Pantalla táctil para el piloto en un monoplaza de la fórmula SAE

En este proyecto se ha desarrollado un sistema electrónico para un vehículo de Fórmula SAE. La Fórmula SAE es una competición orientada a estudiantes que se basa en el diseño y fabricación de un vehículo de carreras. Este vehículo será posteriormente testeado en una competición a nivel mundial. El principal objetivo de este proyecto es el estudio, diseño y creación de un sistema para la visualización de información en un vehículo a través de una pantalla táctil. El núcleo del sistema será un microcontrolador de 32 bits de Microchip programado en C sobre un sistema de desarrollo integrado. El sistema mostrará información que pueda ser de utilidad para el piloto del coche. La información que se mostrará en la pantalla provendrá de los diferentes sensores del propio vehículo (velocidad, rpm, temperatura, estado de la batería). Dichos sensores se comunicarán con el sistema a través de comunicación CAN Bus. Para el testeo del sistema se utilizará una herramienta de simulación CAN. Además de mostrar información, el piloto será capaz de seleccionar entre diferentes configuraciones para la conducción desde el propio volante. El sistema contiene además los elementos necesarios para la programación y depuración del microcontrolador PIC. ABSTRACT. In this project, an electronic application for a Formula SAE vehicle has been developed. The Formula SAE is a student-oriented competition based on the design and manufacture of a race car. This car will be later tested in a worldwide competition. The principal aim of this project is the study, design and manufacture of a system for the display of a vehicle’s information through a touch screen. The system core will be a 32-bit Microchip microcontroller programmed in C code over an Integrated Development Environment. The system will display useful information to the car driver. The information shown on the screen will come from the different sensors of the vehicle itself (speed, rpm, temperature, battery status). Those sensors will communicate with the system via CAN Bus. A CAN Bus simulator device will be used during the design testing. In addition to displaying information, the pilot will be able to select different driving configurations from the steering wheel itself. The system also contains the necessary elements for programming and debugging the PIC microcontroller.

Sistema de control de tracción y salida para un monoplaza de la Fórmula SAE

En este proyecto de final de carrera se detalla el proceso de diseño, fabricación, montaje y ajuste de un dispositivo electrónico que sirva como sistema de control de tracción de un vehículo y que acoplaremos sobre un monoplaza de carreras que participa en la competición Formula SAE. La Formula SAE (Society of Automotive Engineers - Sociedad de Ingenieros de Automoción), es una competición de coches de carreras monoplaza a nivel universitario que promueve el desarrollo de la ingeniera aplicada a la automoción. Se pretende que este libro sirva de guía para el correcto manejo y desempeño del sistema fabricado. Además se ha pretendido que su lectura resulte fácil y comprensible para que la persona que lea este libro sea capaz de entender el sistema realizado para así poderlo mejorar. Gracias a la colaboración entre la Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación (ETSIST) de la Universidad Politécnica de Madrid (UPM), la Escuela de Ingenieros Industriales de esta misma Universidad (ETSII) y el Instituto Universitario de Investigación del Automóvil (INSIA), se sientan las bases de una plataforma docente en la cual se posibilita la formación y desarrollo de un vehículo tipo formula que participa en la ya mencionada competición Formula SAE. Para ello, se formo en el 2003 el equipo UPMRacing, primer representante español en el evento. El equipo se compone de más de 50 alumnos de la UPM y del Máster de Ingeniería en Automoción del INSIA. Es por tanto, en el vehículo fabricado por el equipo UPMRacing, en el que se pretende instalar este sistema de control de tracción. El control de tracción es un sistema de seguridad del automóvil diseñado para prevenir la perdida de adherencia cuando alguna rueda presenta deslizamiento, bien porque el conductor se excede en la aceleración o bien porque el firme este resbaladizo. La unidad de procesamiento del sistema de control de tracción fabricado lee la velocidad de cada rueda del vehículo mediante unos sensores y determina si existe deslizamiento, en tal caso, manda una señal a la centralita para disminuir la potencia hasta que el deslizamiento disminuya a unos valores controlados. El sistema cuenta con un control remoto que sirve como interfaz para que el piloto pueda manejarlo. Por ultimo, el dispositivo es capaz de conectarse a un bus de comunicaciones CAN para configurar ciertos parámetros. El objetivo del sistema es, básicamente, hacer que el coche no derrape en aceleraciones fuertes; concretamente en las salidas desde parado y al tomar una curva, aumentando así la velocidad en circuito y la seguridad del piloto. ABSTRACT. The purpose of this project is to describe the design, manufacture, assembly and adjustment processes of an electronic device acting as the traction control system (TCS) of a vehicle, that we will attach to a single-seater competition formula SAE car. The Formula SAE (Society of Automotive Engineers) is a graduate-level singleseater racing car competition promoting the development of automotive applied engineering. We also intend this work to serve as a technical user guide of the manufactured system. It is drafted clearly and concisely so that it will be easy for all those to whom it is addressed to understand and subject to further improvements. The close partnership among the Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación (ETSIST), Escuela de Ingenieros Industriales (ETSII) of Universidad Politécnica de Madrid (UPM), and the Instituto Universitario de Investigación del Automóvil (INSIA), lays the foundation of a teaching platform enabling the training and development of a single-seater racing car taking part in the already mentioned Formula SAE competition. In this respect, UPMRacing team was created back in 2003, first spanish representative in this event. The team consists of more than 50 students of the UPM and of INSIA Master in Automotive Engineering. It is precisely the vehicle manufactured by UPMRacing team where we intend to install our TCS. TCS is an automotive safety system designed to prevent loss of traction when one wheel has slip, either because the driver exceeds the acceleration or because the firm is slippery. The device’s central processing unit is able to detect the speed of each wheel of the vehicle via special sensors and to determine wheel slip. If this is the case, the system sends a signal to the ECU of the vehicle to reduce the power until the slip is also diminished to controlled values. The device has a remote control that serves as an interface for the pilot to handle it. Lastly, the device is able to connect to a communication bus system CAN to set up certain parameters. The system objective is to prevent skidding under strong acceleration conditions: standing-start from the starting grid or driving into a curve, increasing the speed in circuit and pilot’s safety.

Novel method to improve the signal-to-noise ratio in the far-field results obtained from planar near-field measurements

A method to reduce the noise power in far-field pattern without modifying the desired signal is proposed. Therefore, an important signal-to-noise ratio improvement may be achieved. The method is used when the antenna measurement is performed in planar near-field, where the recorded data are assumed to be corrupted with white Gaussian and space-stationary noise, because of the receiver additive noise. Back-propagating the measured field from the scan plane to the antenna under test (AUT) plane, the noise remains white Gaussian and space-stationary, whereas the desired field is theoretically concentrated in the aperture antenna. Thanks to this fact, a spatial filtering may be applied, cancelling the field which is located out of the AUT dimensions and which is only composed by noise. Next, a planar field to far-field transformation is carried out, achieving a great improvement compared to the pattern obtained directly from the measurement. To verify the effectiveness of the method, two examples will be presented using both simulated and measured near-field data.

Acondicionamiento y procesado de señales mediante bus CAN en vehículos monoplaza

En este proyecto se ha diseñado un sistema de adquisición y uso compartido de datos orientado a la implantación en un vehículo monoplaza de Formula SAE. Más concretamente, se encarga de recoger la información proporcionada por cuatro sensores infrarrojos de temperatura que sondearán constantemente la temperatura a la que se encuentran las ruedas del vehículo. La información, recogida en una memoria de almacenamiento masivo, se compartirá con otros dispositivos mediante un bus común. Los sensores empleados para generar la información los proporciona Melexis. Dichos sensores permiten estar todos simultáneamente conectados en un bus común gracias a su electrónica interna. Mediante el bus I2C irán conectados los cuatro sensores de nuestra aplicación (uno por cada rueda) permitiéndose añadir a posteriori más sensores o incluso otros elementos que permitan la comunicación por este tipo de bus I2C. La gestión de las tareas se realiza mediante el microcontrolador DSPIC33FJ256GP710-I/PF proporcionado por Microchip. Este es un microcontrolador complejo, por lo que para nuestra aplicación desaprovecharemos parte de su potencial. En nuestra tarjeta ha sido solamente añadido el uso de los dos I2C (uno para la tarjeta SD y el otro para los sensores), el módulo ECAN1 (para las comunicaciones por bus CAN), el módulo SPI (para acceder a una memoria Flash), 4 ADCs (para posibles mediciones) y 2 entradas de interrupción (para posible interactuación con el usuario), a parte de los recursos internos necesarios. En este proyecto se realiza tanto el desarrollo de una tarjeta de circuito impreso dedicada a resolver la funcionalidad requerida, así como su programación a través del entorno de programación facilitado por Microchip, el ICD2 Programmer. In this project, an acquisition and sharing system of data, which is oriented to be installed in a Formula SAE single-seater vehicle, has been designed. Concretely, it is responsible for getting the information supplied by four IR temperature sensors that monitor the wheels temperature. The information, which is loaded in a massive storage memory, will be shared with other devices by means of a common bus. The sensors used to generate the information are supplied by Melexis. Such specific sensors let that all they can be connected to the same bus at the same time due to their internal electronic. The four sensors will be connected through an I2C bus, one for each wheel, although we could add later more sensors or even other devices that they were able to let the I2C communication. Tasks management will be done by means of the DSPIC33FJ256GP710-I/PF microcontroller, which will be supplied by Microchip. This is a complex microcontroller, so, in our application we waste off a part of its potential. In our PCB has only been incorporated the use of the two I2C (one for the SD card and the other for the sensors), the ECAN module (to communicate devices), the SPI module (to access to the Flash memory), 4 ADC’s (for possible measurements) and 2 interrupt inputs (for possible inter-action with the user), a part of the necessary internal resources. This project aims the PCB development dedicated to solve the requested functionality and its programming through the programming environment provided by Microchip (the ICD2 programmer).

A hands-on education project: antenna design for inter-CubeSat communications

CubeSat platforms have become a de facto standard for universities willing to initiate space-technology activities with students. These small satellite platforms ease the implementation of hands-on education projects and opening the apertures of new research areas. Moreover, due to the limited volume (a 10 cm cube) and power (1 W), the application of imaginative solutions is mandatory. This leads to new innovation processes in the course of CubeSat projects. In this paper, we present a hands-on education project the aim of which is the specification, design, building and measurement of an antenna for communication between nanosatellites and, in particular, CubeSats. The project lies within the framework of ETSIT-UPM innovative education activities in the area of space technology, where students play a leading role in real engineering projects.

StreamCloud: An elastic and scalable data streaming system

Many applications in several domains such as telecommunications, network security, large scale sensor networks, require online processing of continuous data lows. They produce very high loads that requires aggregating the processing capacity of many nodes. Current Stream Processing Engines do not scale with the input load due to single-node bottlenecks. Additionally, they are based on static con?gurations that lead to either under or over-provisioning. In this paper, we present StreamCloud, a scalable and elastic stream processing engine for processing large data stream volumes. StreamCloud uses a novel parallelization technique that splits queries into subqueries that are allocated to independent sets of nodes in a way that minimizes the distribution overhead. Its elastic protocols exhibit low intrusiveness, enabling effective adjustment of resources to the incoming load. Elasticity is combined with dynamic load balancing to minimize the computational resources used. The paper presents the system design, implementation and a thorough evaluation of the scalability and elasticity of the fully implemented system.

Experimental determination of the eutectic temperature in air of the CuO-TiO2 pseudobinary system

Eutectic temperature and composition in the CuO–TiO2 pseudobinary system have been experimentally determined in air by means differential thermal analysis (DTA), thermogravimetry (TG) and hot-stage microscopy (HSM). Samples of the new eutectic composition treated at different temperatures have been characterized by X-ray diffraction (XRD) and X-ray absorption near-edge structural spectroscopy (XANES) to identify phases and to determine the Cu valence state, respectively. The results show that the eutectic temperature in air is higher by 100 °C (∼1000 °C) for a Ti-richer composition (XTiO2=25 mol%) than the one calculated in the literature. The reduction of Cu2+ to Cu+ takes places at about 1030 °C. The existence of Cu2TiO3 and Cu3TiO4 has been confirmed by XRD in the temperature range between 1045 and 1200 °C.

Space Debris Removal with an Ion Beam Shepherd Satellite: target-plasma interaction

A novel concept for active space debris removal known as Ion Beam Shepherd (IBS) which has been recently presented by our group is investigated. The concept makes use of a highly collimated ion beam to exert the necessary force on a generic debris to modify its orbit and/or attitude from a safe distance in a controlled manner, without the need of docking. After describing the main characteristics of the IBS system, some of the key aspects of thruster plasma and its interaction with the debris are studied, namely, (1) the modeling of the expansion of an plasma beam, based on the quasi-selfsimilarity exhibited by hypersonic plumes, (2) the characterization of the force and torque exerted upon the target debris, and (3) a preliminary evaluation of other plasma-body interactions.

Sistema para cambiar la geometría de un motor

En este proyecto se desarrolla un sistema electrónico para variar la geometría de un motor de un monoplaza que participa en la competición Fórmula SAE. Fórmula SAE es una competición de diseño de monoplazas para estudiantes, organizado por “Society of Automotive Enginners” (SAE). Este concurso busca la innovación tecnológica de la automoción, así como que estudiantes participen en un trabajo real, en el cual el objetivo es obtener resultados competitivos cumpliendo con una serie de requisitos. La variación de la geometría de un motor en un vehículo permite mejorar el rendimiento del monoplaza consiguiendo elevar el par de potencia del motor. Cualquier mejora en del vehículo en un ámbito de competición puede resultar determinante en el desenlace de la misma. El objetivo del proyecto es realizar esta variación mediante el control de la longitud de los tubos de admisión de aire o “runners” del motor de combustión, empleando un motor lineal paso a paso. A partir de la información obtenida por sensores de revoluciones del motor de combustión y la posición del acelerador se debe controlar la distancia de dichos tubos. Integrando este sistema en el bus CAN del vehículo para que comparta la información medida al resto de módulos. Por todo esto se realiza un estudio aclarando los aspectos generales del objetivo del trabajo, para la comprensión del proyecto a realizar, las posibilidades de realización y adquisición de conocimientos para un mejor desarrollo. Se presenta una solución basada en el control del motor lineal paso a paso mediante el microcontrolador PIC32MX795F512-L. Dispositivo del fabricante Microchip con una arquitectura de 32 bits. Este dispone de un módulo CAN integrado y distintos periféricos que se emplean en la medición de los sensores y actuación sobre el motor paso a paso empleando el driver de Texas Instruments DRV8805. Entonces el trabajo se realiza en dos líneas, una parte software de programación del control del sistema, empleando el software de Microchip MPLABX IDE y otra parte hardware de diseño de una PCB y circuitos acondicionadores para la conexión del microcontrolador, con los sensores, driver, motor paso a paso y bus CAN. El software empleado para la realización de la PCB es Orcad9.2/Layout. Para la evaluación de las medidas obtenidas por los sensores y la comprobación del bus CAN se emplea el kit de desarrollo de Microchip, MCP2515 CAN Bus Monitor Demo Board, que permite ver la información en el bus CAN e introducir tramas al mismo. ABSTRACT. This project develops an electronic system to vary the geometry of a car engine which runs the Formula SAE competition. Formula SAE is a design car competition for students, organized by "Society of Automotive Engineers" (SAE). This competition seeks technological innovation in the automotive industry and brings in students to participate in a real job, in which the objective is to obtain competitive results in compliance with certain requirements. Varying engine’s geometry in a vehicle improves car’s performance raising engine output torque. Any improvement in the vehicle in a competition field can be decisive in the outcome of it. The goal of the project is the variation by controlling the length of the air intake pipe or "runners" in a combustion engine, using a linear motor step. For these, uses the information gathered by speed sensors from the combustion engine and by the throttle position to control the distance of these tubes. This system is integrated in the vehicle CAN bus to share the information with the other modules. For all this is made a study to clarify the general aspects of the project in order to understand the activities developed inside the project, the different options available and also, to acquire knowledge for a better development of the project. The solution is based on linear stepper motor control by the microcontroller PIC32MX795F512-L. Device from manufacturer Microchip with a 32-bit architecture. This module has an integrated CAN various peripherals that are used in measuring the performance of the sensors and drives the stepper motor using Texas Instruments DRV8805 driver. Then the work is done in two lines, first, control programming software system using software MPLABX Microchip IDE and, second, hardware design of a PCB and conditioning circuits for connecting the microcontroller, with sensors, driver stepper motor and CAN bus. The software used to carry out the PCB is Orcad9.2/Layout. For the evaluation of the measurements obtained by the sensors and CAN bus checking is used Microchip development kit, MCP2515 CAN Bus Monitor Demo Board, that allows you to see the information on the CAN bus and enter new frames in the bus.

Sistema de telemetría para un vehículo de fórmula S.A.E.

En este proyecto, se ha desarrollado una aplicación electrónica para un coche de competición, en concreto para la fórmula SAE (Society of Automotive Engineers), una competición universitaria en la que cada equipo, formado por estudiantes, debe diseñar, construir y probar un prototipo basándose en una serie de reglas. El objetivo final de la competición es proporcionar a los estudiantes el conocimiento práctico necesario para su futura labor profesional, del cual se pensaba que los estudiantes adolecían al acabar sus estudios universitarios cuando se creó esta competición. La aplicación desarrollada en este proyecto consiste en un sistema de telemetría, utilizado para transmitir los datos proporcionados por los sensores del vehículo a través de un sistema de radiofrecuencia, de manera que se pueda estudiar el comportamiento del coche durante los ensayos a la vez que el coche está rodando y así no depender de un sistema de adquisición de datos del que había que descargarse la información una vez finalizada la sesión de ensayo, como había que hacer hasta el momento. Para la implementación del proyecto, se ha utilizado un kit de desarrollo (Xbee Pro 868) que incluye dos módulos de radio, dos placas de desarrollo, dos cables USB y una antena, el cual ha permitido desarrollar la parte de radio del proyecto. Para transmitir los datos proporcionados por la centralita del vehículo, la cual recoge la información de todos los sensores presentes en el vehículo, se han desarrollado dos placas de circuito impreso. La primera de ellas tiene como elemento principal un microprocesador PIC de la marca Microchip (PIC24HJ64GP502), que recoge los datos proporcionados por la centralita del vehículo a través de su bus CAN de comunicaciones. La segunda placa de circuito impreso tiene como elemento fundamental el transmisor de radio. Dicho transmisor está conectado al microprocesador de la otra placa a través de línea serie. Como receptor de radio se ha utilizado una de las placas de prueba que integraba el kit de desarrollo Xbee Pro 868, la cual recoge los datos que han sido enviados vía radio y los manda a su vez a través de USB a un ordenador donde son monitorizados. Hasta aquí la parte hardware del sistema. En cuanto a la parte software, ha habido que desarrollar una aplicación en lenguaje C, que ejecuta el microprocesador PIC, que se encarga de recoger los datos enviados por la centralita a través del bus CAN (Controller Area Network) y transmitirlos a través de línea serie al chip de radio. Por último, para la monitorización de los datos se han desarrollado dos aplicaciones en LabVIEW, una que recoge los datos a través de USB, los muestra en pantalla y los guarda en un fichero y otra que lee los datos del fichero y los representa gráficamente para permitir un estudio más detallado del comportamiento del vehículo. ABSTRACT In this project, an electronic application has been developed for a race car – Formula SAE car-. Formula SAE is a university championship in which each team, made up of students, should design, construct and test a prototype within certain rules. The final goal of the competition is to enhance the practical knowledge of the students, which was thougth to be poor at the time the competition was created. The application developed in this project consists of a telemetry system, employed to transmit the data provided by the car’s sensors through a radio frequency system, so that it could be possible to study the behaviour of the vehicle during tests and do not depend on a datalogger system as it occurred until now. To carry out the radio module of the project, a Xbee Pro 868 development kit has been used, which includes two radio modules, two development boards, two USB cables and an antenna. To transmit the data provided by the ECU (Engine Control Unit) of the vehicle, which receives information from all the sensors the vehicle has, two printed circuit boards have been built. One of them has a PIC microprocessor of Microchip (PIC24HJ64GP502) which receives the data coming from CAN bus of the ECU. Tha main element of the other printed circuit board is the radio transmitter. This chip receives the data from the microprocessor through its serial line. The development board of the Xbee Pro 868 has been used as receiver. When data arrives to the receiver, it transmits them to a computer through USB where the data are displayed. All this composes the hardware of the system. Regarding the software, a C coded application has been developed. This application is executed by the microprocessor and its function is to receive the data from the bus CAN (Controller Area Network) and send them to the radio transmitter through the microprocessor’s serial line. To show the data on the computer, two LabVIEW applications has been developed. The first one receives the data through the USB port, displays them on the screen and save them to a file and the second one reads the data from the file while represents them graphically to allow studying the behaviour of the car on track.

Electrodynamic tether for scientific mission in low Jovian orbit

An electrodynamic bare tether is shown to allow carrying out scientific observations very close to Jupiter, for exploration of its surface and subsurface, and ionospheric and atmospheric in-situ measurements. Starting at a circular equatorial orbit of radius about 1.3/1.4 times the Jovian radius, continuous propellantless Lorentz drag on a thin-tape tether in the 1-5 km length range would make a spacecraft many times as heavy as the tape slowly spiral in, over a period of many months, while generating power at a load plugged in the tether circuit for powering instruments in science data acquisition and transmission. Lying under the Jovian radiation belts, the tape would avoid the most severe problem facing tethers in Jupiter, which are capable of producing both power and propulsion but, operating slowly, could otherwise accumulate too high a radiation dose . The tether would be made to spin in its orbit to keep taut; how to balance the Lorentz torque is discussed. Constraints on heating and bowing are also discussed, comparing conditions for prograde versus retrograde orbits. The system adapts well to the moderate changes in plasma density and motional electric field through the limited radial range in their steep gradients near Jupiter.

Effect of magnetic field on current colection on bare tether in LEO

An eiectrodynamic Tether is a long thin conductive string deployed from a spacecraft. A part of the ED tether near one end, which is rendered positive by the Electromotive force (EMF)along the tether, collects electrons from the ambient plasma. In the frame of reference moving with theter, ions flow toward the tether, get deflected near the tether by its high positive potential and create a wake. Due to the asymmetry of plasma distribution and the weak but significant Geomagnetic field, the conventional probe theory becomes almost inapplicable. Computational work for the prediction of current collection is thus necessiated.. In this paper, we analyze effects of magnetic field on velocity distribution funtion at a point that is far from the tether, and discuss a new way to treat electrons at computational boundary. Three cases with different magnetic field are simulated and compiled so as to provide a part of the pre-flight prediction of the space experiment by NASA ProSEDS, which is planned September 2002.

A review of electrodynamic tethers for space applications

Space applications of electrodynamic tethers, and basic issues and constraints on their operation are reviewed. The status of the bare-tether solution to the problem of effective electron collection from a rarefied magnetized plasma is revisited. Basic modes of tether operation are analyzed; design parameters and parametric domains where a bare electrodynamic tether is most efficient in deorbiting, rebooking, or power generation, are determined. Use of bare tethers for Radiation Belt Remediation and generation of electron beams for ionospheric research is considered. Teiher heating, arcing, and bowing or breaking, as well deployment strategies are discussed.

Trade-off study on deorbiting S/C in near polar orbit

Usual long, flexible, ED tethers kept vertical by the gravity gradient might be less efficient for deorbiting S/C in near-polar orbits than conventional (Hall, Ion) electrical thrusters. A trade-off study on this application is here presented for tethers kept horizontal and perpendicular to the orbital plane. A tether thus oriented must be rigid and short for structural reasons, requiring a non-convex cross section and a power supply as in the case of electrical thrusters. Very recent developments on bare-tether collection theory allow predicting the current collected by an arbitrary cross section. For the horizontal tether, structural considerations on length play the role of ohmic effects in vertical tethers, in determining the optimal contribution of tether mass to the overall deorbiting system. For a given deorbiting-mission impulse, tether-system mass is minimal at some optimal length that increases weakly with the impulse. The horizontal-tether system may beat both the vertical tether and the electrical thruster as regards mass requirements for a narrow length range centered at about 100 m, allowing, however, for a broad mission-impulse range.

Estimación de variables dasométricas a partir de datos LiDAR y obtención de modelos de referencia para las distribuciones de alturas y diámetros del arbolado

La Gestión Forestal Sostenible se define como “la administración y uso de los bosques y tierras forestales de forma e intensidad tales que mantengan su biodiversidad, productividad, capacidad de regeneración, vitalidad y su potencial para atender, ahora y en el futuro, las funciones ecológicas, económicas y sociales relevantes a escala local, nacional y global, y que no causan daño a otros ecosistemas” (MCPFE Conference, 1993). Dentro del proceso los procesos de planificación, en cualquier escala, es necesario establecer cuál será la situación a la que se quiere llegar mediante la gestión. Igualmente, será necesario conocer la situación actual, pues marcará la situación de partida y condicionará el tipo de actuaciones a realizar para alcanzar los objetivos fijados. Dado que, los Proyectos de Ordenación de Montes y sus respectivas revisiones son herramientas de planificación, durante la redacción de los mismos, será necesario establecer una serie de objetivos cuya consecución pueda verificarse de forma objetiva y disponer de una caracterización de la masa forestal que permita conocer la situación de partida. Esta tesis se centra en problemas prácticos, propios de una escala de planificación local o de Proyecto de Ordenación de Montes. El primer objetivo de la tesis es determinar distribuciones diamétricas y de alturas de referencia para masas regulares por bosquetes, empleando para ello el modelo conceptual propuesto por García-Abril et al., (1999) y datos procedentes de las Tablas de producción de Rojo y Montero (1996). Las distribuciones de referencia obtenidas permitirán guiar la gestión de masas irregulares y regulares por bosquetes. Ambos tipos de masas aparecen como una alternativa deseable en aquellos casos en los que se quiere potenciar la biodiversidad, la estabilidad, la multifuncionalidad del bosque y/o como alternativa productiva, especialmente indicada para la producción de madera de calidad. El segundo objetivo de la Tesis está relacionado con la necesidad de disponer de una caracterización adecuada de la masa forestal durante la redacción de los Proyectos de Ordenación de Montes y de sus respectivas revisiones. Con el fin de obtener estimaciones de variables forestales en distintas unidades territoriales de potencial interés para la Ordenación de Montes, así como medidas de la incertidumbre en asociada dichas estimaciones, se extienden ciertos resultados de la literatura de Estimación en Áreas Pequeñas. Mediante un caso de estudio, se demuestra el potencial de aplicación de estas técnicas en inventario forestales asistidos con información auxiliar procedente de sensores láser aerotransportados (ALS). Los casos de estudio se realizan empleando datos ALS similares a los recopilados en el marco del Plan Nacional de Ortofotografía Aérea (PNOA). Los resultados obtenidos muestran que es posible aumentar la eficiencia de los inventarios forestales tradicionales a escala de proyecto de Ordenación de Montes, mediante la aplicación de estimadores EBLUP (Empirical Best Linear Unbiased Predictor) con modelos a nivel de elemento poblacional e información auxiliar ALS similar a la recopilada por el PNOA. ABSTRACT According to MCPFE (1993) Sustainable Forest Management is “the stewardship and use of forests and forest lands in a way, and at a rate, that maintains their biodiversity, productivity, regeneration capacity, vitality and their potential to fulfill, now and in the future, relevant ecological, economic and social functions, at local, national, and global levels, and that does not cause damage to other ecosystems”. For forest management planning, at any scale, we must determine what situation is hoped to be achieved through management. It is also necessary to know the current situation, as this will mark the starting point and condition the type of actions to be performed in order to meet the desired objectives. Forest management at a local scale is no exception. This Thesis focuses on typical problems of forest management planning at a local scale. The first objective of this Thesis is to determine management objectives for group shelterwood management systems in terms of tree height and tree diameter reference distributions. For this purpose, the conceptual model proposed by García-Abril et al., (1999) is applied to the yield tables for Pinus sylvestris in Sierra de Guadrrama (Rojo y Montero, 1996). The resulting reference distributions will act as a guide in the management of forests treated under the group shelterwood management systems or as an approximated reference for the management of uneven aged forests. Both types of management systems are desirable in those cases where forest biodiversity, stability and multifunctionality are pursued goals. These management systems are also recommended as alternatives for the production of high quality wood. The second objective focuses on the need to adequately characterize the forest during the decision process that leads to local management. In order to obtain estimates of forest variables for different management units of potential interest for forest planning, as well as the associated measures of uncertainty in these estimates, certain results from Small Area Estimation Literature are extended to accommodate for the need of estimates and reliability measures in very small subpopulations containing a reduced number of pixels. A case study shows the potential of Small Area Estimation (SAE) techniques in forest inventories assisted with remotely sensed auxiliary information. The influence of the laser pulse density in the quality of estimates in different aggregation levels is analyzed. This study considers low laser pulse densities (0.5 returns/m2) similar to, those provided by large-scale Airborne Laser Scanner (ALS) surveys, such as the one conducted by the Spanish National Geographic Institute for about 80% of the Spanish territory. The results obtained show that it is possible to improve the efficiency of traditional forest inventories at local scale using EBLUP (Empirical Best Linear Unbiased Predictor) estimators based on unit level models and low density ALS auxiliary information.