Study of Worker’s Exposure to Tantalum-bearing Particles in a Mining and Metallurgical Plant

The objective of this study was to assess worker exposure to mineral dust particles and a metabolic model, based on the model adopted by ICRP, was applied to assess human exposure to Ta, and predicted values of Ta concentrations in excreta. The occupational exposure to Th, U, Nb, and Ta bearing particles during routine tasks to obtain Fe-Nb alloys was estimated using air samplers and excreta samples. Ta concentrations in food samples and in drinking water were also determined. The results support that workers were occupationally exposed to Ta bearing particles, and also indicate that a source of Ta exposure for both workers and the control group was the ingestion of drinking water containing soluble compounds of Ta. Therefore, some Ta compounds should be considered soluble compounds in gastrointestinal tract. Consequently the metabolic model based on ICRP metabolic model and/or the transfer factor f1 for Ta should be reviewed and the solubility of Ta compounds in gastrointestinal should be determined.

Transport and health in China : recent collaborative research relating to vehicle factors and pollution

The nature of the transport system contributes to public health outcomes in a range of ways. The clearest contribution to public health is in the area of traffic crashes, because of their direct impact on individual death and disability and their direct costs to the health system. Other papers in this conference address these issues. This paper outlines some collaborative research between the Centre for Accident Research and Road Safety - Queensland (CARRS-Q) at QUT and Chinese researchers in areas that have indirect health impacts. Heavy vehicle dynamics: The integrity of the road surface influences crash risk, with ruts, pot-holes and other forms of road damage contributing to increased crash risks. The great majority of damage to the road surface from vehicles is caused by heavy trucks and buses, rather than cars or smaller vehicles. In some cases this damage is due to deliberate overloading, but in other cases it is due to vehicle suspension characteristics that lead to occasional high loads on particular wheels. Together with a visiting researcher and his colleagues, we have used both Queensland and Chinese data to model vehicle suspension systems that reduce the level of load, and hence the level of road damage and resulting crash risk(1-5). Toll worker exposure to vehicle emissions: The increasing construction of highways in China has also involved construction of a large number of toll roads. Tollbooth workers are potentially exposed to high levels of pollutants from vehicles, however the extent of this exposure and how it relates to standards for exposure are not well known. In a study led by a visiting researcher, we conducted a study to model these levels of exposure for a tollbooth in China(6). Noise pollution: The increasing presence of high speed roads in China has contributed to an increase in noise levels. In this collaborative study we modelled noise levels associated with a freeway widening near a university campus, and measures to reduce the noise(7). Along with these areas of research, there are many other areas of transport with health implications that are worthy of exploration. Traffic, noise and pollution contribute to a difficult environment for pedestrians, especially in an ageing society where there are health benefits to increasing physical activity. By building on collaborations such as those outlined, there is potential for a contribution to improved public health by addressing transport issues such as vehicle factors and pollution, and extending the research to other areas of travel activity. 1. Chen, Y., He, J., King, M., Chen, W. and Zhang, W. (2014). Stiffness-damping matching method of an ECAS system based on LQG control. Journal of Central South University, 21:439-446. DOI: 10.1007/s1177101419579 2. Chen, Y., He, J., King, M., Feng, Z. and Chang, W. (2013). Comparison of two suspension control strategies for multi-axle heavy truck. Journal of Central South University, 20(2): 550-562. 3. Chen, Y., He, J., King, M., Chen, W. and Zhang, W. (2013). Effect of driving conditions and suspension parameters on dynamic load-sharing of longitudinal-connected air suspensions. Science China Technological Sciences, 56(3): 666-676. DOI: 10.1007/s11431-012-5091-3 4. Chen, Y., He., J., King, M., Chen, W. and Zhang, W. (2013). Model development and dynamic load-sharing analysis of longitudinal-connected air suspensions. Strojniški Vestnik - Journal of Mechanical Engineering, 59(1):14-24. 5. Chen, Y., He, J., King, M., Liu, H. and Zhang, W. (2013). Dynamic load-sharing of longitudinal-connected air suspensions of a tri-axle semi-trailer. Proceedings of Transportation Research Board Annual Conference, Washington DC, 13-17 January 2013, paper no. 13-1117. 6. He, J., Qi, Z., Hang, W., King, M., and Zhao, C. (2011). Numerical evaluation of pollutant dispersion at a toll plaza based on system dynamics and Computational Fluid Dynamics models. Transportation Research Part C, 19(2011):510-520. 7. Zhang, C., He, J., Wang, Z., Yin, R. and King, M. (2013). Assessment of traffic noise level before and after freeway widening using traffic microsimulation and a refined classic noise prediction method. Proceedings of Transportation Research Board Annual Conference, Washington DC, 13-17 January 2013, paper no. 13-2016.

Metrological assessment of a portable analyzer for monitoring the particle size distribution of ultrafine particles

Adverse health effects caused by worker exposure to ultrafine particles have been detected in recent years. The scientific community focuses on the assessment of ultrafine aerosols in different microenvironments in order to determine the related worker exposure/dose levels. To this end, particle size distribution measurements have to be taken along with total particle number concentrations. The latter are obtainable through hand-held monitors. A portable particle size distribution analyzer (Nanoscan SMPS 3910, TSI Inc.) was recently commercialized, but so far no metrological assessment has been performed to characterize its performance with respect to well-established laboratory- based instruments such as the scanning mobility particle sizer (SMPS) spectrometer. The present paper compares the aerosol monitoring capability of the Nanoscan SMPS to the laboratory SMPS in order to evaluate whether the Nanoscan SMPS is suitable for field experiments designed to characterize particle exposure in different microenvironments. Tests were performed both in a Marple calm air chamber, where fresh diesel particulate matter and atomized dioctyl phthalate particles were monitored, and in microenvironments, where outdoor, urban, indoor aged, and indoor fresh aerosols were measured. Results show that the Nanoscan SMPS is able to properly measure the particle size distribution for each type of aerosol investigated, but it overestimates the total particle number concentration in the case of fresh aerosols. In particular, the test performed in the Marple chamber showed total concentrations up to twice those measured by the laboratory SMPS—likely because of the inability of the Nanoscan SMPS unipolar charger to properly charge aerosols made up of aggregated particles. Based on these findings, when field test exposure studies are conducted, the Nanoscan SMPS should be used in tandem

A Videogrammetric As-Built Data Collection Method for Digital Fabrication of Sheet Metal Roof Panels

A roofing contractor typically needs to acquire as-built dimensions of a roof structure several times over the course of its build to be able to digitally fabricate sheet metal roof panels. Obtaining these measurements using the exiting roof surveying methods could be costly in terms of equipment, labor, and/or worker exposure to safety hazards. This paper presents a video-based surveying technology as an alternative method which is simple to use, automated, less expensive, and safe. When using this method, the contractor collects video streams with a calibrated stereo camera set. Unique visual characteristics of scenes from a roof structure are then used in the processing step to automatically extract as-built dimensions of roof planes. These dimensions are finally represented in a XML format to be loaded into sheet metal folding and cutting machines. The proposed method has been tested for a roofing project and the preliminary results indicate its capabilities.

Cancer mortality in IBM endicott plant workers, 1969-2001: An update on a NY production plant

BACKGROUND: In response to concerns expressed by workers at a public meeting, we analyzed the mortality experience of workers who were employed at the IBM plant in Endicott, New York and died between 1969-2001. An epidemiologic feasibility assessment indicated potential worker exposure to several known and suspected carcinogens at this plant. METHODS: We used the mortality and work history files produced under a court order and used in a previous mortality analysis. Using publicly available data for the state of New York as a standard of comparison, we conducted proportional cancer mortality (PCMR) analysis. RESULTS: The results showed significantly increased mortality due to melanoma (PCMR = 367; 95% CI: 119, 856) and lymphoma (PCMR = 220; 95% CI: 101, 419) in males and modestly increased mortality due to kidney cancer (PCMR = 165; 95% CI: 45, 421) and brain cancer (PCMR = 190; 95% CI: 52, 485) in males and breast cancer (PCMR = 126; 95% CI: 34, 321) in females. CONCLUSION: These results are similar to results from a previous IBM mortality study and support the need for a full cohort mortality analysis such as the one being planned by the National Institute for Occupational Safety and Health.

Fungal contamination in two Portuguese wastewater treatment plants

The presence of filamentous fungi was detected in wastewater and air collected at wastewater treatment plants (WWTP) from several European countries. The aim of the present study was to assess fungal contamination in two WWTP operating in Lisbon. In addition, particulate matter (PM) contamination data was analyzed. To apply conventional methods, air samples from the two plants were collected through impaction using an air sampler with a velocity air rate of 140 L/min. Surfaces samples were collected by swabbing the surfaces of the same indoor sites. All collected samples were incubated at 27°C for 5 to 7 d. After lab processing and incubation of collected samples, quantitative and qualitative results were obtained with identification of the isolated fungal species. For molecular methods, air samples of 250 L were also collected using the impinger method at 300 L/min airflow rate. Samples were collected into 10 ml sterile phosphate-buffered saline with 0.05% Triton X-100, and the collection liquid was subsequently used for DNA extraction. Molecular identification of Aspergillus fumigatus and Stachybotrys chartarum was achieved by real-time polymerase chain reaction (RT-PCR) using the Rotor-Gene 6000 qPCR Detection System (Corbett). Assessment of PM was also conducted with portable direct-reading equipment (Lighthouse, model 3016 IAQ). Particles concentration measurement was performed at five different sizes: PM0.5, PM1, PM2.5, PM5, and PM10. Sixteen different fungal species were detected in indoor air in a total of 5400 isolates in both plants. Penicillium sp. was the most frequently isolated fungal genus (58.9%), followed by Aspergillus sp. (21.2%) and Acremonium sp. (8.2%), in the total underground area. In a partially underground plant, Penicillium sp. (39.5%) was also the most frequently isolated, also followed by Aspergillus sp. (38.7%) and Acremonium sp. (9.7%). Using RT-PCR, only A. fumigatus was detected in air samples collected, and only from partial underground plant. Stachybotrys chartarum was not detected in any of the samples analyzed. The distribution of particle sizes showed the same tendency in both plants; however, the partially underground plant presented higher levels of contamination, except for PM2.5. Fungal contamination assessment is crucial to evaluating the potential health risks to exposed workers in these settings. In order to achieve an evaluation of potential health risks to exposed workers, it is essential to combine conventional and molecular methods for fungal detection. Protective measures to minimize worker exposure to fungi need to be adopted since wastewater is the predominant internal fungal source in this setting.

Remoção de fibrocimento: amianto

Dissertação para obtenção do grau de Mestre em Engenharia Civil Ramo Edificações

Relación entre los hallazgos radiográficos y la sintomatología respiratoria en trabajadores expuestos a polvo de carbón en minería de socavón en el departamento de Boyacá, Colombia 2015

Introducción: La inhalación de polvo de carbón favorece el desarrollo de neumoconiosis, causa daños irreversibles al pulmón que se identifican radiológicamente. Los síntomas son tardíos y la patología se puede desarrollar tras varios años de exposición. Objetivo: Caracterizar los hallazgos radiográficos según la metodología de la Organización Internacional del Trabajo (OIT) 2000 y relacionarlos con la sintomatología respiratoria en trabajadores expuestos a polvo de carbón en las labores de minería de socavón en el departamento de Boyacá, Colombia, 2015. Materiales y métodos: Estudio de corte transversal realizado en 232 mineros, se indagó características sociodemográficas, signos y síntomas del sistema respiratorio. Se realizó radiografías de tórax y se aplicó la metodología OIT para describir los hallazgos. Se estableció asociación estadística a través de la prueba Chi cuadrado de Pearson. Para el procesamiento de la información se utilizó el programa SPSS statistics 2.3 Resultados: Toda la población fue de sexo masculino, con una edad promedio de 40,8 años. El cargo de picador fue el más frecuente en 72,4% de los trabajadores. Las radiografías mostraron opacidades pequeñas redondeadas (q/q) en 42%. La expectoración fue el síntoma más frecuente 66,4%. Se encontró una relación estadísticamente significativa entre el tabaquismo con las anomalía parenquimatosas (p=0,002).Conclusión: La prevalencia de neumoconiosis para el departamento de Boyacá fue de 29.7% entre los trabajadores valorados según los criterios OIT para lectura de radiografías de tórax, por lo que se requiere poner en práctica medidas de control a fin de reducir al mínimo la exposición de los trabajadores.

Process evaluation of an integrated health promotion/occupational health model in WellWorks-2

Disparities in chronic disease risk by occupation call for newapproaches to health promotion. Well Works-2 was a randomized, controlled study comparing the effectiveness of a health promotion/occupational health program (HP/OHS) with a standard intervention (HP). Interventions in both studies were based on the same theoretical foundations. Results from process evaluation revealed that a similar number of activities were offered in both conditions and that in the HP/OHS condition there were higher levels of worker participation using three measures: mean participation per activity (HP: 14.2% vs. HP/OHS: 21.2%), mean minutes of worker exposure to the intervention/site (HP: 14.9 vs. HP/OHS: 33.3), and overall mean participation per site (HP: 34.4% vs. HP/ OHS: 45.8%). There were a greater number of contacts with management (HP: 8.8 vs. HP/OHS: 24.9) in the HP/ OHS condition. Addressing occupational health may have contributed to higher levels of worker and management participation and smoking cessation among blue-collar workers.

Avaliação de equipamentos de aplicação de herbicidas em operação de repasse em cana-de-açúcar e segurança para o trabalhador

Objetivou-se com este trabalho classificar em seguras ou inseguras as condições de trabalho de aplicação da formulação comercial de paraquat a 0,5% e de abastecimento dos tanques em operação de repasse em cultura de cana-de-açúcar com os pulverizadores costal manual, costal pressurizado e Pulmipur manual; determinar o efeito das variações na operação de repasse em quatro usinas de açúcar e álcool com o pulverizador costal pressurizado sobre as exposições dos trabalhadores ao paraquat; determinar a eficácia de equipamentos de proteção individual nessas condições de trabalho; e avaliar a intensidade da deriva e a eficácia de acessórios protetores de deriva. As exposições dérmicas e respiratórias dos trabalhadores foram avaliadas e utilizadas para calcular a margem de segurança (MS). Os valores de MS foram utilizados para classificar essas condições de trabalho em seguras (MS > 1) ou em inseguras (MS < 1). Para avaliar a deriva das aplicações na cultura e a eficácia dos protetores de deriva, foram estudados os tratamentos: formulação comercial de paraquat a 0,5% na calda, aplicada com o costal manual, sem e com o chapéu de proteção de deriva; com o costal pressurizado, sem e com a planilha de proteção de deriva; formulação comercial de paraquat pura com o Pulmipur; formulação comercial de glyphosate a 1% com o costal pressurizado e com a planilha, e puro com o Pulmipur; e testemunha sem aplicação. As duas atividades com o Pulmipur proporcionam as maiores exposições dérmicas, devido ao manuseio da formulação, e são inseguras sem o uso dos EPIs e seguras com estes. As atividades com o pulverizador costal manual ou pressurizado são seguras com ou sem os EPIs. As grandes diferenças nas EDs dos trabalhadores se devem às diferenças no tempo de trabalho diário e no número de trabalhadores nas equipes entre as usinas de açúcar e álcool. O protetor de deriva tipo chapéu é eficaz no controle da deriva na aplicação do paraquat, e a planilha, não.

Safety by design: production of engineering surface modified nanomaterials

This PhD thesis focused on nanomaterial (NM) engineering for occupational health and safety, in the frame of the EU project “Safe Nano Worker Exposure Scenarios (SANOWORK)”. Following a safety by design approach, surface engineering (surface coating, purification process, colloidal force control, wet milling, film coating deposition and granulation) were proposed as risk remediation strategies (RRS) to decrease toxicity and emission potential of NMs within real processing lines. In the first case investigated, the PlasmaChem ZrO2 manufacturing, the colloidal force control applied to the washing of synthesis rector, allowed to reduce ZrO2 contamination in wastewater, performing an efficient recycling procedure of ZrO2 recovered. Furthermore, ZrO2 NM was investigated in the ceramic process owned by CNR-ISTEC and GEA-Niro; the spray drying and freeze drying techniques were employed decreasing NM emissivity, but maintaining a reactive surface in dried NM. Considering the handling operation of nanofibers (NFs) obtained through Elmarco electrospinning procedure, the film coating deposition was applied on polyamide non-woven to avoid free fiber release. For TiO2 NF the wet milling was applied to reduce and homogenize the aspect ratio, leading to a significant mitigation of fiber toxicity. In the Colorobbia spray coating line, Ag and TiO2 nanosols, employed to transfer respectively antibacterial or depolluting properties to different substrates, were investigated. Ag was subjected to surface coating and purification, decreasing NM toxicity. TiO2 was modified by surface coating, spray drying and blending with colloidal SiO2, improving its technological performance. In the extrusion of polymeric matrix charged with carbon nanotube (CNTs) owned by Leitat, the CNTs used as filler were granulated by spray drying and freeze spray drying techniques, allowing to reduce their exposure potential. Engineered NMs tested by biologists were further investigated in relevant biological conditions, to improve the knowledge of structure/toxicity mechanisms and obtain new insights for the design of safest NMs.

Dermal deposition of diazinon on workers using various sheep ectoparasiticide application systems

This study measured the dermal deposition levels of diazinon on workers who apply the ectoparasiticide to sheep using one of five different application systems, namely, portable plunge dipping, fixed plunge dipping, shower dipping, hand jetting, and automatic jetting races. The highest level of dermal exposure occurred while hand jetting and a comparable level occurred in automatic jetting races. The next highest level of dermal exposure was while using the portable and the fixed plunge dipping systems. The shower dipping system appeared to expose workers to the least deposition of diazinon. The variability between the different methods was statistically significant, and the contrast between the three applications using dipping and the two using jetting was highly statistically significant. The variability between testing sessions was too great to allow the methods to be ranked as accurately as the authors would prefer. However, the differences between the methods were large enough to be of practical importance to OHS risk management. (author abstract)

Prevalence of Aspergillus fumigatus complex in waste sorting and incineration plants: an occupational threat

Aspergillus fumigatus is one of the major ubiquitous saprophytic fungi and it is considered one of the fungal species with higher clinical relevance. This study aimed at characterising the prevalence of A. fumigatus complex in one waste-sorting plant and also in one incineration plant. Conventional and molecular methodologies were applied in order to detect its presence. Aspergillus fumigatus complex was the second most frequently found in the air from the waste-sorting plant (16.0%) and from the incineration plant (18.0%). Regarding surfaces, it ranked the third species most frequently found in the waste-sorting plant (13.8%) and the second in the incineration plant (22.3%). In the waste-sorting plant, it was possible to amplify by qPCR DNA from the A. fumigatus complex in all culture-positive sampling sites plus one other sampling site that was negative by culture analysis. Considering the observed fungal load, it is recommended to apply preventive and protective measures in order to avoid or minimise worker's exposure.