disconnects several emitters to the electric circuit changing its overall impedance. A prototype of the LEO lamp has been implemented and tested at different temperaturas and battery voltages.

LED bulb lamps technical specification and testing procedure for solar home systems.

With the consolidation of the new solid state lighting LEOs devices, te5t1n9 the compliance 01 lamps based on this technology lor Solar Home Systems (SHS) have been analyzed. The definition of the laboratory procedures to be used with final products 15 a necessary step in arder to be able to assure the quality of the lamps prior to be installed [1]. As well as with CFL technology. particular attention has been given to simplicity and technical affordability in arder to facilitate the implementation of the test with basie and simple laboratory too15 even on the same SHS electrification program locations. The block of test procedures has been applied to a set of 14 low-cost lamps. They apply to lamp resistance, reliability and performance under normal, extreme and abnormal operating conditions as a simple but complete quality meter tool 01 any LEO bulb.

LED bulbs technical specification and testing procedure for solar home systems

The definition of technical specifications and the corresponding laboratory procedures are necessary steps in order to assure the quality of the devices prior to be installed in Solar Home Systems (SHS). To clarify and unify criteria a European project supported the development of the Universal Technical Standard for Solar Home Systems (UTSfSHS). Its principles were to generate simple and affordable technical requirements to be optimized in order to facilitate the implementation of tests with basic and simple laboratory tools even on the same SHS electrification program countries. These requirements cover the main aspects of this type of installations and its lighting chapter was developed based on the most used technology at that time: fluorescent tubes and CFLs. However, with the consolidation of the new LED solid state lighting devices, particular attention is being given to this matter and new procedures are required. In this work we develop a complete set of technical specifications and test procedures that have been designed within the frame of the UTSfSHS, based on an intense review of the scientific and technical publications related to LED lighting and their practical application. They apply to lamp reliability, performance and safety under normal, extreme and abnormal operating conditions as a simple but complete quality meter tool for any LED bulb.

Analysis of thermo-mechanical stress effects on CPV receiver under high intensity light cycles

After construction of the LYSS (Light cYcling Stressing Source) in early 2014, several CPV receivers, with and without secondary optical element (SOE) have been aged under fast transient illumination cycling,. The test plan for Madrid consisted of 50000 cycles. Receivers with poor heat spreaders showed low reliability but those with thicker metal layers passed the test well. The operation of LYSS along 8 months, after more than 250000 cycles, did not show any significant failure, except lamp reposition every 120 hours, in average. The equipment seems valid for unveiling weak receiver designs with respect to intensive illumination, in steady and transient modes.

Sol-gel TiO2 nanoparticles prompt photocatalytic cement for pollution degradation

TiO2 nanoparticles (TiO2NPs) prepared by the sol–gel method have been incorporated to cement paste with the aim of creating a photocatalytic system capable of compensating, through degradation of hazardous molecules, the envi- ronmental impact associated to the production of the clinker. Doping was carried out at different mass ratios with TiO2NPs precursor solutions within a fresh ce- ment paste, which was then characterized using scanning electron microscopy (SEM). The photocatalytic performance was evaluated by the degradation of Methylene Blue (MB) using a 125W UV lamp as irradiating source. Main cement properties such as hydration degree and C-S-H content are affected by TiO2NPs doping level. Cement containing TiO2NPs exhibited an increasing photocatalytic activity for increasing doping, while the pure cement paste control could hardly degrade MB. The kinetics of the system where also studied and their second order behavior related to microstructural aspects of the system.

Sistema de gestión de un banco de tiempo

RESUMEN El presente documento aborda la problemática surgida en torno al desarrollo de una plataforma para gestión de bancos de tiempo mediante tecnología LAMP (Linux + Apache + MySql + PHP). Se mostrarán los resultados del análisis de requisitos, la implementación, la puesta en práctica desde el año 2005, asi como conclusiones y líneas futuras. Para finalizar la documentación, se adjunta una guía para la creación de un banco de tiempo. ABSTRACT This document explains the solution to develop a time bank management platform, using LAMP technology (Linux + Apache + MySql + PHP). This will be focus on the result of the analysis, the implementation, the real implementation working since 2005, conclusions and future working lines. A guide to set up a time bank is attached at the end of the documentation.